- aggiunti i messaggi da accodare ai messaggi generali

- in FaceData si accettano, solo per le groove-3, i MainEdges per LongFaces a 5 lati
- in FACEBYCHAINSAW modifiche per rispecchiare la direzione utensile calcolata dal Cam5 e MaxElev impostata di conseguenza; invece di usare formule si provano sempre entrambe le soluzioni BlockedAxis, per contemplare tutti i casi

BatchProcessNew.lua

@@ -250,6 +250,7 @@ elseif BEAM.FLAG == 9 then
       local Proc = FeatureLib.GetProcFromTrimesh( BEAM.FEATUREID, Part)
       Proc.nGrp = EgtGetInfo( Proc.id, 'GRP', 'i')
       Proc.nPrc = EgtGetInfo( Proc.id, 'PRC', 'i')
+      Proc.nParts = EgtSurfTmPartCount( Proc.id) or 1
 
       Proc.Topology = {}
       if FeatureLib.NeedTopologyFeature( Proc, Part) then
@@ -387,6 +388,15 @@ if bToProcess then
             else
                PARTS[i].b3PartOriginal = b3Solid
             end
+            if BeamData.MAX_LENGTH and BeamData.MAX_LENGTH > 10 and b3Solid:getDimX() > BeamData.MAX_LENGTH then
+               local sOut = 'Piece-Length ('  .. EgtNumToString( b3Solid:getDimX(), 2) .. ') ' ..
+                         'out of machine limits (' .. EgtNumToString( BeamData.MAX_LENGTH, 2) .. ') '
+               BEAM.ERR = 17
+               BEAM.MSG = sOut
+               WriteErrToLogFile( BEAM.ERR, BEAM.MSG)
+               PostErrView( BEAM.ERR, BEAM.MSG)
+               return
+            end
          end
          -- Assegno lunghezza della barra
          dBarLen = PARTS[1].b3PartOriginal:getDimX() + 10
@@ -446,6 +456,15 @@ if bToProcess then
          else
             PARTS[i].b3PartOriginal = b3Solid
          end
+         if BeamData.MAX_LENGTH and BeamData.MAX_LENGTH > 10 and b3Solid:getDimX() > BeamData.MAX_LENGTH then
+            local sOut = 'Piece-Length ('  .. EgtNumToString( b3Solid:getDimX(), 2) .. ') ' ..
+                         'out of machine limits (' .. EgtNumToString( BeamData.MAX_LENGTH, 2) .. ') '
+            BEAM.ERR = 17
+            BEAM.MSG = sOut
+            WriteErrToLogFile( BEAM.ERR, BEAM.MSG)
+            PostErrView( BEAM.ERR, BEAM.MSG)
+            return
+         end
       end
    end
 
@@ -491,6 +510,7 @@ if bToProcess then
          return
       end
 
+      -- TODO in caso di  "GEN_sPiecesLoadingPosition = FULL_PRE_ROTATION"  bisogna controllare anche sezione ribaltata di 90°
       -- Verifico sezione barra non troppo grande
       if not BeamData.MAX_WIDTH2 or not BeamData.MAX_HEIGHT2 then
          if ( dRawW > BeamData.MAX_WIDTH + 10 * GEO.EPS_SMALL or dRawH > BeamData.MAX_HEIGHT + 10 * GEO.EPS_SMALL) then
@@ -548,7 +568,7 @@ if bToProcess then
       end
       
       -- Sistemo le travi nel grezzo
-      local bPbOk, sPbErr = BeamExec.ProcessBeams( dRawW, dRawH, dRawL, dOvmHead, nil, PARTS, BEAM.FLAG ~= 6, false)
+      local bPbOk, sPbErr = BeamExec.ProcessBeams( dRawW, dRawH, dRawL, dOvmHead, nil, PARTS, BEAM.FLAG ~= 6, BEAM.FLAG == 10)
       if not bPbOk then
          BEAM.ERR = 18
          BEAM.MSG = sPbErr
@@ -637,6 +657,7 @@ if bToProcess then
          BeamExec.GetStrategiesFromJSONinBD( PARTS[i].sAISetupConfig)
          PARTS[i].GeneralParameters = BeamLib.GetPieceGeneralParameters( PARTS[i], GENERAL_PARAMETERS_JSON)
          TIMER:stopElapsed('Json')
+         -- parametro FlipRot sempre a false perchè a barra già creata non si possono più ruotare i pezzi
          PARTS[i].CombinationList = BeamExec.GetAvailableCombinations( PARTS[i], false)
 
          -- sovramateriale in testa al pezzo
@@ -690,12 +711,9 @@ if bToProcess then
    -- TODO gestire errori e messaggi di ritorno in questo caso
    if not GetDataConfig() then return end
 
-   BeamExec.GetProcessings( PARTS, false)
-   BeamExec.GetCombinationMatrix( PARTS, false)
-   BeamExec.ProcessMachinings( PARTS)
-
-   -- si cancella gruppo temporaneo contenente entità da cancellare
-   EgtErase( idTempGroup)
+   BeamExec.GetProcessings( PARTS, BEAM.FLAG == 10)
+   BeamExec.GetCombinationMatrix( PARTS, BEAM.FLAG == 10)
+   BeamExec.ProcessMachinings( PARTS, BEAM.FLAG == 10)
 
    local sOutput = ''
 
@@ -722,7 +740,7 @@ if bToProcess then
             BEAM.ERR = 0
             BEAM.MSG = '---'
          end
-         BEAM.ROT = -( RESULT[i].nRotation or 1) + 1
+         BEAM.ROT = -( ( RESULT[i].nRotation - ( BEAM.PREROTATE90 or 0)) or 1) + 1
          BEAM.CUTID = RESULT[i].idCut
          BEAM.TASKID = RESULT[i].idTask
          WriteErrToLogFile( BEAM.ERR, BEAM.MSG, BEAM.ROT, BEAM.CUTID, BEAM.TASKID)
@@ -738,7 +756,7 @@ if bToProcess then
          sOutput = sOutput .. string.format( '[%d,%d] %s\n', RESULT[i].idCut, RESULT[i].idTask, sMsg)
          BEAM.ERR = 19
          BEAM.MSG = sMsg
-         BEAM.ROT = -( RESULT[i].nRotation or 1) + 1
+         BEAM.ROT = -( ( RESULT[i].nRotation - ( BEAM.PREROTATE90 or 0)) or 1) + 1
          BEAM.CUTID = RESULT[i].idCut
          BEAM.TASKID = RESULT[i].idTask
          WriteErrToLogFile( BEAM.ERR, BEAM.MSG, BEAM.ROT, BEAM.CUTID, BEAM.TASKID)
@@ -764,7 +782,7 @@ if bToProcess then
             sOutput = sOutput .. string.format( '[%d,%d] %s\n', RESULT[i].idCut, RESULT[i].idTask, sMsg)
             BEAM.ERR = -19
             BEAM.MSG = 'Incomplete : Completion index ' .. RESULT[i].ChosenStrategy.dCompletionIndex .. '/5\n' .. sMsg
-            BEAM.ROT = -( RESULT[i].nRotation or 1) + 1
+            BEAM.ROT = -( ( RESULT[i].nRotation - ( BEAM.PREROTATE90 or 0)) or 1) + 1
             BEAM.CUTID = RESULT[i].idCut
             BEAM.TASKID = RESULT[i].idTask
             WriteErrToLogFile( BEAM.ERR, BEAM.MSG, BEAM.ROT, BEAM.CUTID, BEAM.TASKID)
@@ -772,6 +790,16 @@ if bToProcess then
       end
    end
 
+   -- calcolo alternative (scrive già le variabili globali per interfaccia)
+   if BEAM.FLAG == 10 then
+      TIMER:startElapsed('Alternatives')
+      BeamExec.ProcessAlternatives( PARTS)
+      TIMER:stopElapsed('Alternatives')
+   end
+
+   -- si cancella gruppo temporaneo contenente entità da cancellare
+   EgtErase( idTempGroup)
+
    -- TODO: se scarico a caduta (-101, -102) le lavorazioni dopo separazione vanno disattivate. Scrivere info feature incompleta su quelle feature 
 
    -- Salvo il progetto

FlipRot.lua

@@ -145,7 +145,12 @@ local function MyProcessFeatures()
 
    BeamExec.GetProcessings( PARTS, true)
    BeamExec.GetCombinationMatrix( PARTS, true)
-   BeamExec.ProcessMachinings( PARTS)
+   BeamExec.ProcessMachinings( PARTS, true)
+
+   -- scrittura variabili globali per interfaccia
+   BEAM.PREROTATE90 = PARTS[1].nInitialPosition - 1
+   BEAM.PREINVERT = EgtIf( PARTS[1].bPartInCombiIsInverted, 1, 0)
+
    local nErrCnt = 0
    local nWarnCnt = 0
    local sOutput = ''

GetBeamData.lua

@@ -0,0 +1,44 @@
+-- GetWallData.lua by Egaltech s.r.l. 2022/06/28
+-- Recupero dati da file WallData.lua di macchina
+
+-- Intestazioni
+require( 'EgtBase')
+_ENV = EgtProtectGlobal()
+EgtEnableDebug( false)
+
+-- Per test
+--GWD = {}
+--GWD.MACHINE = 'Essetre-90480019_MW'
+
+local sLog = 'GetBeamData : ' .. GWD.MACHINE
+EgtOutLog( sLog)
+
+-- Imposto direttorio libreria specializzata per Travi
+EgtAddToPackagePath( GWD.BASEDIR .. '\\LuaLibs\\?.lua')
+
+-- Verifico che la macchina corrente sia abilitata per la lavorazione delle Travi
+local sMachDir = EgtGetCurrMachineDir()
+if not EgtExistsFile( sMachDir .. '\\Beam\\BeamDataNew.lua') then
+   GWD.ERR = 12
+   GWD.MSG = 'Error not configured for beam machine : ' .. GWD.MACHINE
+   WriteErrToLogFile( GWD.ERR, GWD.MSG)
+   PostErrView( GWD.ERR, GWD.MSG)
+   return
+end
+
+-- Elimino direttori altre macchine e imposto direttorio macchina corrente per ricerca librerie
+EgtRemoveBaseMachineDirFromPackagePath()
+EgtAddToPackagePath( sMachDir .. '\\Beam\\?.lua')
+
+-- Carico i dati globali
+_G.package.loaded.BeamData = nil
+local BD = require( 'BeamDataNew')
+
+-- Assegno valori di interesse
+GWD.SIMUL_VIEW_DIR = BD.SIMUL_VIEW_DIR
+GWD.OVM_MID = BD.OVM_MID
+
+-- Tutto ok
+GWD.ERR = 0
+
+EgtOutLog( ' +++ GetBeamData completed')

LuaLibs/BasicCustomerStrategies.lua

@@ -252,6 +252,7 @@ local function GetStrategies_Essetre( Proc)
    ---------------------------------------------------------------------
    -- Feature : Chamfer (0-36)
    elseif ID.IsChamfer( Proc) then
+      Strategies = { { sStrategyId = 'STR0002'}, { sStrategyId = 'STR0005'}, { sStrategyId = 'STR0010'}}
    ---------------------------------------------------------------------
    -- Feature : Block Haus Half Lap (0-37)
    elseif ID.IsHalfBlockHaus( Proc) then

LuaLibs/BeamLib.lua

@@ -161,17 +161,45 @@ function BeamLib.GetPartSplittingPoints( Part)
 end
 
 -------------------------------------------------------------------------------------------------------------
-function BeamLib.AddPhaseWithRawParts( idRaw, OriXR, PosXR, dDeltaSucc)
+function BeamLib.AddPhaseWithRawParts( PARTS, nPartIndex, OriXR, PosXR, dDeltaSucc)
    local nPhase = EgtAddPhase()
+   local Part
+   local idRaw
+   -- se l'indice è oltre significa che è l'ultimo grezzo senza pezzi
+   if nPartIndex > #PARTS then
+      idRaw = EgtGetNextRawPart( PARTS[#PARTS].idRaw)
+   else
+      Part = PARTS[nPartIndex]
+      idRaw = Part.idRaw
+   end
    -- si aprono i limiti tavola per permettere rotazioni di pezzi più larghi della tavola
    EgtSetTableAreaOffset( 2000, 2000, 2000, 2000)
    local dRawMove = 0
+   local bIsFirstRaw = true
+   local dPosXFirst = 0
    while idRaw do
+      local dPosX
+      for i = 1, #PARTS do
+         local CurrentPart = PARTS[i]
+         if CurrentPart.idRaw == idRaw then
+            dPosX = CurrentPart.dPosX
+            if bIsFirstRaw then
+               dPosXFirst = dPosX
+            end
+            break
+         end
+         if i == #PARTS then
+            dPosX = PARTS[i].dPosX + PARTS[i].b3Raw:getDimX()
+         end
+      end
+      if bIsFirstRaw then
+         bIsFirstRaw = false
+      else
+         dRawMove = dDeltaSucc + dPosX - dPosXFirst
+      end
       EgtKeepRawPart( idRaw)
       EgtMoveToCornerRawPart( idRaw, OriXR, PosXR)
       EgtMoveRawPart( idRaw, Vector3d( - dRawMove, 0, 0))
-      if dRawMove == 0 then dRawMove = dRawMove + dDeltaSucc end
-      dRawMove = dRawMove + EgtGetRawPartBBox( idRaw):getDimX()
       idRaw = EgtGetNextRawPart( idRaw)
    end
    -- salvo info nuova fase aggiunta
@@ -395,6 +423,24 @@ function BeamLib.GetAddGroup( PartId)
    return AddGrpId, sMchGrp
 end
 
+-------------------------------------------------------------------------------------------------------------
+-- Funzione prossimo nome MachGroup libero (numero intero)
+function BeamLib.GetNewMachGroupName()
+   local idMachGroup = EgtGetFirstMachGroup()
+   if not idMachGroup then return 1 end
+   local nMaxMachGroup = 0
+   while idMachGroup do
+      local sMachGroupName = EgtGetMachGroupName( idMachGroup)
+      local nMachGroupName = tonumber( sMachGroupName)
+      if nMachGroupName > nMaxMachGroup then
+         nMaxMachGroup = nMachGroupName
+      end
+      idMachGroup = EgtGetNextMachGroup( idMachGroup)
+   end
+   
+   return nMaxMachGroup + 1
+end
+
 -------------------------------------------------------------------------------------------------------------
 -- restituisce le facce della parte interessate dalla feature Proc
 -- TODO da spostare in FeatureLib???
@@ -512,10 +558,69 @@ function BeamLib.GetDirectionFromSCC( nSCC)
    elseif nSCC == MCH_SCC.ADIR_ZM then
       vtSCC = -Z_AX()
    end
-   
+
    return vtSCC
 end
 
+-------------------------------------------------------------------------------------------------------------
+-- Restituisce una tabella con i punti ai vertici della faccia, in globale
+-- ordinati partendo da quello ai valori minimi degli assi e i successivi secondo rotazione destrorsa X+;
+-- solo per Proc a 1 faccia
+function BeamLib.GetSortedVertices( Proc)
+   local PtVerticesSorted = {}
+
+   -- se più di una faccia si esce subito
+   if Proc.nFct > 1 then
+      return
+   end
+
+   local PtVertices = {}
+   local nFirstIndex
+   local dMinYZ = GEO.INFINITO
+   for i = 1, #Proc.Faces[1].Edges do
+      local Edge = Proc.Faces[1].Edges[i]
+      table.insert( PtVertices, Edge.ptStart)
+      if ( Edge.ptStart:getY() + Edge.ptStart:getZ() < dMinYZ) then
+         nFirstIndex = i
+         dMinYZ = Edge.ptStart:getY() + Edge.ptStart:getZ()
+      end
+   end
+
+   table.insert( PtVerticesSorted, PtVertices[nFirstIndex])
+   local nCurrentIndex = nFirstIndex
+   -- faccia che guarda verso X+, ordine ok
+   if Proc.Faces[1].vtN:getX() > GEO.EPS_SMALL then
+      for _ = 1, #PtVertices - 1 do
+         _, nCurrentIndex = BeamLib.GetAdjacentIndices( nCurrentIndex, #PtVertices)
+         table.insert( PtVerticesSorted, PtVertices[nCurrentIndex])
+      end
+   -- faccia che guarda verso X-, ordine da invertire
+   else
+      for _ = 1, #PtVertices - 1 do
+         nCurrentIndex = BeamLib.GetAdjacentIndices( nCurrentIndex, #PtVertices)
+         table.insert( PtVerticesSorted, PtVertices[nCurrentIndex])
+      end
+   end
+
+   return PtVerticesSorted
+end
+
+-------------------------------------------------------------------------------------------------------------
+-- restituisce il precedente e prossimo indice 1-based, tenendo conto del massimo indice
+function BeamLib.GetAdjacentIndices( nCurrentIndex, nMaxIndex)
+   local nPreviousIndex, nNextIndex
+
+   if ( nCurrentIndex < 1) or ( nCurrentIndex > nMaxIndex) then
+      return
+   end
+
+   -- circular indexing 1-based
+   nPreviousIndex = ( ( nCurrentIndex - 2 + nMaxIndex) % nMaxIndex) + 1
+   nNextIndex = ( nCurrentIndex % nMaxIndex) + 1
+
+   return nPreviousIndex, nNextIndex
+end
+
 -------------------------------------------------------------------------------------------------------------
 -- Funzione per determinare se la faccia ha lati molto corti (trascurabili) ed è quindi approssimabile ad una 3 facce
 function BeamLib.Is3EdgesApprox( Proc, idFace, nAddGrpId)
@@ -785,17 +890,18 @@ function BeamLib.BinaryToDecimal( dNumber)
    local sNumberToConvert = tostring( dNumber)
    local dResult = 0
    local k = 0
-   
+
    for i = #sNumberToConvert, 1, -1 do
       k = k + 1
-      local n = string.sub(sNumberToConvert, k, k)
-      dResult = dResult + n*(2^(i-1))
+      local n = string.sub( sNumberToConvert, k, k)
+      dResult = dResult + n * ( 2^( i-1))
    end
-   
+
    return dResult
 end
 
 -------------------------------------------------------------------------------------------------------------
+-- TODO si può sostituire con funzione EgtNumToBitString
 function BeamLib.DecimalToBinary( dNumber)
    local sNumberToConvert = tostring( dNumber)
    local n = sNumberToConvert
@@ -803,12 +909,12 @@ function BeamLib.DecimalToBinary( dNumber)
    local sResult = ""
    
    for i = sNumberToConvert, 0, -1 do
-       local q = math.modf(n)
-       n = n/2
-       local b = q%2
-       table.insert(tmp, b)
+       local q = math.modf( n)
+       n = n / 2
+       local b = q % 2
+       table.insert( tmp, b)
 
-       if (q == 1) then
+       if ( q == 1) then
           break
        end
    end
@@ -816,7 +922,7 @@ function BeamLib.DecimalToBinary( dNumber)
    for i = #tmp, 1, -1 do
      sResult = sResult..tmp[i]
    end
-   
+
    return tonumber( sResult)
 end
 
@@ -830,6 +936,43 @@ function BeamLib.CalculateStringBinaryFormat( dNumber, CharNumber)
    return NumberString
 end
 
+-------------------------------------------------------------------------------------------------------------
+function BeamLib.ConvertBitIndexToRotationIndex( sBitIndexCombination)
+   local nRotationIndex
+
+   if sBitIndexCombination == '1000' then
+      return 1
+   elseif sBitIndexCombination == '0100' then
+      return 2
+   elseif sBitIndexCombination == '0010' then
+      return 3
+   elseif sBitIndexCombination == '0001' then
+      return 4
+   elseif sBitIndexCombination == '1000_INV' then
+      return 5
+   elseif sBitIndexCombination == '0100_INV' then
+      return 6
+   elseif sBitIndexCombination == '0010_INV' then
+      return 7
+   elseif sBitIndexCombination == '0001_INV' then
+      return 8
+   end
+
+   return nRotationIndex
+end
+
+-------------------------------------------------------------------------------------------------------------
+-- reindicizza una tabella passata ripartendo dall'indice nStartIndex e mantenendo l'ordine
+function BeamLib.RotateTableFromIndex( Table, nStartIndex)
+    local RotatedTable = {}
+
+    for i = 1, #Table do
+        RotatedTable[#RotatedTable + 1] = Table[((RotatedTable + i - 2) % #Table) + 1]
+    end
+
+    return RotatedTable
+end
+
 -------------------------------------------------------------------------------------------------------------
 --- copia una tabella lua in modo ricorsivo, ossia mantiene indipendenti anche tutte le sottotabelle
 --- ATTENZIONE: in caso di modifiche vanno gestiti anche i tipi custom; sarebbe meglio metterla nel LuaLibs

LuaLibs/DiceCut.lua

@@ -453,7 +453,7 @@ function DiceCut.GetDice( Part, Face1, Face2, OptionalParameters)
    -- se piani non ortogonali, diminuisco la distanza di offset opportunamente
    local dOffsetParallelOriginal = dOffsetParallel
    if not bGetOrtoPlanes then
-      local dCoeff = ( vtNMainFace ^ vtNSubordinateFace):len()
+      local dCoeff = max( ( vtNMainFace ^ vtNSubordinateFace):len(), 0.5)
       dOffsetParallel = dOffsetParallel * dCoeff
       dOffsetOrthogonal = dOffsetOrthogonal * dCoeff
    end

LuaLibs/FaceData.lua

@@ -91,7 +91,9 @@ function FaceData.GetFacesByAdjacencyNumber( Proc)
       FacesByAdjacencyNumber[i] = {}
    end
    for i = 1, Proc.nFct do
-      table.insert( FacesByAdjacencyNumber[#Proc.Faces[i].Adjacencies], Proc.Faces[i])
+      if #Proc.Faces[i].Adjacencies > 0 then
+         table.insert( FacesByAdjacencyNumber[#Proc.Faces[i].Adjacencies], Proc.Faces[i])
+      end
    end
 
    return FacesByAdjacencyNumber
@@ -114,14 +116,8 @@ function FaceData.GetEdgesInfo( ProcOrId, idFace )
    local nFaceType, EdgesEgt = EgtSurfTmGetFacetOutlineInfo( Proc.id, idFace, GDB_ID.ROOT)
 
    for i = 1, #EdgesEgt do
-      local nPreviousEdgeIndex = i - 1
-      if i == 1 then
-         nPreviousEdgeIndex = #EdgesEgt
-      end
-      local nNextEdgeIndex = i + 1
-      if i == #EdgesEgt then
-         nNextEdgeIndex = 1
-      end
+
+      local nPreviousEdgeIndex, nNextEdgeIndex = BeamLib.GetAdjacentIndices( i, #EdgesEgt)
 
       -- l'elevazione si tiene sempre positiva e la normale sempre diretta verso l'interno della faccia
       -- per sapere se il lato è aperto c'è la proprietà apposita bIsOpen
@@ -141,6 +137,8 @@ function FaceData.GetEdgesInfo( ProcOrId, idFace )
       CurrentEdge.vtEdge = CurrentEdge.ptEnd - CurrentEdge.ptStart ; CurrentEdge.vtEdge:normalize()
       CurrentEdge.sType = 'Standard'
       CurrentEdge.id = i - 1
+      CurrentEdge.nPreviousEdgeIndex = nPreviousEdgeIndex
+      CurrentEdge.nNextEdgeIndex = nNextEdgeIndex
 
       -- se nella Proc ci sono le adiacenze e il lato ha adiacenza, si salva l'angolo con la faccia adiacente
       if Proc.AdjacencyMatrix then
@@ -186,7 +184,7 @@ function FaceData.GetFacesInfo( Proc, Part, FacesToGet)
       Faces[i].id = i - 1
       Faces[i].idTrimesh = Proc.id
       Faces[i].ptCenter, Faces[i].vtN =  EgtSurfTmFacetCenter( Proc.id, i - 1, GDB_ID.ROOT)
-      if Proc.nFct < 6  or FaceIsToGet( i) then
+      if Proc.nFct < 7  or FaceIsToGet( i) then
          -- frame OCS faccia
          Faces[i].frFrameHV = Frame3d( Faces[i].ptCenter, Faces[i].vtN)
          -- elevazione calcolata rispetto al box della parte
@@ -367,7 +365,8 @@ local function GetBottomFaces( Proc)
 
    if Proc.Topology.sFamily == 'Tunnel' then
       return nil
-   elseif not ( Proc.Topology.sFamily == 'Rabbet'
+   elseif not ( Proc.Topology.sFamily == 'PseudoPocket'
+                or Proc.Topology.sFamily == 'Rabbet'
                 or Proc.Topology.sFamily == 'VGroove'
                 or Proc.Topology.sFamily == 'Groove'
                 or Proc.Topology.sFamily == 'Pocket'
@@ -383,10 +382,28 @@ local function GetBottomFaces( Proc)
       return { Proc.Faces[1]}
    end
 
-   -- la faccia di fondo ha sempre Fct - 1 adiacenze
+   -- la faccia di fondo ha sempre Fct - 1 adiacenze, tranne caso speciale DoubleBevel con facce di chiusura triangolari
    local FacesByAdjacencyNumber = FaceData.GetFacesByAdjacencyNumber( Proc)
    if FacesByAdjacencyNumber then
       BottomFaces = FacesByAdjacencyNumber[ Proc.nFct - 1]
+      -- caso speciale DoubleBevel
+      if #BottomFaces == 0 then
+         if Proc.nParts == 1 then
+            BottomFaces = FacesByAdjacencyNumber[ Proc.nFct / 2]
+         -- DoubleBevel composto da più parti
+         else
+            for i = #FacesByAdjacencyNumber, 1, -1 do
+               if #FacesByAdjacencyNumber[i] > 0 then
+                  BottomFaces = FacesByAdjacencyNumber[i]
+                  break
+               end
+            end
+            -- se non sono state trovate facce di fondo significa che nessuna faccia ha adiacenze -> DoubleBevel-2
+            if #BottomFaces == 0 then
+               BottomFaces = Proc.Faces
+            end
+         end
+      end
       -- si rimuovono le facce non adatte ad essere lavorate
       local nBottomFaces = #BottomFaces
       local nCurrentFace = 1
@@ -430,14 +447,7 @@ local function GetBottomFaces( Proc)
    end
 
    for i = 1, #BottomFaces[1].Edges do
-      local nPreviousEdgeIndex = i - 1
-      if i == 1 then
-         nPreviousEdgeIndex = #BottomFaces[1].Edges
-      end
-      local nNextEdgeIndex = i + 1
-      if i == #BottomFaces[1].Edges then
-         nNextEdgeIndex = 1
-      end
+      local nPreviousEdgeIndex, nNextEdgeIndex = BeamLib.GetAdjacentIndices( i, #BottomFaces[1].Edges)
 
       local CurrentEdge = {}
       CurrentEdge.idAdjacentFace = BottomFaces[1].Edges[i].idAdjacentFace
@@ -451,6 +461,8 @@ local function GetBottomFaces( Proc)
       CurrentEdge.ptEnd = BottomFaces[1].Edges[i].ptEnd
       CurrentEdge.vtEdge = BottomFaces[1].Edges[i].vtEdge
       CurrentEdge.id = BottomFaces[1].Edges[i].id
+      CurrentEdge.nPreviousEdgeIndex = BottomFaces[1].Edges[i].nPreviousEdgeIndex
+      CurrentEdge.nNextEdgeIndex = BottomFaces[1].Edges[i].nNextEdgeIndex
 
       if nFirstLongEdgeIndex then
          if i == nFirstLongEdgeIndex then
@@ -476,7 +488,7 @@ end
 local function GetLongFaces( Proc, MainFaces)
    local LongFaces = {}
 
-   if Proc.nFct > 5 then
+   if Proc.nFct > 6 then
       error( 'GetLongFaces : Topology not implemented')
    elseif Proc.nFct == 1 then
       return {}
@@ -519,8 +531,8 @@ local function GetLongFaces( Proc, MainFaces)
    for i = 1, #LongFaces do
       LongFaces[i].sType = 'Long'
 
-      -- calcolo MainEdges possibile solo se 4 lati esatti
-      if #LongFaces[i].Edges ~= 4 then
+      -- calcolo MainEdges possibile solo se 4 lati esatti e caso speciale lato opposto groove tagliato
+      if #LongFaces[i].Edges ~= 4 and not ( #LongFaces[i].Edges == 5 and Proc.Topology.sName == 'Groove-3-Through') then
          break
       end
 
@@ -529,14 +541,7 @@ local function GetLongFaces( Proc, MainFaces)
       LongFaces[i].MainEdges.OppositeEdges = {}
 
       for j = 1, #LongFaces[i].Edges do
-         local nPreviousEdgeIndex = j - 1
-         if j == 1 then
-            nPreviousEdgeIndex = #LongFaces[1].Edges
-         end
-         local nNextEdgeIndex = j + 1
-         if j == #LongFaces[i].Edges then
-            nNextEdgeIndex = 1
-         end
+         local nPreviousEdgeIndex, nNextEdgeIndex = BeamLib.GetAdjacentIndices( j, #LongFaces[i].Edges)
 
          local CurrentEdge = {}
          CurrentEdge.idAdjacentFace = LongFaces[i].Edges[j].idAdjacentFace
@@ -550,6 +555,8 @@ local function GetLongFaces( Proc, MainFaces)
          CurrentEdge.ptEnd = LongFaces[i].Edges[j].ptEnd
          CurrentEdge.vtEdge = LongFaces[i].Edges[j].vtEdge
          CurrentEdge.id = LongFaces[i].Edges[j].id
+         CurrentEdge.nPreviousEdgeIndex = LongFaces[i].Edges[j].nPreviousEdgeIndex
+         CurrentEdge.nNextEdgeIndex = LongFaces[i].Edges[j].nNextEdgeIndex
 
          if Proc.Topology.sFamily == 'Tunnel' then
             if CurrentEdge.idAdjacentFace > -1 then
@@ -575,6 +582,12 @@ local function GetLongFaces( Proc, MainFaces)
             end
          end
       end
+      -- il primo OppositeEdge deve essere sempre il più lungo, se più di uno
+      if #LongFaces[i].MainEdges.OppositeEdges > 1 then
+         if LongFaces[i].MainEdges.OppositeEdges[1].dLength < LongFaces[i].MainEdges.OppositeEdges[2].dLength - 10 * GEO.EPS_SMALL then
+            LongFaces[i].MainEdges.OppositeEdges[1], LongFaces[i].MainEdges.OppositeEdges[2] = LongFaces[i].MainEdges.OppositeEdges[2], LongFaces[i].MainEdges.OppositeEdges[1]
+         end
+      end
    end
 
    return LongFaces
@@ -584,7 +597,7 @@ end
 local function GetSideFaces( Proc, MainFaces)
    local SideFaces = {}
 
-   if Proc.nFct > 5 then
+   if Proc.nFct > 6 then
       error( 'GetSideFaces : Topology not implemented')
    elseif Proc.nFct == 1 then
       return {}
@@ -629,14 +642,7 @@ local function GetSideFaces( Proc, MainFaces)
       SideFaces[i].MainEdges.OppositeEdges = {}
 
       for j = 1, #SideFaces[i].Edges do
-         local nPreviousEdgeIndex = j - 1
-         if j == 1 then
-            nPreviousEdgeIndex = #SideFaces[1].Edges
-         end
-         local nNextEdgeIndex = j + 1
-         if j == #SideFaces[i].Edges then
-            nNextEdgeIndex = 1
-         end
+         local nPreviousEdgeIndex, nNextEdgeIndex = BeamLib.GetAdjacentIndices( j, #SideFaces[i].Edges)
 
          local CurrentEdge = {}
          CurrentEdge.idAdjacentFace = SideFaces[i].Edges[j].idAdjacentFace
@@ -650,6 +656,8 @@ local function GetSideFaces( Proc, MainFaces)
          CurrentEdge.ptEnd = SideFaces[i].Edges[j].ptEnd
          CurrentEdge.vtEdge = SideFaces[i].Edges[j].vtEdge
          CurrentEdge.id = SideFaces[i].Edges[j].id
+         CurrentEdge.nPreviousEdgeIndex = SideFaces[i].Edges[j].nPreviousEdgeIndex
+         CurrentEdge.nNextEdgeIndex = SideFaces[i].Edges[j].nNextEdgeIndex
 
          if Proc.Topology.sFamily == 'Tunnel' then
             if CurrentEdge.idAdjacentFace > -1 then
@@ -686,19 +694,25 @@ function FaceData.GetMainFaces( Proc, Part)
    local MainFaces = {}
 
    -- CASO 1 : Feature tipo LapJoint
-   if Proc.Topology.sFamily == 'Rabbet' or Proc.Topology.sFamily == 'VGroove' or Proc.Topology.sFamily == 'Groove' or
+   if Proc.Topology.sFamily == 'PseudoPocket' or Proc.Topology.sFamily == 'Rabbet' or Proc.Topology.sFamily == 'VGroove' or Proc.Topology.sFamily == 'Groove' or
       Proc.Topology.sFamily == 'Pocket' or Proc.Topology.sFamily == 'Tunnel' or Proc.Topology.sFamily == 'Bevel' or
       Proc.Topology.sFamily == 'DoubleBevel' or Proc.Topology.sFamily == 'Cut' or Proc.Topology.sFamily == 'HeadCut' or Proc.Topology.sFamily == 'TailCut' then
       
-      if ( Proc.Topology.bIsThrough and Proc.Topology.bAllRightAngles and Proc.nFct < 5)
-         or ( Proc.nFct == 1) or Proc.Topology.sName == 'Bevel-2-Blind' then
+      if Proc.nParts == 1 and ( ( Proc.Topology.bIsThrough and Proc.Topology.bAllRightAngles and Proc.nFct < 5)
+         or ( Proc.nFct == 1) or Proc.Topology.sName == 'Bevel-2-Blind') then
 
          MainFaces.TunnelAddedFaces = GetTunnelFaces( Proc, Part)
       end
 
       MainFaces.BottomFaces = GetBottomFaces( Proc)
-      MainFaces.LongFaces = GetLongFaces( Proc, MainFaces)
-      MainFaces.SideFaces = GetSideFaces( Proc, MainFaces)
+      if Proc.nParts == 1 then
+         MainFaces.LongFaces = GetLongFaces( Proc, MainFaces)
+         MainFaces.SideFaces = GetSideFaces( Proc, MainFaces)
+      -- caso tipo DoubleBevel con facce separate
+      else
+         MainFaces.LongFaces = {}
+         MainFaces.SideFaces = {}
+      end
 
    else
       MainFaces = nil

LuaLibs/FeatureLib.lua

@@ -43,7 +43,7 @@ end
 
 -------------------------------------------------------------------------------------------------------------
 -- restituisce vero se la feature con box b3Proc taglia l'intera sezione della barra
-local function IsFeatureCuttingEntireSection( b3Proc, Part)
+function FeatureLib.IsFeatureCuttingEntireSection( b3Proc, Part)
    return ( b3Proc:getDimY() > ( Part.b3Part:getDimY() - 500 * GEO.EPS_SMALL)  and  b3Proc:getDimZ() > ( Part.b3Part:getDimZ() - 500 * GEO.EPS_SMALL))
 end
 
@@ -198,7 +198,7 @@ function FeatureLib.ClassifyTopology( Proc, Part)
 
    if not Proc.AffectedFaces then Proc.AffectedFaces = BeamLib.GetAffectedFaces( Proc, Part) end
 
-   local bIsFeatureCuttingEntireSection = IsFeatureCuttingEntireSection( Proc.b3Box, Part)
+   local bIsFeatureCuttingEntireSection = FeatureLib.IsFeatureCuttingEntireSection( Proc.b3Box, Part)
    local bIsFeatureCuttingEntireLength = IsFeatureCuttingEntireLength( Proc.b3Box, Part)
    local bIsAnyDimensionLongAsPart = IsAnyDimensionLongAsPart( Proc, Part)
    local vAdj = Proc.AdjacencyMatrix
@@ -226,13 +226,13 @@ function FeatureLib.ClassifyTopology( Proc, Part)
    elseif Proc.nFct == 2 and bAllAnglesConcave and #vTriangularFaces == 1 then
       sFamily = 'Bevel'
       bIsThrough = false
-   elseif Proc.nFct == 2 and bAllAnglesConcave and ( Proc.AffectedFaces.bLeft or Proc.AffectedFaces.bRight) and ( Proc.AffectedFaces.bFront or Proc.AffectedFaces.bBack) then
+   elseif Proc.nFct == 2 and bAllAnglesConcave and Proc.nParts == 1 and ( Proc.AffectedFaces.bLeft or Proc.AffectedFaces.bRight) and ( Proc.AffectedFaces.bFront or Proc.AffectedFaces.bBack) then
       sFamily = 'Rabbet'
       bIsThrough = true
-   elseif Proc.nFct == 2 and bAllAnglesConcave then
+   elseif Proc.nFct == 2 and bAllAnglesConcave and Proc.nParts == 1 then
       sFamily = 'VGroove'
       bIsThrough = true
-   elseif Proc.nFct == 2 and not bAllAnglesConcave and bIsAnyDimensionLongAsPart then
+   elseif Proc.nFct == 2 and ( not bAllAnglesConcave or Proc.nParts == 2) and bIsAnyDimensionLongAsPart then
       sFamily = 'DoubleBevel'
       bIsThrough = true
    elseif Proc.nFct == 3 and bAllAnglesConcave and #vFacesByAdjNumber[2] == 1 and #vTriangularFaces == 2 then
@@ -244,7 +244,9 @@ function FeatureLib.ClassifyTopology( Proc, Part)
    elseif Proc.nFct == 3 and bAllAnglesConcave and #vFacesByAdjNumber[2] == 3 then
       sFamily = 'Groove'
       bIsThrough = false
-   elseif Proc.nFct == 4 and #vFacesByAdjNumber[2] == 4  and #vTriangularFaces == 2 then
+   elseif Proc.nFct == 4
+          and ( ( not bAllAnglesConcave and ( ( #vFacesByAdjNumber[2] == 2 and #vTriangularFaces == 2) or ( #vFacesByAdjNumber[3] == 2)))
+          or ( #vTriangularFaces == 2 and Proc.nParts == 2))  then
       sFamily = 'DoubleBevel'
       bIsThrough = false
    elseif Proc.nFct == 4 and bAllAnglesConcave and #vFacesByAdjNumber[3] == 2 then
@@ -253,13 +255,18 @@ function FeatureLib.ClassifyTopology( Proc, Part)
    elseif Proc.nFct == 4 and bAllAnglesConcave and #vFacesByAdjNumber[2] == 4 and bIsAnyDimensionLongAsPart then
       sFamily = 'Tunnel'
       bIsThrough = true
+   elseif Proc.nFct == 4 and bAllAnglesConcave and #vFacesByAdjNumber[3] == 1 then
+      sFamily = 'PseudoPocket'
+      bIsThrough = false
    elseif Proc.nFct >= 4 and #vFacesByAdjNumber[1] == 2 and bIsAnyDimensionLongAsPart then
       sFamily = 'Strip'
       bIsThrough = true
    elseif Proc.nFct == 5 and bAllAnglesConcave and #vFacesByAdjNumber[4] == 1 then
       sFamily = 'Pocket'
       bIsThrough = false
-   elseif Proc.nFct == 6 and #vFacesByAdjNumber[2] == 4 and #vFacesByAdjNumber[3] == 2 and #vTriangularFaces == 4 then
+   elseif Proc.nFct == 6
+          and ( ( #vFacesByAdjNumber[1] == 4 and #vFacesByAdjNumber[3] == 2 and #vTriangularFaces == 4 and not bAllAnglesConcave)
+          or ( #vFacesByAdjNumber[1] == 4 and #vTriangularFaces == 4 and Proc.nParts == 2)) then
       sFamily = 'DoubleBevel'
       bIsThrough = false
    end
@@ -333,6 +340,9 @@ function FeatureLib.GetAdditionalInfo( Proc, Part)
       Proc.AdjacencyMatrix = FaceData.GetAdjacencyMatrix( Proc)
       Proc.Faces = FaceData.GetFacesInfo( Proc, Part)
       Proc.FeatureInfo, Proc.MainFaces = FeatureLib.GetRafterNotchData( Proc)
+   elseif ( ID.IsScarfJoint( Proc) or ID.IsScarfSimple( Proc)) then
+      Proc.AdjacencyMatrix = FaceData.GetAdjacencyMatrix( Proc)
+      Proc.Faces = FaceData.GetFacesInfo( Proc, Part)
    end
 
    return Proc
@@ -757,6 +767,9 @@ function FeatureLib.CalculateStrategiesCompositeRating( AvailableStrategies, sMa
 
          AvailableStrategies[n].Result.dCompositeRating = dQuality + dCompletion + dTime   -- TODO da verificare se meglio sommare o moltiplicare gli indici
       else
+         if not AvailableStrategies[n].Result then
+            AvailableStrategies[n].Result = {}
+         end
          AvailableStrategies[n].Result.dCompositeRating = 0
       end
    end
@@ -850,7 +863,7 @@ function FeatureLib.GetFeatureSplittingPoints( Proc, Part, OptionalParameters)
          if Part.dRestLength + Part.b3Part:getDimX() < BeamData.dMinRaw * 1.5 then
             dSplitXLeft = Part.b3Part:getMax():getX() - ( ( Part.dRestLength + Part.b3Part:getDimX()) / 2)
          else
-            dSplitXLeft = max( Proc.b3Box:getMin():getX() + ( BeamData.dMinRaw)/2 + 150, Part.b3Part:getMax():getX() - dMaxSegmentLengthOnEdges)
+            dSplitXLeft = max( Proc.b3Box:getMin():getX() + ( BeamData.dMinRaw) / 2 + 150, Part.b3Part:getMax():getX() - dMaxSegmentLengthOnEdges)
          end
       end
       dFeatureCentralLength = abs( dSplitXRight - dSplitXLeft)

LuaLibs/MachiningLib.lua

@@ -169,20 +169,20 @@ function MachiningLib.GetSplitMachinings( Machinings, SplittingPoints, Part)
                   dStartAddLength, dEndAddLength = dEndAddLength, dStartAddLength
                end
                if j == 1 then
-                  dEndAddLength = - ( SplittingPoints[j]:getX() - dEdgeMinX) + BeamData.MILL_OVERLAP
+                  dEndAddLength = - ( SplittingPoints[j]:getX() - dEdgeMinX) + BeamData.MILL_OVERLAP / 2
                   if LeadOutForSplit then
                      Machinings[nCurrentMachiningIndex].LeadOut = BeamLib.TableCopyDeep( LeadOutForSplit)
                   end
                   Machinings[nCurrentMachiningIndex].ptCenter = Point3d( SplittingPoints[j]:getX() + ( dEdgeMaxX - SplittingPoints[j]:getX()) / 2, 0, 0)
                elseif j == nParts then
-                  dStartAddLength = - ( dEdgeMaxX - SplittingPoints[j - 1]:getX()) + BeamData.MILL_OVERLAP
+                  dStartAddLength = - ( dEdgeMaxX - SplittingPoints[j - 1]:getX()) + BeamData.MILL_OVERLAP / 2
                   if LeadInForSplit then
                      Machinings[nCurrentMachiningIndex].LeadIn = BeamLib.TableCopyDeep( LeadInForSplit)
                   end
                   Machinings[nCurrentMachiningIndex].ptCenter = Point3d( dEdgeMinX + ( SplittingPoints[j - 1]:getX() - dEdgeMinX) / 2, 0, 0)
                else
-                  dStartAddLength = - ( dEdgeMaxX - SplittingPoints[j - 1]:getX()) + BeamData.MILL_OVERLAP
-                  dEndAddLength = - ( SplittingPoints[j]:getX() - dEdgeMinX) + BeamData.MILL_OVERLAP
+                  dStartAddLength = - ( dEdgeMaxX - SplittingPoints[j - 1]:getX()) + BeamData.MILL_OVERLAP / 2
+                  dEndAddLength = - ( SplittingPoints[j]:getX() - dEdgeMinX) + BeamData.MILL_OVERLAP / 2
                   if LeadInForSplit then
                      Machinings[nCurrentMachiningIndex].LeadIn = BeamLib.TableCopyDeep( LeadInForSplit)
                   end
@@ -347,7 +347,7 @@ local function TestEngagement( sBladeEngagement, Parameters, OptionalParameters)
       return false
    end
    -- lavorazione in collisione con il pezzo: non fattibile
-   local bCollisionFound, bMoveAfterSplit = PreSimulationLib.CheckCollision( sBladeEngagement, CheckCollisionParameters, CheckCollisionOptionalParameters)
+   local bCollisionFound, bMoveAfterSplit = PreSimulationLib.CheckCollision( CheckCollisionParameters, CheckCollisionOptionalParameters)
    if bCollisionFound then
       return false
    end
@@ -363,16 +363,22 @@ local function TestEngagement( sBladeEngagement, Parameters, OptionalParameters)
    -- attacco perpendicolare
    local PerpendicularLeadInOut = LeadInOutLib.CalculateLeadInOut( 'Perpendicular', Parameters, LeadInOutOptionalParameters)
    -- check extracorsa nei punti di attacco
-
    PointsOnToolTipCenter = {
       PreSimulationLib.GetPointOnToolTipCenter( PerpendicularLeadInOut.LeadIn.ptPoint, vtHead, Face.vtN, Edge.vtN, Tool),
       PreSimulationLib.GetPointOnToolTipCenter( PerpendicularLeadInOut.LeadOut.ptPoint, vtHead, Face.vtN, Edge.vtN, Tool)
    }
    local bOutOfStrokePerpendicular = PreSimulationLib.CheckOutOfStrokeFromPoints( PointsOnToolTipCenter, vtHead, nSCC, Tool)
-   -- se non è in extracorsa si aggiunge come attacco possibile
+   -- attacco perpendicolare non in extracorsa: si verifica se è in collisione
    if not bOutOfStrokePerpendicular then
-      LeadInOut.Perpendicular = PerpendicularLeadInOut
-      LeadInOut.Perpendicular.bMoveAfterSplit = bMoveAfterSplit
+      CheckCollisionOptionalParameters.PointsToCheck = {}
+      table.insert( CheckCollisionOptionalParameters.PointsToCheck, PerpendicularLeadInOut.LeadIn.ptPoint)
+      table.insert( CheckCollisionOptionalParameters.PointsToCheck, PerpendicularLeadInOut.LeadOut.ptPoint)
+      local bCollisionFoundPerpendicular, bMoveAfterSplitPerpendicular = PreSimulationLib.CheckCollision( CheckCollisionParameters, CheckCollisionOptionalParameters)
+      -- attacco perpendicolare possibile
+      if not bCollisionFoundPerpendicular then
+         LeadInOut.Perpendicular = PerpendicularLeadInOut
+         LeadInOut.Perpendicular.bMoveAfterSplit = bMoveAfterSplitPerpendicular
+      end
    end
    -- se c'è almeno un lato chiuso l'unico attacco possibile è il perpendicolare
    if not ( Edge.bIsStartOpen and Edge.bIsEndOpen) then
@@ -397,7 +403,7 @@ local function TestEngagement( sBladeEngagement, Parameters, OptionalParameters)
       CheckCollisionOptionalParameters.PointsToCheck = {}
       table.insert( CheckCollisionOptionalParameters.PointsToCheck, TangentLeadInOut.LeadIn.ptPoint)
       table.insert( CheckCollisionOptionalParameters.PointsToCheck, TangentLeadInOut.LeadOut.ptPoint)
-      local bCollisionFoundTangent, bMoveAfterSplitTangent = PreSimulationLib.CheckCollision( sBladeEngagement, CheckCollisionParameters, CheckCollisionOptionalParameters)
+      local bCollisionFoundTangent, bMoveAfterSplitTangent = PreSimulationLib.CheckCollision( CheckCollisionParameters, CheckCollisionOptionalParameters)
       -- attacco tangenziale possibile
       if not bCollisionFoundTangent then
          LeadInOut.Tangent = TangentLeadInOut
@@ -468,6 +474,11 @@ end
 function MachiningLib.FindMill( Proc, ToolSearchParameters)
    local ToolInfo = {}
 
+   -- direzione utensile e fipo fresa obbligatori, altrimenti si esce
+   if not ToolSearchParameters.vtToolDirection or not ToolSearchParameters.sMillShape then
+      return ToolInfo
+   end
+
    local nBestToolIndex
    local dBestToolResidualDepth = 0
    for i = 1, #TOOLS do
@@ -511,6 +522,18 @@ function MachiningLib.FindMill( Proc, ToolSearchParameters)
             bIsToolCompatible = false
          end
       end
+      
+      -- TODO da sostituire con test collisione come lama
+      local bIsFromBottom = ToolSearchParameters.vtToolDirection:getZ() < - 10 * GEO.EPS_SMALL
+      local bIsFromTop = ToolSearchParameters.vtToolDirection:getZ() > 10 * GEO.EPS_SMALL
+      local bIsSlanted = abs( ToolSearchParameters.vtToolDirection:getY()) > 0.707
+      local bIsOnHeadOrTail = Proc.AffectedFaces.bLeft or Proc.AffectedFaces.bRight
+      if ( ( bIsFromBottom and TOOLS[i].SetupInfo.HeadType.bTop) or ( bIsFromTop and TOOLS[i].SetupInfo.HeadType.bBottom))
+         and ( not bIsSlanted)
+         and ( not bIsOnHeadOrTail) then
+
+         bIsToolCompatible = false
+      end
 
       -- scelgo il migliore
       if bIsToolCompatible then
@@ -579,13 +602,11 @@ end
 -------------------------------------------------------------------------------------------------------------
 -- funzione per cercare utensile tipo LAMA con certe caratteristiche
 -- TODO da rivedere/completare
+-- TODO per Engagement serviranno (opzionali) sBlockedAxis e vtAux
 function MachiningLib.FindBlade( Proc, ToolSearchParameters)
    local ToolInfo = {}
 
    -- parametri obbligatori
-   if type( ToolSearchParameters.FaceToMachine) ~= 'table' then
-      error( 'FindBlade : missing face info')
-   end
    if type( ToolSearchParameters.bAllowTopHead) ~= 'boolean' then
       error( 'FindBlade : missing top head info')
    end
@@ -604,9 +625,10 @@ function MachiningLib.FindBlade( Proc, ToolSearchParameters)
    local bForceLongcutBlade = ToolSearchParameters.bForceLongcutBlade or false
    local EdgeToMachine = ToolSearchParameters.EdgeToMachine
    local Part = ToolSearchParameters.Part
-   local bIsDicing = ToolSearchParameters.bIsDicing or false
+   local idCheckCollisionTm = ToolSearchParameters.idCheckCollisionTm
    local sRestLengthSideForPreSimulation = ToolSearchParameters.sRestLengthSideForPreSimulation or 'Tail'
    local bCannotSplitRestLength = ToolSearchParameters.bCannotSplitRestLength or false
+   local bDisableRealElevationCheck = ToolSearchParameters.bDisableRealElevationCheck or false
 
    local nBestToolIndex
    local dBestToolResidualDepth = 0
@@ -638,9 +660,10 @@ function MachiningLib.FindBlade( Proc, ToolSearchParameters)
                dDepthToMachine = min( dElevation, TOOLS[i].dMaxDepth)
             }
             local BladeEngagementOptionalParameters = {
-               bIsDicing = bIsDicing,
+               idCheckCollisionTm = idCheckCollisionTm,
                sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
-               bCannotSplitRestLength = bCannotSplitRestLength
+               bCannotSplitRestLength = bCannotSplitRestLength,
+               bDisableRealElevationCheck = bDisableRealElevationCheck
             }
             TIMER:startElapsed( 'GetBladeEngagement')
             bIsBladeOk, CurrentEngagement = MachiningLib.GetBladeEngagement( BladeEngagementParameters, BladeEngagementOptionalParameters)
@@ -649,12 +672,6 @@ function MachiningLib.FindBlade( Proc, ToolSearchParameters)
             if not bIsBladeOk then
                bIsToolCompatible = false
             end
-
-         -- se si ha solo la faccia si può verificare se questa è orientata correttamente
-         elseif FaceToMachine then
-            if MachiningLib.IsFaceZOutOfRange( FaceToMachine.vtN, TOOLS[i]) then
-               bIsToolCompatible = false
-            end
          end
       end
 
@@ -1158,7 +1175,7 @@ end
 
 -------------------------------------------------------------------------------------------------------------
 -- funzione per aggiungere una nuova lavorazione
-function MachiningLib.AddOperations( MACHININGS, Part, sRotation)
+function MachiningLib.AddOperations( MACHININGS, PARTS, Part, sRotation)
    local nErr
    local sErr = ''
    local bAreAllMachiningApplyOk = true
@@ -1355,13 +1372,19 @@ function MachiningLib.AddOperations( MACHININGS, Part, sRotation)
                                        MachStartAxesPos = EgtGetMachiningStartAxes(),
                                        MachEndAxesPos = EgtGetMachiningEndAxes()}
                table.insert( DB_MACH_APPLIED, MachExtraInfo)
+               
+               -- se non esistono punto iniziale o finale, si disattiva operazione
+               if not MachExtraInfo.MachStartAxesPos or not MachExtraInfo.MachEndAxesPos then
+                  EgtSetOperationMode( nOperationId, false)
+               end
 
                -- se errore in applicazione
                if not bIsApplyOk then
                   bAreAllMachiningApplyOk = false
                   nErr, sErr = EgtGetLastMachMgrError()
                   EgtSetOperationMode( nOperationId, false)
-                  local CurrProc = PROCESSINGS[MACHININGS[i].Proc.nIndexPartInParts].Rotation[MACHININGS[i].Proc.nIndexRotation][MACHININGS[i].Proc.nIndexInVProc]
+                  local nOffsetIndex = EgtIf( Part.bPartInCombiIsInverted, 4, 0)
+                  local CurrProc = PROCESSINGS[MACHININGS[i].Proc.nIndexPartInParts].Rotation[MACHININGS[i].Proc.nIndexRotation+nOffsetIndex][MACHININGS[i].Proc.nIndexInVProc]
                   -- si annulla la feature scelta, in modo che un successivo ricalcolo non la tenga in considerazione
                   CurrProc.AvailableStrategies[CurrProc.nIndexBestStrategy].Result.sStatus = 'Not-Applicable'
                   CurrProc.AvailableStrategies[CurrProc.nIndexBestStrategy].Result.sInfo = 'REJECTED (' .. sErr .. ')'
@@ -1378,7 +1401,7 @@ function MachiningLib.AddOperations( MACHININGS, Part, sRotation)
                -- se applicazione andata a buon fine
                else
 
-                  -- se non deve essere igniorato, si salva ingombro lavorazione attuale e fasi successive
+                  -- se non deve essere ignorato, si salva ingombro lavorazione attuale e fasi successive
                   if not MACHININGS[i].AuxiliaryData.bIgnoreNotClampableLength then
                      -- salvo ingombro non pinzabile testa/coda
                      local nCurrRotation = MACHININGS[i].Proc.nIndexRotation
@@ -1420,7 +1443,7 @@ function MachiningLib.AddOperations( MACHININGS, Part, sRotation)
                   bSplitExecuted = true
                   MACHININGS.Info.bSplitExecuted = true
 
-                  BeamLib.AddPhaseWithRawParts( Part.idRaw, BeamData.ptOriXR, BeamData.dPosXR, BeamData.RAW_OFFSET)
+                  BeamLib.AddPhaseWithRawParts( PARTS, Part.nIndexInParts, BeamData.ptOriXR, BeamData.dPosXR, BeamData.RAW_OFFSET)
                   -- se grezzo successivo senza pezzi e finale, va tolto
                   local nNextRawId = EgtGetNextRawPart( Part.idRaw)
                   if nNextRawId  and  EgtGetPartInRawPartCount( nNextRawId) == 0  and  EgtGetRawPartBBox( nNextRawId):getDimX() < BeamData.dMinRaw then
@@ -1436,18 +1459,20 @@ function MachiningLib.AddOperations( MACHININGS, Part, sRotation)
                   local nPhase = EgtGetCurrPhase()
                   local idDisp = EgtGetPhaseDisposition( nPhase)
 
+                  -- posizione iniziale considerando eventuiali prerotazioni
+                  local nRealInitialPosition = Part.nInitialPosition
                   if sRotation == 'DOWN' then
-                     local nRotation = EgtIf( Part.nInitialPosition + 2 > 4, Part.nInitialPosition + 2 - 4, Part.nInitialPosition + 2) - 1
+                     local nRotation = EgtIf( nRealInitialPosition + 2 > 4, nRealInitialPosition + 2 - 4, nRealInitialPosition + 2) - 1
                      BeamLib.RotateRawPart( Part, nRotation)
                      EgtSetInfo( idDisp, 'ROT', -2)
                      EgtSetInfo( idDisp, 'TYPE', 'MID2')
                   elseif sRotation == 'SIDE' then
-                     local nRotation = EgtIf( Part.nInitialPosition + 1 > 4, Part.nInitialPosition + 1 - 4, Part.nInitialPosition + 1) - 1
+                     local nRotation = EgtIf( nRealInitialPosition + 1 > 4, nRealInitialPosition + 1 - 4, nRealInitialPosition + 1) - 1
                      BeamLib.RotateRawPart( Part, nRotation)
                      EgtSetInfo( idDisp, 'ROT', -1)
                      EgtSetInfo( idDisp, 'TYPE', 'MID2')
                   else
-                     local nRotation = Part.nInitialPosition - 1
+                     local nRotation = nRealInitialPosition - 1
                      BeamLib.RotateRawPart( Part, nRotation)
                      EgtSetInfo( idDisp, 'TYPE', 'END')
                   end
@@ -1516,14 +1541,14 @@ function MachiningLib.GetTimeToMachineAllStepsWithLeadInOut( Machining, Part)
    if Machining.nType == MCH_MY.DRILLING then
       local function fact(n) return n == 0 and 1 or n * fact(n - 1) end
       local nSteps = ceil( Machining.sDepth / Machining.dStep)
-      local dLenghtEachStep = Machining.sDepth / nSteps
+      local dLengthEachStep = Machining.sDepth / nSteps
       -- numero dei movimenti a step, compresi andata e ritorno per scarico truciolo
       local nTotStepMovement = 2 * fact( nSteps)
       -- in feed si lavorano solo gli step
-      local dFeedTime = ( ( dLenghtEachStep + Machining.dStartSafetyLength) * nSteps) / dToolFeed
-      -- ritorno per scaricare e approccio al prossimo step seno in feed finale
-      local dEndFeedTime = ( dLenghtEachStep * ( nTotStepMovement - nSteps) + EgtMdbGetGeneralParam( MCH_GP.SAFEZ) * 2) / dToolEndFeed
-      dLengthToMachineAllStepsWithLeadInOut = dLenghtEachStep * nTotStepMovement
+      local dFeedTime = ( ( dLengthEachStep + Machining.dStartSafetyLength) * nSteps) / dToolFeed
+      -- ritorno per scaricare e approccio al prossimo step sono in feed finale
+      local dEndFeedTime = ( dLengthEachStep * ( nTotStepMovement - nSteps) + EgtMdbGetGeneralParam( MCH_GP.SAFEZ) * 2) / dToolEndFeed
+      dLengthToMachineAllStepsWithLeadInOut = dLengthEachStep * nTotStepMovement
       dTimeToMachineTotal = dFeedTime + dEndFeedTime
    elseif Machining.nType == MCH_MY.MILLING then
       -- stima LeadIn e LeadOut; se non settati si impostano a valori di default
@@ -1559,8 +1584,8 @@ function MachiningLib.GetTimeToMachineAllStepsWithLeadInOut( Machining, Part)
          Machining.CloneStepsLongitudinal.nCount = 1
       end
       -- stima tempi di lavorazione per i diversi tratti
-      local dTimeToMachineLeadIn = ( Machining.dDepthToMachine + ( TOOLS[Machining.nToolIndex].SetupInfo.dZSafeDelta or 60) + EgtMdbGetGeneralParam( MCH_GP.SAFEZ)) / dToolStartFeed
-      local dTimeToMachineLeadOut = ( Machining.dDepthToMachine + ( TOOLS[Machining.nToolIndex].SetupInfo.dZSafeDelta or 60) + EgtMdbGetGeneralParam( MCH_GP.SAFEZ)) / dToolEndFeed
+      local dTimeToMachineLeadIn = ( Machining.dDepthToMachine + ( TOOLS[Machining.nToolIndex].SetupInfo.dZSafeDelta or 0) + EgtMdbGetGeneralParam( MCH_GP.SAFEZ)) / dToolStartFeed
+      local dTimeToMachineLeadOut = ( Machining.dDepthToMachine + ( TOOLS[Machining.nToolIndex].SetupInfo.dZSafeDelta or 0) + EgtMdbGetGeneralParam( MCH_GP.SAFEZ)) / dToolEndFeed
       local dTimeToMachineEdge = Machining.dLengthToMachine / dToolFeed
       -- calcolo lunghezze e tempi
       if Machining.Steps.nStepType == MCH_MILL_ST.ZIGZAG then
@@ -1780,44 +1805,46 @@ function MachiningLib.ShortestPathSorting()
 
          -- se è una lavorazione
          while DB_MACH_APPLIED[i] and DB_MACH_APPLIED[i].sType ~= 'DISP' do
-            -- se lavorazione non attiva non va considerata
-            local nOperationId = DB_MACH_APPLIED[i].nOperationId
-            if EgtGetOperationMode( nOperationId) then
-               local ptMinX, ptMaxX
-               -- aggiungo lavorazioni 
-               local nToolIndex = MACHININGS[DB_MACH_APPLIED[i].nIndexInMachinings].Machining.nToolIndex
-               EgtOptMachAddTool( nToolIndex, 2, 2) -- , [ num dTC_X, num dTC_Y, num dTC_Z, num dTC_A, num dTC_B, num dTC_C])
-               -- viene eseguito prima il gruppo con indice più alto, quindi si inverte indice dato che lo stage è dal più piccolo al più grande 
-               local nGroup = 10 - MACHININGS[DB_MACH_APPLIED[i].nIndexInMachinings].Machining.nStage
-               local MachStartAxesPos = DB_MACH_APPLIED[i].MachStartAxesPos
-               local MachEndAxesPos = DB_MACH_APPLIED[i].MachEndAxesPos
-               EgtOptMachAddMachining( i, nToolIndex, nGroup, MachStartAxesPos, MachEndAxesPos)
-               table.insert( MachiningOptList, i)
+            if DB_MACH_APPLIED[i].MachStartAxesPos and DB_MACH_APPLIED[i].MachEndAxesPos then
+               -- se lavorazione non attiva non va considerata
+               local nOperationId = DB_MACH_APPLIED[i].nOperationId
+               if EgtGetOperationMode( nOperationId) then
+                  local ptMinX, ptMaxX
+                  -- aggiungo lavorazioni 
+                  local nToolIndex = MACHININGS[DB_MACH_APPLIED[i].nIndexInMachinings].Machining.nToolIndex
+                  EgtOptMachAddTool( nToolIndex, 2, 2) -- , [ num dTC_X, num dTC_Y, num dTC_Z, num dTC_A, num dTC_B, num dTC_C])
+                  -- viene eseguito prima il gruppo con indice più alto, quindi si inverte indice dato che lo stage è dal più piccolo al più grande 
+                  local nGroup = 10 - MACHININGS[DB_MACH_APPLIED[i].nIndexInMachinings].Machining.nStage
+                  local MachStartAxesPos = DB_MACH_APPLIED[i].MachStartAxesPos
+                  local MachEndAxesPos = DB_MACH_APPLIED[i].MachEndAxesPos
+                  EgtOptMachAddMachining( i, nToolIndex, nGroup, MachStartAxesPos, MachEndAxesPos)
+                  table.insert( MachiningOptList, i)
 
-               -- si salvano i punti minimi e massimi tra tutte le lavorazioni di ogni gruppo
-               if MachStartAxesPos[1] < MachEndAxesPos[1] then
-                  ptMinX = MachStartAxesPos
-                  ptMaxX = MachEndAxesPos
-               else
-                  ptMinX = MachEndAxesPos
-                  ptMaxX = MachStartAxesPos
-               end
-
-               -- si aggiungono le info di gruppo
-               local bFound = false
-               for t = 1, #GroupInfo do
-                  if GroupInfo[t].nGroup == nGroup then
-                     if GroupInfo[t].ptMin[1] > ptMinX[1] then GroupInfo[t].ptMin = ptMinX end
-                     if GroupInfo[t].ptMax[1] < ptMaxX[1] then GroupInfo[t].ptMax = ptMaxX end
-                     bFound = true
+                  -- si salvano i punti minimi e massimi tra tutte le lavorazioni di ogni gruppo
+                  if MachStartAxesPos[1] < MachEndAxesPos[1] then
+                     ptMinX = MachStartAxesPos
+                     ptMaxX = MachEndAxesPos
+                  else
+                     ptMinX = MachEndAxesPos
+                     ptMaxX = MachStartAxesPos
                   end
-               end
-               -- se non ho trovato, si aggiunge in lista
-               if not bFound then
-                  table.insert( GroupInfo, { nGroup = nGroup, nStage = MACHININGS[DB_MACH_APPLIED[i].nIndexInMachinings].Machining.nStage, ptMin = ptMinX, ptMax = ptMaxX})
-               end
 
-               nMachInDisp = nMachInDisp + 1
+                  -- si aggiungono le info di gruppo
+                  local bFound = false
+                  for t = 1, #GroupInfo do
+                     if GroupInfo[t].nGroup == nGroup then
+                        if GroupInfo[t].ptMin[1] > ptMinX[1] then GroupInfo[t].ptMin = ptMinX end
+                        if GroupInfo[t].ptMax[1] < ptMaxX[1] then GroupInfo[t].ptMax = ptMaxX end
+                        bFound = true
+                     end
+                  end
+                  -- se non ho trovato, si aggiunge in lista
+                  if not bFound then
+                     table.insert( GroupInfo, { nGroup = nGroup, nStage = MACHININGS[DB_MACH_APPLIED[i].nIndexInMachinings].Machining.nStage, ptMin = ptMinX, ptMax = ptMaxX})
+                  end
+
+                  nMachInDisp = nMachInDisp + 1
+               end
             end
             i = i + 1
          end

LuaLibs/PreSimulationLib.lua

@@ -34,12 +34,12 @@ local function GetMachineAxes()
 end
 
 -------------------------------------------------------------------------------------------------------------
-local function LogOutstroke( ptOnToolTipCenter, vtHead, OptionalParameters)
+local function LogOutstroke( sToolName, ptOnToolTipCenter, vtHead, OptionalParameters)
 
    -- parametri opzionali
    OptionalParameters = OptionalParameters or {}
-   local LinearAxes = OptionalParameters.LinearAxes
-   local RotativeAxes = OptionalParameters.RotativeAxes
+   local LinearAxesValues = OptionalParameters.LinearAxesValues
+   local RotativeAxesValues = OptionalParameters.RotativeAxesValues
 
    -- gruppo per geometrie temporanee
    local idTempGroup = BeamLib.GetTempGroup()
@@ -50,15 +50,18 @@ local function LogOutstroke( ptOnToolTipCenter, vtHead, OptionalParameters)
    EgtSetColor( idPoint, RED())
    EgtSetColor( idVector, RED())
 
+   -- nome utensile
+   EgtOutLog( 'Tool ' .. sToolName)
+
    -- si loggano valori di punto e vettore
    EgtOutLog( ' Presimulation : OutStroke, Tip Point = ' .. tostring( ptOnToolTipCenter) .. ', id = ' .. idPoint .. ', vtHead = ' .. tostring( vtHead) .. ', id = ' .. idVector)
 
    -- se disponibili, si loggano anche i valori calcolati degli assi
-   if LinearAxes then
-      EgtOutLog( ' ' .. LinearAxes[1].sName .. ' = ' .. tostring( LinearAxes[1].dValue) .. ', ' .. LinearAxes[2].sName .. ' = ' .. tostring( LinearAxes[2].dValue) .. ', ' .. LinearAxes[3].sName .. ' = ' .. tostring( LinearAxes[3].dValue))
+   if LinearAxesValues then
+      EgtOutLog( ' ' .. 'Lin1' .. ' = ' .. tostring( LinearAxesValues[1]) .. ', ' .. 'Lin2' .. ' = ' .. tostring( LinearAxesValues[2]) .. ', ' .. 'Lin3' .. ' = ' .. tostring( LinearAxesValues[3]))
    end
-   if RotativeAxes then
-      EgtOutLog( ' ' .. RotativeAxes[1].sName .. ' = ' .. tostring( RotativeAxes[1].dValue) .. ', ' .. RotativeAxes[2].sName .. ' = ' .. tostring( RotativeAxes[2].dValue))
+   if RotativeAxesValues then
+      EgtOutLog( ' ' .. 'Rot1' .. ' = ' .. tostring( RotativeAxesValues[1]) .. ', ' .. 'Rot2' .. ' = ' .. tostring( RotativeAxesValues[2]) .. ', ' .. 'Rot3' .. ' = ' .. tostring( RotativeAxesValues[3]))
    end
 
    return
@@ -110,7 +113,7 @@ local function GetToolExitPoint( ptMachining, vtNEdge, vtHead, Tool, bIsDownUp)
 end
 
 -------------------------------------------------------------------------------------------------------------
--- calcolo pivot in riferimento globale, datipunto sull'uscita utensile e direzioni
+-- calcolo pivot in riferimento globale, dati punto sull'uscita utensile e direzioni
 local function GetGlobalPivot( ptToolExit, vtC, vtHead, vtMovePivot)
 
    -- frame solidale all'utensile (lo stesso in cui vtMovePivot è definito)
@@ -150,27 +153,28 @@ local function GetCollisionPointsToCheck( Edge, dDepthToMachine)
 end
 
 -------------------------------------------------------------------------------------------------------------
-local function CheckOutOfStrokePoint( ptOnToolTipCenter, vtHead, nSCC, Tool)
+local function CheckOutOfStrokePoint( ptOnToolTipCenter, vtHead, nSCC, Tool, vtAux, sBlockedAxis)
 
    -- impostazione utensile
-   EgtSetCalcTool( Tool.sName, Tool.sHead, Tool.nExit)
+   local bOkTool = EgtSetCalcTool( Tool.sName, Tool.sHead, Tool.nExit)
+   if not bOkTool then
+      error( 'CheckOutOfStrokePoint : cannot set calc tool')
+   end
 
    -- settaggio SCC per discriminare soluzioni multiple
    EgtSetCalcSolCh( nSCC)
 
-   -- assi macchina da calcolare
-   local LinearAxes, RotativeAxes = GetMachineAxes()
-
-   -- se più di 3 assi lineari e 2 assi rotativi, macchina non supportata
-   if #LinearAxes > 3 or #RotativeAxes > 2 then
-
-      error(' CheckOutOfStrokePoint : too many axes')
+   -- se presente, settaggio asse bloccato
+   if sBlockedAxis and type( sBlockedAxis) == "string" then
+      local BlockedAxis = EgtSplitString( sBlockedAxis, '=')
+      EgtSetRotAxisBlock( BlockedAxis[1], tonumber( BlockedAxis[2]))
    end
 
    -- calcolo assi rotativi
-   local bOkAngles, nSolutionsAngles, dRot1, dRot2 = EgtGetCalcAngles( vtHead)
-   RotativeAxes[1].dValue = dRot1
-   RotativeAxes[2].dValue = dRot2
+   local bOkAngles, nSolutionsAngles, RotativeAxesValues = EgtGetCalcAnglesEx( vtHead, vtAux)
+   local dRotative1 = RotativeAxesValues[1]
+   local dRotative2 = RotativeAxesValues[2]
+   local dRotative3 = RotativeAxesValues[3]
 
    if not bOkAngles then
       error( ' CheckOutOfStrokePoint : error')
@@ -180,61 +184,42 @@ local function CheckOutOfStrokePoint( ptOnToolTipCenter, vtHead, nSCC, Tool)
    if nSolutionsAngles == 0 then
 
       if EgtGetDebugLevel() >= 3 then
-         LogOutstroke( ptOnToolTipCenter, vtHead)
+         LogOutstroke( Tool.sName, ptOnToolTipCenter, vtHead, { RotativeAxesValues = { dRotative1, dRotative2, dRotative3}})
       end
       return true
    end
 
    -- calcolo assi lineari
-   local bOkPositions, _, dLinear1, dLinear2, dLinear3 = EgtGetCalcPositions( ptOnToolTipCenter, RotativeAxes[1].dValue, RotativeAxes[2].dValue)
-   LinearAxes[1].dValue = dLinear1
-   LinearAxes[2].dValue = dLinear2
-   LinearAxes[3].dValue = dLinear3
+   local bOkPositions, _, dLinear1, dLinear2, dLinear3 = EgtGetCalcPositions( ptOnToolTipCenter, dRotative1, dRotative2, dRotative3)
 
    if not bOkPositions then
 
       error( ' CheckOutOfStrokePoint : error')
    end
 
-   -- verifica finecorsa per tutti gli assi
-   -- siccome non si sa a priori il numero di assi lineari e rotativi, si aggiungono tutti a Args in ordine
-   -- Args viene poi esplosa in modo da passare a EgtVerifyOutstroke i valori separati
-   local Args = {}
-   for i = 1, #LinearAxes do
-      Args[#Args+1] = LinearAxes[i].dValue
-   end
-   for i = 1, #RotativeAxes do
-      Args[#Args+1] = RotativeAxes[i].dValue
-   end
-
-   local bAllAxesInStroke = EgtVerifyOutstroke( table.unpack( Args))
+   -- verifica finecorsa per assi lineari (assi rotativi già verificati)
+   local bAllAxesInStroke = EgtVerifyOutstroke( dLinear1, dLinear2, dLinear3)
 
    -- extracorsa
    if not bAllAxesInStroke then
 
       if EgtGetDebugLevel() >= 3 then
-         LogOutstroke( ptOnToolTipCenter, vtHead, { LinearAxes = LinearAxes, RotativeAxes = RotativeAxes})
+         LogOutstroke( Tool.sName, ptOnToolTipCenter, vtHead, { LinearAxesValues = { dLinear1, dLinear2, dLinear3}, RotativeAxesValues = { dRotative1, dRotative2, dRotative3}})
       end
       return true
    end
 
-   -- EgtSetAxisPos( 'T', dT)
-   -- EgtSetAxisPos( 'Y', dY)
-   -- EgtSetAxisPos( 'Z', dZ)
-   -- EgtSetAxisPos( 'C', dC1)
-   -- EgtSetAxisPos( 'A', dA1)
-
    -- se si arriva qui, il punto non è in finecorsa
    return false
 end
 
 -------------------------------------------------------------------------------------------------------------
 -- check extracorsa da punti sul tip dell'utensile
-function PreSimulationLib.CheckOutOfStrokeFromPoints( PointsOnToolTipCenter, vtHead, nSCC, Tool)
+function PreSimulationLib.CheckOutOfStrokeFromPoints( PointsOnToolTipCenter, vtHead, nSCC, Tool, vtAux, sBlockedAxis)
 
    for i = 1, #PointsOnToolTipCenter do
 
-      local bOutOfStroke = CheckOutOfStrokePoint( PointsOnToolTipCenter[i], vtHead, nSCC, Tool)
+      local bOutOfStroke = CheckOutOfStrokePoint( PointsOnToolTipCenter[i], vtHead, nSCC, Tool, vtAux, sBlockedAxis)
 
       -- se trovato extracorsa inutile procedere con gli altri punti
       if bOutOfStroke then
@@ -249,7 +234,7 @@ end
 -------------------------------------------------------------------------------------------------------------
 -- check extracorsa da geometria
 -- TODO da considerare anche gli attacchi
-function PreSimulationLib.CheckOutOfStrokeFromGeometry( idGeometry, vtHead, nSCC, Tool)
+function PreSimulationLib.CheckOutOfStrokeFromGeometry( idGeometry, vtHead, nSCC, Tool, vtAux, sBlockedAxis)
 
    local b3GeomMaxOffset = EgtGetBBoxGlob( idGeometry, GDB_BB.STANDARD)
    local ptBoxCenter = b3GeomMaxOffset:getCenter()
@@ -272,74 +257,127 @@ function PreSimulationLib.CheckOutOfStrokeFromGeometry( idGeometry, vtHead, nSCC
    -- Z-
    table.insert( PointsOnToolTipCenter, Point3d( ptBoxCenter - dBoxDimZ / 2 * Z_AX()))
 
-   local bOutOfStroke = PreSimulationLib.CheckOutOfStrokeFromPoints( PointsOnToolTipCenter, vtHead, nSCC, Tool)
+   local bOutOfStroke = PreSimulationLib.CheckOutOfStrokeFromPoints( PointsOnToolTipCenter, vtHead, nSCC, Tool, vtAux, sBlockedAxis)
 
    return bOutOfStroke
 end
 
 -------------------------------------------------------------------------------------------------------------
-local function CheckCollisionPoint( ptToolExitToCheck, vtC, vtHead, PreCollisionData, Part, bCannotSplitRestLength, sRestLengthSideForPreSimulation, bCheckOnlyRestlength)
+local function MoveMachineAxesToPosition( ptOnToolTipCenter, vtHead, vtAux)
 
-   local ptPivot = GetGlobalPivot( ptToolExitToCheck, vtC, vtHead, PreCollisionData.vtMovePivot)
+   -- calcolo assi rotativi
+   local bOkAngles, nSolutionsAngles, RotativeAxesValues = EgtGetCalcAnglesEx( vtHead, vtAux)
+   local dRotative1 = RotativeAxesValues[1]
+   local dRotative2 = RotativeAxesValues[2]
+   local dRotative3 = RotativeAxesValues[3]
 
-   -- orientamento del riferimento locale
-   local vtDirectionX = PreCollisionData.Directions.vtDirectionX
-   local vtDirectionY = PreCollisionData.Directions.vtDirectionY
-   local vtDirectionZ = PreCollisionData.Directions.vtDirectionZ
+   if not bOkAngles then
+      error( ' MoveMachineAxesToPosition : error')
+   end
 
-   -- costruzione trimesh a partire dalla curva di collisione
-   -- recupero punti da macchina per costruire trimesh
-   local CollisionCurvePoints = PreCollisionData.Points
-   -- curva di collisione in riferimento locale
-   local idCollisionCurve = EgtCurveCompoFromPoints( Part.idTempGroup, CollisionCurvePoints)
-   -- curva in riferimento globale
-   local frReference = Frame3d( ptPivot, vtDirectionZ, vtDirectionX)
-   EgtTransform( idCollisionCurve, frReference, GDB_RT.GLOB)
-   -- trimesh di collisione
-   local idCollisionSurfTm
-   if PreCollisionData.bSurfTmByRevolve then
-      idCollisionSurfTm = EgtSurfTmByRevolve( Part.idTempGroup, idCollisionCurve, ptPivot, vtDirectionY, true, 0.05, GDB_RT.GLOB)
-   else
-      local vtPreMove = -vtDirectionZ * ( PreCollisionData.dExtrusionDepth / 2)
-      EgtMove( idCollisionCurve, vtPreMove, GDB_RT.GLOB)
-      local vtExtrusion = vtDirectionZ * PreCollisionData.dExtrusionDepth
-      idCollisionSurfTm = EgtSurfTmByRegionExtrusion( Part.idTempGroup, idCollisionCurve, vtExtrusion, 0.05, GDB_RT.GLOB)
+   -- calcolo assi lineari
+   local bOkPositions, _, dLinear1, dLinear2, dLinear3 = EgtGetCalcPositions( ptOnToolTipCenter, dRotative1, dRotative2, dRotative3)
+
+   if not bOkPositions then
+
+      error( ' MoveMachineAxesToPosition : error')
+   end
+
+   local AxesNames = EgtGetAllCurrAxesNames()
+   local dTHome = EgtGetAxisHomePos( AxesNames[1])
+
+   -- spostamento assi in posizione (la T non si sposta perchè si sposta direttamente la testa)
+   EgtSetAxisPos( AxesNames[2], dLinear2)
+   EgtSetAxisPos( AxesNames[3], dLinear3)
+   EgtSetAxisPos( AxesNames[4], dRotative1)
+   EgtSetAxisPos( AxesNames[5], dRotative2)
+   if dRotative3 then
+      EgtSetAxisPos( AxesNames[6], dRotative3)
+   end
+
+   return dLinear1 - dTHome
+end
+
+-------------------------------------------------------------------------------------------------------------
+local function CheckCollisionPoint( sAxis, ptOnToolTipCenter, vtHead, vtAux, Part, bCannotSplitRestLength, sRestLengthSideForPreSimulation, idCheckCollisionTm, idAddedCollisionSurfTm)
+
+   -- spostamento assi macchina in posizione
+   local dDeltaXHeadOffset = MoveMachineAxesToPosition( ptOnToolTipCenter, vtHead, vtAux)
+
+   -- si recuperano gli id delle geometrie dell'asse con cui controllare la collisione
+   local idCollisionGroup = EgtGetFirstNameInGroup( EgtGetAxisId( sAxis), 'COLLISION')
+   local idCollisionGroupOther = EgtGetFirstNameInGroup( EgtGetAxisId( sAxis), 'OTHER_COLLISION') or GDB_ID.NULL
+   local CollisionGroupEntitiesId = EgtGetAllInGroup( idCollisionGroup)
+   local CollisionGroupOtherEntitiesId = EgtGetAllInGroup( idCollisionGroupOther)
+   -- si tengono solo gli elementi trimesh
+   local CollisionSurfTmId = {}
+   for i = 1, #CollisionGroupEntitiesId do
+      if EgtGetType( CollisionGroupEntitiesId[i]) == GDB_TY.SRF_MESH then
+         local idCollisionSurfTmCopy = EgtCopyGlob( CollisionGroupEntitiesId[i], Part.idTempGroup)
+         EgtMove( idCollisionSurfTmCopy, Vector3d( dDeltaXHeadOffset, 0, 0), GDB_RT.GLOB)
+         table.insert( CollisionSurfTmId, idCollisionSurfTmCopy)
+      end
+   end
+   -- se presenti geometrie nel gruppo other si aggiungono anche quelle
+   if CollisionGroupOtherEntitiesId and #CollisionGroupOtherEntitiesId > 0 then
+      for i = 1, #CollisionGroupOtherEntitiesId do
+         if EgtGetType( CollisionGroupOtherEntitiesId[i]) == GDB_TY.SRF_MESH then
+            local idCollisionOtherSurfTmCopy = EgtCopyGlob( CollisionGroupOtherEntitiesId[i], Part.idTempGroup)
+            EgtMove( idCollisionOtherSurfTmCopy, Vector3d( dDeltaXHeadOffset, 0, 0), GDB_RT.GLOB)
+            table.insert( CollisionSurfTmId, idCollisionOtherSurfTmCopy)
+         end
+      end
+   end
+   -- se presente si aggiunge la geometria opzionale (es: flangia lama)
+   if idAddedCollisionSurfTm then
+      table.insert( CollisionSurfTmId, idAddedCollisionSurfTm)
    end
 
    -- check collisione con pezzo
    local bCollisionFoundPiece = false
-   if not bCheckOnlyRestlength then
-      local idCheckCollisionTm = Part.idBoxTm
+   if not idCheckCollisionTm then
+      idCheckCollisionTm = Part.idBoxTm
       -- se testa o coda attaccate, si considerano nella superficie di collisione
       if bCannotSplitRestLength then
          local b3CheckCollision = BeamLib.GetPartBoxWithHeadTail( Part, sRestLengthSideForPreSimulation)
          idCheckCollisionTm = EgtSurfTmBBox( Part.idTempGroup, b3CheckCollision, false, GDB_RT.GLOB)
       end
-      bCollisionFoundPiece = EgtCDeSolidSolid( idCheckCollisionTm, idCollisionSurfTm, BeamData.COLL_SIC)
+   end
+   for i = 1, #CollisionSurfTmId do
+      bCollisionFoundPiece = EgtCDeSolidSolid( idCheckCollisionTm, CollisionSurfTmId[i], BeamData.COLL_SIC)
       if not type( bCollisionFoundPiece) == "boolean" then
          error( 'Presimulation fail')
       end
       if EgtGetDebugLevel() >= 3 and bCollisionFoundPiece then
-         EgtSetColor( idCollisionSurfTm, RED())
+         EgtSetColor( CollisionSurfTmId[i], RED())
       end
+      if bCollisionFoundPiece then
+         break
+      end
+   end
 
       -- se trovata collisione con pezzo è inutile procedere con il grezzo
       if bCollisionFoundPiece then
+
          return true
       end
-   end
 
    -- check collisione con grezzo restante, se con il pezzo non c'è collisione e non è un taglio di testa o coda
    local bCollisionFoundRestLength = false
    if not ( bCollisionFoundPiece or bCannotSplitRestLength) then
       local idRestLengthSurfFr = GetRestlengthSurfTm( Part, sRestLengthSideForPreSimulation)
       if idRestLengthSurfFr then
-         bCollisionFoundRestLength = EgtCDeSolidSolid( idRestLengthSurfFr, idCollisionSurfTm, BeamData.COLL_SIC)
-         if not type( bCollisionFoundRestLength) == "boolean" then
-            error( 'Presimulation fail')
-         end
-         if EgtGetDebugLevel() >= 3 and bCollisionFoundRestLength then
-            EgtSetColor( idCollisionSurfTm, ORANGE())
+         for i = 1, #CollisionSurfTmId do
+            bCollisionFoundRestLength = EgtCDeSolidSolid( idRestLengthSurfFr, CollisionSurfTmId[i], BeamData.COLL_SIC)
+            if not type( bCollisionFoundRestLength) == "boolean" then
+               error( 'Presimulation fail')
+            end
+            if EgtGetDebugLevel() >= 3 and bCollisionFoundRestLength then
+               EgtSetColor( CollisionSurfTmId[i], ORANGE())
+            end
+            if bCollisionFoundRestLength then
+               break
+            end
          end
       end
    end
@@ -361,46 +399,50 @@ local function CheckCollisionWithAxis( sAxis, MachiningParameters, OptionalParam
 
    -- parametri opzionali
    OptionalParameters = OptionalParameters or {}
-   local bCheckOnlyRestlength = OptionalParameters.bCheckOnlyRestlength or false
+   local idCheckCollisionTm = OptionalParameters.idCheckCollisionTm
    local sRestLengthSideForPreSimulation = OptionalParameters.sRestLengthSideForPreSimulation or 'Tail'
    local bCannotSplitRestLength = OptionalParameters.bCannotSplitRestLength or false
+   local vtAux = OptionalParameters.vtAux
 
    -- se normale faccia non parallela a direzione testa c'è qualcosa che non va
    if not AreSameOrOppositeVectorApprox( vtNFace, vtHead) then
       error( 'CheckCollisionWithAxis : invalid directions')
    end
-   
+
    -- punti notevoli della lavorazione in cui fare il check
    local PointsToCheck = OptionalParameters.PointsToCheck or GetCollisionPointsToCheck( Edge, dDepthToMachine)
 
-   -- punti in centro lama su naso mandrino o aggregato. In base a direzione e punto
-   local bIsDownUp = AreOppositeVectorApprox( vtNFace, vtHead)
-   local ToolExitPoints = {}
+   -- punti sul tip dell'utensile, in centro
+   local PointsOnToolTipCenter = {}
    for i = 1, #PointsToCheck do
-      ToolExitPoints[i] = GetToolExitPoint( PointsToCheck[i], Edge.vtN, vtHead, Tool, bIsDownUp)
+      PointsOnToolTipCenter[i] = PreSimulationLib.GetPointOnToolTipCenter( PointsToCheck[i], vtHead, vtNFace, Edge.vtN, Tool)
    end
 
-   -- vtC punta sempre verso il corpo dell'asse C o verso l'aggregato
-   local nSCC = Tool.SetupInfo.GetSCC( Edge.vtN, Edge.vtEdge, vtNFace)
-   local vtSCC = BeamLib.GetDirectionFromSCC( nSCC)
-   local vtC = vtHead ^ Tool.SetupInfo.vtRotationAxisC
-   vtC:normalize()
-   if vtC:isZero() then
-      vtC = vtSCC
-   elseif vtC * vtSCC < GEO.EPS_SMALL then
-      vtC = -vtC
-   end
-
-   -- punti curva collisione e direzioni check da macchina
-   local PreCollisionData = Tool.SetupInfo.GetPreCollisionData( sAxis, vtC, vtHead)
-
    local bMoveAfterSplit = false
 
    -- se almeno in un punto c'è collisione con il pezzo si ritorna collisione
    -- se non si trova collisione si ritorna se è necessario separare prima di effettuare la lavorazione (ossia non c'è collisione con il pezzo ma c'è con il grezzo restante)
-   for i = 1, #ToolExitPoints do
+   for i = 1, #PointsOnToolTipCenter do
 
-      local bCollisionFoundPiece, bCollisionFoundRestLength = CheckCollisionPoint( ToolExitPoints[i], vtC, vtHead, PreCollisionData, Part, bCannotSplitRestLength, sRestLengthSideForPreSimulation, bCheckOnlyRestlength)
+      -- se lama con flangia si aggiunge quest'ultima ai solidi di collisione, ipotizzandola grande fino al dMaxDepth + sicurezza
+      local idAddedCollisionSurfTm
+      if Tool.sType == 'SAW_FLAT' then
+         local ptCenterFlange = PointsOnToolTipCenter[i] + vtHead * Tool.dThickness
+         local frHead = Frame3d( ptCenterFlange, vtHead)
+         local dExtraSafety = 2 -- valore empirico che serve nei casi molto inclinati, ci potrebbero essere casi in cui va aumentato
+         local idFlangeCurve = EgtCircle( Part.idTempGroup, ORIG(), dExtraSafety + Tool.dDiameter / 2 - Tool.dMaxDepth, GDB_RT.GLOB)
+         EgtTransform( idFlangeCurve, frHead, GDB_RT.GLOB)
+
+         -- TODO verificare se questo controllo serve
+         if AreOppositeVectorApprox( vtHead, EgtCurveExtrusion( idFlangeCurve)) then
+            EgtInvertCurve( idFlangeCurve)
+         end
+         
+         local vtExtrusion = 15 * vtHead
+         idAddedCollisionSurfTm = EgtSurfTmByRegionExtrusion( Part.idTempGroup, idFlangeCurve, vtExtrusion, 0.05, GDB_RT.GLOB)
+      end
+
+      local bCollisionFoundPiece, bCollisionFoundRestLength = CheckCollisionPoint( sAxis, PointsOnToolTipCenter[i], vtHead, vtAux, Part, bCannotSplitRestLength, sRestLengthSideForPreSimulation, idCheckCollisionTm, idAddedCollisionSurfTm)
 
       -- se trovata collisione con pezzo è inutile controllare gli altri punti
       if bCollisionFoundPiece then
@@ -419,29 +461,33 @@ local function CheckCollisionWithAxis( sAxis, MachiningParameters, OptionalParam
 end
 
 -------------------------------------------------------------------------------------------------------------
-function PreSimulationLib.CheckCollision( sBladeEngagement, Parameters, OptionalParameters)
+function PreSimulationLib.CheckCollision( Parameters, OptionalParameters)
 
    local bCollisionFound
-   local bMoveAfterSplitZ, bMoveAfterSplitC, bMoveAfterSplitAB
+   local bMoveAfterSplitL3, bMoveAfterSplitR3, bMoveAfterSplitR2, bMoveAfterSplitR1
+
+   -- parametri obbligatori
+   local Edge = Parameters.Edge
+   local vtNFace = Parameters.vtNFace
+   local Tool = Parameters.Tool
 
    -- parametri opzionali, in parte da far transitare
    OptionalParameters = OptionalParameters or {}
 
    local OptionalParametersCheckCollisionWithAxis = {}
-   OptionalParametersCheckCollisionWithAxis.bCheckOnlyRestlength = false
    OptionalParametersCheckCollisionWithAxis.PointsToCheck = OptionalParameters.PointsToCheck or nil
    OptionalParametersCheckCollisionWithAxis.sRestLengthSideForPreSimulation = OptionalParameters.sRestLengthSideForPreSimulation or 'Tail'
    OptionalParametersCheckCollisionWithAxis.bCannotSplitRestLength = OptionalParameters.bCannotSplitRestLength or false
+   OptionalParametersCheckCollisionWithAxis.sBlockedAxis = OptionalParameters.sBlockedAxis
+   OptionalParametersCheckCollisionWithAxis.vtAux = OptionalParameters.vtAux
+   OptionalParametersCheckCollisionWithAxis.idCheckCollisionTm = OptionalParameters.idCheckCollisionTm
 
-   local bIsDicing = OptionalParameters.bIsDicing or false
-   local bCheckOnlyRestlengthForAxisABC = false
+   local sBlockedAxis = OptionalParameters.sBlockedAxis
+   local bDisableRealElevationCheck = OptionalParameters.bDisableRealElevationCheck or false
 
-   -- se cubetti in modalità standard (no DownUp) gli assi AB e C si controllano solo con grezzo (ci sarebbe collisione con il materiale già rimosso controllando AB e C con pezzo)
-   if bIsDicing and ( sBladeEngagement == 'Standard') then
-      bCheckOnlyRestlengthForAxisABC = true
    -- se l'elevazione reale (rispetto al pezzo + eventuale materiale in testa/coda) è maggiore del massimo materiale è sempre collisione
    -- TODO rifare con funzione
-   else
+   if not bDisableRealElevationCheck then
       local Edge = Parameters.Edge
       local vtNFace = Parameters.vtNFace
       local dDepthToMachine = Parameters.dDepthToMachine
@@ -464,21 +510,43 @@ function PreSimulationLib.CheckCollision( sBladeEngagement, Parameters, Optional
       end
    end
 
-   -- asse Z si controlla sempre
-   bCollisionFound, bMoveAfterSplitZ = CheckCollisionWithAxis( 'Z', Parameters, OptionalParametersCheckCollisionWithAxis)
+   -- SCC
+   local nSCC = Tool.SetupInfo.GetSCC( Edge.vtN, Edge.vtEdge, vtNFace)
 
-   -- assi AB e C: se richiesto si controlla la collisione solo col grezzo
-   OptionalParametersCheckCollisionWithAxis.bCheckOnlyRestlength = bCheckOnlyRestlengthForAxisABC
+   -- si settano utensile, SCC e asse bloccato per il controllo collisione
+   local bOkTool = EgtSetCalcTool( Tool.sName, Tool.sHead, Tool.nExit)
+   if not bOkTool then
+      error( 'CheckCollisionWithAxis : cannot set calc tool')
+   end
+   EgtSetCalcSolCh( nSCC)
+   if sBlockedAxis and type( sBlockedAxis) == "string" then
+      local BlockedAxis = EgtSplitString( sBlockedAxis, '=')
+      EgtSetRotAxisBlock( BlockedAxis[1], tonumber( BlockedAxis[2]))
+   end
 
-   if not bCollisionFound then
-      bCollisionFound, bMoveAfterSplitAB = CheckCollisionWithAxis( 'AB', Parameters, OptionalParametersCheckCollisionWithAxis)
+   -- nomi degli assi con cui controllare la collisione
+   local AxesNames = EgtGetAllCurrAxesNames()
+   local sL3 = AxesNames[3]
+   local sR3 = AxesNames[6]
+   local sR2 = AxesNames[5]
+   local sR1 = AxesNames[4]
+
+   -- ultimo asse lineare prima dei rotativi (solitamente Z) si controlla sempre
+   bCollisionFound, bMoveAfterSplitL3 = CheckCollisionWithAxis( sL3, Parameters, OptionalParametersCheckCollisionWithAxis)
+
+   if sR3 and not bCollisionFound then
+      bCollisionFound, bMoveAfterSplitR3 = CheckCollisionWithAxis( sR3, Parameters, OptionalParametersCheckCollisionWithAxis)
    end
 
    if not bCollisionFound then
-      bCollisionFound, bMoveAfterSplitC = CheckCollisionWithAxis( 'C', Parameters, OptionalParametersCheckCollisionWithAxis)
+      bCollisionFound, bMoveAfterSplitR2 = CheckCollisionWithAxis( sR2, Parameters, OptionalParametersCheckCollisionWithAxis)
    end
 
-   local bMoveAfterSplit = bMoveAfterSplitZ or bMoveAfterSplitC or bMoveAfterSplitAB
+   if not bCollisionFound then
+      bCollisionFound, bMoveAfterSplitR1 = CheckCollisionWithAxis( sR1, Parameters, OptionalParametersCheckCollisionWithAxis)
+   end
+
+   local bMoveAfterSplit = bMoveAfterSplitL3 or bMoveAfterSplitR3 or bMoveAfterSplitR2 or bMoveAfterSplitR1
 
    return bCollisionFound, bMoveAfterSplit
 end

Messages/EgalTechEng.txt

@@ -0,0 +1,322 @@
+// Message File EgalTech English  2026/06/23
+0=ENG
+// ----- BeamNew -----
+1000001=Part loading position
+1000002=Part loading position
+1000003=Loading position from BTL, no pre-rotation
+1000004=Loading position from BTL, no pre-rotation
+1000005=Get Best loading position from 0° and 180°
+1000006=Get Best loading position from 0° and 180°
+1000007=Get Best loading position in each piece rotation
+1000008=Get Best loading position in each piece rotation
+1000009=Allow piece inversion
+1000010=Allow piece inversion
+1000011=Enable material optimization function in nesting (part rotation disabled)
+1000012=Enable material optimization function in nesting (part rotation disabled)
+1000013=Part rotating acceptability
+1000014=Acceptability of rotating the part between machining steps
+1000015=Rotation not allowed
+1000016=Rotation not allowed
+1000017=Rotation allowed only if strictly necessary
+1000018=Rotation allowed only if strictly necessary
+1000019=Rotation easily acceptable / no constraint
+1000020=Rotation easily acceptable / no constraint
+1000021=Machining Strategy
+1000022=Machining Strategy
+1000023=Quality and time equally prioritized
+1000024=Quality and time equally prioritized
+1000025=Fastest
+1000026=Prefer fastest strategies
+1000027=High quality
+1000028=Prefer high-quality strategies
+1000029=Ordering rules
+1000030=The first complete strategy in list is the one chosen; no intelligent choosing
+1000031=Max number of reprocessing cycles
+1000032=Max number of reprocessing cycles
+1000033=Use entire blade diameter to shorten path
+1000034=Use entire blade diameter to shorten path
+1000035=Maximum length for dropped waste
+1000036=Maximum length for dropped waste
+1000037=Maximum volume for dropped waste
+1000038=Maximum volume for dropped waste
+1000039=Maximum dice dimension
+1000040=Maximum dice dimension
+1000041=Overmaterial on tenon length
+1000042=Overmaterial on tenon length
+1000043=Overmaterial on tenon width
+1000044=Overmaterial on tenon width
+1000045=Maximum number of milling passes
+1000046=Maximum number of milling passes. If more passes are required, pocketing is performed
+1000047=Use DoveTail tool to pocket
+1000048=Use DoveTail tool to pocket
+1000049=Cutting Strategy
+1000050=Cutting Strategy
+1000051=Automatic
+1000052=Automatic
+1000053=Blade only
+1000054=Blade only
+1000055=Mill only
+1000056=Mill only
+1000057=ChainSaw only
+1000058=ChainSaw only
+1000059=Available mill to machine the tenon cut surface
+1000060=Available mill to machine the tenon cut surface
+1000061=Available mill to machine the dovetail tenon
+1000062=Available mill to machine the dovetail tenon
+1000063=Max radius left on corners
+1000064=Radius-limit left by the tool at each corner of the feature
+1000065=Use Anti-Splint strategy
+1000066=The strategy will apply blade cuts on corner to avoid wood splint
+1000067=Extend after tail
+1000068=The automatism considers this length as machinable. This means you accept to damage the next piece in the bar
+1000069=Minimum approach distance on open sides
+1000070=Minimum approach distance on open sides
+1000071=Available mill to pocket the feature
+1000072=Available mill to pocket the feature
+1000073=Finish with chainsaw if needed
+1000074=Finish with chainsaw if needed
+1000075=Extend after tail
+1000076=The automatism considers this length as machinable. This means you accept to damage the next piece in the bar
+1000077=Force ripping blade
+1000078=Force the use of ripping blade, designed for cuts parallel to the grain
+1000079=Not complete with Blade radius imprint left
+1000080=If the parameter is active, the automatism considers the feature as - not complete - if the blade radius imprint is left
+1000081=Use Zig-Zag ChainSaw
+1000082=Enable the parameter to set the Zig-Zag movement on the ChainSaw machining. Deactivate it to use One-Way movement.
+1000083=Sort by segment
+1000084=Sort the machinings according to the piece-segment where the machining has inserted
+1000085=Damage next piece
+1000086=This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time
+1000087=Never damage
+1000088=Never damage
+1000089=Damage only if raw
+1000090=Damage only if raw
+1000091=Can damage
+1000092=Can damage
+1000093=Use Zig-Zag ChainSaw
+1000094=Enable the parameter to set the Zig-Zag movement on the ChainSaw machining. Deactivate it to use One-Way movement.
+1000095=Extend after tail
+1000096=The automatism considers this length as machinable. This means you accept to damage the next piece in the bar
+1000097=Damage next piece
+1000098=This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time
+1000099=Never damage
+1000100=Never damage
+1000101=Damage only if raw
+1000102=Damage only if raw
+1000103=Can damage
+1000104=Can damage
+1000105=Force ripping blade
+1000106=Force the use of ripping blade, designed for cuts parallel to the grain
+1000107=Extend after tail
+1000108=The automatism considers this length as machinable. This means you accept to damage the next piece in the bar
+1000109=Damage next piece
+1000110=This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time
+1000111=Never damage
+1000112=Never damage
+1000113=Damage only if raw
+1000114=Damage only if raw
+1000115=Can damage
+1000116=Can damage
+1000117=Cutting strategy
+1000118=Cutting strategy
+1000119=Automatic
+1000120=Automatic
+1000121=Drop waste
+1000122=Drop waste
+1000123=Keep waste attached
+1000124=Keep waste attached
+1000125=Disable dicing
+1000126=Disable dicing
+1000127=Prioritize machining speed over quality
+1000128=Prioritize machining speed over quality
+1000129=Strip width
+1000130=In case the waste is still kept attached, this is the wigth dimension of the strip
+1000131=Clean blade radius with mill
+1000132=Clean blade radius with mill
+1000133=Milling offset from side
+1000134=Milling offset from side
+1000135=Overmaterial on tenon length
+1000136=Overmaterial on tenon length
+1000137=Overmaterial on tenon width
+1000138=Overmaterial on tenon width
+1000139=Maximum number of milling passes
+1000140=Maximum number of milling passes. If more passes are required, pocketing is performed
+1000141=Cutting Strategy
+1000142=Cutting Strategy
+1000143=Automatic
+1000144=Automatic
+1000145=Blade only
+1000146=Blade only
+1000147=Mill only
+1000148=Mill only
+1000149=ChainSaw only
+1000150=ChainSaw only
+1000151=Available mill to machine the tenon
+1000152=Available mill to machine the tenon
+1000153=Overmaterial on Mortise length
+1000154=Overmaterial on Mortise length
+1000155=Overmaterial on Mortise width
+1000156=Overmaterial on Mortise width
+1000157=Maximum number of milling passes
+1000158=Maximum number of milling passes. If more passes are required, pocketing is performed
+1000159=Use DoveTail tool in case of pocketing
+1000160=Use DoveTail tool in case of pocketing
+1000161=Add Anti-Splint
+1000162=Add Anti-Splint
+1000163=Cutting Strategy
+1000164=Cutting Strategy
+1000165=Automatic
+1000166=Automatic
+1000167=Blade only
+1000168=Blade only
+1000169=Mill only
+1000170=Mill only
+1000171=ChainSaw only
+1000172=ChainSaw only
+1000173=Available mill to machine the mortise cut surface
+1000174=Available mill to machine the mortise cut surface
+1000175=Available mill to machine the dovetail mortise
+1000176=Available mill to machine the dovetail mortise
+1000177=Overmaterial on mortise length
+1000178=Overmaterial on mortise length
+1000179=Overmaterial on mortise width
+1000180=Overmaterial on mortise width
+1000181=Cutting Strategy
+1000182=Cutting Strategy
+1000183=Automatic
+1000184=Automatic
+1000185=Blade only
+1000186=Blade only
+1000187=Mill only
+1000188=Mill only
+1000189=ChainSaw only
+1000190=ChainSaw only
+1000191=Available mill to machine the mortise cut surface
+1000192=Available mill to machine the mortise cut surface
+1000193=Available mill to machine the mortise
+1000194=Available mill to machine the mortise
+1000195=Depth Chamfer
+1000196=Depth of the V-Mill to execute chamfers on cut-edges
+1000197=Use Anti-Splint strategy
+1000198=The strategy will apply blade cuts on corner to avoid wood splint
+1000199=Available mill to machine the profile
+1000200=Available mill to machine the profile
+1000201=Antisplint with blade
+1000202=Use the blade as antisplint in case the geometry is not through
+1000203=Extend after tail
+1000204=The automatism considers this length as machinable. This means you accept to damage the next piece in the bar
+1000205=Clean radius with mill
+1000206=Clean radius with mill
+1000207=Milling offset from side
+1000208=Milling offset from side
+1000209=Damage next piece
+1000210=This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time
+1000211=Never damage
+1000212=Never damage
+1000213=Damage only if raw
+1000214=Damage only if raw
+1000215=Can damage
+1000216=Can damage
+1000217=Tolerance on Diameter
+1000218=Tolerance on Diameter
+1000219=Depth PreHole
+1000220=Depth PreHole
+1000221=Drilling Mode
+1000222=Drilling Mode
+1000223=Automatic
+1000224=Automatic
+1000225=Preferred machining from one side only
+1000226=Preferred machining from one side only
+1000227=Force machining from two sides
+1000228=Force machining from two sides
+1000229=Available Drillbit list
+1000230=Available Drillbit list
+1000231=Extend after tail
+1000232=The automatism considers this length as machinable. This means you accept to damage the next piece in the bar
+1000233=Damage next piece
+1000234=This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time
+1000235=Never damage
+1000236=Never damage
+1000237=Damage only if raw
+1000238=Damage only if raw
+1000239=Can damage
+1000240=Can damage
+1000241=Ridge Lap strategy
+1000242=Ridge Lap strategy
+1000243=Automatic
+1000244=Automatic
+1000245=Use blade
+1000246=Use blade
+1000247=Use mill
+1000248=Use mill
+1000249=Tolerance on Diameter
+1000250=Tolerance on Diameter
+1000251=Use mill as a drillbit
+1000252=Admit to use the mill as a drillbit
+1000253=Execute contour only
+1000254=Execute the contour anyway, even the hole is bigger than the tool diameter
+1000255=Drilling mode
+1000256=Drilling mode
+1000257=Automatic
+1000258=Automatic
+1000259=Preferred machining from one side only
+1000260=Preferred machining from one side only
+1000261=Force machining from two sides
+1000262=Force machining from two sides
+1000263=Available mill to machine drills
+1000264=Available mill to machine drills
+1000265=Machining Depth
+1000266=Machining Depth
+1000267=Available mill to machine mark and text
+1000268=Available mill to machine mark and text
+1000269=Marking Strategy
+1000270=Marking Strategy
+1000271=Automatic
+1000272=Automatic
+1000273=Pen only
+1000274=Pen only
+1000275=V-Mill only
+1000276=V-Mill only
+1000277=Depth Chamfer
+1000278=Depth of the V-Mill to execute chamfers on cut-edges
+1000279=Only Chamfer
+1000280=Execute the chamfer only, no other machining
+1000281=Overmaterial
+1000282=Overmaterial
+1000283=Max radius left on corners
+1000284=Radius-limit left by the tool at each corner of the feature
+1000285=Execute cut to remove material
+1000286=Execute cut to remove material
+1000287=Force strip
+1000288=Enable the parameter to force the software to leave a strip to sustain the piece
+1000289=Strip width
+1000290=Width of the strip in case if foreseen from the machining
+1000291=Cutting Strategy
+1000292=Cutting Strategy
+1000293=Automatic
+1000294=Automatic
+1000295=No machining
+1000296=No machining
+1000297=Blade forced
+1000298=Blade forced
+1000299=Mill forced
+1000300=Mill forced
+1000301=Available mill to machine the profile
+1000302=Available mill to machine the profile
+1000303=Depth Chamfer
+1000304=Depth of the V-Mill to execute chamfers on cut-edges
+1000305=Force to use chain saw
+1000306=Force to use chain saw
+1000307=Force to add PreCuts
+1000308=Autocam will apply a machining on the theoretical zero, to avoid collision if the theoretical piece length doesn't correspond to the real length
+1000309=Finish with mill
+1000310=Use a mill to finish the surface if split with chain saw
+1000311=Depth Chamfer
+1000312=Depth of the V-Mill to execute chamfers on cut-edges
+1000313=Force to use chain saw
+1000314=Force to use chain saw
+1000315=Force to add PreCuts
+1000316=Autocam will apply a machining on the theoretical zero, to avoid collision if the theoretical piece length doesn't correspond to the real length
+1000317=Finish with mill
+1000318=Use a mill to finish the surface if split with chain saw
+// ----- End -----

Messages/EgalTechIta.txt

@@ -0,0 +1,322 @@
+// File dei messaggi EgalTech Italiano  2026/06/23
+0=ITA
+// ----- BeamNew -----
+1000001=Posizione di caricamento pezzo
+1000002=Posizione di caricamento pezzo
+1000003=Posizione di caricamento da BTL, senza pre-rotazione
+1000004=Posizione di caricamento da BTL, senza pre-rotazione
+1000005=Ottieni la migliore posizione di caricamento tra 0° e 180°
+1000006=Ottieni la migliore posizione di caricamento tra 0° e 180°
+1000007=Ottieni la migliore posizione di caricamento per ogni rotazione del pezzo
+1000008=Ottieni la migliore posizione di caricamento per ogni rotazione del pezzo
+1000009=Consenti inversione pezzo
+1000010=Consenti inversione pezzo
+1000011=Abilita funzione di ottimizzazione materiale nel nesting (rotazione pezzo disabilitata)
+1000012=Abilita funzione di ottimizzazione materiale nel nesting (rotazione pezzo disabilitata)
+1000013=Accettabilità rotazione pezzo
+1000014=Accettabilità della rotazione del pezzo tra le fasi di lavorazione
+1000015=Rotazione non consentita
+1000016=Rotazione non consentita
+1000017=Rotazione consentita solo se strettamente necessaria
+1000018=Rotazione consentita solo se strettamente necessaria
+1000019=Rotazione facilmente accettabile / nessun vincolo
+1000020=Rotazione facilmente accettabile / nessun vincolo
+1000021=Strategia di lavorazione
+1000022=Strategia di lavorazione
+1000023=Qualità e tempo considerati con la stessa priorità
+1000024=Qualità e tempo considerati con la stessa priorità
+1000025=Più veloce
+1000026=Preferisci le strategie più veloci
+1000027=Alta qualità
+1000028=Preferisci le strategie ad alta qualità
+1000029=Regole di ordinamento
+1000030=La prima strategia completa in lista è quella scelta; nessuna scelta intelligente
+1000031=Numero massimo di cicli di rilavorazione
+1000032=Numero massimo di cicli di rilavorazione
+1000033=Usa l'intero diametro della lama per accorciare il percorso
+1000034=Usa l'intero diametro della lama per accorciare il percorso
+1000035=Massima lunghezza per lo scarto caduto
+1000036=Massima lunghezza per lo scarto caduto
+1000037=Massimo volume per lo scarto caduto
+1000038=Massimo volume per lo scarto caduto
+1000039=Dimensione massima dei cubetti
+1000040=Dimensione massima dei cubetti
+1000041=Sovramateriale sulla lunghezza del tenone
+1000042=Sovramateriale sulla lunghezza del tenone
+1000043=Sovramateriale sulla larghezza del tenone
+1000044=Sovramateriale sulla larghezza del tenone
+1000045=Numero massimo di passate di fresatura
+1000046=Numero massimo di passate di fresatura. Se sono necessarie più passate, viene eseguita la svuotatura
+1000047=Utilizza l'utensile a coda di rondine per svuotare
+1000048=Utilizza l'utensile a coda di rondine per svuotare
+1000049=Strategia di taglio
+1000050=Strategia di taglio
+1000051=Automatico
+1000052=Automatico
+1000053=Solo lama
+1000054=Solo lama
+1000055=Solo fresa
+1000056=Solo fresa
+1000057=Solo sega a catena
+1000058=Solo sega a catena
+1000059=Fresa disponibile per lavorare la superficie di taglio del tenone
+1000060=Fresa disponibile per lavorare la superficie di taglio del tenone
+1000061=Fresa disponibile per lavorare il tenone a coda di rondine
+1000062=Fresa disponibile per lavorare il tenone a coda di rondine
+1000063=Raggio massimo rimasto sugli spigoli
+1000064=Limite del raggio lasciato dall'utensile ad ogni spigolo della feature
+1000065=Utilizza la strategia antischeggia
+1000066=La strategia applicherà tagli di lama sullo spigolo per evitare scheggiature del legno
+1000067=Estendi dopo la coda
+1000068=L'automatismo considera questa lunghezza come lavorabile. Questo significa che si accetta di danneggiare il pezzo successivo nella barra
+1000069=Distanza minima di approccio sui lati aperti
+1000070=Distanza minima di approccio sui lati aperti
+1000071=Fresa disponibile per svuotare la feature
+1000072=Fresa disponibile per svuotare la feature
+1000073=Finisci con sega a catena se necessario
+1000074=Finisci con sega a catena se necessario
+1000075=Estendi dopo la coda
+1000076=L'automatismo considera questa lunghezza come lavorabile. Questo significa che si accetta di danneggiare il pezzo successivo nella barra
+1000077=Forza lama da scasso
+1000078=Forza l'uso della lama da scasso, progettata per tagli paralleli alla venatura
+1000079=Non completare se rimane l'impronta del raggio della lama
+1000080=Se il parametro è attivo, l'automatismo considera la feature come - non completa - se rimane l'impronta del raggio della lama
+1000081=Utilizza sega a catena in Zig-Zag
+1000082=Abilita il parametro per impostare il movimento Zig-Zag sulla lavorazione della sega a catena. Disattivarlo per utilizzare il movimento One-Way.
+1000083=Ordina per segmento
+1000084=Ordina le lavorazioni in base al segmento del pezzo in cui la lavorazione è inserita
+1000085=Danneggia il pezzo successivo
+1000086=Questa opzione consente di decidere come considerare il pezzo successivo nella barra. Il software calcola specifici ingressi/uscite per rispettare il parametro. Questo parametro può variare il tempo di lavorazione
+1000087=Non danneggiare mai
+1000088=Non danneggiare mai
+1000089=Danneggia solo se grezzo
+1000090=Danneggia solo se grezzo
+1000091=Può danneggiare
+1000092=Può danneggiare
+1000093=Utilizza sega a catena in Zig-Zag
+1000094=Abilita il parametro per impostare il movimento Zig-Zag sulla lavorazione della sega a catena. Disattivarlo per utilizzare il movimento One-Way.
+1000095=Estendi dopo la coda
+1000096=L'automatismo considera questa lunghezza come lavorabile. Questo significa che si accetta di danneggiare il pezzo successivo nella barra
+1000097=Danneggia il pezzo successivo
+1000098=Questa opzione consente di decidere come considerare il pezzo successivo nella barra. Il software calcola specifici ingressi/uscite per rispettare il parametro. Questo parametro può variare il tempo di lavorazione
+1000099=Non danneggiare mai
+1000100=Non danneggiare mai
+1000101=Danneggia solo se grezzo
+1000102=Danneggia solo se grezzo
+1000103=Può danneggiare
+1000104=Può danneggiare
+1000105=Forza lama da scasso
+1000106=Forza l'uso della lama da scasso, progettata per tagli paralleli alla venatura
+1000107=Estendi dopo la coda
+1000108=L'automatismo considera questa lunghezza come lavorabile. Questo significa che si accetta di danneggiare il pezzo successivo nella barra
+1000109=Danneggia il pezzo successivo
+1000110=Questa opzione consente di decidere come considerare il pezzo successivo nella barra. Il software calcola specifici ingressi/uscite per rispettare il parametro. Questo parametro può variare il tempo di lavorazione
+1000111=Non danneggiare mai
+1000112=Non danneggiare mai
+1000113=Danneggia solo se grezzo
+1000114=Danneggia solo se grezzo
+1000115=Può danneggiare
+1000116=Può danneggiare
+1000117=Strategia di taglio
+1000118=Strategia di taglio
+1000119=Automatico
+1000120=Automatico
+1000121=Scarica lo scarto
+1000122=Scarica lo scarto
+1000123=Mantieni lo scarto attaccato
+1000124=Mantieni lo scarto attaccato
+1000125=Disabilita la tassellatura
+1000126=Disabilita la tassellatura
+1000127=Dai priorità alla velocità di lavorazione rispetto alla qualità
+1000128=Dai priorità alla velocità di lavorazione rispetto alla qualità
+1000129=Larghezza del testimone
+1000130=Nel caso in cui lo scarto venga mantenuto attaccato, questa è la dimensione della larghezza del testimone
+1000131=Pulisci il raggio della lama con la fresa
+1000132=Pulisci il raggio della lama con la fresa
+1000133=Offset di fresatura dal lato
+1000134=Offset di fresatura dal lato
+1000135=Sovramateriale sulla lunghezza del tenone
+1000136=Sovramateriale sulla lunghezza del tenone
+1000137=Sovramateriale sulla larghezza del tenone
+1000138=Sovramateriale sulla larghezza del tenone
+1000139=Numero massimo di passate di fresatura
+1000140=Numero massimo di passate di fresatura. Se sono necessarie più passate, viene eseguita la svuotatura
+1000141=Strategia di taglio
+1000142=Strategia di taglio
+1000143=Automatico
+1000144=Automatico
+1000145=Solo lama
+1000146=Solo lama
+1000147=Solo fresa
+1000148=Solo fresa
+1000149=Solo sega a catena
+1000150=Solo sega a catena
+1000151=Fresa disponibile per lavorare il tenone
+1000152=Fresa disponibile per lavorare il tenone
+1000153=Sovramateriale sulla lunghezza della mortasa
+1000154=Sovramateriale sulla lunghezza della mortasa
+1000155=Sovramateriale sulla larghezza della mortasa
+1000156=Sovramateriale sulla larghezza della mortasa
+1000157=Numero massimo di passate di fresatura
+1000158=Numero massimo di passate di fresatura. Se sono necessarie più passate, viene eseguita la svuotatura
+1000159=Utilizza l'utensile a coda di rondine in caso di svuotatura
+1000160=Utilizza l'utensile a coda di rondine in caso di svuotatura
+1000161=Aggiungi antischeggia
+1000162=Aggiungi antischeggia
+1000163=Strategia di taglio
+1000164=Strategia di taglio
+1000165=Automatico
+1000166=Automatico
+1000167=Solo lama
+1000168=Solo lama
+1000169=Solo fresa
+1000170=Solo fresa
+1000171=Solo sega a catena
+1000172=Solo sega a catena
+1000173=Fresa disponibile per lavorare la superficie di taglio della mortasa
+1000174=Fresa disponibile per lavorare la superficie di taglio della mortasa
+1000175=Fresa disponibile per lavorare la mortasa a coda di rondine
+1000176=Fresa disponibile per lavorare la mortasa a coda di rondine
+1000177=Sovramateriale sulla lunghezza della mortasa
+1000178=Sovramateriale sulla lunghezza della mortasa
+1000179=Sovramateriale sulla larghezza della mortasa
+1000180=Sovramateriale sulla larghezza della mortasa
+1000181=Strategia di taglio
+1000182=Strategia di taglio
+1000183=Automatico
+1000184=Automatico
+1000185=Solo lama
+1000186=Solo lama
+1000187=Solo fresa
+1000188=Solo fresa
+1000189=Solo sega a catena
+1000190=Solo sega a catena
+1000191=Fresa disponibile per lavorare la superficie di taglio della mortasa
+1000192=Fresa disponibile per lavorare la superficie di taglio della mortasa
+1000193=Fresa disponibile per lavorare la mortasa
+1000194=Fresa disponibile per lavorare la mortasa
+1000195=Profondità dello smusso
+1000196=Profondità della fresa a V per eseguire smussi sugli spigoli di taglio
+1000197=Utilizza la strategia antischeggia
+1000198=La strategia applicherà tagli di lama sullo spigolo per evitare scheggiature del legno
+1000199=Fresa disponibile per lavorare il profilo
+1000200=Fresa disponibile per lavorare il profilo
+1000201=Antischeggia con lama
+1000202=Utilizza la lama come antischeggia nel caso in cui la geometria non sia passante
+1000203=Estendi dopo la coda
+1000204=L'automatismo considera questa lunghezza come lavorabile. Questo significa che si accetta di danneggiare il pezzo successivo nella barra
+1000205=Pulisci il raggio con la fresa
+1000206=Pulisci il raggio con la fresa
+1000207=Offset di fresatura dal lato
+1000208=Offset di fresatura dal lato
+1000209=Danneggia il pezzo successivo
+1000210=Questa opzione consente di decidere come considerare il pezzo successivo nella barra. Il software calcola specifici ingressi/uscite per rispettare il parametro. Questo parametro può variare il tempo di lavorazione
+1000211=Non danneggiare mai
+1000212=Non danneggiare mai
+1000213=Danneggia solo se grezzo
+1000214=Danneggia solo se grezzo
+1000215=Può danneggiare
+1000216=Può danneggiare
+1000217=Tolleranza sul diametro
+1000218=Tolleranza sul diametro
+1000219=Profondità del preforo
+1000220=Profondità del preforo
+1000221=Modalità di foratura
+1000222=Modalità di foratura
+1000223=Automatico
+1000224=Automatico
+1000225=Lavorazione preferita da un solo lato
+1000226=Lavorazione preferita da un solo lato
+1000227=Forza la lavorazione da due lati
+1000228=Forza la lavorazione da due lati
+1000229=Lista delle punte disponibili
+1000230=Lista delle punte disponibili
+1000231=Estendi dopo la coda
+1000232=L'automatismo considera questa lunghezza come lavorabile. Questo significa che si accetta di danneggiare il pezzo successivo nella barra
+1000233=Danneggia il pezzo successivo
+1000234=Questa opzione consente di decidere come considerare il pezzo successivo nella barra. Il software calcola specifici ingressi/uscite per rispettare il parametro. Questo parametro può variare il tempo di lavorazione
+1000235=Non danneggiare mai
+1000236=Non danneggiare mai
+1000237=Danneggia solo se grezzo
+1000238=Danneggia solo se grezzo
+1000239=Può danneggiare
+1000240=Può danneggiare
+1000241=Strategia del mezzolegno di colmo
+1000242=Strategia del mezzolegno di colmo
+1000243=Automatico
+1000244=Automatico
+1000245=Utilizza la lama
+1000246=Utilizza la lama
+1000247=Utilizza la fresa
+1000248=Utilizza la fresa
+1000249=Tolleranza sul diametro
+1000250=Tolleranza sul diametro
+1000251=Utilizza la fresa come una punta
+1000252=Ammetti l'uso della fresa come una punta da foratura
+1000253=Esegui solo il contorno
+1000254=Esegui comunque il contorno, anche se il foro è più grande del diametro dell'utensile
+1000255=Modalità di foratura
+1000256=Modalità di foratura
+1000257=Automatico
+1000258=Automatico
+1000259=Lavorazione preferita da un solo lato
+1000260=Lavorazione preferita da un solo lato
+1000261=Forza la lavorazione da due lati
+1000262=Forza la lavorazione da due lati
+1000263=Fresa disponibile per lavorare i fori
+1000264=Fresa disponibile per lavorare i fori
+1000265=Profondità di lavorazione
+1000266=Profondità di lavorazione
+1000267=Fresa disponibile per lavorare marcature e testi
+1000268=Fresa disponibile per lavorare marcature e testi
+1000269=Strategia di marcatura
+1000270=Strategia di marcatura
+1000271=Automatico
+1000272=Automatico
+1000273=Solo penna
+1000274=Solo penna
+1000275=Solo fresa a V
+1000276=Solo fresa a V
+1000277=Profondità dello smusso
+1000278=Profondità della fresa a V per eseguire smussi sugli spigoli di taglio
+1000279=Solo smusso
+1000280=Esegui solo lo smusso, nessuna altra lavorazione
+1000281=Sovramateriale
+1000282=Sovramateriale
+1000283=Raggio massimo rimasto sugli spigoli
+1000284=Limite del raggio lasciato dall'utensile ad ogni spigolo della feature
+1000285=Esegui il taglio per rimuovere materiale
+1000286=Esegui il taglio per rimuovere materiale
+1000287=Forza il testimone
+1000288=Abilita il parametro per forzare il software a lasciare un testimone per sostenere il pezzo
+1000289=Larghezza del testimone
+1000290=Larghezza del testimone nel caso in cui sia previsto dalla lavorazione
+1000291=Strategia di taglio
+1000292=Strategia di taglio
+1000293=Automatico
+1000294=Automatico
+1000295=Nessuna lavorazione
+1000296=Nessuna lavorazione
+1000297=Forza lama
+1000298=Forza lama
+1000299=Forza fresa
+1000300=Forza fresa
+1000301=Fresa disponibile per lavorare il profilo
+1000302=Fresa disponibile per lavorare il profilo
+1000303=Profondità dello smusso
+1000304=Profondità della fresa a V per eseguire smussi sugli spigoli di taglio
+1000305=Forza l'uso della sega a catena
+1000306=Forza l'uso della sega a catena
+1000307=Forza l'aggiunta di pretagli
+1000308=Autocam applicherà una lavorazione sullo zero teorico per evitare collisioni se la lunghezza teorica del pezzo non corrisponde alla lunghezza reale
+1000309=Finisci con la fresa
+1000310=Utilizza una fresa per rifinire la superficie se tagliata con la sega a catena
+1000311=Profondità dello smusso
+1000312=Profondità della fresa a V per eseguire smussi sugli spigoli di taglio
+1000313=Forza l'uso della sega a catena
+1000314=Forza l'uso della sega a catena
+1000315=Forza l'aggiunta di pretagli
+1000316=Autocam applicherà una lavorazione sullo zero teorico per evitare collisioni se la lunghezza teorica del pezzo non corrisponde alla lunghezza reale
+1000317=Finisci con la fresa
+1000318=Utilizza una fresa per rifinire la superficie se tagliata con la sega a catena
+// ----- End -----

Messages/EgalTechNld.txt

@@ -0,0 +1,322 @@
+// Message File EgalTech Dutch  2026/06/23
+0=NLD
+// ----- BeamNew -----
+1000001=Ladevolgorde van het onderdeel
+1000002=Ladevolgorde van het onderdeel
+1000003=Laadpositie vanaf BTL, geen voorrotatie
+1000004=Laadpositie vanaf BTL, geen voorrotatie
+1000005=Bepaal de beste laadpositie uit 0° en 180°
+1000006=Bepaal de beste laadpositie uit 0° en 180°
+1000007=Bepaal de beste laadpositie bij elke rotatie van het onderdeel
+1000008=Bepaal de beste laadpositie bij elke rotatie van het onderdeel
+1000009=Omkeren van het onderdeel toestaan
+1000010=Omkeren van het onderdeel toestaan
+1000011=Materiaaloptimalisatie in nesting inschakelen (rotatie van onderdeel uitgeschakeld)
+1000012=Materiaaloptimalisatie in nesting inschakelen (rotatie van onderdeel uitgeschakeld)
+1000013=Acceptatie van rotatie van het onderdeel
+1000014=Acceptatie van het roteren van het onderdeel tussen bewerkingsstappen
+1000015=Rotatie niet toegestaan
+1000016=Rotatie niet toegestaan
+1000017=Rotatie alleen toegestaan indien strikt noodzakelijk
+1000018=Rotatie alleen toegestaan indien strikt noodzakelijk
+1000019=Rotatie eenvoudig acceptabel / geen beperking
+1000020=Rotatie eenvoudig acceptabel / geen beperking
+1000021=Bewerkingsstrategie
+1000022=Bewerkingsstrategie
+1000023=Kwaliteit en tijd hebben gelijke prioriteit
+1000024=Kwaliteit en tijd hebben gelijke prioriteit
+1000025=Snelste
+1000026=Voorkeur geven aan de snelste strategieën
+1000027=Hoge kwaliteit
+1000028=Voorkeur geven aan hoogwaardige strategieën
+1000029=Ordeningsregels
+1000030=De eerste complete strategie in de lijst wordt gekozen; geen intelligente selectie
+1000031=Max. aantal herbewerkingscycli
+1000032=Max. aantal herbewerkingscycli
+1000033=Gebruik de volledige bladdiameter om het pad te verkorten
+1000034=Gebruik de volledige bladdiameter om het pad te verkorten
+1000035=Maximale lengte voor vallend afval
+1000036=Maximale lengte voor vallend afval
+1000037=Maximaal volume voor vallend afval
+1000038=Maximaal volume voor vallend afval
+1000039=Maximale afmeting van de blokjes
+1000040=Maximale afmeting van de blokjes
+1000041=Overmaat op de penlengte
+1000042=Overmaat op de penlengte
+1000043=Overmaat op de penbreedte
+1000044=Overmaat op de penbreedte
+1000045=Maximaal aantal freesgangen
+1000046=Maximaal aantal freesgangen. Als er meer gangen vereist zijn, wordt er uitkameren/uitfrezen uitgevoerd
+1000047=Zwaluwstaartgereedschap gebruiken voor uitfrezen
+1000048=Zwaluwstaartgereedschap gebruiken voor uitfrezen
+1000049=Snijstrategie
+1000050=Snijstrategie
+1000051=Automatisch
+1000052=Automatisch
+1000053=Alleen zaagblad
+1000054=Alleen zaagblad
+1000055=Alleen frees
+1000056=Alleen frees
+1000057=Alleen kettingzaag
+1000058=Alleen kettingzaag
+1000059=Beschikbare frees om het snijvlak van de pen te bewerken
+1000060=Beschikbare frees om het snijvlak van the pen te bewerken
+1000061=Beschikbare frees om de zwaluwstaartpen te bewerken
+1000062=Beschikbare frees om de zwaluwstaartpen te bewerken
+1000063=Maximale hoekradius achtergelaten op hoeken
+1000064=Radiuslimiet achtergelaten door het gereedschap bij elke binnenhoek van de feature
+1000065=Anti-splinterstrategie gebruiken
+1000066=De strategie past zaagsneden toe op de hoek om houtsplinters te voorkomen
+1000067=Verlengen na de staart
+1000068=Het automatisme beschouwt deze lengte als bewerkbaar. Dit betekent dat u accepteert dat het volgende onderdeel in de balk beschadigd kan raken
+1000069=Minimale benaderingsafstand op open zijden
+1000070=Minimale benaderingsafstand op open zijden
+1000071=Beschikbare frees voor het uitdiepen/uitfrezen van de feature
+1000072=Beschikbare frees voor het uitdiepen/uitfrezen van de feature
+1000073=Afwerken met kettingzaag indien nodig
+1000074=Afwerken met kettingzaag indien nodig
+1000075=Verlengen na de staart
+1000076=Het automatisme beschouwt deze lengte als bewerkbaar. Dit betekent dat u accepteert dat het volgende onderdeel in de balk beschadigd kan raken
+1000077=Schulpzaagblad forceren
+1000078=Forceer het gebruik van een schulpzaagblad, ontworpen voor zaagsneden parallel aan de houtnerf
+1000079=Niet voltooien als de uitloopradius van het zaagblad achterblijft
+1000080=Als de parameter actief is, beschouwt het automatisme de feature als - niet voltooid - als de uitloopradius van het zaagblad achterblijft
+1000081=Kettingzaag in zig-zag-modus gebruiken
+1000082=Schakel deze parameter in om de zig-zag-beweging voor de kettingzaagbewerking in te stellen. Deactiveer deze om de one-way-beweging te gebruiken.
+1000083=Sorteren per segment
+1000084=Sorteer de bewerkingen op basis van het onderdeelsegment waarin de bewerking is ingevoegd
+1000085=Volgend onderdeel beschadigen
+1000086=Met deze optie kunt u beslissen hoe u het volgende onderdeel in de balk beschouwt. De software berekent specifieke in- en uitlopen om de parameter te respecteren. Deze parameter kan de bewerkingstijd beïnvloeden
+1000087=Nooit beschadigen
+1000088=Nooit beschadigen
+1000089=Alleen beschadigen als het onbewerkt hout betreft
+1000090=Alleen beschadigen als het onbewerkt hout betreft
+1000091=Mag beschadigen
+1000092=Mag beschadigen
+1000093=Kettingzaag in zig-zag-modus gebruiken
+1000094=Schakel deze parameter in om de zig-zag-beweging voor de kettingzaagbewerking in te stellen. Deactiveer deze om de one-way-beweging te gebruiken.
+1000095=Verlengen na de staart
+1000096=Het automatisme beschouwt deze lengte als bewerkbaar. Dit betekent dat u accepteert dat het volgende onderdeel in de balk beschadigd kan raken
+1000097=Volgend onderdeel beschadigen
+1000098=Met deze optie kunt u beslissen hoe u het volgende onderdeel in de balk beschouwt. De software berekent specifieke in- en uitlopen om de parameter te respecteren. Deze parameter kan de bewerkingstijd beïnvloeden
+1000099=Nooit beschadigen
+1000100=Nooit beschadigen
+1000101=Alleen beschadigen als het onbewerkt hout betreft
+1000102=Alleen beschadigen als het onbewerkt hout betreft
+1000103=Mag beschadigen
+1000104=Mag beschadigen
+1000105=Schulpzaagblad forceren
+1000106=Forceer het gebruik van een schulpzaagblad, ontworpen voor zaagsneden parallel aan de houtnerf
+1000107=Verlengen na de staart
+1000108=Het automatisme beschouwt deze lengte als bewerkbaar. Dit betekent dat u accepteert dat het volgende onderdeel in de balk beschadigd kan raken
+1000109=Volgend onderdeel beschadigen
+1000110=Met deze optie kunt u beslissen hoe u het volgende onderdeel in de balk beschouwt. De software berekent specifieke in- en uitlopen om de parameter te respecteren. Deze parameter kan de bewerkingstijd beïnvloeden
+1000111=Nooit beschadigen
+1000112=Nooit beschadigen
+1000113=Alleen beschadigen als het onbewerkt hout betreft
+1000114=Alleen beschadigen als het onbewerkt hout betreft
+1000115=Mag beschadigen
+1000116=Mag beschadigen
+1000117=Zaagstrategie
+1000118=Zaagstrategie
+1000119=Automatisch
+1000120=Automatisch
+1000121=Kortafval afvoeren
+1000122=Kortafval afvoeren
+1000123=Kortafval verbonden houden
+1000124=Kortafval verbonden houden
+1000125=Opdelen in blokjes uitschakelen
+1000126=Opdelen in blokjes uitschakelen
+1000127=Prioriteit geven aan bewerkingssnelheid boven kwaliteit
+1000128=Prioriteit geven aan bewerkingssnelheid boven kwaliteit
+1000129=Breedte van de verbindingsstrip
+1000130=In het geval dat het afval vastgehecht blijft, is dit de breedteafmeting van de verbindingsstrip
+1000131=Uitloopradius van zaagblad reinigen met frees
+1000132=Uitloopradius van zaagblad reinigen met frees
+1000133=Freesoffset vanaf de zijde
+1000134=Freesoffset vanaf de zijde
+1000135=Overmaat op de penlengte
+1000136=Overmaat op de penlengte
+1000137=Overmaat op de penbreedte
+1000138=Overmaat op de penbreedte
+1000139=Maximum aantal freesgangen
+1000140=Maximum aantal freesgangen. Als er meer gangen vereist zijn, wordt er uitfrezen/uitkameren uitgevoerd
+1000141=Snijstrategie
+1000142=Snijstrategie
+1000143=Automatisch
+1000144=Automatisch
+1000145=Alleen zaagblad
+1000146=Alleen zaagblad
+1000147=Alleen frees
+1000148=Alleen frees
+1000149=Alleen kettingzaag
+1000150=Alleen kettingzaag
+1000151=Beschikbare frees om de pen te bewerken
+1000152=Beschikbare frees om de pen te bewerken
+1000153=Overmaat op de gatlengte
+1000154=Overmaat op de gatlengte
+1000155=Overmaat op de gatbreedte
+1000156=Overmaat op de gatbreedte
+1000157=Maximum aantal freesgangen
+1000158=Maximum aantal freesgangen. Als er meer gangen vereist zijn, wordt er uitfrezen/uitkameren uitgevoerd
+1000159=Zwaluwstaartgereedschap gebruiken bij uitfrezen
+1000160=Zwaluwstaartgereedschap gebruiken bij uitfrezen
+1000161=Anti-splintertoevoeging toepassen
+1000162=Anti-splintertoevoeging toepassen
+1000163=Snijstrategie
+1000164=Snijstrategie
+1000165=Automatisch
+1000166=Automatisch
+1000167=Alleen zaagblad
+1000168=Alleen zaagblad
+1000169=Alleen frees
+1000170=Alleen frees
+1000171=Alleen kettingzaag
+1000172=Alleen kettingzaag
+1000173=Beschikbare frees om het snijvlak van het gat te bewerken
+1000174=Beschikbare frees om het snijvlak van het gat te bewerken
+1000175=Beschikbare frees om het zwaluwstaartgat te frezen
+1000176=Beschikbare frees om het zwaluwstaartgat te frezen
+1000177=Overmaat op de gatlengte
+1000178=Overmaat op de gatlengte
+1000179=Overmaat op de gatbreedte
+1000180=Overmaat op de gatbreedte
+1000181=Snijstrategie
+1000182=Snijstrategie
+1000183=Automatisch
+1000184=Automatisch
+1000185=Alleen zaagblad
+1000186=Alleen zaagblad
+1000187=Alleen frees
+1000188=Alleen frees
+1000189=Alleen kettingzaag
+1000190=Alleen kettingzaag
+1000191=Beschikbare frees om het snijvlak van het gat te bewerken
+1000192=Beschikbare frees om het snijvlak van het gat te bewerken
+1000193=Beschikbare frees om het gat te frezen
+1000194=Beschikbare frees om het gat te frezen
+1000195=Diepte van de afschuining
+1000196=Diepte van de V-frees om afschuiningen op snijkanten uit te voeren
+1000197=Anti-splinterstrategie gebruiken
+1000198=De strategie past zaagsneden toe op de hoek om houtsplinters te voorkomen
+1000199=Beschikbare frees om het profiel te bewerken
+1000200=Beschikbare frees om het profiel te bewerken
+1000201=Anti-splinterfunctie via zaagblad
+1000202=Gebruik het zaagblad als anti-splintervoorziening indien de geometrie niet doorgaand is
+1000203=Verlengen na de staart
+1000204=Het automatisme beschouwt deze lengte als bewerkbaar. Dit betekent dat u accepteert dat het volgende onderdeel in de balk beschadigd kan raken
+1000205=Uitloopradius reinigen met frees
+1000206=Uitloopradius reinigen met frees
+1000207=Freesoffset vanaf de zijde
+1000208=Freesoffset vanaf de zijde
+1000209=Volgend onderdeel beschadigen
+1000210=Met deze optie kunt u beslissen hoe u het volgende onderdeel in de balk beschouwt. De software berekent specifieke in- en uitlopen om de parameter te respecteren. Deze parameter kan de bewerkingstijd beïnvloeden
+1000211=Nooit beschadigen
+1000212=Nooit beschadigen
+1000213=Alleen beschadigen als het onbewerkt hout betreft
+1000214=Alleen beschadigen als het onbewerkt hout betreft
+1000215=Mag beschadigen
+1000216=Mag beschadigen
+1000217=Tolerantie op diameter
+1000218=Tolerantie op diameter
+1000219=Diepte van het voorgat
+1000220=Diepte van het voorgat
+1000221=Boormodus
+1000222=Boormodus
+1000223=Automatisch
+1000224=Automatisch
+1000225=Voorkeursbewerking vanaf slechts één zijde
+1000226=Voorkeursbewerking vanaf slechts één zijde
+1000227=Bewerking vanaf beide zijden forceren
+1000228=Bewerking vanaf beide zijden forceren
+1000229=Lijst met beschikbare boren
+1000230=Lijst met beschikbare boren
+1000231=Verlengen na de staart
+1000232=Het automatisme beschouwt deze lengte als bewerkbaar. Dit betekent dat u accepteert dat het volgende onderdeel in de balk beschadigd kan raken
+1000233=Volgend onderdeel beschadigen
+1000234=Met deze optie kunt u beslissen hoe u het volgende onderdeel in de balk beschouwt. De software berekent specifieke in- en uitlopen om de parameter te respecteren. Deze parameter kan de bewerkingstijd beïnvloeden
+1000235=Nooit beschadigen
+1000236=Nooit beschadigen
+1000237=Alleen beschadigen als het onbewerkt hout betreft
+1000238=Alleen beschadigen als het onbewerkt hout betreft
+1000239=Mag beschadigen
+1000240=Mag beschadigen
+1000241=Borstverjonging zaag- en freesstrategie
+1000242=Borstverjonging zaag- en freesstrategie
+1000243=Automatisch
+1000244=Automatisch
+1000245=Zaagblad gebruiken
+1000246=Zaagblad gebruiken
+1000247=Frees gebruiken
+1000248=Frees gebruiken
+1000249=Tolerantie op diameter
+1000250=Tolerantie op diameter
+1000251=Frees gebruiken als boor
+1000252=Toestaan dat de frees axiaal als boor wordt ingezet
+1000253=Alleen contour frezen
+1000254=Contour sowieso frezen, zelfs wanneer het gat groter is dan de gereedschapsdiameter
+1000255=Boormodus via frezen
+1000256=Boormodus via frezen
+1000257=Automatisch
+1000258=Automatisch
+1000259=Voorkeursbewerking vanaf slechts één zijde
+1000260=Voorkeursbewerking vanaf slechts één zijde
+1000261=Bewerking vanaf beide zijden forceren
+1000262=Bewerking vanaf beide zijden forceren
+1000263=Beschikbare frezen om gaten te bewerken
+1000264=Beschikbare frezen om gaten te bewerken
+1000265=Bewerkingsdiepte
+1000266=Bewerkingsdiepte
+1000267=Beschikbare frees voor markeringen en tekst
+1000268=Beschikbare frees voor markeringen en tekst
+1000269=Markeerstrategie
+1000270=Markeerstrategie
+1000271=Automatisch
+1000272=Automatisch
+1000273=Alleen markeerpen
+1000274=Alleen markeerpen
+1000275=Alleen V-frees
+1000276=Alleen V-frees
+1000277=Diepte van de afschuining
+1000278=Diepte van de V-frees om afschuiningen op snijkanten uit te voeren
+1000279=Alleen afschuining frezen
+1000280=Alleen de afschuining uitvoeren, geen andere bewerkingen
+1000281=Overmaat
+1000282=Overmaat
+1000283=Maximale hoekradius achtergelaten op hoeken
+1000284=Radiuslimiet achtergelaten door het gereedschap bij elke binnenhoek van de feature
+1000285=Zaagsnede uitvoeren om materiaal te verwijderen
+1000286=Zaagsnede uitvoeren om materiaal te verwijderen
+1000287=Snoei- / steunstrip forceren
+1000288=Activeer deze parameter om de software te verplichten een reststrip te laten staan om het onderdeel te ondersteunen
+1000289=Breedte van de steunstrip
+1000290=Breedte van de strip in het geval dat deze door de bewerking is voorzien
+1000291=Kopsnijstrategie
+1000292=Kopsnijstrategie
+1000293=Automatisch
+1000294=Automatisch
+1000295=Geen bewerking
+1000296=Geen bewerking
+1000297=Zaagblad geforceerd
+1000298=Zaagblad geforceerd
+1000299=Frees geforceerd
+1000300=Frees geforceerd
+1000301=Beschikbare frees om het kops profiel te bewerken
+1000302=Beschikbare frees om het kops profiel te bewerken
+1000303=Diepte van de afschuining
+1000304=Diepte van de V-frees om afschuiningen op snijkanten uit te voeren
+1000305=Gebruik van kettingzaag forceren
+1000306=Gebruik van kettingzaag forceren
+1000307=PreCuts (Voorsneden) forceren
+1000308=Autocam past een bewerking toe op het theoretische nulpunt om botsingen te voorkomen als de theoretische lengte niet overeenkomt met de werkelijke lengte
+1000309=Afwerken met frees
+1000310=Gebruik een frees om het oppervlak na te bewerken als dit met de kettingzaag is gespleten
+1000311=Diepte van de afschuining
+1000312=Diepte van de V-frees om afschuiningen op snijkanten uit te voeren
+1000313=Gebruik van kettingzaag forceren
+1000314=Gebruik van kettingzaag forceren
+1000315=PreCuts (Voorsneden) forceren
+1000316=Autocam past een bewerking toe op het theoretische nulpunt om botsingen te voorkomen als de theoretische lengte niet overeenkomt met de werkelijke lengte
+1000317=Afwerken met frees
+1000318=Gebruik een frees om het oppervlak na te bewerken als dit met de kettingzaag is gespleten
+// ----- End -----

NestProcessOld.lua

@@ -0,0 +1,477 @@
+-- BeamNestProcess.lua by Egaltech s.r.l. 2023/01/15
+-- Gestione nesting automatico travi
+-- 2022/10/05 Piccole modifiche per far funzionare correttamente i compilati.
+-- 2022/10/06 Corretto bug che moltiplicava i pezzi se erano presenti più grezzi della stessa sezione.
+-- 2023/01/15 Piccole correzioni.
+
+-- Intestazioni
+require( 'EgtBase')
+_ENV = EgtProtectGlobal()
+EgtEnableDebug( false)
+
+-- Per test
+--NEST = {}
+--NEST.FILE = 'c:\\TechnoEssetre7\\EgtData\\Prods\\0010\\Bar_10_1.btl'
+--NEST.MACHINE = 'Essetre-90480019_MW'
+--NEST.FLAG = 3
+
+local sLog = ' +++ BeamNestProcess : ' .. NEST.FILE .. ', ' .. NEST.MACHINE .. ', ' .. LEN[1]
+EgtOutLog( sLog)
+
+-- flag per abilitare statistiche in log
+local bLogStat = false
+
+-- Cancello file di log specifico
+local sLogFile = EgtChangePathExtension( NEST.FILE, '.txt')
+EgtEraseFile( sLogFile) 
+
+-- Funzioni per scrittura su file di log specifico
+local function WriteErrToLogFile( nErr, sMsg, nRot, nCutId, nTaskId)
+   local hFile = io.open( sLogFile, 'a')
+   hFile:write( 'ERR=' .. tostring( nErr) .. '\n')
+   hFile:write( sMsg .. '\n')
+   hFile:write( 'ROT=' .. tostring( nRot or 0) .. '\n')
+   hFile:write( 'CUTID=' .. tostring( nCutId or 0) .. '\n')
+   hFile:write( 'TASKID=' .. tostring( nTaskId or 0) .. '\n')
+   hFile:close()
+end
+
+local function WriteTimeToLogFile( dTime)
+   local hFile = io.open( sLogFile, 'a')
+   hFile:write( 'TIME=' .. EgtNumToString( dTime) .. '\n')
+   hFile:close()
+end
+
+-- Funzione per gestire visualizzazione dopo errore
+local function PostErrView( nErr, sMsg)
+   if nErr ~= 0 and ( NEST.FLAG == 1 or NEST.FLAG == 2 or NEST.FLAG == 5) then
+      EgtSetView( SCE_VD.ISO_SW, false)
+      EgtZoom( SCE_ZM.ALL)
+      EgtOutBox( sMsg, 'BatchProcess (err=' .. tostring( nErr) .. ')', 'ERRORS')
+   end
+end
+
+-- Funzione per gestire visualizzazione dopo warning
+local function PostWarnView( nWarn, sMsg)
+   if nWarn ~= 0 and ( NEST.FLAG == 1 or NEST.FLAG == 2 or NEST.FLAG == 5) then
+      EgtSetView( SCE_VD.ISO_SW, false)
+      EgtZoom( SCE_ZM.ALL)
+      EgtOutBox( sMsg, 'BatchProcess (wrn=' .. tostring( nWarn) .. ')', 'WARNINGS')
+   end
+end
+
+-- Funzione per aggiornare dati ausiliari
+local function UpdateAuxData( sAuxFile)
+   local bModif = false
+   -- Se definito LOAD90, aggiorno
+   local sLoad90 = EgtGetStringFromIni( 'AuxData', 'LOAD90', '', sAuxFile) 
+   if sLoad90 ~= '' then
+      local BtlInfoId = EgtGetFirstNameInGroup( GDB_ID.ROOT, 'BtlInfo') or GDB_ID.NULL
+      EgtSetInfo( BtlInfoId, 'LOAD90', sLoad90)
+      bModif = true
+   end
+   return bModif
+end
+
+local function PartsToFill( Parts)
+   local nToFill = 0
+   for i = 1, #Parts do
+      if Parts[i].Cnt > 0 then
+         nToFill = nToFill + Parts[i].Cnt
+      end
+   end
+   return nToFill
+end
+
+local function ExecMaximumFilling( Raw, Parts)
+   -- Inizializzo maximum filler
+   EgtMaxFillerStart()
+   -- Inserisco i pezzi
+   for i = 1, #Parts do
+      EgtMaxFillerAddPart( i, Parts[i].Len, Parts[i].DispLen or Parts[i].Len, Parts[i].Cnt or 1)
+   end
+   -- Eseguo l'ottimizzazione
+   EgtMaxFillerCompute( Raw.LenToFill, Raw.StartGap, Raw.MidGap, Raw.EndGap, Raw.SortType)
+   -- Recupero i risultati
+   local nFilledParts, nDiffParts, dTotFillRatio = EgtMaxFillerGetResults()
+   local OneRes = {}
+   for i = 0, nDiffParts - 1 do
+      local nPartId, nCount = EgtMaxFillerGetOneResult( i)
+      table.insert( OneRes, { Id=nPartId, Count=nCount})
+   end
+   --return { FilledParts=nFilledParts, DiffParts=nDiffParts, FillRatio=dTotFillRatio, Time=dTime, Data=OneRes}
+   return { FilledParts=nFilledParts, DiffParts=nDiffParts, FillRatio=dTotFillRatio, Data=OneRes}
+end
+
+-- Funzione per trovare nome MachGroup
+local function NewMachGroupName()
+   local nMachGroupId = EgtGetFirstMachGroup()
+   if not nMachGroupId then return 1 end
+   local nMaxMachGroup = 0
+   while nMachGroupId do
+      sMachGroupName = EgtGetMachGroupName(nMachGroupId)
+      local nMachGroupName = tonumber(sMachGroupName)
+      if nMachGroupName > nMaxMachGroup then
+         nMaxMachGroup = nMachGroupName
+      end
+      nMachGroupId = EgtGetNextMachGroup(nMachGroupId)
+   end
+   return nMaxMachGroup + 1
+end
+
+local function TotRawCount(Raws)
+   local nTotRaws = 0
+   for RawIndex = 1, #Raws do
+      nTotRaws = nTotRaws + Raws[RawIndex].Count
+   end
+   return nTotRaws
+end
+
+local function TotPartLen(Parts)
+   local nTotPartLen = 0
+   for PartIndex = 1, #Parts do
+      nTotPartLen = nTotPartLen + ( Parts[PartIndex].Len * Parts[PartIndex].Cnt)
+   end
+   return nTotPartLen
+end
+
+-- Imposto direttorio libreria specializzata per Travi
+EgtAddToPackagePath( NEST.BASEDIR .. '\\LuaLibs\\?.lua')
+
+-- Imposto la macchina corrente e verifico sia abilitata per la lavorazione delle Travi
+EgtSetCurrMachine( NEST.MACHINE)
+local sMachDir = EgtGetCurrMachineDir()
+if not EgtExistsFile( sMachDir .. '\\Beam\\BeamData.lua') then
+   NEST.ERR = 12
+   NEST.MSG = 'Error not configured for beam machine : ' .. sMachine
+   WriteErrToLogFile( NEST.ERR, NEST.MSG)
+   PostErrView( NEST.ERR, NEST.MSG)
+   return
+end
+
+-- Elimino direttori altre macchine e imposto direttorio macchina corrente per ricerca librerie
+EgtRemoveBaseMachineDirFromPackagePath()
+EgtAddToPackagePath( sMachDir .. '\\Beam\\?.lua')
+
+-- Inizializzo contatori errori e avvisi
+local nErrCnt = 0
+local nWarnCnt = 0
+
+-- Grezzi
+local Raws = {}
+-- creo tabella dei grezzi
+for nIndex, nLen in pairs( LEN) do
+   Raws[tonumber(nIndex)] = {LenToFill = nLen, StartGap = NEST.STARTOFFSET, MidGap = NEST.OFFSET, EndGap = 0, SortType = -1}
+end
+for nIndex, nQty in pairs( QTY) do
+   Raws[tonumber(nIndex)].Count = nQty
+end
+-- cerco il grezzo con la lunghezza maggiore, epurata dello start gap
+local maxRawLenToFillNoStartGap = 0
+for RawIndex = 1, #Raws do
+   if Raws[RawIndex].Count > 0 then
+      maxRawLenToFillNoStartGap = max( maxRawLenToFillNoStartGap, Raws[RawIndex].LenToFill - Raws[RawIndex].StartGap)
+   end
+end
+
+-- Pezzi
+local Parts = {}
+-- ciclo su pezzi per aggiungerli al nesting
+local dTotLen = 0
+for nPartId, nCount in pairs( PART) do
+   -- recupero lunghezza pezzo
+   local Len = EgtGetInfo( nPartId, "L", 'd')
+   local DispLen = EgtIf( Len <= 1000, 2000, 0) --EgtIf( Len <= 2000, max( 2000, 6000 - Len), 0)
+   -- aggiungo il pezzo solo se ci sta nel grezzo più lungo a disposizione
+   if Len < maxRawLenToFillNoStartGap then
+      for nCntIndex = 1 , nCount do
+         table.insert( Parts, {Id = nPartId, Len = Len, DispLen = DispLen, Cnt = 1})
+         dTotLen = dTotLen + Len
+      end
+   end
+end
+
+-- lunghezza totale pezzi
+local dTotPartLen = TotPartLen( Parts)
+-- calcolo media delle barre necessarie
+local NeededRawsForType = {}
+for RawIndex = 1, #Raws do
+   NeededRawsForType[RawIndex] = min( ceil( dTotPartLen / Raws[RawIndex].LenToFill), Raws[RawIndex].Count)
+end
+local RawQtySum = 0
+for NeededRawIndex = 1, #NeededRawsForType do
+   RawQtySum = RawQtySum + NeededRawsForType[NeededRawIndex] 
+end
+local MediumRawQty = ceil( RawQtySum / #NeededRawsForType) 
+if MediumRawQty > 1 then
+   MediumRawQty = MediumRawQty - 1
+end
+
+-- lista dei risultati
+local ResultList = {}
+local BestResult = nil
+local BestResultIndex = nil
+-- riordino lista pezzi per lunghezza
+table.sort( Parts, function( B1, B2) return B1.Len < B2.Len end)
+
+local function NestSolutionByIndex( Index)
+   
+   -- creo copia lista raw
+   local TempRaws = {}
+   for TempRawIndex = 1, #Raws do
+      table.insert(TempRaws, {LenToFill = Raws[TempRawIndex].LenToFill, StartGap = Raws[TempRawIndex].StartGap, MidGap = Raws[TempRawIndex].MidGap, EndGap = Raws[TempRawIndex].EndGap, SortType = Raws[TempRawIndex].SortType, Count = Raws[TempRawIndex].Count})
+   end
+   
+   -- recupero pezzi corti
+   local ShortList = {}
+   local LongList = {}
+
+   for PartIndex = 1, #Parts do
+      if PartIndex <= Index then
+         table.insert( ShortList, Parts[PartIndex])
+      else
+         table.insert( LongList, Parts[PartIndex])
+      end
+      Parts[PartIndex].Cnt = 1
+   end
+   -- numero di pezzi piccoli per barra
+   local ShortCount = Index
+   local ShortForRaw = floor( ShortCount / MediumRawQty)
+   local ExtraShortForRaw = 0
+   if MediumRawQty > 0 then
+      ExtraShortForRaw = fmod( ShortCount, MediumRawQty)
+   end
+   -- creo lista pezzi corti singoli
+   local SingleShortList = {}
+   for ShortIndex = 1, #ShortList do
+      for ShortCount = 1, ShortList[ShortIndex].Cnt do
+         table.insert( SingleShortList, {Id = ShortList[ShortIndex].Id, Len = ShortList[ShortIndex].Len, DispLen = ShortList[ShortIndex].DispLen, Cnt = 1})
+      end
+   end 
+   -- li divido per le barre previste
+   local RawsShortList = {}
+   local RawIndex = 0
+   local ShortRawIndex = 0
+   for ShortIndex = 1, #SingleShortList do
+      if ShortRawIndex > 0 then
+         table.insert( RawsShortList[RawIndex], SingleShortList[ShortIndex])
+         ShortRawIndex = ShortRawIndex - 1
+      else
+         table.insert( RawsShortList, {SingleShortList[ShortIndex]})
+         RawIndex = RawIndex + 1
+         ShortRawIndex = ShortForRaw + EgtIf( RawIndex <= ExtraShortForRaw, 1, 0) - 1
+      end
+   end
+
+   -- Ciclo fino ad esaurimento pezzi o barre
+   local dTotPartInRawLen = 0
+   local nRawTot = 0
+   local dRawTotLen = 0
+   local dTime = 0
+   local nCycle = 1
+   local CurrResult = {}
+   while TotRawCount( TempRaws) > 0 and PartsToFill( Parts) > 0 do
+      
+      -- creo lista con pezzi lunghi e pezzi corti di questo Cycle
+      local PartsToNest = {}
+      for PartIndex = 1, #LongList do
+         table.insert( PartsToNest, LongList[PartIndex])
+      end
+      for CycleIndex = 1, #RawsShortList do
+         if CycleIndex <= nCycle then
+            for PartIndex = 1, #RawsShortList[CycleIndex] do
+               table.insert( PartsToNest, RawsShortList[CycleIndex][PartIndex])
+            end
+         end
+      end
+      
+      -- se non ci sono pezzi da nestare, esco
+      if PartsToFill( PartsToNest) <= 0 then
+         break
+      end
+      -- Eseguo ottimizzazione per ogni lunghezza di barra
+      local Results = {}
+      for RawIndex = 1, #TempRaws do
+         if TempRaws[RawIndex].Count > 0 then
+            Results[RawIndex] = ExecMaximumFilling( TempRaws[RawIndex], PartsToNest)
+         else
+            Results[RawIndex] = { FillRatio = 0.001, LenToFill = 1000, DiffParts = 0}
+         end
+      end
+      -- verifico quale e' quella con meno scarto
+      local nMinWasteRawIndex = GDB_ID.NULL
+      local dMinWaste = 100000
+      for ResultIndex = 1, #Results do
+         if Results[ResultIndex] then
+            local dWaste = (1 - Results[ResultIndex].FillRatio) * TempRaws[ResultIndex].LenToFill
+            if Results[ResultIndex].DiffParts > 0 and dWaste < dMinWaste then
+               dMinWaste = dWaste
+               nMinWasteRawIndex = ResultIndex
+            end
+         end
+      end
+      -- verifico se ci sono pezzi
+      if nMinWasteRawIndex > 0 and Results[nMinWasteRawIndex] and Results[nMinWasteRawIndex].DiffParts > 0 then
+         -- riporto barra e pezzi nel risultato corrente 
+         local CurrBar = { BarLen = TempRaws[nMinWasteRawIndex].LenToFill,  Parts = {}}
+         local CurrX = TempRaws[nMinWasteRawIndex].StartGap
+         local nInfoIndex = 1
+         for i = 1, Results[nMinWasteRawIndex].DiffParts do
+            local PartIndex = Results[nMinWasteRawIndex].Data[i].Id
+            local PartId = PartsToNest[PartIndex].Id
+            local dLen = PartsToNest[PartIndex].Len
+            for j = 1, Results[nMinWasteRawIndex].Data[i].Count do
+               -- creo pezzo copia
+               CurrPart = { Index = nInfoIndex, PartId = PartId, PosX = CurrX}
+               table.insert( CurrBar.Parts, CurrPart)
+               CurrX = CurrX + dLen + TempRaws[nMinWasteRawIndex].MidGap
+               nInfoIndex = nInfoIndex + 1
+            end
+         end
+         table.insert( CurrResult, CurrBar)
+         dTotPartInRawLen = dTotPartInRawLen + ( Results[nMinWasteRawIndex].FillRatio * TempRaws[nMinWasteRawIndex].LenToFill)
+         nRawTot = nRawTot + 1
+         dRawTotLen = dRawTotLen + TempRaws[nMinWasteRawIndex].LenToFill
+         -- Aggiorno per prossima iterazione
+         TempRaws[nMinWasteRawIndex].Count = TempRaws[nMinWasteRawIndex].Count - 1
+         for i = 1, Results[nMinWasteRawIndex].DiffParts do
+            local PartId = Results[nMinWasteRawIndex].Data[i].Id
+            PartsToNest[PartId].Cnt = PartsToNest[PartId].Cnt - Results[nMinWasteRawIndex].Data[i].Count
+         end
+      else
+         -- se non sono riuscito ad inserire alcun pezzo esco dal ciclo perche' non ci sono pezzi inseribili
+         break
+      end
+      nCycle = nCycle + 1
+   end
+   -- riporto risultato in lista
+   ResultList[Index] = dTotPartInRawLen
+   if not BestResult or not BestResultIndex or
+      ( dTotPartInRawLen > ResultList[BestResultIndex] + 0.02 or ( abs( dTotPartInRawLen - ResultList[BestResultIndex]) < 0.02 and dRawTotLen < BestResult.RawTotLen - 0.02)) then
+      BestResult = CurrResult
+      BestResult.RawTotLen = dRawTotLen
+      BestResultIndex = Index
+   end
+end
+
+local CycleCount = 0
+
+local MinTime = 10 + pow( 3, ceil( log10( #Parts)) - 1)
+if bLogStat then EgtOutLog('MinTime: ' .. MinTime ) end
+local MaxTime = 30 + pow( 7, ceil( log10( #Parts)) - 1)
+if bLogStat then EgtOutLog('MaxTime: ' .. MaxTime ) end
+local TargetRatio = 0.98
+local dTargetRatioLen = TargetRatio * dTotLen
+if bLogStat then EgtOutLog('TargetRatioLen: ' .. dTargetRatioLen ) end
+local CurrTime = 0
+
+local function NestSolutionFromSP( StartingPoint, OscillationStep)
+   -- ciclo sulle possibilita' da un punto di origine con uno step fisso
+   local CurrResultIndex = StartingPoint
+   NestSolutionByIndex( StartingPoint)
+   if OscillationStep == 0 then return end
+   local CycleIndex = 1
+   local nOutOfBoundary = 0
+   while nOutOfBoundary ~= 3 do
+      CurrTime = EgtStopCounter() / 1000
+      if bLogStat then EgtOutLog('CurrTime: ' .. CurrTime ) end
+      if bLogStat then EgtOutLog('BestRatio: ' .. dTotLen / BestResult.RawTotLen ) end
+      -- se e' passato il tempo massimo, o e' passato il tempo minimo, ha inserito tutti i pezzi e la percentuale di utilizzo del materiale e' maggiore della soglia
+      if CurrTime > MaxTime or ( CurrTime > MinTime and ResultList[BestResultIndex] > dTotLen - 0.1 and ( dTotLen / BestResult.RawTotLen ) >= TargetRatio) then 
+         if bLogStat then EgtOutLog('Brake') end
+         break
+      end
+      local bCurrOutOfBoundary = false
+      if CurrResultIndex < 0 then
+         bCurrOutOfBoundary = true
+         if nOutOfBoundary == 2 then
+            nOutOfBoundary = 3
+         else
+            nOutOfBoundary = 1
+         end
+      end
+      if CurrResultIndex > #Parts then
+         bCurrOutOfBoundary = true
+         if nOutOfBoundary == 1 then
+            nOutOfBoundary = 3
+         else
+            nOutOfBoundary = 2
+         end
+      end
+      if not bCurrOutOfBoundary and not ResultList[CurrResultIndex] then
+         NestSolutionByIndex( CurrResultIndex)
+         if bLogStat then EgtOutLog('CurrResultIndex: ' .. CurrResultIndex ) end
+         if bLogStat then EgtOutLog('Result: ' .. ResultList[CurrResultIndex]) end
+         CycleCount = CycleCount + 1
+      end
+      CurrResultIndex = StartingPoint + EgtIf( CycleIndex % 2 == 0, (CycleIndex / 2) * OscillationStep, -( ( CycleIndex + 1) / 2) * OscillationStep )
+      CycleIndex = CycleIndex + 1
+   end
+end
+   
+-- lancio calcolo
+EgtStartCounter()
+local StartingResult = floor( #Parts * 0.3)
+if bLogStat then EgtOutLog('StartingResult: ' .. StartingResult ) end
+--local Step = floor( #Parts / 10) * floor( log10( #Parts))
+local nDividendo = pow( 10, floor( log10( #Parts)) - 1)
+nDividendo = EgtIf( nDividendo ~= 1, nDividendo, 10)
+local Step = floor( #Parts / nDividendo) * floor( log10( #Parts))
+if bLogStat then EgtOutLog('Step: ' .. Step ) end
+NestSolutionFromSP( StartingResult, Step)
+if Step > 1 then
+   NestSolutionFromSP( StartingResult, 1)
+end
+
+-- creo gruppi di lavorazione per risultato
+for MachGroupIndex = 1, #BestResult do
+   local CurrMachGroup = BestResult[ MachGroupIndex]
+   -- creo gruppo di lavorazione
+   local MachGroupName = NewMachGroupName()
+   nMachGroup = EgtAddMachGroup( MachGroupName)
+   EgtSetInfo( nMachGroup, "BARLEN", CurrMachGroup.BarLen)
+   EgtSetInfo( nMachGroup, "MATERIAL", NEST.MATERIAL)
+   EgtSetInfo( nMachGroup, "AUTONEST", 1)
+   -- scrivo dati per variabili P di comunicazione con la macchina in gruppo di lavorazione
+   EgtSetInfo( nMachGroup, "PRODID", NEST.PRODID)
+   EgtSetInfo( nMachGroup, "PATTID", nMachGroup)
+   -- Disegno i pezzi
+   for i = 1, #CurrMachGroup.Parts do
+      local CurrPart = CurrMachGroup.Parts[ i]
+      -- creo pezzo copia
+      local nPartDuploId = EgtDuploNew( CurrPart.PartId)
+      EgtSetInfo( nMachGroup, "PART" .. CurrPart.Index, nPartDuploId .. "," .. CurrPart.PosX)
+   end
+end
+
+-- creo grezzi per ogni gruppo di lavorazione
+local nRawCnt = 0
+local nRawTot = ResultList[BestResultIndex]
+_G.BEAM = {}
+BEAM.FILE = NEST.FILE
+BEAM.MACHINE = NEST.MACHINE
+BEAM.FLAG = 6    -- CREATE_PANEL
+BEAM.BASEDIR = NEST.BASEDIR
+nMachGroup = EgtGetFirstMachGroup()
+while nMachGroup do
+   local nNextMachGroup = EgtGetNextMachGroup( nMachGroup)
+   EgtSetCurrMachGroup( nMachGroup)
+   if EgtGetInfo( nMachGroup, "AUTONEST",'i') == 1 then
+      EgtRemoveInfo( nMachGroup, "AUTONEST")
+      EgtSetInfo( nMachGroup, "UPDATEUI", 1)
+      local bOk, sErr = pcall( dofile, BEAM.BASEDIR .. "\\BatchProcessNew.lua")
+      if not bOk then
+         EgtOutLog( 'Error in BatchProcessNew.lua call (' .. ( sErr or '') ..')')
+      end
+      nRawCnt = nRawCnt + 1
+      -- aggiorno interfaccia
+      EgtProcessEvents( 200 + ( nRawCnt / nRawTot * 100), 0)
+   end
+   nMachGroup = nNextMachGroup
+end
+
+EgtResetCurrMachGroup()
+
+NEST.ERR = 0
+
+EgtOutLog( ' +++ BeamNestProcess completed')

Process.lua

@@ -131,6 +131,14 @@ local function MyProcessInputData()
       else
          PARTS[i].b3PartOriginal = b3Solid
       end
+      if BeamData.MAX_LENGTH and BeamData.MAX_LENGTH > 10 and b3Solid:getDimX() > BeamData.MAX_LENGTH then
+         local sOut = 'Lunghezza ('  .. EgtNumToString( b3Solid:getDimX(), 2) .. ') ' ..
+                      'oltre i limiti della macchina (' .. EgtNumToString( BeamData.MAX_LENGTH, 2) .. ') '
+         EgtOutLog( sOut)
+         EgtOutBox( sOut, 'Lavora Travi', 'WARNING')
+         EgtDraw()
+         return false
+      end
    end
    dRawW = PARTS[1].b3PartOriginal:getDimY()
    dRawH = PARTS[1].b3PartOriginal:getDimZ()
@@ -304,7 +312,7 @@ local function MyProcessFeatures()
 
    BeamExec.GetProcessings( PARTS, false)
    BeamExec.GetCombinationMatrix( PARTS, false)
-   BeamExec.ProcessMachinings( PARTS)
+   BeamExec.ProcessMachinings( PARTS, false)
    local nErrCnt = 0
    local nWarnCnt = 0
    local sOutput = ''

Strategies/AvailableStrategyList.json

@@ -392,7 +392,7 @@
       "TopologyList" : [
          {  "sName": "Feature",
             "sImage": "ConfigStrategy\\Chamfer.png",
-            "StrategyList" : [ ]
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010" } ]
          }
       ]
    },
@@ -688,7 +688,7 @@
       "TopologyList" : [
          {  "sName": "Feature",
             "sImage": "ConfigStrategy\\ScarfJoint.png",
-            "StrategyList" : [ ]
+            "StrategyList" : [ { "sStrategyId": "STR0009" }]
          }
       ]
    },

Strategies/GeneralParameters.json

@@ -1,4 +1,3 @@
-
 [
    {
       "nGroup": "PIECE LOADING",
@@ -7,6 +6,8 @@
       "sValue": "BTL_POSITION",
       "sDescriptionShort": "Part loading position",
       "sDescriptionLong": "",
+      "idDescriptionShortMsg": 1000001,
+      "idDescriptionLongMsg": 1000002,
       "sType": "combo",
       "sMinUserLevel": "1",
       "Choices": [
@@ -14,18 +15,24 @@
             "sValue": "BTL_POSITION",
             "sDescriptionShort": "Loading position from BTL, no pre-rotation",
             "sDescriptionLong": "",
+            "idDescriptionShortMsg": 1000003,
+            "idDescriptionLongMsg": 1000004,
             "sMessageId": ""
          },
          {
             "sValue": "STD_PRE_ROTATION",
             "sDescriptionShort": "Get Best loading position from 0° and 180°",
             "sDescriptionLong": "",
+            "idDescriptionShortMsg": 1000005,
+            "idDescriptionLongMsg": 1000006,
             "sMessageId": ""
          },
          {
             "sValue": "FULL_PRE_ROTATION",
             "sDescriptionShort": "Get Best loading position in each piece rotation",
             "sDescriptionLong": "",
+            "idDescriptionShortMsg": 1000007,
+            "idDescriptionLongMsg": 1000008,
             "sMessageId": ""
          }
       ]
@@ -37,17 +44,8 @@
       "sValue": "false",
       "sDescriptionShort": "Allow piece inversion",
       "sDescriptionLong": "",
-      "sType": "b",
-      "sMessageId": " ",
-      "sMinUserLevel": "1"
-   },
-   {
-      "nGroup": "PIECE LOADING",
-      "sName": "GEN_bTestAlternative",
-      "sNameNge": "TEST_ALTERNATIVE",
-      "sValue": "false",
-      "sDescriptionShort": "Enable the possibility to load the piece 90° turned",
-      "sDescriptionLong": "",
+      "idDescriptionShortMsg": 1000009,
+      "idDescriptionLongMsg": 1000010,
       "sType": "b",
       "sMessageId": " ",
       "sMinUserLevel": "1"
@@ -57,8 +55,10 @@
       "sName": "GEN_bGetAlternativesNesting2D",
       "sNameNge": "GET_ALTERNATIVES_NEST2D",
       "sValue": "false",
-      "sDescriptionShort": "Enable material optimization function in nesting",
+      "sDescriptionShort": "Enable material optimization function in nesting (part rotation disabled)",
       "sDescriptionLong": "",
+      "idDescriptionShortMsg": 1000011,
+      "idDescriptionLongMsg": 1000012,
       "sType": "b",
       "sMessageId": " ",
       "sMinUserLevel": "1"
@@ -70,6 +70,8 @@
       "sValue": "IF_NECESSARY",
       "sDescriptionShort": "Part rotating acceptability",
       "sDescriptionLong": "Acceptability of rotating the part between machining steps",
+      "idDescriptionShortMsg": 1000013,
+      "idDescriptionLongMsg": 1000014,
       "sType": "combo",
       "sMinUserLevel": "1",
       "Choices": [
@@ -77,18 +79,24 @@
             "sValue": "NOT_ALLOWED",
             "sDescriptionShort": "Rotation not allowed",
             "sDescriptionLong": "",
+            "idDescriptionShortMsg": 1000015,
+            "idDescriptionLongMsg": 1000016,
             "sMessageId": ""
          },
          {
             "sValue": "IF_NECESSARY",
             "sDescriptionShort": "Rotation allowed only if strictly necessary",
             "sDescriptionLong": "",
+            "idDescriptionShortMsg": 1000017,
+            "idDescriptionLongMsg": 1000018,
             "sMessageId": ""
          },
          {
             "sValue": "NO_CONSTRAINT",
             "sDescriptionShort": "Rotation easily acceptable / no constraint",
             "sDescriptionLong": "",
+            "idDescriptionShortMsg": 1000019,
+            "idDescriptionLongMsg": 1000020,
             "sMessageId": ""
          }
       ]
@@ -100,6 +108,8 @@
       "sValue": "AUTO",
       "sDescriptionShort": "Machining Strategy",
       "sDescriptionLong": "",
+      "idDescriptionShortMsg": 1000021,
+      "idDescriptionLongMsg": 1000022,
       "sType": "combo",
       "sMinUserLevel": "1",
       "Choices": [
@@ -107,18 +117,32 @@
             "sValue": "AUTO",
             "sDescriptionShort": "Quality and time equally prioritized",
             "sDescriptionLong": "",
+            "idDescriptionShortMsg": 1000023,
+            "idDescriptionLongMsg": 1000024,
             "sMessageId": ""
          },
          {
             "sValue": "FASTEST",
             "sDescriptionShort": "Fastest",
             "sDescriptionLong": "Prefer fastest strategies",
+            "idDescriptionShortMsg": 1000025,
+            "idDescriptionLongMsg": 1000026,
             "sMessageId": ""
          },
          {
             "sValue": "HIGH_QUALITY",
             "sDescriptionShort": "High quality",
             "sDescriptionLong": "Prefer high-quality strategies",
+            "idDescriptionShortMsg": 1000027,
+            "idDescriptionLongMsg": 1000028,
+            "sMessageId": ""
+         },
+         {
+            "sValue": "FIRST_IN_LIST",
+            "sDescriptionShort": "Ordering rules",
+            "sDescriptionLong": "The first complete strategy in list is the one chosen; no intelligent choosing",
+            "idDescriptionShortMsg": 1000029,
+            "idDescriptionLongMsg": 1000030,
             "sMessageId": ""
          }
       ]
@@ -130,6 +154,8 @@
       "sValue": "1",
       "sDescriptionShort": "Max number of reprocessing cycles",
       "sDescriptionLong": "",
+      "idDescriptionShortMsg": 1000031,
+      "idDescriptionLongMsg": 1000032,
       "sType": "d",
       "sMessageId": " ",
       "sMinUserLevel": "10"
@@ -141,6 +167,8 @@
       "sValue": "true",
       "sDescriptionShort": "Use entire blade diameter to shorten path",
       "sDescriptionLong": "",
+      "idDescriptionShortMsg": 1000033,
+      "idDescriptionLongMsg": 1000034,
       "sType": "b",
       "sMessageId": " ",
       "sMinUserLevel": "5"
@@ -152,6 +180,8 @@
       "sValue": "300",
       "sDescriptionShort": "Maximum length for dropped waste",
       "sDescriptionLong": "",
+      "idDescriptionShortMsg": 1000035,
+      "idDescriptionLongMsg": 1000036,
       "sType": "d",
       "sMessageId": " ",
       "sMinUserLevel": "5"
@@ -163,6 +193,8 @@
       "sValue": "6000000",
       "sDescriptionShort": "Maximum volume for dropped waste",
       "sDescriptionLong": "",
+      "idDescriptionShortMsg": 1000037,
+      "idDescriptionLongMsg": 1000038,
       "sType": "d",
       "sMessageId": " ",
       "sMinUserLevel": "5"
@@ -174,8 +206,10 @@
       "sValue": "150",
       "sDescriptionShort": "Maximum dice dimension",
       "sDescriptionLong": "",
+      "idDescriptionShortMsg": 1000039,
+      "idDescriptionLongMsg": 1000040,
       "sType": "d",
       "sMessageId": " ",
       "sMinUserLevel": "5"
    }
-]
+]

Strategies/Standard/HEADCUT/HEADCUT.json

@@ -8,6 +8,8 @@
          "sValue": "0",
          "sDescriptionShort": "Depth Chamfer",
          "sDescriptionLong": "Depth of the V-Mill to execute chamfers on cut-edges",
+         "idDescriptionShortMsg": 1000301,
+         "idDescriptionLongMsg": 1000302,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "false",
          "sDescriptionShort": "Force to use chain saw",
          "sDescriptionLong": "Force to use chain saw",
+         "idDescriptionShortMsg": 1000303,
+         "idDescriptionLongMsg": 1000304,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "false",
          "sDescriptionShort": "Force to add PreCuts",
          "sDescriptionLong": "Autocam will apply a machining on the theoretical zero, to avoid collision if the theoretical piece length doesn't correspond to the real length",
+         "idDescriptionShortMsg": 1000305,
+         "idDescriptionLongMsg": 1000306,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -38,6 +44,8 @@
          "sValue": "true",
          "sDescriptionShort": "Finish with mill",
          "sDescriptionLong": "Use a mill to finish the surface if split with chain saw",
+         "idDescriptionShortMsg": 1000307,
+         "idDescriptionLongMsg": 1000308,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -58,5 +66,4 @@
          "sMinUserLevel": "5"
       }
    ]
-}
-
+}

Strategies/Standard/HEADCUT/HEADCUT.lua

@@ -40,6 +40,11 @@ function HEADCUT.Make( bAddMachining, Proc, Part, CustomParameters)
 
    -- si setta che è taglio di testa
    Strategy.bIsHeadCut = true
+   -- quando si aggiunge la lavorazione, si cambia il nome della feature
+   if bAddMachining then
+      -- si forza il nome della feature
+      EgtSetName( Proc.id, 'StartCut')
+   end
 
    -- se abilitato, faccio tagli di PRECUT a zero (come SPLIT)
    if Strategy.Parameters.bExecutePreCut then
@@ -67,9 +72,6 @@ function HEADCUT.Make( bAddMachining, Proc, Part, CustomParameters)
 
    -- se devo applicare le lavorazioni
    if bAddMachining then
-      -- si forza il nome della feature
-      EgtSetName( Proc.id, 'StartCut')
-
       -- inserimento smussi su spigoli del taglio
       if Strategy.Parameters.bMakeChamfer then
          MakeChamfer()

Strategies/Standard/STR0001/STR0001.json

@@ -8,6 +8,8 @@
          "sValue": "0",
          "sDescriptionShort": "Overmaterial on tenon length",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000041,
+         "idDescriptionLongMsg": 1000042,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "0",
          "sDescriptionShort": "Overmaterial on tenon width",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000043,
+         "idDescriptionLongMsg": 1000044,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "3",
          "sDescriptionShort": "Maximum number of milling passes",
          "sDescriptionLong": "Maximum number of milling passes. If more passes are required, pocketing is performed",
+         "idDescriptionShortMsg": 1000045,
+         "idDescriptionLongMsg": 1000046,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -38,6 +44,8 @@
          "sValue": "true",
          "sDescriptionShort": "Use DoveTail tool to pocket",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000047,
+         "idDescriptionLongMsg": 1000048,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -48,6 +56,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Cutting Strategy",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000049,
+         "idDescriptionLongMsg": 1000050,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -55,24 +65,32 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000051,
+               "idDescriptionLongMsg": 1000052,
                "sMessageId": ""
             },
             {
                "sValue": "BLADE_FORCED",
                "sDescriptionShort": "Blade only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000053,
+               "idDescriptionLongMsg": 1000054,
                "sMessageId": ""
             },
             {
                "sValue": "MILL_FORCED",
                "sDescriptionShort": "Mill only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000055,
+               "idDescriptionLongMsg": 1000056,
                "sMessageId": ""
             },
             {
                "sValue": "CHAINSAW_FORCED",
                "sDescriptionShort": "ChainSaw only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000057,
+               "idDescriptionLongMsg": 1000058,
                "sMessageId": ""
             }
          ]
@@ -83,6 +101,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine the tenon cut surface",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000059,
+         "idDescriptionLongMsg": 1000060,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",
@@ -94,6 +114,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine the dovetail tenon",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000061,
+         "idDescriptionLongMsg": 1000062,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",

Strategies/Standard/STR0001/STR0001.lua

@@ -87,6 +87,7 @@ local function GetTenonStrategy( Proc, Part)
       ToolSearchParameters.dElevation = EgtSurfTmFacetElevationInBBox( Strategy.idTenonCutPlane, 0, Part.b3Part, true, GDB_ID.ROOT)
 
       ToolSearchParameters.vtToolDirection = Proc.FeatureInfo.vtTenonN
+      ToolSearchParameters.sMillShape = 'STANDARD'
       ToolSearchParameters.AvailableToolList = MachiningLib.GetAvailableToolList( Proc, Strategy.Parameters.sPocketingList, 'Pocketing')
       Machining.Cutting.ToolInfo = MachiningLib.FindMill( Proc, ToolSearchParameters)
 

Strategies/Standard/STR0002/STR0002.json

@@ -8,6 +8,8 @@
          "sValue": "15",
          "sDescriptionShort": "Max radius left on corners",
          "sDescriptionLong": "Radius-limit left by the tool at each corner of the feature",
+         "idDescriptionShortMsg": 1000063,
+         "idDescriptionLongMsg": 1000064,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,16 +20,32 @@
          "sValue": "false",
          "sDescriptionShort": "Use Anti-Splint strategy",
          "sDescriptionLong": "The strategy will apply blade cuts on corner to avoid wood splint",
+         "idDescriptionShortMsg": 1000065,
+         "idDescriptionLongMsg": 1000066,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
       },
+      {
+         "sName": "dExtendAfterTail",
+         "sNameNge": "EXTEND_AFTER_TAIL",
+         "sValue": "",
+         "sDescriptionShort": "Extend after tail",
+         "sDescriptionLong": "The automatism considers this length as machinable. This means you accept to damage the next piece in the bar",
+         "idDescriptionShortMsg": 1000067,
+         "idDescriptionLongMsg": 1000068,
+         "sType": "d",
+         "sMessageId": " ",
+         "sMinUserLevel": "1"
+      },
       {
          "sName": "dOpenMinSafe",
          "sNameNge": "OPENMINSAFE",
          "sValue": "10",
          "sDescriptionShort": "Minimum approach distance on open sides",
          "sDescriptionLong": "Minimum approach distance on open sides",
+         "idDescriptionShortMsg": 1000069,
+         "idDescriptionLongMsg": 1000070,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -38,6 +56,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to pocket the feature",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000071,
+         "idDescriptionLongMsg": 1000072,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",

Strategies/Standard/STR0002/STR0002.lua

@@ -19,6 +19,7 @@ local BeamLib = require( 'BeamLib')
 local BeamData = require( 'BeamDataNew')
 local MachiningLib = require( 'MachiningLib')
 local FeatureLib = require( 'FeatureLib')
+local AntiSplintOnFace = require( 'ANTISPLINTONFACE')
 
 -- Tabella per definizione modulo
 local STR0002 = {}
@@ -26,7 +27,8 @@ local Strategy = {}
 
 -------------------------------------------------------------------------------------------------------------
 local function IsTopologyOk( Proc)
-   if Proc.Topology.sName == 'Pocket-5-Blind' or
+   if Proc.Topology.sFamily == 'PseudoPocket' or
+      Proc.Topology.sName == 'Pocket-5-Blind' or
       Proc.Topology.sName == 'RafterNotch-5-Through' or
       Proc.Topology.sName == 'Tunnel-4-Through' or
       Proc.Topology.sName == 'Groove-4-Blind' or
@@ -107,7 +109,7 @@ local function GetBestPocketingStrategy( Proc, Part)
    local Milling = {}
    local ToolSearchParameters = {}
    ToolSearchParameters.sMillShape = 'STANDARD'
-   Machining.sTypeMachining = 'None' -- Bottom-Side1-Side2\ Bottom-Side1\ Bottom-Side2\ Side1-Side2\ Bottom\ Side1 \ Side2 \ None
+   Machining.sTypeMachining = 'None' -- Bottom-Side1-Side2\ Bottom-Bottom2\ Bottom-Side1\ Bottom-Side2\ Side1-Side2\ Bottom\ Side1 \ Side2 \ None
    Strategy.Result.dQuality = FeatureLib.GetStrategyQuality( 'STD')
 
    -- caso speciale Tunnel che non ha faccia bottom
@@ -120,7 +122,7 @@ local function GetBestPocketingStrategy( Proc, Part)
       ToolSearchParameters.sType = 'MILL_STD'
       ToolSearchParameters.dMaxToolDiameter = min( Strategy.Parameters.dMaxCornerRadius * 2, Proc.FeatureInfo.dFaceLength / 2)
    -- imposto dati per cercare la fresa migliore
-   elseif Proc.Topology.sName == 'Pocket-5-Blind' then
+   elseif Proc.Topology.sName == 'Pocket-5-Blind' or Proc.Topology.sFamily == 'PseudoPocket' then
       local dFaceWidth, dFaceLength
       if Proc.MainFaces.BottomFaces[1].MainEdges then
          dFaceWidth = Proc.MainFaces.BottomFaces[1].MainEdges.LongEdges[1].dLength
@@ -170,10 +172,14 @@ local function GetBestPocketingStrategy( Proc, Part)
    -- cerco utensile per lavorare faccia Bottom
    Milling.bIsApplicable = false
    if Proc.Topology.sName ~= 'Tunnel-4-Through' then
+      -- TODO in caso che la faccia crei un piano asportando tutto il materiale, si potrebbe forzare elevazione a zero e scegliere quindi fresa di diametro maggiore.
+      -- Il discorso non vale se la feature viene spezzata o se non ancora separata, in quanto ci sarebbe comunque del materiale da considerare nell'elevazione.
+      -- In quel caso, un 'Bevel-1-Through' è come se fosse un 'Bevel-2-Blind', quindi l'elevazione deve essere considerata.
       ToolSearchParameters.dElevation = Proc.MainFaces.BottomFaces[1].dElevation
       ToolSearchParameters.vtToolDirection = Proc.MainFaces.BottomFaces[1].vtN
       ToolSearchParameters.AvailableToolList = MachiningLib.GetAvailableToolList( Proc, Strategy.Parameters.sPocketingList, 'Pocketing')
       Milling.idFaceToMachine = Proc.MainFaces.BottomFaces[1].id
+      Milling.bAddAntiSplint = Strategy.Parameters.bAntiSplint
       Milling.idProc = Proc.id
       Milling.vtFaceNormal = Proc.MainFaces.BottomFaces[1].vtN
       Milling.dElevation = Proc.MainFaces.BottomFaces[1].dElevation
@@ -204,13 +210,14 @@ local function GetBestPocketingStrategy( Proc, Part)
    -- caso speciale 'Rabbet-2-Through' seconda faccia principale
    Milling = {}
    Milling.bIsApplicable = false
-   if Proc.Topology.sName == 'Rabbet-2-Through' or Proc.Topology.sName == 'Bevel-2-Blind' or 
+   if Proc.Topology.sName == 'Rabbet-2-Through' or Proc.Topology.sName == 'Bevel-2-Blind' or
       Proc.Topology.sName == 'DoubleBevel-2-Through' or Proc.Topology.sName == 'VGroove-2-Through' then
       ToolSearchParameters.dElevation = Proc.MainFaces.BottomFaces[2].dElevation
       ToolSearchParameters.vtToolDirection = Proc.MainFaces.BottomFaces[2].vtN
       ToolSearchParameters.AvailableToolList = MachiningLib.GetAvailableToolList( Proc, Strategy.Parameters.sPocketingList, 'Pocketing')
       Milling.vtFaceNormal = Proc.MainFaces.BottomFaces[2].vtN
       Milling.idFaceToMachine = Proc.MainFaces.BottomFaces[2].id
+      Milling.bAddAntiSplint = Strategy.Parameters.bAntiSplint
       Milling.idProc = Proc.id
       Milling.dElevation = Proc.MainFaces.BottomFaces[2].dElevation
       Milling.ToolInfo = {}
@@ -227,7 +234,7 @@ local function GetBestPocketingStrategy( Proc, Part)
    -- cerco utensile per lavorare di fianco 1
    Milling = {}
    Milling.bIsApplicable = false
-   if Proc.Topology.sName ~= 'DoubleBevel-2-Through'
+   if Proc.Topology.sName ~= 'DoubleBevel-2-Through' and Proc.Topology.sFamily ~= 'PseudoPocket'
       and Proc.Topology.sName ~= 'Pocket-5-Blind' and Proc.Topology.sName ~=  'RafterNotch-5-Through' then
 
       if Proc.Topology.sName ==  'Groove-4-Blind' then
@@ -238,12 +245,21 @@ local function GetBestPocketingStrategy( Proc, Part)
          Milling.idProc = Proc.id
          Milling.dElevation = Proc.MainFaces.BottomFaces[2].dElevation
       elseif Proc.Topology.sName ==  'Groove-3-Blind' or Proc.Topology.sName ==  'Bevel-3-Blind' then
-         ToolSearchParameters.dElevation = Proc.MainFaces.LongFaces[1].dElevation
-         ToolSearchParameters.vtToolDirection = Proc.MainFaces.LongFaces[1].vtN
-         Milling.vtFaceNormal = Proc.MainFaces.LongFaces[1].vtN
-         Milling.idFaceToMachine = Proc.MainFaces.LongFaces[1].id
-         Milling.idProc = Proc.id
-         Milling.dElevation = Proc.MainFaces.LongFaces[1].dElevation
+         if Proc.MainFaces.LongFaces and Proc.MainFaces.LongFaces[1] then
+            ToolSearchParameters.dElevation = Proc.MainFaces.LongFaces[1].dElevation
+            ToolSearchParameters.vtToolDirection = Proc.MainFaces.LongFaces[1].vtN
+            Milling.vtFaceNormal = Proc.MainFaces.LongFaces[1].vtN
+            Milling.idFaceToMachine = Proc.MainFaces.LongFaces[1].id
+            Milling.idProc = Proc.id
+            Milling.dElevation = Proc.MainFaces.LongFaces[1].dElevation
+         elseif Proc.MainFaces.BottomFaces[2] then
+            ToolSearchParameters.dElevation = Proc.MainFaces.BottomFaces[2].dElevation
+            ToolSearchParameters.vtToolDirection = Proc.MainFaces.BottomFaces[2].vtN
+            Milling.vtFaceNormal = Proc.MainFaces.BottomFaces[2].vtN
+            Milling.idFaceToMachine = Proc.MainFaces.BottomFaces[2].id
+            Milling.idProc = Proc.id
+            Milling.dElevation = Proc.MainFaces.BottomFaces[2].dElevation
+         end
       elseif Proc.MainFaces.TunnelAddedFaces then -- 'Tunnel-4-Through', 'Groove-3-Through', 'Rabbet-2-Through', 'VGroove-2-Through', 'Bevel-2-Blind'
          -- se lavoro di fianco, devo comunque rispettare il raggio massimo
          ToolSearchParameters.dMaxToolDiameter = min( ToolSearchParameters.dMaxToolDiameter, Strategy.Parameters.dMaxCornerRadius * 2)
@@ -254,6 +270,8 @@ local function GetBestPocketingStrategy( Proc, Part)
          Milling.idProc = Proc.MainFaces.TunnelAddedFaces.MiddleFaceTm.id
          Milling.dElevation = ( Proc.MainFaces.TunnelAddedFaces.MiddleFaceTm.Faces[1].dElevation * 2) + BeamData.MILL_OVERLAP
          Milling.bMachAppliedToTunnelFace = true
+      else
+         ToolSearchParameters.vtToolDirection = nil
       end
       ToolSearchParameters.AvailableToolList = MachiningLib.GetAvailableToolList( Proc, Strategy.Parameters.sPocketingList, 'Pocketing')
       Milling.ToolInfo = {}
@@ -263,6 +281,19 @@ local function GetBestPocketingStrategy( Proc, Part)
          local ParametersMRR = {}
          ParametersMRR.nToolIndex = Milling.ToolInfo.nToolIndex
          Milling.dMRR = MachiningLib.GetToolMRR( ParametersMRR)
+         -- se la faccia tunnel è troppo piccola non si lavora
+         if Milling.bMachAppliedToTunnelFace then
+            local dLongestEdgeLength = 0
+            for i = 1, #Proc.MainFaces.TunnelAddedFaces.MiddleFaceTm.Faces[1].Edges do
+               if Proc.MainFaces.TunnelAddedFaces.MiddleFaceTm.Faces[1].Edges[i].dLength > dLongestEdgeLength + 10 * GEO.EPS_SMALL then
+                  dLongestEdgeLength = Proc.MainFaces.TunnelAddedFaces.MiddleFaceTm.Faces[1].Edges[i].dLength
+               end
+            end
+            if dLongestEdgeLength < TOOLS[Milling.ToolInfo.nToolIndex].dDiameter then
+               Milling.bIsApplicable = false
+               ParametersMRR = {}
+            end
+         end
       end
    end
    table.insert( Machining, Milling)
@@ -272,6 +303,7 @@ local function GetBestPocketingStrategy( Proc, Part)
    Milling.bIsApplicable = false
    if Proc.Topology.sName ~= 'DoubleBevel-2-Through'
       and Proc.Topology.sName ~= 'Pocket-5-Blind'
+      and Proc.Topology.sFamily ~= 'PseudoPocket'
       and Proc.Topology.sName ~=  'RafterNotch-5-Through'
       and Proc.Topology.sName ~= 'Groove-4-Blind'
       and Proc.Topology.sName ~=  'Bevel-3-Blind' then
@@ -294,6 +326,8 @@ local function GetBestPocketingStrategy( Proc, Part)
          Milling.idFaceToMachine = Proc.MainFaces.SideFaces[1].id
          Milling.idProc = Proc.id
          Milling.dElevation = Proc.MainFaces.SideFaces[1].dElevation
+      else
+         ToolSearchParameters.vtToolDirection = nil
       end
       ToolSearchParameters.AvailableToolList = MachiningLib.GetAvailableToolList( Proc, Strategy.Parameters.sPocketingList, 'Pocketing')
       Milling.ToolInfo = {}
@@ -303,13 +337,60 @@ local function GetBestPocketingStrategy( Proc, Part)
          local ParametersMRR = {}
          ParametersMRR.nToolIndex = Milling.ToolInfo.nToolIndex
          Milling.dMRR = MachiningLib.GetToolMRR( ParametersMRR)
+         -- se la faccia tunnel è troppo piccola non si lavora
+         if Milling.bMachAppliedToTunnelFace then
+            local dLongestEdgeLength = 0
+            for i = 1, #Proc.MainFaces.TunnelAddedFaces.MiddleFaceTm.Faces[1].Edges do
+               if Proc.MainFaces.TunnelAddedFaces.MiddleFaceTm.Faces[1].Edges[i].dLength > dLongestEdgeLength + 10 * GEO.EPS_SMALL then
+                  dLongestEdgeLength = Proc.MainFaces.TunnelAddedFaces.MiddleFaceTm.Faces[1].Edges[i].dLength
+               end
+            end
+            if dLongestEdgeLength < TOOLS[Milling.ToolInfo.nToolIndex].dDiameter then
+               Milling.bIsApplicable = false
+               ParametersMRR = {}
+            end
+         end
       end
    end
    table.insert( Machining, Milling)
 
    --  ===== SCELTA LAVORAZIONI =====
+   -- TODO per DoubleBevel-2-Through si potrebbe lavorare la faccia tunnel su ogni faccia. Bisogna calcolarla!!
+   -- caso speciale DoubleBevel-2-Through bisogna lavorare entrambe le bottom
+   if Proc.Topology.sName == 'DoubleBevel-2-Through' then
+      -- se entrambe applicabili significa che è completo
+      if Machining[1].bIsApplicable and Machining[2].bIsApplicable then
+         Machining.sTypeMachining = 'Bottom-Bottom2'
+         Strategy.Result.sStatus = 'Completed'
+         Strategy.Result.dCompletionIndex = FeatureLib.GetFeatureCompletionIndex( 100)
+         Strategy.Result.dMRR = Machining[1].dMRR + Machining[2].dMRR / 2
+         Machining[1].ToolInfo.dResidualDepth = 0
+         Machining[2].ToolInfo.dResidualDepth = 0
+         return Machining
+      else
+         local dMachinedPrercentage = 0
+         -- se applicabile solo Bottom
+         if Machining[1].bIsApplicable then
+            Machining.sTypeMachining = 'Bottom'
+            Strategy.Result.sStatus = 'Not-Completed'
+            Machining[1].ToolInfo.dResidualDepth = 0
+            Strategy.Result.dMRR = Machining[1].dMRR
+            dMachinedPrercentage = ( Machining[1].dElevation / ( Machining[1].dElevation + Machining[2].dElevation)) * 100
+            Strategy.Result.dCompletionIndex = FeatureLib.GetFeatureCompletionIndex( dMachinedPrercentage)
+         -- se applicabile solo Bottom2
+         elseif Machining[2].bIsApplicable then
+            Machining.sTypeMachining = 'Bottom2'
+            Strategy.Result.sStatus = 'Not-Completed'
+            Machining[2].ToolInfo.dResidualDepth = 0
+            Strategy.Result.dMRR = Machining[2].dMRR
+            dMachinedPrercentage = ( Machining[2].dElevation / ( Machining[1].dElevation + Machining[2].dElevation)) * 100
+            Strategy.Result.dCompletionIndex = FeatureLib.GetFeatureCompletionIndex( dMachinedPrercentage)
+         end
+         Strategy.Result.sInfo = 'Machining not complete, left ' .. tostring( 100 - ceil( dMachinedPrercentage)) .. '%'
+      end
+      return Machining
    -- se bottom completa tutto
-   if Machining[1].bIsApplicable and Machining[1].ToolInfo.dResidualDepth < 10 * GEO.EPS_SMALL then
+   elseif Machining[1].bIsApplicable and Machining[1].ToolInfo.dResidualDepth < 10 * GEO.EPS_SMALL then
       Machining.sTypeMachining = 'Bottom'
       Strategy.Result.sStatus = 'Completed'
       Strategy.Result.dCompletionIndex = FeatureLib.GetFeatureCompletionIndex( 100)
@@ -321,10 +402,10 @@ local function GetBestPocketingStrategy( Proc, Part)
       if ( Proc.nFct == 2 and Proc.AdjacencyMatrix[1][2] >= -89.9)
          and Machining[2].bIsApplicable and Machining[2].ToolInfo.dResidualDepth < 10 * GEO.EPS_SMALL then
          
-         Machining.sTypeMachining = 'Bottom2'
+         Machining.sTypeMachining = 'Bottom-Bottom2'
          Strategy.Result.sStatus = 'Completed'
          Strategy.Result.dCompletionIndex = FeatureLib.GetFeatureCompletionIndex( 100)
-         Strategy.Result.dMRR = Machining[2].dMRR
+         Strategy.Result.dMRR = Machining[1].dMRR + Machining[2].dMRR / 2
          Machining[2].ToolInfo.dResidualDepth = 0
       else
          Machining[2].bIsApplicable = false
@@ -549,8 +630,8 @@ function STR0002.Make( bAddMachining, Proc, Part, CustomParameters)
                Pocketing.Steps.dStep = TOOLS[Strategy.Machining[j].ToolInfo.nToolIndex].dStep
                Pocketing.Steps.dSideStep = TOOLS[Strategy.Machining[j].ToolInfo.nToolIndex].dSideStep
                Pocketing.nToolIndex = Strategy.Machining[j].ToolInfo.nToolIndex
-               Pocketing.LeadIn.dTangentDistance = TOOLS[Strategy.Machining[j].ToolInfo.nToolIndex].dDiameter/2
-               Pocketing.LeadIn.dElevation = TOOLS[Strategy.Machining[j].ToolInfo.nToolIndex].dDiameter/2
+               Pocketing.LeadIn.dTangentDistance = TOOLS[Strategy.Machining[j].ToolInfo.nToolIndex].dDiameter / 2
+               Pocketing.LeadIn.dElevation = TOOLS[Strategy.Machining[j].ToolInfo.nToolIndex].dDiameter / 2
                Pocketing.sDepth = -Strategy.Machining[j].ToolInfo.dResidualDepth
                Pocketing.dResidualDepth = Strategy.Machining[j].ToolInfo.dResidualDepth
                -- TODO vedere se questo parametro con svuotature nuove si può rimuovere
@@ -559,11 +640,35 @@ function STR0002.Make( bAddMachining, Proc, Part, CustomParameters)
                if Strategy.Machining[j].bToolInvert then
                   Pocketing.bToolInvert = true
                end
+               -- eventuali antischeggia
+               if Strategy.Machining[j].bAddAntiSplint then
+                  local OptionalParametersAntiSplint = {
+                     bIsSplitFeature = ( #vAddId > 1),
+                     dExtendAfterTail = Strategy.Parameters.dExtendAfterTail
+                  }
+                  local AntiSplints = AntiSplintOnFace.Make( Proc, Part, Proc.Faces[ Strategy.Machining[j].idFaceToMachine + 1], OptionalParametersAntiSplint)
+                  local bAreAllAntisplintsApplicable = true
+                  for k = 1, #AntiSplints do
+                     if AntiSplints[k].bIsApplicable then
+                        if bAddMachining then
+                           bAreAllMachiningsAdded = MachiningLib.AddMachinings( Proc, AntiSplints[k])
+                        end
+                     else
+                        bAreAllAntisplintsApplicable = false
+                     end
+                  end
+                  if bAreAllAntisplintsApplicable then
+                     -- TODO qui si dovrà distinguere tra antischeggia di lama e di fresa; al momento è solo di lama
+                     if Strategy.Result.dQuality == FeatureLib.GetStrategyQuality( 'STD') then
+                        Strategy.Result.dQuality = FeatureLib.GetStrategyQuality( 'BEST')
+                     end
+                  end
+               end
                -- se ho una sola trimesh, sto lavorando la Proc direttamente e non ho spezzato. Applico direttamente alla geometria calcolata prima
                if #vAddId == 1 then
                   Pocketing.Geometry = {{ Strategy.Machining[j].idProc, Strategy.Machining[j].idFaceToMachine}}
                   Pocketing.vtToolDirection = Strategy.Machining[j].vtFaceNormal
-                  
+
                   -- TODO controllare parametro danneggiamento ammesso per decidere se spostare dopo taglio seprazione
                   -- se è aperta sulla coda, dico che deve essere fatta dopo la separazione
                   if Proc.AffectedFaces.bLeft then
@@ -593,10 +698,10 @@ function STR0002.Make( bAddMachining, Proc, Part, CustomParameters)
                      end
                      if vtNSplitFace and AreSameVectorApprox( vtNSplitFace * EgtIf( Pocketing.bToolInvert, -1, 1), Strategy.Machining[j].vtFaceNormal) then
                         Pocketing.Geometry = {{ nIdTm, k - 1}}
-                        
+
                         Pocketing.dTimeToMachine = MachiningLib.GetTimeToMachineAllStepsWithLeadInOut( Pocketing, Part)
                         Strategy.Result.dTimeToMachine = Strategy.Result.dTimeToMachine + Pocketing.dTimeToMachine
-                        
+
                         if bAddMachining then
                            bAreAllMachiningsAdded = bAreAllMachiningsAdded and MachiningLib.AddMachinings( Proc, Pocketing)
                         end

Strategies/Standard/STR0003/STR0003.json

@@ -8,6 +8,8 @@
          "sValue": "true",
          "sDescriptionShort": "Finish with chainsaw if needed",
          "sDescriptionLong": "Finish with chainsaw if needed",
+         "idDescriptionShortMsg": 1000073,
+         "idDescriptionLongMsg": 1000074,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -17,7 +19,9 @@
          "sNameNge": "EXTEND_AFTER_TAIL",
          "sValue": "",
          "sDescriptionShort": "Extend after tail",
-         "sDescriptionLong": "The automatism considers this lenght as machinable. This means you accept to damage the next piece in the bar",
+         "sDescriptionLong": "The automatism considers this length as machinable. This means you accept to damage the next piece in the bar",
+         "idDescriptionShortMsg": 1000075,
+         "idDescriptionLongMsg": 1000076,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "false",
          "sDescriptionShort": "Force ripping blade",
          "sDescriptionLong": "Force the use of ripping blade, designed for cuts parallel to the grain",
+         "idDescriptionShortMsg": 1000077,
+         "idDescriptionLongMsg": 1000078,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -38,6 +44,8 @@
          "sValue": "true",
          "sDescriptionShort": "Not complete with Blade radius imprint left",
          "sDescriptionLong": "If the parameter is active, the automatism considers the feature as - not complete - if the blade radius imprint is left",
+         "idDescriptionShortMsg": 1000079,
+         "idDescriptionLongMsg": 1000080,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -48,6 +56,8 @@
          "sValue": "false",
          "sDescriptionShort": "Use Zig-Zag ChainSaw",
          "sDescriptionLong": "Enable the parameter to set the Zig-Zag movement on the ChainSaw machining. Deactivate it to use One-Way movement.",
+         "idDescriptionShortMsg": 1000081,
+         "idDescriptionLongMsg": 1000082,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -58,6 +68,8 @@
          "sValue": "true",
          "sDescriptionShort": "Sort by segment",
          "sDescriptionLong": "Sort the machinings according to the piece-segment where the machining has inserted",
+         "idDescriptionShortMsg": 1000083,
+         "idDescriptionLongMsg": 1000084,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -68,6 +80,8 @@
          "sValue": "NEVER",
          "sDescriptionShort": "Damage next piece",
          "sDescriptionLong": "This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time",
+         "idDescriptionShortMsg": 1000085,
+         "idDescriptionLongMsg": 1000086,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -75,18 +89,24 @@
                "sValue": "NEVER",
                "sDescriptionShort": "Never damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000087,
+               "idDescriptionLongMsg": 1000088,
                "sMessageId": ""
             },
             {
                "sValue": "ONLY_IF_RAWPART",
                "sDescriptionShort": "Damage only if raw",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000089,
+               "idDescriptionLongMsg": 1000090,
                "sMessageId": ""
             },
             {
                "sValue": "ALWAYS",
                "sDescriptionShort": "Can damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000091,
+               "idDescriptionLongMsg": 1000092,
                "sMessageId": ""
             }
          ]

Strategies/Standard/STR0003/STR0003.lua

@@ -35,12 +35,19 @@ Chainsaw.Result = {}
 local function IsTopologyOk( Proc)
    if Proc.Topology.bAllRightAngles and
       ( Proc.Topology.sName == 'Pocket-5-Blind' or
-        Proc.Topology.sName == 'Groove-3-Through' or
         Proc.Topology.sName == 'Groove-4-Blind'  or
         Proc.Topology.sName == 'Tunnel-4-Through') then
 
       return true
+
+   -- canale ammesso solo se lati paralleli a 2 a 2
+   elseif Proc.Topology.sName == 'Groove-3-Through'
+      and ( AreOppositeVectorApprox( Proc.MainFaces.BottomFaces[1].MainEdges.LongEdges[1].vtN, Proc.MainFaces.BottomFaces[1].MainEdges.LongEdges[2].vtN)) then
+
+      return true
+
    else
+
       return false
    end
 end
@@ -188,6 +195,17 @@ function STR0003.Make( bAddMachining, Proc, Part, CustomParameters)
    Blade.Result = {}
    Chainsaw.Result = {}
 
+
+   -- se arriva una feature senza MainFaces o MainEdges necessari la strategia non è applicabile
+   -- TODO riuniure a IsTopologyOk?
+   if not Proc.MainFaces
+      or not Proc.MainFaces.LongFaces[1]
+      or not Proc.MainFaces.LongFaces[1].MainEdges then
+
+      Strategy.Result = FeatureLib.GetStrategyResultNotApplicable( 'Topology')
+      return false, Strategy.Result
+   end
+
    if not IsTopologyOk( Proc) then
       local sErr = 'Feature '.. Proc.idFeature .. ' : strategy ' .. Strategy.sName .. ' not implemented'
       EgtOutLog( sErr)
@@ -195,13 +213,15 @@ function STR0003.Make( bAddMachining, Proc, Part, CustomParameters)
       return false, Strategy.Result
    end
 
-   -- se tasca su faccia sotto la strategia non è applicabile (la sega a catena in generale non può lavorare da sotto)
-   -- TODO se OnlySaw questo test è da rimuovere ma bisogna considerare anche la lama da sotto
-   if Proc.AffectedFaces.bBottom and ( Proc.nFct > 3 or not Proc.AffectedFaces.bTop) then
-      local sErr = 'Feature '.. Proc.idFeature .. ' : strategy ' .. Strategy.sName .. ' not applicable - pocket on bottom face'
-      EgtOutLog( sErr)
-      Strategy.Result = FeatureLib.GetStrategyResultNotApplicable( 'Direction')
-      return false, Strategy.Result
+   -- se canale e lati non a 90deg la strategia non è applicabile
+   -- TODO questo è temporaneo finchè non si gestiscono correttamente i lati obliqui per le groove-3-through
+   -- la dPocketHeight è già gestita, ma va allungato il percorso dove c'è l'angolo > 90
+   if Proc.Topology.sName == 'Groove-3-Through' then
+      local BottomFace = Proc.MainFaces.BottomFaces[1]
+      if abs( BottomFace.Edges[1].vtEdge * BottomFace.Edges[2].vtEdge) > 10 * GEO.EPS_SMALL then
+         Strategy.Result = FeatureLib.GetStrategyResultNotApplicable( 'Topology')
+         return false, Strategy.Result
+      end
    end
 
    local dExtendAfterTail = Strategy.Parameters.dExtendAfterTail or max( Part.dDistanceToNextPiece - BeamData.CUT_EXTRA, 0)
@@ -223,6 +243,11 @@ function STR0003.Make( bAddMachining, Proc, Part, CustomParameters)
    local dPocketHeight = 0
    if Proc.Topology.sFamily == 'Tunnel' then
       dPocketHeight = Proc.MainFaces.SideFaces[1].MainEdges.OppositeEdges[1].dLength
+   elseif Proc.Topology.sName == 'Groove-3-Through' then
+      local BottomFace = Proc.MainFaces.BottomFaces[1]
+      local frFrame = Frame3d( BottomFace.ptCenter, BottomFace.vtN, BottomFace.MainEdges.LongEdges[1].vtEdge)
+      local b3BottomFace = EgtSurfTmGetFacetBBoxRef( Proc.id, BottomFace.id, GDB_BB.STANDARD, frFrame)
+      dPocketHeight = b3BottomFace:getDimY()
    else
       dPocketHeight = Proc.MainFaces.BottomFaces[1].MainEdges.SideEdges[1].dLength
    end
@@ -390,7 +415,8 @@ function STR0003.Make( bAddMachining, Proc, Part, CustomParameters)
       end
       
       -- ancora materiale residuo - se possibile si lavora dal lato
-      if Chainsaw.Result.Bottom[#Chainsaw.Result.Bottom].dResidualDepth > 10 * GEO.EPS_SMALL
+      if ( Chainsaw.Result.Bottom[#Chainsaw.Result.Bottom].dResidualDepth > 10 * GEO.EPS_SMALL
+         or not Chainsaw.Result.Bottom[#Chainsaw.Result.Bottom].bIsApplicable)
          and #Proc.MainFaces.SideFaces == 1 then
 
          -- si lavora solamente l'impronta lama sul fondo
@@ -673,7 +699,13 @@ function STR0003.Make( bAddMachining, Proc, Part, CustomParameters)
       else
          Strategy.Result.sStatus = 'Not-Completed'
       end
-      Strategy.Result.dQuality = FeatureLib.GetStrategyQuality( Result)
+
+      if Proc.Topology.sName == 'Groove-4-Blind' or Proc.Topology.sName == 'Pocket-5-Blind' then
+         Strategy.Result.dQuality = FeatureLib.GetStrategyQuality( 'SEMI')
+      else
+         Strategy.Result.dQuality = FeatureLib.GetStrategyQuality( Result)
+      end
+
       Strategy.Result.dTimeToMachine = FeatureLib.GetStrategyTimeToMachine( Result)
       Strategy.Result.dMRR = ( dFeatureVolume / Strategy.Result.dTimeToMachine) / pow( 10, 6)
    else

Strategies/Standard/STR0004/STR0004.json

@@ -8,6 +8,8 @@
          "sValue": "false",
          "sDescriptionShort": "Use Zig-Zag ChainSaw",
          "sDescriptionLong": "Enable the parameter to set the Zig-Zag movement on the ChainSaw machining. Deactivate it to use One-Way movement.",
+         "idDescriptionShortMsg": 1000093,
+         "idDescriptionLongMsg": 1000094,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -17,7 +19,9 @@
          "sNameNge": "EXTEND_AFTER_TAIL",
          "sValue": "",
          "sDescriptionShort": "Extend after tail",
-         "sDescriptionLong": "The automatism considers this lenght as machinable. This means you accept to damage the next piece in the bar",
+         "sDescriptionLong": "The automatism considers this length as machinable. This means you accept to damage the next piece in the bar",
+         "idDescriptionShortMsg": 1000095,
+         "idDescriptionLongMsg": 1000096,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "NEVER",
          "sDescriptionShort": "Damage next piece",
          "sDescriptionLong": "This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time",
+         "idDescriptionShortMsg": 1000097,
+         "idDescriptionLongMsg": 1000098,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -35,18 +41,24 @@
                "sValue": "NEVER",
                "sDescriptionShort": "Never damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000099,
+               "idDescriptionLongMsg": 1000100,
                "sMessageId": ""
             },
             {
                "sValue": "ONLY_IF_RAWPART",
                "sDescriptionShort": "Damage only if raw",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000101,
+               "idDescriptionLongMsg": 1000102,
                "sMessageId": ""
             },
             {
                "sValue": "ALWAYS",
                "sDescriptionShort": "Can damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000103,
+               "idDescriptionLongMsg": 1000104,
                "sMessageId": ""
             }
          ]

Strategies/Standard/STR0004/STR0004.lua

@@ -112,8 +112,6 @@ function STR0004.Make( bAddMachining, Proc, Part, CustomParameters)
    Chainsaw.Result = {}
 
    if not IsTopologyOk( Proc) then
-      local sErr = 'Feature '.. Proc.idFeature .. ' : strategy ' .. Strategy.sName .. ' not implemented'
-      EgtOutLog( sErr)
       Strategy.Result = FeatureLib.GetStrategyResultNotApplicable( 'Topology')
       return false, Strategy.Result
    end
@@ -134,10 +132,25 @@ function STR0004.Make( bAddMachining, Proc, Part, CustomParameters)
       bIsSplitFeature = true
    end
 
+   -- se arriva una feature senza MainFaces o MainEdges necessari la strategia non è applicabile
+   -- TODO riuniure a IsTopologyOk?
+   if not Proc.MainFaces
+      or not Proc.MainFaces.LongFaces[1]
+      or not Proc.MainFaces.LongFaces[1].MainEdges then
+
+      Strategy.Result = FeatureLib.GetStrategyResultNotApplicable( 'Topology')
+      return false, Strategy.Result
+   end
+
    -- altezza tasca
    local dPocketHeight = 0
    if Proc.Topology.sFamily == 'Tunnel' then
       dPocketHeight = Proc.MainFaces.SideFaces[1].MainEdges.OppositeEdges[1].dLength
+   elseif Proc.Topology.sName == 'Groove-3-Through' then
+      local BottomFace = Proc.MainFaces.BottomFaces[1]
+      local frFrame = Frame3d( BottomFace.ptCenter, BottomFace.vtN, BottomFace.MainEdges.LongEdges[1].vtEdge)
+      local b3BottomFace = EgtSurfTmGetFacetBBoxRef( Proc.id, BottomFace.id, GDB_BB.STANDARD, frFrame)
+      dPocketHeight = b3BottomFace:getDimY()
    else
       dPocketHeight = Proc.MainFaces.BottomFaces[1].MainEdges.SideEdges[1].dLength
    end
@@ -172,13 +185,17 @@ function STR0004.Make( bAddMachining, Proc, Part, CustomParameters)
          and #Proc.MainFaces.SideFaces == 1 then
 
          OptionalParameters.OppositeToolDirectionMode = 'Enabled'
+         local dLengthAlreadyMachined = 0
+         if Chainsaw.Result.Bottom[1].bIsApplicable then
+            dLengthAlreadyMachined = Chainsaw.Result.Bottom[1].dDepthToMachine
+         end
             
          if BottomEdge.bIsStartOpen then
             Mortising = FaceByChainsaw.Make( Proc, Part, LongFace, SideEdge1, OptionalParameters)
-            Mortising.dAreaToMachine = Mortising.dDepthToMachine * ( Mortising.dEdgeLength - Chainsaw.Result.Bottom[1].dDepthToMachine)
+            Mortising.dAreaToMachine = Mortising.dDepthToMachine * ( Mortising.dEdgeLength - dLengthAlreadyMachined)
          elseif BottomEdge.bIsEndOpen then
             Mortising = FaceByChainsaw.Make( Proc, Part, LongFace, SideEdge2, OptionalParameters)
-            Mortising.dAreaToMachine = Mortising.dDepthToMachine * ( Mortising.dEdgeLength - Chainsaw.Result.Bottom[1].dDepthToMachine)
+            Mortising.dAreaToMachine = Mortising.dDepthToMachine * ( Mortising.dEdgeLength - dLengthAlreadyMachined)
          end
 
          Chainsaw.AddResult( Mortising)
@@ -235,10 +252,21 @@ function STR0004.Make( bAddMachining, Proc, Part, CustomParameters)
       Mortising = FaceByChainsaw.Make( Proc, Part, LongFace, OppositeEdge1, OptionalParameters)
       Chainsaw.AddResult( Mortising)
 
+      -- se dal lato OppositeEdge1 non è applicabile (solitamente per finecorsa) si prova dal lato opposto
+      if not Chainsaw.Result.Opposite[1].bIsApplicable then
+         OptionalParameters.dDepthToMachine = OppositeEdge2.dElevation + BeamData.CUT_EXTRA
+         Mortising = FaceByChainsaw.Make( Proc, Part, LongFace, OppositeEdge2, OptionalParameters)
+         Chainsaw.AddResult( Mortising)
+      end
+
       -- se lavorando solo da un lato rimane materiale residuo, si lavora da entrambi
-      if Chainsaw.Result.Opposite[1].dResidualDepth > 10 * GEO.EPS_SMALL then
+      if Chainsaw.Result.Opposite[1].dResidualDepth > 10 * GEO.EPS_SMALL
+         or ( Chainsaw.Result.Opposite[2] and Chainsaw.Result.Opposite[2].dResidualDepth > 10 * GEO.EPS_SMALL) then
 
          Chainsaw.Result.Opposite[1].bIsApplicable = false
+         if Chainsaw.Result.Opposite[2] then
+            Chainsaw.Result.Opposite[2].bIsApplicable = false
+         end
          
          OptionalParameters.dDepthToMachine = OppositeEdge1.dElevation / 2 + BeamData.CUT_EXTRA_MIN
 

Strategies/Standard/STR0005/STR0005.json

@@ -8,6 +8,8 @@
          "sValue": "false",
          "sDescriptionShort": "Force ripping blade",
          "sDescriptionLong": "Force the use of ripping blade, designed for cuts parallel to the grain",
+         "idDescriptionShortMsg": 1000105,
+         "idDescriptionLongMsg": 1000106,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -17,7 +19,9 @@
          "sNameNge": "EXTEND_AFTER_TAIL",
          "sValue": "",
          "sDescriptionShort": "Extend after tail",
-         "sDescriptionLong": "The automatism considers this lenght as machinable. This means you accept to damage the next piece in the bar",
+         "sDescriptionLong": "The automatism considers this length as machinable. This means you accept to damage the next piece in the bar",
+         "idDescriptionShortMsg": 1000107,
+         "idDescriptionLongMsg": 1000108,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "NEVER",
          "sDescriptionShort": "Damage next piece",
          "sDescriptionLong": "This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time",
+         "idDescriptionShortMsg": 1000109,
+         "idDescriptionLongMsg": 1000110,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -35,18 +41,24 @@
                "sValue": "NEVER",
                "sDescriptionShort": "Never damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000111,
+               "idDescriptionLongMsg": 1000112,
                "sMessageId": ""
             },
             {
                "sValue": "ONLY_IF_RAWPART",
                "sDescriptionShort": "Damage only if raw",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000113,
+               "idDescriptionLongMsg": 1000114,
                "sMessageId": ""
             },
             {
                "sValue": "ALWAYS",
                "sDescriptionShort": "Can damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000115,
+               "idDescriptionLongMsg": 1000116,
                "sMessageId": ""
             }
          ]
@@ -57,6 +69,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Cutting strategy",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000117,
+         "idDescriptionLongMsg": 1000118,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -64,18 +78,24 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000119,
+               "idDescriptionLongMsg": 1000120,
                "sMessageId": ""
             },
             {
                "sValue": "DROP_WASTE",
                "sDescriptionShort": "Drop waste",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000121,
+               "idDescriptionLongMsg": 1000122,
                "sMessageId": ""
             },
             {
                "sValue": "KEEP_WASTE_ATTACHED",
                "sDescriptionShort": "Keep waste attached",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000123,
+               "idDescriptionLongMsg": 1000124,
                "sMessageId": ""
             }
          ]
@@ -86,6 +106,8 @@
          "sValue": "false",
          "sDescriptionShort": "Disable dicing",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000125,
+         "idDescriptionLongMsg": 1000126,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -96,6 +118,8 @@
          "sValue": "false",
          "sDescriptionShort": "Prioritize machining speed over quality",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000127,
+         "idDescriptionLongMsg": 1000128,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -106,6 +130,8 @@
          "sValue": "5",
          "sDescriptionShort": "Strip width",
          "sDescriptionLong": "In case the waste is still kept attached, this is the wigth dimension of the strip",
+         "idDescriptionShortMsg": 1000129,
+         "idDescriptionLongMsg": 1000130,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -116,6 +142,8 @@
          "sValue": "true",
          "sDescriptionShort": "Clean blade radius with mill",
          "sDescriptionLong": "Clean blade radius with mill",
+         "idDescriptionShortMsg": 1000131,
+         "idDescriptionLongMsg": 1000132,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -126,6 +154,8 @@
          "sValue": "1",
          "sDescriptionShort": "Milling offset from side",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000133,
+         "idDescriptionLongMsg": 1000134,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"

Strategies/Standard/STR0005/STR0005.lua

@@ -66,7 +66,7 @@ function STR0005.Make( bAddMachining, Proc, Part, CustomParameters)
    local dQualityAddedFace = 0
 
    -- più di 3 facce non supportate
-   if Proc.nFct > 3 then
+   if Proc.nFct > 3 and ( not Proc.Topology.sFamily == 'DoubleBevel') then
       Strategy.Result = FeatureLib.GetStrategyResultNotApplicable( 'More than 3 faces not supported')
    end
 

Strategies/Standard/STR0006/STR0006.json

@@ -8,6 +8,8 @@
          "sValue": "0",
          "sDescriptionShort": "Overmaterial on tenon length",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000135,
+         "idDescriptionLongMsg": 1000136,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "0",
          "sDescriptionShort": "Overmaterial on tenon width",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000137,
+         "idDescriptionLongMsg": 1000138,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "3",
          "sDescriptionShort": "Maximum number of milling passes",
          "sDescriptionLong": "Maximum number of milling passes. If more passes are required, pocketing is performed",
+         "idDescriptionShortMsg": 1000139,
+         "idDescriptionLongMsg": 1000140,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -38,6 +44,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Cutting Strategy",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000141,
+         "idDescriptionLongMsg": 1000142,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -45,24 +53,32 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000143,
+               "idDescriptionLongMsg": 1000144,
                "sMessageId": ""
             },
             {
                "sValue": "BLADE_FORCED",
                "sDescriptionShort": "Blade only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000145,
+               "idDescriptionLongMsg": 1000146,
                "sMessageId": ""
             },
             {
                "sValue": "MILL_FORCED",
                "sDescriptionShort": "Mill only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000147,
+               "idDescriptionLongMsg": 1000148,
                "sMessageId": ""
             },
             {
                "sValue": "CHAINSAW_FORCED",
                "sDescriptionShort": "ChainSaw only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000149,
+               "idDescriptionLongMsg": 1000150,
                "sMessageId": ""
             }
          ]
@@ -73,6 +89,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine the tenon",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000151,
+         "idDescriptionLongMsg": 1000152,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",

Strategies/Standard/STR0007/STR0007.json

@@ -8,6 +8,8 @@
          "sValue": "0",
          "sDescriptionShort": "Overmaterial on Mortise length",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000153,
+         "idDescriptionLongMsg": 1000154,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "0",
          "sDescriptionShort": "Overmaterial on Mortise width",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000155,
+         "idDescriptionLongMsg": 1000156,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "3",
          "sDescriptionShort": "Maximum number of milling passes",
          "sDescriptionLong": "Maximum number of milling passes. If more passes are required, pocketing is performed",
+         "idDescriptionShortMsg": 1000157,
+         "idDescriptionLongMsg": 1000158,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -38,6 +44,8 @@
          "sValue": "true",
          "sDescriptionShort": "Use DoveTail tool in case of pocketing",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000159,
+         "idDescriptionLongMsg": 1000160,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -48,6 +56,8 @@
          "sValue": "true",
          "sDescriptionShort": "Add Anti-Splint",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000161,
+         "idDescriptionLongMsg": 1000162,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -58,6 +68,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Cutting Strategy",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000163,
+         "idDescriptionLongMsg": 1000164,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -65,24 +77,32 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000165,
+               "idDescriptionLongMsg": 1000166,
                "sMessageId": ""
             },
             {
                "sValue": "BLADE_FORCED",
                "sDescriptionShort": "Blade only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000167,
+               "idDescriptionLongMsg": 1000168,
                "sMessageId": ""
             },
             {
                "sValue": "MILL_FORCED",
                "sDescriptionShort": "Mill only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000169,
+               "idDescriptionLongMsg": 1000170,
                "sMessageId": ""
             },
             {
                "sValue": "CHAINSAW_FORCED",
                "sDescriptionShort": "ChainSaw only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000171,
+               "idDescriptionLongMsg": 1000172,
                "sMessageId": ""
             }
          ]
@@ -93,6 +113,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine the mortise cut surface",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000173,
+         "idDescriptionLongMsg": 1000174,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",
@@ -104,6 +126,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine the dovetail mortise",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000175,
+         "idDescriptionLongMsg": 1000176,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",

Strategies/Standard/STR0007/STR0007.lua

@@ -441,7 +441,7 @@ function STR0007.Make( bAddMachining, Proc, Part, CustomParameters)
       local ptCutC, vtCutN = EgtSurfTmFacetCenter( Proc.id, 1, GDB_ID.ROOT)
       if ptCutC and vtCutN and AreSameVectorApprox( Proc.FeatureInfo.vtMortiseN, vtCutN) then
          -- recupero gruppo per geometria addizionale
-         local nAddGrpId = Part.idTempGroup
+         local nAddGrpId = BeamLib.GetAddGroup( Part.id)
          Strategy.idMortiseCutPlane = EgtSurfTmPlaneInBBox( nAddGrpId, ptCutC, vtCutN, Part.b3Part, GDB_RT.GLOB)
       end
    end

Strategies/Standard/STR0008/STR0008.json

@@ -8,6 +8,8 @@
          "sValue": "0",
          "sDescriptionShort": "Overmaterial on mortise length",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000177,
+         "idDescriptionLongMsg": 1000178,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "0",
          "sDescriptionShort": "Overmaterial on mortise width",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000179,
+         "idDescriptionLongMsg": 1000180,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Cutting Strategy",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000181,
+         "idDescriptionLongMsg": 1000182,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -35,24 +41,32 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000183,
+               "idDescriptionLongMsg": 1000184,
                "sMessageId": ""
             },
             {
                "sValue": "BLADE_FORCED",
                "sDescriptionShort": "Blade only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000185,
+               "idDescriptionLongMsg": 1000186,
                "sMessageId": ""
             },
             {
                "sValue": "MILL_FORCED",
                "sDescriptionShort": "Mill only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000187,
+               "idDescriptionLongMsg": 1000188,
                "sMessageId": ""
             },
             {
                "sValue": "CHAINSAW_FORCED",
                "sDescriptionShort": "ChainSaw only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000189,
+               "idDescriptionLongMsg": 1000190,
                "sMessageId": ""
             }
          ]
@@ -63,6 +77,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine the mortise cut surface",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000191,
+         "idDescriptionLongMsg": 1000192,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",
@@ -74,6 +90,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine the mortise",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000193,
+         "idDescriptionLongMsg": 1000194,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",

Strategies/Standard/STR0008/STR0008.lua

@@ -311,11 +311,13 @@ function STR0008.Make( bAddMachining, Proc, Part, CustomParameters)
       -- si applicano le lavorazioni di svuotatura
       for i = 1, #Strategy.Machining.Pocketing do
          if Strategy.Machining.Pocketing[i].bIsApplicable then
-            Pocketing = {}
-            Pocketing.Steps = {}
-            Pocketing.LeadIn = {}
-            Pocketing.nType = MCH_MY.POCKETING
-            Pocketing.nSubType = MCH_POCK_SUB.SPIRALOUT
+            Pocketing = MachiningLib.InitMachiningParameters( MCH_MY.POCKETING)
+            -- se mortasa aperta su un lato si usa SpiralIn
+            if ( Proc.AffectedFaces.bFront or Proc.AffectedFaces.bBack) and ( Proc.AffectedFaces.bTop or Proc.AffectedFaces.bBottom) then
+               Pocketing.nSubType = MCH_POCK_SUB.SPIRALIN
+            else
+               Pocketing.nSubType = MCH_POCK_SUB.SPIRALOUT
+            end
             Pocketing.LeadIn.nType = MCH_POCK_LI.ZIGZAG
             Pocketing.Steps.dStep = TOOLS[Strategy.Machining.Pocketing[i].ToolInfo.nToolIndex].dStep
             Pocketing.Steps.dSideStep = TOOLS[Strategy.Machining.Pocketing[i].ToolInfo.nToolIndex].dSideStep

Strategies/Standard/STR0009/STR0009.json

@@ -1,6 +1,6 @@
 {
    "sStrategyId": "STR0009",
-   "sStrategyName": "Mill Heading",
+   "sStrategyName": "ScarfJoint",
    "ParameterList" : [
       {
          "sName": "dDepthChamfer",
@@ -8,46 +8,32 @@
          "sValue": "0",
          "sDescriptionShort": "Depth Chamfer",
          "sDescriptionLong": "Depth of the V-Mill to execute chamfers on cut-edges",
+         "idDescriptionShortMsg": 1000195,
+         "idDescriptionLongMsg": 1000196,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
       },
       {
-         "sName": "dOverMaterial",
-         "sNameNge": "OVERMAT",
-         "sValue": "0",
-         "sDescriptionShort": "Overmaterial",
-         "sDescriptionLong": "",
-         "sType": "d",
-         "sMessageId": " ",
-         "sMinUserLevel": "1"
-      },
-      {
-         "sName": "bForceStrip",
-         "sNameNge": "FORCE_STRIP",
+         "sName": "bAntiSplint",
+         "sNameNge": "ANTISPLINT",
          "sValue": "false",
-         "sDescriptionShort": "Force strip",
-         "sDescriptionLong": "Enable the parameter to force the software to leave a strip to sustain the piece",
+         "sDescriptionShort": "Use Anti-Splint strategy",
+         "sDescriptionLong": "The strategy will apply blade cuts on corner to avoid wood splint",
+         "idDescriptionShortMsg": 1000197,
+         "idDescriptionLongMsg": 1000198,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
       },
-      {
-         "sName": "dStripWidth",
-         "sNameNge": "STRIP_WIDTH",
-         "sValue": "0",
-         "sDescriptionShort": "Strip width",
-         "sDescriptionLong": "Width of the strip in case if foreseen from the machining",
-         "sType": "d",
-         "sMessageId": " ",
-         "sMinUserLevel": "1"
-      },
       {
          "sName": "sMillingList",
          "sNameNge": "PROFILE_TOOL_LIST",
          "sValue": "",
          "sDescriptionShort": "Available mill to machine the profile",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000199,
+         "idDescriptionLongMsg": 1000200,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",

Strategies/Standard/STR0009/STR0009.lua

@@ -1,7 +1,6 @@
 -- Strategia: STR0009
 -- Descrizione 
--- Fresatura di contorno
--- Feature tipo Arco
+-- Feature tipo ScarfJoint
 
 
 -- carico librerie
@@ -10,156 +9,182 @@ local BeamData = require( 'BeamDataNew')
 local MachiningLib = require( 'MachiningLib')
 local FeatureLib = require( 'FeatureLib')
 -- strategie di base
-local BladeToWaste = require('BLADETOWASTE')
+local BladeToWaste = require( 'BLADETOWASTE')
+local FaceByMill = require( 'FACEBYMILL')
+local FaceByBlade = require( 'FACEBYBLADE')
+local AntiSplintOnFace = require( 'ANTISPLINTONFACE')
 
 -- Tabella per definizione modulo
 local STR0009 = {}
 local Strategy = {}
 
 -------------------------------------------------------------------------------------------------------------
--- TODO gestire il caso in cui non si trova l'utensile
-local function GetArcStrategy( Proc, Part)
-   local Machining = {}
-   local ToolSearchParameters = {}
+local function GetFacesIdOrder( Proc, Part)
+   local Faces = {}
+   if Proc.nFct == 5 then
+      -- carico gli id delle facce
+      for i = 1, Proc.nFct do
+         Faces[#Faces + 1] = BeamLib.TableCopyDeep( Proc.Faces[i])
+      end
+   elseif Proc.nFct == 4 then
+      local vtN1 = Proc.Faces[1].vtN
+      local vtN2 = Proc.Faces[2].vtN
+      local nIndex = EgtIf( abs( vtN1:getX()) > abs( vtN2:getX()), 1, 2)
+      for i = nIndex, Proc.nFct do
+         Faces[#Faces + 1] = BeamLib.TableCopyDeep( Proc.Faces[i])
+      end
+   -- TODO manca il caso in cui mancano facce 4 e 5
+   else -- Proc.nFct == 3
+      for i = 2, Proc.nFct do
+         Faces[#Faces + 1] = BeamLib.TableCopyDeep( Proc.Faces[i])
+      end
+   end
 
-   -- recupero e verifico l'entità curva
-   local idAux = EgtGetInfo( Proc.id, 'AUXID', 'i')
-   if idAux then idAux = idAux + Proc.id end
-   if not idAux  or  ( EgtGetType( idAux) & GDB_FY.GEO_CURVE) == 0 then
-      local sErr = 'Error on process ' .. tostring( Proc.id) .. ' missing profile geometry'
+   return Faces
+end
+
+-------------------------------------------------------------------------------------------------------------
+local function GetEdgeToMachine( ClosingFace, idBottomFace)
+   local EdgeToMachine
+
+   for i = 1, #ClosingFace.Edges do
+      if ClosingFace.Edges[i].idAdjacentFace == idBottomFace then
+         EdgeToMachine = ClosingFace.Edges[i]
+         break
+      end
+   end
+
+   return EdgeToMachine
+end
+
+-------------------------------------------------------------------------------------------------------------
+local function GetScarfJointStrategy( Proc, Part)
+   -- ordino le facce in base al loro numero e al parallelismo delle due facce principali
+   -- faccia 0: superficie tappo (*potrebbe non esserci)
+   -- faccia 1: superficie principale di fondo
+   -- faccia 2: superficie opposta alla faccia 1
+   -- faccia 3: superficie principale superiore
+   -- faccia 4: superficie di testa (*potrebbe non esserci)
+   -- creo una tabella unica contenente tutte le lavorazioni
+   local Result = {}
+   local Cutting = { Machinings = {}, Result = {}}
+   local AntiSplints = {}
+   local Pocketing = {}
+
+   Result.dTimeToMachine = 0
+   local Faces = GetFacesIdOrder( Proc)
+   -- taglio su faccia 4
+   if Faces[4] and Faces[4].vtN then
+      -- recupero gruppo per geometria addizionale
+      local nAddGrpId = BeamLib.GetAddGroup( Part.id)
+      -- TODO la nuova faccia creata sulla 4 può tagliare faccia 1. In caso tagliasse faccia 1, bisogna calcolare i cubetti con 2 facce 
+      Strategy.idFeatureCutPlane = EgtSurfTmPlaneInBBox( nAddGrpId, Faces[4].ptCenter, Faces[4].vtN, Part.b3Part, GDB_RT.GLOB)
+      Cutting.Machinings, Cutting.Result = BladeToWaste.Make( Strategy.idFeatureCutPlane, Part)
+      if Cutting.Result.sStatus == 'Completed' then
+         Cutting.Machinings.bIsApplicable = true
+      end
+   end
+
+   -- antischeggia facce 1 e 3
+   local bAreAllAntisplintsApplicable = true
+   if Strategy.Parameters.bAntiSplint then
+      AntiSplints = AntiSplintOnFace.Make( Proc, Part, Faces[2])
+      for k = 1, #AntiSplints do
+         if not AntiSplints[k].bIsApplicable then
+            bAreAllAntisplintsApplicable = false
+            break
+         end
+      end
+   end
+
+   -- svuotatura faccia 2
+   if Faces[2] then
+      local frPock, dL, dW = EgtSurfTmFacetMinAreaRectangle( Proc.id, Faces[2].id, GDB_ID.ROOT)
+      local ToolSearchParameters = {}
+      ToolSearchParameters.sMillShape = 'STANDARD'
+      ToolSearchParameters.vtToolDirection = Faces[2].vtN
+      ToolSearchParameters.dElevation = abs( ( Faces[2].ptCenter - Faces[4].ptCenter) * Faces[2].vtN)
+      ToolSearchParameters.dMaxToolDiameter = min( dL, dW)
+      ToolSearchParameters.ToolInfo = {}
+      ToolSearchParameters.ToolInfo = MachiningLib.FindMill( Proc, ToolSearchParameters)
+      if ToolSearchParameters.ToolInfo.nToolIndex then
+         local Machining = MachiningLib.InitMachiningParameters( MCH_MY.POCKETING)
+         Machining.Geometry = {{ Proc.id, Faces[2].id}}
+         Machining.dElevation = ToolSearchParameters.dElevation
+         Machining.dMaxElev = Machining.dElevation
+         Machining.vtToolDirection = ToolSearchParameters.vtToolDirection
+         Machining.nSubType = MCH_POCK_SUB.SPIRALIN
+         Machining.LeadIn.nType = MCH_POCK_LI.ZIGZAG
+         Machining.Steps.dStep = TOOLS[ToolSearchParameters.ToolInfo.nToolIndex].dStep
+         Machining.Steps.dSideStep = TOOLS[ToolSearchParameters.ToolInfo.nToolIndex].dSideStep
+         Machining.nToolIndex = ToolSearchParameters.ToolInfo.nToolIndex
+         Machining.LeadIn.dTangentDistance = TOOLS[ToolSearchParameters.ToolInfo.nToolIndex].dDiameter / 2
+         Machining.LeadIn.dElevation = TOOLS[ToolSearchParameters.ToolInfo.nToolIndex].dDiameter / 2
+         Machining.sDepth = 0
+         Machining.dResidualDepth = ToolSearchParameters.ToolInfo.dResidualDepth
+         -- TODO vedere se questo parametro con svuotature nuove si può rimuovere
+         Machining.dOpenMinSafe = Strategy.Parameters.dOpenMinSafe
+         Machining.dTimeToMachine = MachiningLib.GetTimeToMachineAllStepsWithLeadInOut( Machining, Part)
+         Result.dTimeToMachine = Result.dTimeToMachine + Machining.dTimeToMachine
+         table.insert( Pocketing, Machining)
+         Pocketing.bIsApplicable = true
+         -- se non sono stati fatti i passaggi antischeggia si verifica che le facce siano a 90°, altrimenti serve passaggio con fresa
+         if not Strategy.Parameters.bAntiSplint or not bAreAllAntisplintsApplicable then
+            local dAngleBetweenFaces = Proc.AdjacencyMatrix[1][2] or 0
+            -- si fa passaggio con fresa
+            if dAngleBetweenFaces > -90 then
+               local EdgeToMachine = GetEdgeToMachine( Faces[1], Faces[2].id)
+               local CuttingClosingFace = FaceByBlade.Make( Proc, Part, Faces[1], EdgeToMachine)
+               if CuttingClosingFace.bIsApplicable then
+                  table.insert( AntiSplints, CuttingClosingFace)
+               end
+            end
+         end
+      end
+   end
+
+   -- se manca taglio principale, feature non eseguibile
+   if not Cutting.Machinings.bIsApplicable then
+      local sErr = 'Feature '.. Proc.idFeature .. ' : strategy ' .. Strategy.sName .. ' not applicable'
       EgtOutLog( sErr)
-      return false, sErr
-   end
-   Proc.idAddAuxGeom = idAux
-
-   -- recupero i dati della curva e del profilo
-   local dDepth = abs( EgtCurveThickness( idAux))
-   local vtExtr = EgtCurveExtrusion( idAux, GDB_RT.GLOB)
-   local bToolInvert = ( vtExtr:getZ() < -0.1)
-   local bIsHorizontal = abs( vtExtr:getZ()) < 10 * GEO.EPS_SMALL
-   local bIsFeatureDown = Proc.AffectedFaces.bBottom and not Proc.AffectedFaces.bTop
-   local bIsFeatureBack = Proc.AffectedFaces.bBack and not Proc.AffectedFaces.bFront
-   local bForceStrip = Strategy.Parameters.bForceStrip
-   local dDimStrip = EgtIf( Strategy.Parameters.dStripWidth < 100 * GEO.EPS_SMALL, nil, Strategy.Parameters.dStripWidth)
-
-   local bExecStrip = false
-   -- se la lavorazione si trova nella parte inferiore o in battuta dietro, il codolo va sempre lasciato
-   if bIsFeatureDown or bIsFeatureBack or bForceStrip then
-      if bIsFeatureDown or bIsFeatureBack then
-         dDimStrip = dDimStrip or max( BeamData.DIM_STRIP or 5, 5)
-      else
-         dDimStrip = dDimStrip or max( BeamData.DIM_STRIP_SMALL or 5, 1)
-      end
-      bExecStrip = true
-   end
-   if not bExecStrip then
-      dDimStrip = 0
-   end
-
-   -- se lavorazione orizzontale
-   if bIsHorizontal then
-      local bDouble
-      local Milling = MachiningLib.InitMachiningParameters( MCH_MY.MILLING)
-      Milling.bIsApplicable = false
-      ToolSearchParameters = {}
-      ToolSearchParameters.sMillShape = 'STANDARD'
-      ToolSearchParameters.dElevation = EgtIf( bExecStrip, ( dDepth - dDimStrip) / 2, dDepth + BeamData.MILL_OVERLAP)
-      ToolSearchParameters.vtToolDirection = EgtIf( bToolInvert, -vtExtr, vtExtr)
-      ToolSearchParameters.AvailableToolList = MachiningLib.GetAvailableToolList( Proc, Strategy.Parameters.sMillingList, 'Milling')
-      Milling.ToolInfo = {}
-      Milling.ToolInfo = MachiningLib.FindMill( Proc, ToolSearchParameters)
-      -- se posso lavorare in una passata, ma utensile trovato non completa la lavorazione,
-      -- allora provo a cercare utensile con massimo materiale sufficiente per fare le due passate, magari trova un utensile più prestante
-      if Milling.ToolInfo.dResidualDepth > 10 * GEO.EPS_SMALL and not bExecStrip then
-         bDouble = true
-         ToolSearchParameters.dElevation = ( dDepth + BeamData.MILL_OVERLAP) / 2
-         ToolSearchParameters.vtToolDirection = EgtIf( bToolInvert, -vtExtr, vtExtr)
-      end
-      Milling.bToolInvert = bToolInvert
-      Milling.vtToolDirection = vtExtr
-
-      if bDouble or bExecStrip then
-         if bDouble then
-            Milling.sDepth = ( dDepth + BeamData.MILL_OVERLAP) / 2
-         else
-            Milling.sDepth = ( dDepth - dDimStrip) / 2
-         end
-         table.insert( Machining, Milling)
-         local Milling2 = BeamLib.TableCopyDeep( Milling)
-         table.insert( Machining, Milling2)
-      else
-         Milling.sDepth = dDepth + BeamData.MILL_OVERLAP
-         table.insert( Machining, Milling)
-      end
-   -- se lavorazione verticale
+      Result = FeatureLib.GetStrategyResultNotApplicable( sErr)
    else
-      -- si cerca utensile 1
-      local Milling = {}
-      Milling.bIsApplicable = false
-      ToolSearchParameters = {}
-      ToolSearchParameters.sMillShape = 'STANDARD'
-      ToolSearchParameters.dElevation = dDepth + BeamData.MILL_OVERLAP
-      ToolSearchParameters.vtToolDirection = EgtIf( bToolInvert, -vtExtr, vtExtr)
-      ToolSearchParameters.AvailableToolList = MachiningLib.GetAvailableToolList( Proc, Strategy.Parameters.sMillingList, 'Milling')
-      Milling.ToolInfo = {}
-      Milling.ToolInfo = MachiningLib.FindMill( Proc, ToolSearchParameters)
-      -- si cerca utensile 2
-      local Milling2 = {}
-      Milling2.bIsApplicable = false
-      ToolSearchParameters = {}
-      ToolSearchParameters.sMillShape = 'STANDARD'
-      ToolSearchParameters.dElevation = dDepth + BeamData.MILL_OVERLAP
-      ToolSearchParameters.vtToolDirection = EgtIf( bToolInvert, vtExtr, -vtExtr)
-      ToolSearchParameters.AvailableToolList = MachiningLib.GetAvailableToolList( Proc, Strategy.Parameters.sMillingList, 'Milling')
-      Milling2.ToolInfo = {}
-      Milling2.ToolInfo = MachiningLib.FindMill( Proc, ToolSearchParameters)
-
-      -- se serve codolo
-      if bExecStrip then
-         -- se a disposizione entrambi gli utensili
-         if Milling.ToolInfo.nToolIndex and Milling2.ToolInfo.nToolIndex then
-            table.insert( Machining, Milling)
-            table.insert( Machining, Milling2)
-         -- se disponibile solo primo utensile
-         elseif Milling.ToolInfo.nToolIndex then
-            table.insert( Machining, Milling)
-         -- se disponibile solo secondo utensile
-         elseif Milling2.ToolInfo.nToolIndex then
-            table.insert( Machining, Milling2)
-         -- nessun utensile disponibile
+      local dCompletionPercentage = 100
+      -- completa se svuotatura eseguita e antisplit eseguiti (o non richiesti)
+      if Pocketing.bIsApplicable and ( bAreAllAntisplintsApplicable or not Strategy.Parameters.bAntiSplint) then
+         Result.sStatus = 'Completed'
+         if bAreAllAntisplintsApplicable then
+            Result.dQuality = FeatureLib.GetStrategyQuality( 'FINE')
          else
-         -- non si fa nulla
+            Result.dQuality = FeatureLib.GetStrategyQuality( 'STD')
          end
-      -- altrimenti senza codolo
+      -- altrimenti non completa
       else
-         -- se utensile 1 esegue completamente
-         if Milling.ToolInfo.nToolIndex and Milling.ToolInfo.dResidualDepth < 10 * GEO.EPS_SMALL then
-            table.insert( Machining, Milling)
-         -- se utensile 2 esegue completamente
-         elseif Milling2.ToolInfo.nToolIndex and Milling2.ToolInfo.dResidualDepth < 10 * GEO.EPS_SMALL then
-            table.insert( Machining, Milling2)
-         -- se possono lavorare entrambi
-         elseif Milling.ToolInfo.nToolIndex and Milling2.ToolInfo.nToolIndex then
-            table.insert( Machining, Milling)
-            table.insert( Machining, Milling2)
-         -- se utensile 1 non completo
-         elseif Milling.ToolInfo.nToolIndex then
-            table.insert( Machining, Milling)
-            -- se utensile 2 non completo
-         elseif Milling2.ToolInfo.nToolIndex then
-            table.insert( Machining, Milling2)
+         Result.dQuality = FeatureLib.GetStrategyQuality( 'STD')
+         Result.sStatus = 'Not-Completed'
+         -- se fa solo svuotatura
+         if Pocketing.bIsApplicable then
+            dCompletionPercentage = 90
+            Result.sInfo = 'Anti-Split not executed'
+         elseif Strategy.Parameters.bAntiSplint and bAreAllAntisplintsApplicable then
+            dCompletionPercentage = 75
+            Result.sInfo = 'Pocketing not executed'
+         else
+            dCompletionPercentage = 50
+            Result.sInfo = 'Only the cut has been executed'
          end
       end
+
+      Result.dCompletionIndex = FeatureLib.GetFeatureCompletionIndex( dCompletionPercentage)
    end
 
-   -- TODO VOTO DA FARE!!!!
-   Strategy.Result.sStatus = 'Completed'
-   Strategy.Result.dCompletionIndex = 5
-   Strategy.Result.dMRR = MachiningLib.GetToolMRR( Machining[1].ToolInfo or Machining[2].ToolInfo)
-   Strategy.Result.dQuality = FeatureLib.GetStrategyQuality( 'MILL')
-   Strategy.Result.sInfo = ''
+   -- creo una tabella unica contenente tutte le lavorazioni
+   local Machinings = {}
+   EgtJoinTables( Machinings, Cutting.Machinings)
+   EgtJoinTables( Machinings, AntiSplints)
+   EgtJoinTables( Machinings, Pocketing)
 
-   return Machining
+   return Machinings, Result
 end
 
 -------------------------------------------------------------------------------------------------------------
@@ -173,79 +198,33 @@ function STR0009.Make( bAddMachining, Proc, Part, CustomParameters)
    Strategy.Result = {}
 
    local bAreAllMachiningsAdded = true
-   local Milling = {}
 
-   Strategy.Machinings = GetArcStrategy( Proc, Part)
+   -- controlli preliminari
+   if Proc.nFct < 3 or Proc.nFct > 5 then
+      local sErr = 'Feature '.. Proc.idFeature .. ' : strategy ' .. StrategyLib.Config.sStrategyId .. ' not applicable'
+      EgtOutLog( sErr)
+      Strategy.Result = FeatureLib.GetStrategyResultNotApplicable( sErr)
+      return false, Strategy.Result
+   end
 
-   if bAddMachining and Strategy.Result.sStatus ~= 'Not-Applicable' then
-      -- eventuali punti di spezzatura
-      local FeatureSplittingPoints = FeatureLib.GetFeatureSplittingPoints( Proc, Part)
+   Strategy.Machinings, Strategy.Result = GetScarfJointStrategy( Proc, Part)
 
-      for i = 1, #Strategy.Machinings do
-
-         Strategy.Machinings[i].Geometry = {{ Proc.idAddAuxGeom, -1}}
-         Strategy.Machinings[i].nToolIndex = Strategy.Machinings[i].ToolInfo.nToolIndex
-         Strategy.Machinings[i].nType = MCH_MY.MILLING
-         Strategy.Machinings[i].dStartSafetyLength = 0
-         Strategy.Machinings[i].Steps = {}
-         Strategy.Machinings[i].Steps = MachiningLib.GetMachiningSteps( false, tonumber( Strategy.Machinings[i].sDepth), TOOLS[Strategy.Machinings[i].nToolIndex].dStep)
-
-         -- LeadIn / LeadOut
-         Strategy.Machinings[i].LeadIn = {}
-         Strategy.Machinings[i].LeadOut = {}
-         Strategy.Machinings[i].LeadIn.nType = MCH_MILL_LI.TANGENT
-         Strategy.Machinings[i].LeadOut.nType = MCH_MILL_LI.TANGENT
-         Strategy.Machinings[i].LeadIn.dTangentDistance = TOOLS[Strategy.Machinings[i].ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
-         Strategy.Machinings[i].LeadIn.dPerpDistance = 0
-         Strategy.Machinings[i].LeadIn.dStartAddLength = 0
-         Strategy.Machinings[i].LeadOut.dTangentDistance = TOOLS[Strategy.Machinings[i].ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
-         Strategy.Machinings[i].LeadOut.dPerpDistance = 0
-         Strategy.Machinings[i].LeadOut.dEndAddLength = 0
-
-         local dLengthOnX = Proc.b3Box:getDimX()
-         Strategy.bCanMoveAfterSplit = MachiningLib.CanMoveAfterSplitcut( dLengthOnX, Part)
-         if Proc.AffectedFaces.bLeft and Strategy.bCanMoveAfterSplit then
-            Strategy.Machinings[i].sStage = 'AfterTail'
-         end
-
-         -- preparo attacco/uscita in caso di spezzatura arco
-         Strategy.Machinings[i].LeadInForSplit = BeamLib.TableCopyDeep( Strategy.Machinings[i].LeadIn)
-         Strategy.Machinings[i].LeadOutForSplit = BeamLib.TableCopyDeep( Strategy.Machinings[i].LeadOut)
-         Strategy.Machinings[i].LeadInForSplit.nType = MCH_MILL_LI.LINEAR
-         Strategy.Machinings[i].LeadOutForSplit.nType = MCH_MILL_LI.LINEAR
-         Strategy.Machinings[i].LeadInForSplit.dTangentDistance = 0
-         Strategy.Machinings[i].LeadInForSplit.dPerpDistance = TOOLS[Strategy.Machinings[i].ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
-         Strategy.Machinings[i].LeadOutForSplit.dTangentDistance = 0
-         Strategy.Machinings[i].LeadOutForSplit.dPerpDistance = TOOLS[Strategy.Machinings[i].ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
-
-         -- sistemo il lato e la direzione di lavoro
-         if i == 1 then
-            Strategy.Machinings[i].bInvert = EgtIf( TOOLS[Strategy.Machinings[i].ToolInfo.nToolIndex].bIsCCW, false, true)
-            Strategy.Machinings[i].nWorkside = EgtIf( TOOLS[Strategy.Machinings[i].ToolInfo.nToolIndex].bIsCCW, MCH_MILL_WS.RIGHT, MCH_MILL_WS.LEFT)
-         else
-            Strategy.Machinings[i].bToolInvert = true
-            Strategy.Machinings[i].bInvert = EgtIf( TOOLS[Strategy.Machinings[i].ToolInfo.nToolIndex].bIsCCW, true, false)
-            Strategy.Machinings[i].nWorkside = EgtIf( TOOLS[Strategy.Machinings[i].ToolInfo.nToolIndex].bIsCCW, MCH_MILL_WS.RIGHT, MCH_MILL_WS.LEFT)
-         end
-         Strategy.Machinings[i].ptEdge1 = EgtSP( Proc.idAddAuxGeom, GDB_ID.ROOT)
-         Strategy.Machinings[i].ptEdge2 = EgtEP( Proc.idAddAuxGeom, GDB_ID.ROOT)
-         Strategy.Machinings[i].dEdgeLength = EgtCurveLength( Proc.idAddAuxGeom)
-         Strategy.Machinings[i].vtEdgeDirection = EgtSV( Proc.idAddAuxGeom, GDB_ID.ROOT) + EgtMV( Proc.idAddAuxGeom, GDB_ID.ROOT) + EgtEV( Proc.idAddAuxGeom, GDB_ID.ROOT)
-         Strategy.Machinings[i].dLengthOnX = Proc.b3Box:getDimX()
-
-         local MachiningToSplit = {}
-         table.insert( MachiningToSplit, Strategy.Machinings[i])
-         local MachiningResult = MachiningLib.GetSplitMachinings( MachiningToSplit, FeatureSplittingPoints, Part)
+   -- aggiunta lavorazioni
+   if #Strategy.Machinings > 0 then
+      if bAddMachining and Strategy.Result.sStatus ~= 'Not-Applicable' then
          -- aggiunge lavorazione
-         for j = 1, #MachiningResult do
-            bAreAllMachiningsAdded = MachiningLib.AddMachinings( Proc, MachiningResult[j])
+         for j = 1, #Strategy.Machinings do
+            if Proc.AffectedFaces.bLeft then
+               Strategy.Machinings[j].sStage = 'AfterTail'
+            end
+            bAreAllMachiningsAdded = MachiningLib.AddMachinings( Proc, Strategy.Machinings[j])
          end
       end
-
    else
-      bAreAllMachiningsAdded = false
+      Strategy.Result = FeatureLib.GetStrategyResultNotApplicable()
    end
 
+
    return bAreAllMachiningsAdded, Strategy.Result
 end
 

Strategies/Standard/STR0010/STR0010.json

@@ -3,11 +3,13 @@
    "sStrategyName": "Milling",
    "ParameterList" : [
       {
-         "sName": "dAntiSplintWithBlade",
+         "sName": "bAntiSplintWithBlade",
          "sNameNge": "ANTISPLINT_BLADE",
          "sValue": "false",
          "sDescriptionShort": "Antisplint with blade",
          "sDescriptionLong": "Use the blade as antisplint in case the geometry is not through",
+         "idDescriptionShortMsg": 1000201,
+         "idDescriptionLongMsg": 1000202,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -17,7 +19,33 @@
          "sNameNge": "EXTEND_AFTER_TAIL",
          "sValue": "",
          "sDescriptionShort": "Extend after tail",
-         "sDescriptionLong": "The automatism considers this lenght as machinable. This means you accept to damage the next piece in the bar",
+         "sDescriptionLong": "The automatism considers this length as machinable. This means you accept to damage the next piece in the bar",
+         "idDescriptionShortMsg": 1000203,
+         "idDescriptionLongMsg": 1000204,
+         "sType": "d",
+         "sMessageId": " ",
+         "sMinUserLevel": "1"
+      },
+      {
+         "sName": "bFinishWithMill",
+         "sNameNge": "ALLOW_FINISH_MILL",
+         "sValue": "true",
+         "sDescriptionShort": "Clean radius with mill",
+         "sDescriptionLong": "Clean radius with mill",
+         "idDescriptionShortMsg": 1000205,
+         "idDescriptionLongMsg": 1000206,
+         "sType": "b",
+         "sMessageId": " ",
+         "sMinUserLevel": "1"
+      },
+      {
+         "sName": "dMillingOffsetFromSide",
+         "sNameNge": "MILLING_OFFSET_SIDE",
+         "sValue": "1",
+         "sDescriptionShort": "Milling offset from side",
+         "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000207,
+         "idDescriptionLongMsg": 1000208,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +56,8 @@
          "sValue": "NEVER",
          "sDescriptionShort": "Damage next piece",
          "sDescriptionLong": "This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time",
+         "idDescriptionShortMsg": 1000209,
+         "idDescriptionLongMsg": 1000210,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -35,18 +65,24 @@
                "sValue": "NEVER",
                "sDescriptionShort": "Never damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000211,
+               "idDescriptionLongMsg": 1000212,
                "sMessageId": ""
             },
             {
                "sValue": "ONLY_IF_RAWPART",
                "sDescriptionShort": "Damage only if raw",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000213,
+               "idDescriptionLongMsg": 1000214,
                "sMessageId": ""
             },
             {
                "sValue": "ALWAYS",
                "sDescriptionShort": "Can damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000215,
+               "idDescriptionLongMsg": 1000216,
                "sMessageId": ""
             }
          ]

Strategies/Standard/STR0010/STR0010.lua

@@ -9,7 +9,9 @@ local BeamData = require( 'BeamDataNew')
 local MachiningLib = require( 'MachiningLib')
 local FeatureLib = require( 'FeatureLib')
 -- strategie di base
-local FaceByMill = require('FACEBYMILL')
+local FaceByMill = require( 'FACEBYMILL')
+local FaceByBlade = require( 'FACEBYBLADE')
+local AntiSplintOnFace = require( 'ANTISPLINTONFACE')
 
 -- Tabella per definizione modulo
 local STR0010 = {}
@@ -34,7 +36,7 @@ local function GetStrategyCompletionPercentage( Machinings)
       if nWeightsCount ~= 0  and  nWeightsCount ~= i then
          error( 'GetWeightedCompletionPercentage : inconsistent weights')
       end
-      local dWeightedCompletionPercentage = Machining.dCompletionPercentage / 100 * dWeight
+      local dWeightedCompletionPercentage = ( Machining.dCompletionPercentage or 0) / 100 * dWeight
       if Machining.bIsApplicable then
          dCompletionPercentageNumerator = dCompletionPercentageNumerator + dWeightedCompletionPercentage
       end
@@ -47,34 +49,52 @@ local function GetStrategyCompletionPercentage( Machinings)
 end
 
 -------------------------------------------------------------------------------------------------------------
-local function CompareEdges( EdgeA, EdgeB)
-   -- prima i lati orientati lungo X
-   if abs( EdgeA.vtN:getX()) < abs( EdgeB.vtN:getX()) - 10 * GEO.EPS_SMALL then
+local function CompareEdgesLongestTop( EdgeA, EdgeB)
+   -- si preferiscono i lati più lunghi
+   if EdgeA.dLength > EdgeB.dLength + 10 * GEO.EPS_SMALL then
       return true
-   elseif abs( EdgeA.vtN:getX()) > abs( EdgeB.vtN:getX()) + 10 * GEO.EPS_SMALL then
+   elseif EdgeA.dLength < EdgeB.dLength - 10 * GEO.EPS_SMALL then
       return false
-   -- se stessa X si preferiscono i lati più lunghi (nel caso di 5 lati è quello non spezzato)
+   -- se stessa lunghezza si preferiscono i lati più in basso
    else
-      if EdgeA.dLength > EdgeB.dLength + 10 * GEO.EPS_SMALL then
+      if EdgeA.vtN:getZ() > EdgeB.vtN:getZ() + 10 * GEO.EPS_SMALL then
          return true
-      elseif EdgeA.dLength < EdgeB.dLength - 10 * GEO.EPS_SMALL then
+      elseif EdgeA.vtN:getZ() < EdgeB.vtN:getZ() - 10 * GEO.EPS_SMALL then
          return false
-      -- se stessa lunghezza si preferiscono i lati più in basso
-      -- TODO qui dipenderà dalla lama scelta
+      -- se stessa Z si preferiscono i lati verso il fronte della trave
       else
-         if EdgeA.vtN:getZ() > EdgeB.vtN:getZ() + 10 * GEO.EPS_SMALL then
+         if EdgeA.vtN:getY() > EdgeB.vtN:getY() + 10 * GEO.EPS_SMALL then
             return true
-         elseif EdgeA.vtN:getZ() < EdgeB.vtN:getZ() - 10 * GEO.EPS_SMALL then
+         elseif EdgeA.vtN:getY() < EdgeB.vtN:getY() - 10 * GEO.EPS_SMALL then
             return false
-         -- se stessa Z si preferiscono i lati verso il fronte della trave
          else
-            if EdgeA.vtN:getY() > EdgeB.vtN:getY() + 10 * GEO.EPS_SMALL then
-               return true
-            elseif EdgeA.vtN:getY() < EdgeB.vtN:getY() - 10 * GEO.EPS_SMALL then
-               return false
-            else
-               return false
-            end
+            return false
+         end
+      end
+   end
+end
+
+-------------------------------------------------------------------------------------------------------------
+local function CompareEdgesLongestBottom( EdgeA, EdgeB)
+   -- si preferiscono i lati più lunghi
+   if EdgeA.dLength > EdgeB.dLength + 10 * GEO.EPS_SMALL then
+      return true
+   elseif EdgeA.dLength < EdgeB.dLength - 10 * GEO.EPS_SMALL then
+      return false
+   -- se stessa lunghezza si preferiscono i lati più in alto
+   else
+      if EdgeA.vtN:getZ() < EdgeB.vtN:getZ() - 10 * GEO.EPS_SMALL then
+         return true
+      elseif EdgeA.vtN:getZ() > EdgeB.vtN:getZ() + 10 * GEO.EPS_SMALL then
+         return false
+      -- se stessa Z si preferiscono i lati verso il fronte della trave
+      else
+         if EdgeA.vtN:getY() > EdgeB.vtN:getY() + 10 * GEO.EPS_SMALL then
+            return true
+         elseif EdgeA.vtN:getY() < EdgeB.vtN:getY() - 10 * GEO.EPS_SMALL then
+            return false
+         else
+            return false
          end
       end
    end
@@ -93,7 +113,7 @@ end
 
 -------------------------------------------------------------------------------------------------------------
 -- TODO modificare funzione e verificare pinzaggio con regioni e area outline
-local function IsPositionOK( Proc, Part)
+local function IsPositionOk( Proc, Part)
    local bIsFeatureLong = FeatureLib.IsMachiningLong( Proc.b3Box:getDimX(), Part, { dMaxSegmentLength = BeamData.LONGCUT_ENDLEN})
    -- se impatta su faccia retro o sotto, controllo fattibilità
    if Proc.AffectedFaces.bBack then
@@ -112,31 +132,24 @@ local function IsPositionOK( Proc, Part)
 end
 
 -------------------------------------------------------------------------------------------------------------
--- TODO da sistemare
-local function GetBottomFaceEdge( Proc, nIndexFace)
+local function GetLongEdgeToMachine( Face, bHeadType)
    local Edge = {}
 
-   -- si lavora la bottom longitudinalmente
-   if Proc.nFct == 1 or Proc.Topology.sFamily == 'DoubleBevel' then
-      local BottomEdgesSorted = {}
-      for i = 1, #Proc.MainFaces.BottomFaces[nIndexFace].Edges do
-         table.insert( BottomEdgesSorted, Proc.MainFaces.BottomFaces[nIndexFace].Edges[i])
-      end
-      table.sort( BottomEdgesSorted, CompareEdges)
-      Edge = BottomEdgesSorted[1]
-   -- edge in comune tra le due facce
-   elseif Proc.nFct == 2 then
-      if nIndexFace == 1 then
-         Edge = Proc.MainFaces.BottomFaces[nIndexFace].MainEdges.LongEdges[1]
-      elseif nIndexFace == 2 then
-         Edge = Proc.MainFaces.BottomFaces[nIndexFace].MainEdges.BottomEdge
-      end
+   local EdgesSorted = {}
+   for i = 1, #Face.Edges do
+      table.insert( EdgesSorted, Face.Edges[i])
+   end
+   if bHeadType.bBottom then
+      table.sort( EdgesSorted, CompareEdgesLongestBottom)
    else
-      if nIndexFace == 1 then
-         Edge = Proc.MainFaces.BottomFaces[nIndexFace].MainEdges.LongEdges[1]
-      elseif nIndexFace == 2 then
-         Edge = Proc.MainFaces.BottomFaces[nIndexFace].MainEdges.BottomEdge
-      end
+      table.sort( EdgesSorted, CompareEdgesLongestTop)
+   end
+
+   -- se il lato migliore è accessibile si sceglie questo, altrimenti il lato opposto; se entrambi non accessibili (faccia chiusa da due lati) si mantiene il lato scelto
+   Edge = EdgesSorted[1]
+   local EdgeOpposite = BeamLib.FindEdgeBestOrientedAsDirection( Face.Edges, -Edge.vtN)
+   if ( not EdgeOpposite.bIsOpen) and Edge.bIsOpen then
+      Edge = EdgeOpposite
    end
 
    return Edge
@@ -148,15 +161,28 @@ local function SortMachiningsBySegment( MachiningA, MachiningB)
       return false
    elseif MachiningB.nFeatureSegment > MachiningA.nFeatureSegment then
       return true
+   -- se segmento uguale, si guarda la priorità
    else
-      if TOOLS[ MachiningA.nToolIndex].sFamily == 'SAWBLADE' and TOOLS[ MachiningB.nToolIndex].sFamily == 'MORTISE' then
-         return true
-      elseif TOOLS[ MachiningA.nToolIndex].sFamily == 'MORTISE' and TOOLS[ MachiningB.nToolIndex].sFamily == 'SAWBLADE' then
+      if MachiningA.nInternalSortingPriority > MachiningB.nInternalSortingPriority then
          return false
+      elseif MachiningB.nInternalSortingPriority > MachiningA.nInternalSortingPriority then
+         return true
+      -- se priorità uguale, si minimizzano i cambi di lato
       else
-         if MachiningA.sEdgeType == 'Side' and MachiningB.sEdgeType ~= 'Side' then
-            return true
-         elseif MachiningB.sEdgeType == 'Side' and MachiningA.sEdgeType ~= 'Side' then
+         local bIsOddSegment = ( MachiningA.nFeatureSegment % 2 ~= 0)
+         if MachiningA.vtToolDirection:getY() < MachiningB.vtToolDirection:getY() - 10 * GEO.EPS_SMALL then
+            if bIsOddSegment then
+               return true
+            else
+               return false
+            end
+         elseif MachiningA.vtToolDirection:getY() > MachiningB.vtToolDirection:getY() + 10 * GEO.EPS_SMALL then
+            if bIsOddSegment then
+               return false
+            else
+               return true
+            end
+         else
             return false
          end
       end
@@ -172,6 +198,7 @@ function STR0010.Make( bAddMachining, Proc, Part, CustomParameters)
    Strategy.Parameters = BeamLib.LoadCustomParametersInStrategy( Proc, Part, CustomParameters, StrategyLib.Config)
    Strategy.Machinings = {}
    Strategy.Result = {}
+   local CalculatedMachinings = {}
 
    -- controllo su topologia
    if not IsTopologyOk( Proc) then
@@ -181,7 +208,7 @@ function STR0010.Make( bAddMachining, Proc, Part, CustomParameters)
 
    -- controllo dimensioni solo se non è forzata
    if not CustomParameters.bForcedStrategy then
-      if not IsPositionOK( Proc, Part) then
+      if not IsPositionOk( Proc, Part) then
          Strategy.Result = FeatureLib.GetStrategyResultNotApplicable( 'Feature not machinable in this position')
          return false, Strategy.Result
       end
@@ -198,8 +225,6 @@ function STR0010.Make( bAddMachining, Proc, Part, CustomParameters)
    -- volume della feature
    local dFeatureVolume = Proc.dVolume
 
-   -- TODO taglio su eventuali facce di chiusura
-
    -- eventuali punti di spezzatura
    local FeatureSplittingPoints = FeatureLib.GetFeatureSplittingPoints( Proc, Part)
    local bIsSplitFeature = false
@@ -212,45 +237,167 @@ function STR0010.Make( bAddMachining, Proc, Part, CustomParameters)
       dExtendAfterTail = 10000
    end
 
-   -- lavorazione della BottomFace
    local bAreAllMachiningsAdded = true
-   local Milling = {}
-   local OptionalParametersFaceByMill = { nStepType = MCH_MILL_ST.ONEWAY, bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail}
-   local EdgeToMachine = GetBottomFaceEdge( Proc, 1)
-   if EdgeToMachine.bIsOpen then
-      OptionalParametersFaceByMill.dDepthToMachine = EdgeToMachine.dElevation + BeamData.CUT_EXTRA
-   end
-   Milling = FaceByMill.Make( Proc, Part, Proc.MainFaces.BottomFaces[1], EdgeToMachine, OptionalParametersFaceByMill)
-   if Milling.bIsApplicable then
-      table.insert( Strategy.Machinings, Milling)
+
+   -- ricerca delle Bottom (la principale deve avere 4 lati esatti)
+   local BottomFace1 = Proc.MainFaces.BottomFaces[1]
+   local BottomFace2 = Proc.MainFaces.BottomFaces[2]
+   if #BottomFace1.Edges ~= 4 then
+      Strategy.Result = FeatureLib.GetStrategyResultNotApplicable()
+      return false, Strategy.Result
    end
 
-   -- si lavora seconda BottomFace
-   if Proc.Topology.sFamily == 'DoubleBevel' or Proc.Topology.sName == 'Rabbet-2-Through' or Proc.Topology.sName == 'Bevel-2-Blind' then
-      local dAngleBetweenFaces = Proc.AdjacencyMatrix[1][2]
-      -- se convesso o concavo maggiore di angolo retto
-      if dAngleBetweenFaces >= -91 then
-         Milling = {}
-         OptionalParametersFaceByMill = { nStepType = MCH_MILL_ST.ONEWAY, bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail}
-         EdgeToMachine = GetBottomFaceEdge( Proc, 2)
-         if EdgeToMachine.bIsOpen then
-            OptionalParametersFaceByMill.dDepthToMachine = EdgeToMachine.dElevation + BeamData.CUT_EXTRA
+   -- ricerca utensile
+   local ToolSearchParameters = {}
+   ToolSearchParameters.dElevation = BottomFace1.dElevation
+   ToolSearchParameters.vtToolDirection = BottomFace1.vtN
+   ToolSearchParameters.bAllowTopHead = true
+   ToolSearchParameters.bAllowBottomHead = true
+   ToolSearchParameters.sMillShape = 'STANDARD'
+   local ToolInfo = MachiningLib.FindMill( Proc, ToolSearchParameters)
+   local nToolIndex = ToolInfo.nToolIndex
+
+   -- se utensile non trovato si esce subito
+   if not TOOLS[nToolIndex] or not TOOLS[nToolIndex].sName then
+      local sMessage = 'Mill not found'
+      Strategy.Result = FeatureLib.GetStrategyResultNotApplicable( sMessage)
+      return false, Strategy.Result
+   end
+
+   -- per prima si lavora sempre la Bottom principale
+   local Milling1 = {}
+   local OptionalParametersMilling1 = { nStepType = MCH_MILL_ST.ONEWAY, bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail}
+   local BottomEdgeToMachine1 = GetLongEdgeToMachine( BottomFace1, TOOLS[nToolIndex].SetupInfo.HeadType)
+   if BottomEdgeToMachine1.bIsOpen then
+      OptionalParametersMilling1.dDepthToMachine = BottomEdgeToMachine1.dElevation + BeamData.CUT_EXTRA
+   end
+   Milling1 = FaceByMill.Make( Proc, Part, BottomFace1, BottomEdgeToMachine1, OptionalParametersMilling1)
+   Milling1.nInternalSortingPriority = 2
+   Milling1.dResultWeight = 0.3
+   table.insert( CalculatedMachinings, Milling1)
+
+   -- se necessario si lavora la seconda Bottom (solo se ha 4 lati esatti)
+   local Milling2
+   local BottomEdgeToMachine2
+   if BottomFace2 then
+      local dAngleBetweenFaces = Proc.AdjacencyMatrix[BottomFace1.id + 1][BottomFace2.id + 1]
+      if dAngleBetweenFaces >= -89.5 then
+         Milling2 = {}
+         if #BottomFace2.Edges == 4 then
+            local OptionalParametersMilling2 = { nStepType = MCH_MILL_ST.ONEWAY, bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail}
+            BottomEdgeToMachine2 = GetLongEdgeToMachine( BottomFace2, TOOLS[nToolIndex].SetupInfo.HeadType)
+            if BottomEdgeToMachine2.bIsOpen then
+               OptionalParametersMilling2.dDepthToMachine = BottomEdgeToMachine2.dElevation + BeamData.CUT_EXTRA
+            end
+            Milling2 = FaceByMill.Make( Proc, Part, BottomFace2, BottomEdgeToMachine2, OptionalParametersMilling2)
+            Milling2.nInternalSortingPriority = 2
+            Milling2.dResultWeight = 0.3
+         else
+            Milling2.bIsApplicable = false
          end
-         Milling = FaceByMill.Make( Proc, Part, Proc.MainFaces.BottomFaces[2], EdgeToMachine, OptionalParametersFaceByMill)
-         if Milling.bIsApplicable then
-            table.insert( Strategy.Machinings, Milling)
+         table.insert( CalculatedMachinings, Milling2)
+      end
+   end
+
+   -- fresatura eventuali facce di chiusura (se non già lavorate)
+   -- TODO funzione
+   if Strategy.Parameters.bFinishWithMill then
+
+      if Milling1 then
+         -- si recuperano i lati chiusi non lavorati
+         local EdgesClosedNotMachined = {}
+         for i = 1, #BottomFace1.Edges do
+            if not( ( BottomFace1.Edges[i].id == BottomEdgeToMachine1.id) or BottomFace1.Edges[i].bIsOpen) then
+               table.insert( EdgesClosedNotMachined, BottomFace1.Edges[i])
+            end
+         end
+         -- su ognuno si fa la fresatura di pulizia
+         for i = 1, #EdgesClosedNotMachined do
+            local dMillingOffsetFromSide = Strategy.Parameters.bAntiSplintWithBlade and Strategy.Parameters.dMillingOffsetFromSide or 0
+            local dDepthToMachine = EdgesClosedNotMachined[i].dElevation - dMillingOffsetFromSide
+            local dToolMarkLength = Milling1.dToolMarkLength or 0
+            local OptionalParameters = {
+               bIsSplitFeature = bIsSplitFeature,
+               dExtendAfterTail = dExtendAfterTail,
+               dRadialStepSpan = dToolMarkLength,
+               dDepthToMachine = dDepthToMachine
+            }
+            local Milling = FaceByMill.Make( Proc, Part, BottomFace1, EdgesClosedNotMachined[i], OptionalParameters)
+            Milling.nInternalSortingPriority = 3
+            Milling.dResultWeight = 0.05
+            table.insert( CalculatedMachinings, Milling)
+         end
+      end
+
+      if Milling2 then
+         -- si recuperano i lati chiusi non lavorati
+         local EdgesClosedNotMachined = {}
+         for i = 1, #BottomFace2.Edges do
+            if not( ( BottomFace2.Edges[i].id == BottomEdgeToMachine2.id) or BottomFace2.Edges[i].bIsOpen) then
+               table.insert( EdgesClosedNotMachined, BottomFace2.Edges[i])
+            end
+         end
+         -- su ognuno si fa la fresatura di pulizia
+         for i = 1, #EdgesClosedNotMachined do
+            local dMillingOffsetFromSide = Strategy.Parameters.bAntiSplintWithBlade and Strategy.Parameters.dMillingOffsetFromSide or 0
+            local dDepthToMachine = EdgesClosedNotMachined[i].dElevation - dMillingOffsetFromSide
+            local dToolMarkLength = Milling2.dToolMarkLength or 0
+            local OptionalParameters = {
+               bIsSplitFeature = bIsSplitFeature,
+               dExtendAfterTail = dExtendAfterTail,
+               dRadialStepSpan = dToolMarkLength,
+               dDepthToMachine = dDepthToMachine
+            }
+            local Milling = FaceByMill.Make( Proc, Part, BottomFace2, EdgesClosedNotMachined[i], OptionalParameters)
+            Milling.nInternalSortingPriority = 3
+            Milling.dResultWeight = 0.05
+            table.insert( CalculatedMachinings, Milling)
          end
       end
    end
 
-   -- calcolo completamento, serve la lista di lavorazioni che comprende le non applicabili
-   Strategy.Result.dCompletionPercentage = GetStrategyCompletionPercentage( Strategy.Machinings)
+   -- antischeggia sulle facce di chiusura delle facce lavorate
+   local CalculatedMachiningsNoAntisplint = BeamLib.TableCopyDeep( CalculatedMachinings)
+   if Strategy.Parameters.bAntiSplintWithBlade then
+
+      local OptionalParametersAntiSplint = {
+         bIsSplitFeature = bIsSplitFeature,
+         dExtendAfterTail = dExtendAfterTail,
+         nInternalSortingPriority = 1,
+         dResultWeight = 0.15
+      }
+      local AntiSplints1 = AntiSplintOnFace.Make( Proc, Part, BottomFace1, OptionalParametersAntiSplint)
+      for i = 1, #AntiSplints1 do
+         table.insert( CalculatedMachinings, AntiSplints1[i])
+      end
+      if Milling2 then
+         local AntiSplints2 = AntiSplintOnFace.Make( Proc, Part, BottomFace2, OptionalParametersAntiSplint)
+         for i = 1, #AntiSplints2 do
+            table.insert( CalculatedMachinings, AntiSplints2[i])
+         end
+      end
+   end
+
+   -- calcolo completamento, serve la lista di lavorazioni che comprende le non applicabili, ma non gli antischeggia (quelle alzano la qualità e sono già contemplate)
+   Strategy.Result.dCompletionPercentage = GetStrategyCompletionPercentage( CalculatedMachiningsNoAntisplint)
    Strategy.Result.dCompletionIndex = FeatureLib.GetFeatureCompletionIndex( Strategy.Result.dCompletionPercentage)
 
+   -- lavorazioni da applicare spostate in lista finale
+   for i = 1, #CalculatedMachinings do
+      if CalculatedMachinings[i].bIsApplicable then
+         table.insert( Strategy.Machinings, CalculatedMachinings[i])
+      end
+   end
+
    Strategy.Machinings = MachiningLib.GetSplitMachinings( Strategy.Machinings, FeatureSplittingPoints, Part)
    table.sort( Strategy.Machinings, SortMachiningsBySegment)
 
-   Strategy.Result.dQuality = FeatureLib.GetStrategyQuality( Strategy.Machinings)
+   -- se non ci sono lati chiusi, la qualità è migliore
+   if Proc.Topology.sName == 'Bevel-1-Through' or Proc.Topology.sName == 'DoubleBevel-2-Through' or Proc.Topology.sName == 'Cut-1-Through' then
+      Strategy.Result.dQuality = FeatureLib.GetStrategyQuality( 'FINE')
+   else
+      Strategy.Result.dQuality = FeatureLib.GetStrategyQuality( Strategy.Machinings)
+   end
    Strategy.Result.dTimeToMachine = FeatureLib.GetStrategyTimeToMachine( Strategy.Machinings)
    Strategy.Result.dMRR = ( dFeatureVolume / Strategy.Result.dTimeToMachine) / pow( 10, 6)
    if Strategy.Result.dCompletionPercentage > 100 - 10 * GEO.EPS_SMALL then

Strategies/Standard/STR0011/STR0011.json

@@ -8,6 +8,8 @@
          "sValue": "0",
          "sDescriptionShort": "Tolerance on Diameter",
          "sDescriptionLong": "Tolerance on Diameter",
+         "idDescriptionShortMsg": 1000217,
+         "idDescriptionLongMsg": 1000218,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "0",
          "sDescriptionShort": "Depth PreHole",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000219,
+         "idDescriptionLongMsg": 1000220,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Drilling Mode",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000221,
+         "idDescriptionLongMsg": 1000222,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -35,18 +41,24 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000223,
+               "idDescriptionLongMsg": 1000224,
                "sMessageId": ""
             },
             {
                "sValue": "PREFER_ONE",
                "sDescriptionShort": "Preferred machining from one side only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000225,
+               "idDescriptionLongMsg": 1000226,
                "sMessageId": ""
             },
             {
                "sValue": "FORCE_TWO",
                "sDescriptionShort": "Force machining from two sides",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000227,
+               "idDescriptionLongMsg": 1000228,
                "sMessageId": ""
             }
          ]
@@ -57,6 +69,8 @@
          "sValue": "",
          "sDescriptionShort": "Available Drillbit list",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000229,
+         "idDescriptionLongMsg": 1000230,
          "sType": "tool",
          "sSubType": "MCH_TF.DRILLBIT",
          "sMessageId": " ",

Strategies/Standard/STR0011/STR0011.lua

@@ -16,6 +16,27 @@ local Strategy = {}
 
 -- TODO Da fare completamente gestione foratura doppia con 2 teste
 
+-------------------------------------------------------------------------------------------------------------
+local function GetSCC( vtMachiningDirection)
+   -- TODO implementare SCC come per FacesBySaw
+   local nSCC = MCH_SCC.NONE
+   if vtMachiningDirection:getZ() < -0.9 then
+      nSCC = MCH_SCC.ADIR_ZM
+   elseif vtMachiningDirection:getZ() > 0.9 then
+      nSCC = MCH_SCC.ADIR_ZP
+   elseif vtMachiningDirection:getY() < -0.707 then
+      nSCC = MCH_SCC.ADIR_YM
+   elseif vtMachiningDirection:getY() > 0.707 then
+      nSCC = MCH_SCC.ADIR_YP
+   elseif vtMachiningDirection:getX() < -0.707 then
+      nSCC = MCH_SCC.ADIR_XM
+   elseif vtMachiningDirection:getX() > 0.707 then
+      nSCC = MCH_SCC.ADIR_XP
+   end
+
+   return nSCC
+end
+
 -------------------------------------------------------------------------------------------------------------
 local function GetDrillingStrategy( Proc, Part)
    local ToolSearchParameters = {}
@@ -39,6 +60,7 @@ local function GetDrillingStrategy( Proc, Part)
       Drilling.nToolIndex = Drilling.ToolInfo.nToolIndex
       Drilling.vtToolDirection = Proc.FeatureInfo.vtDrillExtrusion
       Drilling.dStep = TOOLS[Drilling.nToolIndex].dStep
+      Drilling.nSCC = GetSCC( -Drilling.vtToolDirection)
    end
 
    -- TODO se utensile 2 che si torverà è il gemello da usare nelle lavorazioni in doppio, allora gestire di conseguenza l'applicazione delle lavorazioni in doppio
@@ -61,6 +83,7 @@ local function GetDrillingStrategy( Proc, Part)
          Drilling2.bInvert = true
          Drilling2.vtToolDirection = -Proc.FeatureInfo.vtDrillExtrusion
          Drilling2.dStep = TOOLS[Drilling2.nToolIndex].dStep
+         Drilling2.nSCC = GetSCC( -Drilling2.vtToolDirection)
       end
    end
 

Strategies/Standard/STR0012/STR0012.json

@@ -7,7 +7,9 @@
          "sNameNge": "EXTEND_AFTER_TAIL",
          "sValue": "",
          "sDescriptionShort": "Extend after tail",
-         "sDescriptionLong": "The automatism considers this lenght as machinable. This means you accept to damage the next piece in the bar",
+         "sDescriptionLong": "The automatism considers this length as machinable. This means you accept to damage the next piece in the bar",
+         "idDescriptionShortMsg": 1000231,
+         "idDescriptionLongMsg": 1000232,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "NEVER",
          "sDescriptionShort": "Damage next piece",
          "sDescriptionLong": "This option allows you to decide how to consider the next piece in the bar. The software calculates specifics LeadIn/out to respect the parameter. This parameter may change the machining time",
+         "idDescriptionShortMsg": 1000233,
+         "idDescriptionLongMsg": 1000234,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -25,18 +29,24 @@
                "sValue": "NEVER",
                "sDescriptionShort": "Never damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000235,
+               "idDescriptionLongMsg": 1000236,
                "sMessageId": ""
             },
             {
                "sValue": "ONLY_IF_RAWPART",
                "sDescriptionShort": "Damage only if raw",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000237,
+               "idDescriptionLongMsg": 1000238,
                "sMessageId": ""
             },
             {
                "sValue": "ALWAYS",
                "sDescriptionShort": "Can damage",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000239,
+               "idDescriptionLongMsg": 1000240,
                "sMessageId": ""
             }
          ]
@@ -47,6 +57,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Ridge Lap strategy",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000241,
+         "idDescriptionLongMsg": 1000242,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -54,18 +66,24 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000243,
+               "idDescriptionLongMsg": 1000244,
                "sMessageId": ""
             },
             {
                "sValue": "BLADE",
                "sDescriptionShort": "Use blade",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000245,
+               "idDescriptionLongMsg": 1000246,
                "sMessageId": ""
             },
             {
                "sValue": "MILL",
                "sDescriptionShort": "Use mill",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000247,
+               "idDescriptionLongMsg": 1000248,
                "sMessageId": ""
             }
          ]

Strategies/Standard/STR0013/STR0013.json

@@ -8,6 +8,8 @@
          "sValue": "0",
          "sDescriptionShort": "Tolerance on Diameter",
          "sDescriptionLong": "Tolerance on Diameter",
+         "idDescriptionShortMsg": 1000249,
+         "idDescriptionLongMsg": 1000250,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "0",
          "sDescriptionShort": "Use mill as a drillbit",
          "sDescriptionLong": "Admit to use the mill as a drillbit",
+         "idDescriptionShortMsg": 1000251,
+         "idDescriptionLongMsg": 1000252,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "0",
          "sDescriptionShort": "Execute contour only",
          "sDescriptionLong": "Execute the contour anyway, even the hole is bigger than the tool diameter",
+         "idDescriptionShortMsg": 1000253,
+         "idDescriptionLongMsg": 1000254,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -38,6 +44,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Drilling mode",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000255,
+         "idDescriptionLongMsg": 1000256,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -45,18 +53,24 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000257,
+               "idDescriptionLongMsg": 1000258,
                "sMessageId": ""
             },
             {
                "sValue": "PREFER_ONE",
                "sDescriptionShort": "Preferred machining from one side only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000259,
+               "idDescriptionLongMsg": 1000260,
                "sMessageId": ""
             },
             {
                "sValue": "FORCE_TWO",
                "sDescriptionShort": "Force machining from two sides",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000261,
+               "idDescriptionLongMsg": 1000262,
                "sMessageId": ""
             }
          ]
@@ -67,6 +81,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine drills",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000263,
+         "idDescriptionLongMsg": 1000264,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",

Strategies/Standard/STR0013/STR0013.lua

@@ -14,6 +14,27 @@ local FeatureLib = require( 'FeatureLib')
 local STR0013 = {}
 local Strategy = {}
 
+-------------------------------------------------------------------------------------------------------------
+local function GetSCC( vtMachiningDirection)
+   -- TODO implementare SCC come per FacesBySaw
+   local nSCC = MCH_SCC.NONE
+   if vtMachiningDirection:getZ() < -0.9 then
+      nSCC = MCH_SCC.ADIR_ZM
+   elseif vtMachiningDirection:getZ() > 0.9 then
+      nSCC = MCH_SCC.ADIR_ZP
+   elseif vtMachiningDirection:getY() < -0.707 then
+      nSCC = MCH_SCC.ADIR_YM
+   elseif vtMachiningDirection:getY() > 0.707 then
+      nSCC = MCH_SCC.ADIR_YP
+   elseif vtMachiningDirection:getX() < -0.707 then
+      nSCC = MCH_SCC.ADIR_XM
+   elseif vtMachiningDirection:getX() > 0.707 then
+      nSCC = MCH_SCC.ADIR_XP
+   end
+
+   return nSCC
+end
+
 -------------------------------------------------------------------------------------------------------------
 local function GetDrillingWithMillStrategy( Proc, Part)
    local ToolSearchParameters = {}
@@ -74,7 +95,7 @@ local function GetDrillingWithMillStrategy( Proc, Part)
          HalfMilling2.ToolInfo = MachiningLib.FindMill( Proc, ToolSearchParameters)
 
          -- se entrambi gli utensili lavorano in modo completo fino alla metà del foro, li sostituisco a qeulli trovati in precedenza
-         if HalfMilling.ToolInfo.dResidualDepth < 0 and HalfMilling2.ToolInfo.dResidualDepth < 0 then
+         if HalfMilling.ToolInfo.dResidualDepth and HalfMilling2.ToolInfo.dResidualDepth and HalfMilling.ToolInfo.dResidualDepth < 0 and HalfMilling2.ToolInfo.dResidualDepth < 0 then
             if Milling.ToolInfo.nToolIndex ~= HalfMilling.ToolInfo.nToolIndex then
                Milling.ToolInfo.nToolIndex, Milling.ToolInfo.dResidualDepth = HalfMilling.ToolInfo.nToolIndex, HalfMilling.ToolInfo.dResidualDepth
             end
@@ -172,6 +193,7 @@ function STR0013.Make( bAddMachining, Proc, Part, CustomParameters)
             MachiningToAdd = MachiningLib.InitMachiningParameters( MCH_MY.DRILLING)
             MachiningToAdd = BeamLib.MergeTables( MachiningToAdd, Strategy.Machinings[j])
             MachiningToAdd.Steps.dStep = TOOLS[nIndexTool].dStep / 3
+            MachiningToAdd.nSCC = GetSCC( -MachiningToAdd.vtToolDirection)
          -- se diametro foro più grande della fresa, ma non oltre il doppio del diametro, si fa contornatura a spirale
          elseif Proc.FeatureInfo.dDrillDiam < ( TOOLS[nIndexTool].dDiameter * 0.75) * 2 or Strategy.Parameters.bOnlyContouring then
             MachiningToAdd = MachiningLib.InitMachiningParameters( MCH_MY.MILLING)
@@ -184,6 +206,7 @@ function STR0013.Make( bAddMachining, Proc, Part, CustomParameters)
             MachiningToAdd.LeadOut.dTangentDistance = 0.5
             MachiningToAdd.LeadOut.dPerpDistance = 0.5
             MachiningToAdd.LeadOut.dElevation = Proc.FeatureInfo.dDrillLen
+            MachiningToAdd.nSCC = GetSCC( -MachiningToAdd.vtToolDirection)
          -- se diametro foro più grande del doppio del diametro fresa, si fa svuotatura
          else
             MachiningToAdd = MachiningLib.InitMachiningParameters( MCH_MY.POCKETING)
@@ -194,6 +217,7 @@ function STR0013.Make( bAddMachining, Proc, Part, CustomParameters)
             MachiningToAdd.LeadIn.nType = MCH_POCK_LI.HELIX
             MachiningToAdd.LeadIn.dTangentDistance = TOOLS[nIndexTool].dDiameter / 2
             MachiningToAdd.LeadIn.dElevation = MachiningToAdd.Steps.dStep / 2
+            MachiningToAdd.nSCC = GetSCC( -MachiningToAdd.vtToolDirection)
          end
 
          MachiningToAdd.nToolIndex = nIndexTool

Strategies/Standard/STR0014/STR0014.json

@@ -8,6 +8,8 @@
          "sValue": "1",
          "sDescriptionShort": "Machining Depth",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000265,
+         "idDescriptionLongMsg": 1000266,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine mark and text",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000267,
+         "idDescriptionLongMsg": 1000268,
          "sType": "tool",
          "sSubType": "MCH_TF.MILL",
          "sMessageId": " ",
@@ -29,6 +33,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Marking Strategy",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000269,
+         "idDescriptionLongMsg": 1000270,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -36,18 +42,24 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000271,
+               "idDescriptionLongMsg": 1000272,
                "sMessageId": ""
             },
             {
                "sValue": "PEN_FORCED",
                "sDescriptionShort": "Pen only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000273,
+               "idDescriptionLongMsg": 1000274,
                "sMessageId": ""
             },
             {
                "sValue": "VMILL_FORCED",
                "sDescriptionShort": "V-Mill only",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000275,
+               "idDescriptionLongMsg": 1000276,
                "sMessageId": ""
             }
          ]

Strategies/Standard/STR0014/STR0014.lua

@@ -24,6 +24,8 @@ local function GetSCC( Machining)
 
    if TOOLS[Machining.nToolIndex].SetupInfo.bToolOnAggregate then
       nSCC = MCH_SCC.ADIR_NEAR
+   elseif TOOLS[Machining.nToolIndex].SetupInfo.nBlockedSCC then
+      nSCC = TOOLS[Machining.nToolIndex].SetupInfo.nBlockedSCC
    elseif Machining.vtToolDirection:getY() <= 0 then
       nSCC = MCH_SCC.ADIR_YM
    else
@@ -96,7 +98,7 @@ function STR0014.Make( bAddMachining, Proc, Part, CustomParameters)
          Strategy.Machining.nSCC = GetSCC( Strategy.Machining)
 
          Strategy.Machining.nType = MCH_MY.MILLING
-         Strategy.Machining.sDepth = EgtClamp( Strategy.Parameters.dMachiningDepth, -1, 5)
+         Strategy.Machining.sDepth = EgtClamp( Strategy.Parameters.dMachiningDepth, -1, TOOLS[Strategy.Machining.nToolIndex].dMaxMaterial)
          Strategy.Machining.nWorkside = MCH_MILL_WS.CENTER
 
          -- LeadIn / LeadOut
@@ -104,12 +106,24 @@ function STR0014.Make( bAddMachining, Proc, Part, CustomParameters)
          Strategy.Machining.LeadOut = {}
          Strategy.Machining.LeadIn.nType = MCH_MILL_LI.NONE
          Strategy.Machining.LeadOut.nType = MCH_MILL_LI.NONE
+         
+         -- se è una penna, si limita la lavorazione per evitare di partire fuori dal grezzo
+         if ToolSearchParameters.sMillShape == 'PEN' then
+             Strategy.Machining.LeadIn.dStartAddLength = -20
+             Strategy.Machining.LeadOut.dEndAddLength = -20
+         end
 
+         -- TODO gestire meglio
+         -- se utensile montato su aggregato flottante
+         if TOOLS[Strategy.Machining.nToolIndex].bToolOnFloatingTH then
+            Strategy.Machining.dMaxElev = Strategy.Parameters.dMachiningDepth
+            Strategy.Machining.dLongitudinalOffset = -5
+         end
          -- stessi parametri cambia solo al geometria
          for i = 1, #Proc.FeatureInfo.AdditionalGeometries do
             local AuxId = Proc.id + Proc.FeatureInfo.AdditionalGeometries[i]
             Strategy.AuxiliaryData.Clones[i+1] = {}
-            Strategy.AuxiliaryData.Clones[i+1].Geometry = EgtSetMachiningGeometry( {{ AuxId, -1}})
+            Strategy.AuxiliaryData.Clones[i+1].Geometry = {{ AuxId, -1}}
          end
 
          bAreAllMachiningsAdded = MachiningLib.AddMachinings( Proc, Strategy.Machining, Strategy.AuxiliaryData)

Strategies/Standard/STR0015/STR0015.json

@@ -8,6 +8,8 @@
          "sValue": "0",
          "sDescriptionShort": "Depth Chamfer",
          "sDescriptionLong": "Depth of the V-Mill to execute chamfers on cut-edges",
+         "idDescriptionShortMsg": 1000277,
+         "idDescriptionLongMsg": 1000278,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "false",
          "sDescriptionShort": "Only Chamfer",
          "sDescriptionLong": "Execute the chamfer only, no other machining",
+         "idDescriptionShortMsg": 1000279,
+         "idDescriptionLongMsg": 1000280,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "0",
          "sDescriptionShort": "Overmaterial",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000281,
+         "idDescriptionLongMsg": 1000282,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -38,6 +44,8 @@
          "sValue": "15",
          "sDescriptionShort": "Max radius left on corners",
          "sDescriptionLong": "Radius-limit left by the tool at each corner of the feature",
+         "idDescriptionShortMsg": 1000283,
+         "idDescriptionLongMsg": 1000284,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -48,6 +56,8 @@
          "sValue": "true",
          "sDescriptionShort": "Execute cut to remove material",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000285,
+         "idDescriptionLongMsg": 1000286,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -58,6 +68,8 @@
          "sValue": "false",
          "sDescriptionShort": "Force strip",
          "sDescriptionLong": "Enable the parameter to force the software to leave a strip to sustain the piece",
+         "idDescriptionShortMsg": 1000287,
+         "idDescriptionLongMsg": 1000288,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -68,6 +80,8 @@
          "sValue": "0",
          "sDescriptionShort": "Strip width",
          "sDescriptionLong": "Width of the strip in case if foreseen from the machining",
+         "idDescriptionShortMsg": 1000289,
+         "idDescriptionLongMsg": 1000290,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -78,6 +92,8 @@
          "sValue": "AUTO",
          "sDescriptionShort": "Cutting Strategy",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000291,
+         "idDescriptionLongMsg": 1000292,
          "sType": "combo",
          "sMinUserLevel": "1",
          "Choices": [
@@ -85,24 +101,32 @@
                "sValue": "AUTO",
                "sDescriptionShort": "Automatic",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000293,
+               "idDescriptionLongMsg": 1000294,
                "sMessageId": ""
             },
             {
                "sValue": "NONE",
                "sDescriptionShort": "No machining",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000295,
+               "idDescriptionLongMsg": 1000296,
                "sMessageId": ""
             },
             {
                "sValue": "BLADE_FORCED",
                "sDescriptionShort": "Blade forced",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000297,
+               "idDescriptionLongMsg": 1000298,
                "sMessageId": ""
             },
             {
                "sValue": "MILL_FORCED",
                "sDescriptionShort": "Mill forced",
                "sDescriptionLong": "",
+               "idDescriptionShortMsg": 1000299,
+               "idDescriptionLongMsg": 1000300,
                "sMessageId": ""
             }
          ]
@@ -113,6 +137,8 @@
          "sValue": "",
          "sDescriptionShort": "Available mill to machine the profile",
          "sDescriptionLong": "",
+         "idDescriptionShortMsg": 1000301,
+         "idDescriptionLongMsg": 1000302,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"

Strategies/Standard/STR0015/STR0015.lua

@@ -704,6 +704,21 @@ local function GetFeatureResult( Proc)
    return Result
 end
 
+-------------------------------------------------------------------------------------------------------------
+local function GetSCC( Proc, vtToolDirection)
+   local nSCC = MCH_SCC.NONE
+
+   if Proc.AffectedFaces.bRight and not Proc.AffectedFaces.bLeft then
+      nSCC = MCH_SCC.ADIR_XP
+   elseif Proc.AffectedFaces.bLeft and not Proc.AffectedFaces.bRight then
+      nSCC = MCH_SCC.ADIR_XM
+   elseif vtToolDirection and AreSameOrOppositeVectorApprox( vtToolDirection, Z_AX()) then
+      nSCC = MCH_SCC.ADIR_YP
+   end
+
+   return nSCC
+end
+
 -------------------------------------------------------------------------------------------------------------
 function STR0015.Make( bAddMachining, Proc, Part, CustomParameters)
    -- carico parametri de default e li aggiorno con quelli passati dal chiamante (potrebbero non essere congruenti)
@@ -814,53 +829,56 @@ function STR0015.Make( bAddMachining, Proc, Part, CustomParameters)
       if Strategy.Profile.Machinings then
          for i = 1, #Strategy.Profile.Machinings do
 
-            Strategy.Profile.Machinings[i].Geometry = {{ Proc.idAddAuxGeom, -1}}
-            Strategy.Profile.Machinings[i].nToolIndex = Strategy.Profile.Machinings[i].ToolInfo.nToolIndex
-            Strategy.Profile.Machinings[i].nType = MCH_MY.MILLING
-            Strategy.Profile.Machinings[i].Steps = MachiningLib.GetMachiningSteps( false, tonumber( Strategy.Profile.Machinings[i].sDepth), TOOLS[Strategy.Profile.Machinings[i].nToolIndex].dStep)
-            Strategy.Profile.Machinings[i].Steps.nStepType = MCH_MILL_ST.ONEWAY
+            local CurrentMachining = Strategy.Profile.Machinings[i]
+
+            CurrentMachining.Geometry = {{ Proc.idAddAuxGeom, -1}}
+            CurrentMachining.nToolIndex = CurrentMachining.ToolInfo.nToolIndex
+            CurrentMachining.nType = MCH_MY.MILLING
+            CurrentMachining.Steps = MachiningLib.GetMachiningSteps( false, tonumber( CurrentMachining.sDepth), TOOLS[CurrentMachining.nToolIndex].dStep)
+            CurrentMachining.Steps.nStepType = MCH_MILL_ST.ONEWAY
+            CurrentMachining.nSCC = GetSCC( Proc, CurrentMachining.vtToolDirection)
 
             -- LeadIn / LeadOut
-            Strategy.Profile.Machinings[i].LeadIn.nType = MCH_MILL_LI.TANGENT
-            Strategy.Profile.Machinings[i].LeadOut.nType = MCH_MILL_LI.TANGENT
-            Strategy.Profile.Machinings[i].LeadIn.dTangentDistance = TOOLS[Strategy.Profile.Machinings[i].ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
-            Strategy.Profile.Machinings[i].LeadIn.dPerpDistance = 0
-            Strategy.Profile.Machinings[i].LeadIn.dStartAddLength = 0
-            Strategy.Profile.Machinings[i].LeadOut.dTangentDistance = TOOLS[Strategy.Profile.Machinings[i].ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
-            Strategy.Profile.Machinings[i].LeadOut.dPerpDistance = 0
-            Strategy.Profile.Machinings[i].LeadOut.dEndAddLength = 0
+            CurrentMachining.LeadIn.nType = MCH_MILL_LI.TANGENT
+            CurrentMachining.LeadOut.nType = MCH_MILL_LI.TANGENT
+            CurrentMachining.LeadIn.dTangentDistance = TOOLS[CurrentMachining.ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
+            CurrentMachining.LeadIn.dPerpDistance = 0
+            CurrentMachining.LeadIn.dStartAddLength = 0
+            CurrentMachining.LeadOut.dTangentDistance = TOOLS[CurrentMachining.ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
+            CurrentMachining.LeadOut.dPerpDistance = 0
+            CurrentMachining.LeadOut.dEndAddLength = 0
 
             if Proc.AffectedFaces.bLeft and Strategy.bCanMoveAfterSplit then
-               Strategy.Profile.Machinings[i].sStage = 'AfterTail'
+               CurrentMachining.sStage = 'AfterTail'
             end
 
             -- preparo attacco/uscita in caso di spezzatura arco
-            Strategy.Profile.Machinings[i].LeadInForSplit = BeamLib.TableCopyDeep( Strategy.Profile.Machinings[i].LeadIn)
-            Strategy.Profile.Machinings[i].LeadOutForSplit = BeamLib.TableCopyDeep( Strategy.Profile.Machinings[i].LeadOut)
-            Strategy.Profile.Machinings[i].LeadInForSplit.nType = MCH_MILL_LI.LINEAR
-            Strategy.Profile.Machinings[i].LeadOutForSplit.nType = MCH_MILL_LI.LINEAR
-            Strategy.Profile.Machinings[i].LeadInForSplit.dTangentDistance = 0
-            Strategy.Profile.Machinings[i].LeadInForSplit.dPerpDistance = TOOLS[Strategy.Profile.Machinings[i].ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
-            Strategy.Profile.Machinings[i].LeadOutForSplit.dTangentDistance = 0
-            Strategy.Profile.Machinings[i].LeadOutForSplit.dPerpDistance = TOOLS[Strategy.Profile.Machinings[i].ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
+            CurrentMachining.LeadInForSplit = BeamLib.TableCopyDeep( CurrentMachining.LeadIn)
+            CurrentMachining.LeadOutForSplit = BeamLib.TableCopyDeep( CurrentMachining.LeadOut)
+            CurrentMachining.LeadInForSplit.nType = MCH_MILL_LI.LINEAR
+            CurrentMachining.LeadOutForSplit.nType = MCH_MILL_LI.LINEAR
+            CurrentMachining.LeadInForSplit.dTangentDistance = 0
+            CurrentMachining.LeadInForSplit.dPerpDistance = TOOLS[CurrentMachining.ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
+            CurrentMachining.LeadOutForSplit.dTangentDistance = 0
+            CurrentMachining.LeadOutForSplit.dPerpDistance = TOOLS[CurrentMachining.ToolInfo.nToolIndex].dDiameter / 2 + BeamData.COLL_SIC
 
             -- sistemo il lato e la direzione di lavoro
-            if Strategy.Profile.Machinings[i].bOtherDirection then
-               Strategy.Profile.Machinings[i].bToolInvert = true
-               Strategy.Profile.Machinings[i].bInvert = EgtIf( TOOLS[Strategy.Profile.Machinings[i].ToolInfo.nToolIndex].bIsCCW, true, false)
-               Strategy.Profile.Machinings[i].nWorkside = EgtIf( TOOLS[Strategy.Profile.Machinings[i].ToolInfo.nToolIndex].bIsCCW, MCH_MILL_WS.RIGHT, MCH_MILL_WS.LEFT)
+            if CurrentMachining.bOtherDirection then
+               CurrentMachining.bToolInvert = true
+               CurrentMachining.bInvert = EgtIf( TOOLS[CurrentMachining.ToolInfo.nToolIndex].bIsCCW, true, false)
+               CurrentMachining.nWorkside = EgtIf( TOOLS[CurrentMachining.ToolInfo.nToolIndex].bIsCCW, MCH_MILL_WS.RIGHT, MCH_MILL_WS.LEFT)
             else
-               Strategy.Profile.Machinings[i].bInvert = EgtIf( TOOLS[Strategy.Profile.Machinings[i].ToolInfo.nToolIndex].bIsCCW, false, true)
-               Strategy.Profile.Machinings[i].nWorkside = EgtIf( TOOLS[Strategy.Profile.Machinings[i].ToolInfo.nToolIndex].bIsCCW, MCH_MILL_WS.RIGHT, MCH_MILL_WS.LEFT)
+               CurrentMachining.bInvert = EgtIf( TOOLS[CurrentMachining.ToolInfo.nToolIndex].bIsCCW, false, true)
+               CurrentMachining.nWorkside = EgtIf( TOOLS[CurrentMachining.ToolInfo.nToolIndex].bIsCCW, MCH_MILL_WS.RIGHT, MCH_MILL_WS.LEFT)
             end
-            Strategy.Profile.Machinings[i].ptEdge1 = EgtSP( Proc.idAddAuxGeom, GDB_ID.ROOT)
-            Strategy.Profile.Machinings[i].ptEdge2 = EgtEP( Proc.idAddAuxGeom, GDB_ID.ROOT)
-            Strategy.Profile.Machinings[i].dEdgeLength = EgtCurveLength( Proc.idAddAuxGeom)
-            Strategy.Profile.Machinings[i].vtEdgeDirection = EgtSV( Proc.idAddAuxGeom, GDB_ID.ROOT) + EgtMV( Proc.idAddAuxGeom, GDB_ID.ROOT) + EgtEV( Proc.idAddAuxGeom, GDB_ID.ROOT)
-            Strategy.Profile.Machinings[i].dLengthOnX = Proc.b3Box:getDimX()
+            CurrentMachining.ptEdge1 = EgtSP( Proc.idAddAuxGeom, GDB_ID.ROOT)
+            CurrentMachining.ptEdge2 = EgtEP( Proc.idAddAuxGeom, GDB_ID.ROOT)
+            CurrentMachining.dEdgeLength = EgtCurveLength( Proc.idAddAuxGeom)
+            CurrentMachining.vtEdgeDirection = EgtSV( Proc.idAddAuxGeom, GDB_ID.ROOT) + EgtMV( Proc.idAddAuxGeom, GDB_ID.ROOT) + EgtEV( Proc.idAddAuxGeom, GDB_ID.ROOT)
+            CurrentMachining.dLengthOnX = Proc.b3Box:getDimX()
 
             local MachiningToSplit = {}
-            table.insert( MachiningToSplit, Strategy.Profile.Machinings[i])
+            table.insert( MachiningToSplit, CurrentMachining)
             local MachiningResult = MachiningLib.GetSplitMachinings( MachiningToSplit, FeatureSplittingPoints, Part)
             -- aggiunge lavorazione
             for j = 1, #MachiningResult do

Strategies/Standard/TAILCUT/TAILCUT.json

@@ -8,6 +8,8 @@
          "sValue": "0",
          "sDescriptionShort": "Depth Chamfer",
          "sDescriptionLong": "Depth of the V-Mill to execute chamfers on cut-edges",
+         "idDescriptionShortMsg": 1000309,
+         "idDescriptionLongMsg": 1000310,
          "sType": "d",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -18,6 +20,8 @@
          "sValue": "false",
          "sDescriptionShort": "Force to use chain saw",
          "sDescriptionLong": "Force to use chain saw",
+         "idDescriptionShortMsg": 1000311,
+         "idDescriptionLongMsg": 1000312,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -28,6 +32,8 @@
          "sValue": "true",
          "sDescriptionShort": "Force to add PreCuts",
          "sDescriptionLong": "Autocam will apply a machining on the theoretical zero, to avoid collision if the theoretical piece length doesn't correspond to the real length",
+         "idDescriptionShortMsg": 1000313,
+         "idDescriptionLongMsg": 1000314,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"
@@ -38,6 +44,8 @@
          "sValue": "true",
          "sDescriptionShort": "Finish with mill",
          "sDescriptionLong": "Use a mill to finish the surface if split with chain saw",
+         "idDescriptionShortMsg": 1000315,
+         "idDescriptionLongMsg": 1000316,
          "sType": "b",
          "sMessageId": " ",
          "sMinUserLevel": "1"

Strategies/Standard/TAILCUT/TAILCUT.lua

@@ -41,6 +41,11 @@ function TAILCUT.Make( bAddMachining, Proc, Part, CustomParameters)
 
    -- si setta che è taglio di coda
    Strategy.bIsTailCut = true
+   -- quando si aggiunge la lavorazione, si cambia il nome della feature
+   if bAddMachining then
+      -- si forza il nome della feature
+      EgtSetName( Proc.id, 'EndCut')
+   end
 
    -- separazione solo se esiste grezzo successivo con pezzi o scaricabile
    Strategy.bSplit = not( Part.bIsLastPart)  or  Part.dRestLength >= BeamData.dMinRaw
@@ -89,9 +94,6 @@ function TAILCUT.Make( bAddMachining, Proc, Part, CustomParameters)
 
    -- se devo applicare le lavorazioni
    if bAddMachining then
-      -- si forza il nome della feature
-      EgtSetName( Proc.id, 'EndCut')
-
       -- inserimento smussi su spigoli del taglio
       if Strategy.Parameters.bMakeChamfer then
          MakeChamfer()

Strategies/Strategies.ini

@@ -7,8 +7,8 @@ STR0004 = Topologia tipo LapJoint. Motosega
 STR0005 = 1, 2 o 3 facce. Lama con taglio singolo o cubetti. Se richiesto o necessario codolo.
 STR0006 = Tenone. Lama + fresa
 STR0007 = Mortasa a coda di rondine e mortasa frontale a coda di rondine
-STR0008 = Svuotatura tasca
-STR0009 = !!DEPRECATA!! Sostituita da STR0015. RIUTILIZZABILE!
+STR0008 = Svuotatura mortasa (raggiata)
+STR0009 = ScarfJoint
 STR0010 = Fresatura perpendicolare (tipo cut, longcut)
 STR0011 = Foratura
 STR0012 = RidgeLap
@@ -79,7 +79,7 @@ STR0015 = Profilo arcuato (Head Cambered Profile)
 ; Feature : French Ridge Lap
 35,1,Feature,
 ; Feature : Chamfer
-36,0,Feature,
+36,0,Feature,STR0002,STR0005,STR0010
 ; Feature : Block Haus Half Lap
 37,0,Feature,
 ; Feature : Block Haus Front

StrategyLibs/ANTISPLINTONFACE.lua

@@ -0,0 +1,55 @@
+-- Strategia: FACEBYBLADE
+-- Descrizione 
+-- Strategia di base per la lavorazione delle facce con lama
+
+-- carico librerie
+local FaceByBlade = require( 'FACEBYBLADE')
+
+-- Tabella per definizione modulo
+local ANTISPLINTONFACE = {}
+
+-------------------------------------------------------------------------------------------------------------
+function ANTISPLINTONFACE.Make( Proc, Part, Face, OptionalParameters)
+   local Machinings = {}
+
+   -- parametri opzionali
+   if not OptionalParameters then
+      OptionalParameters = {}
+   end
+   local bIsSplitFeature = OptionalParameters.bIsSplitFeature or false
+   local dExtendAfterTail = OptionalParameters.dExtendAfterTail or 10000
+   local nInternalSortingPriority = OptionalParameters.nInternalSortingPriority or 1
+   local dResultWeight = OptionalParameters.dResultWeight or 0.15
+   local bMachineAllClosedEdges = OptionalParameters.bMachineAllClosedEdges or false
+
+   local ClosingFacesAgainstGrain = {}
+   for i = 1, #Face.Edges do
+      local CurrentFace = Proc.Faces[Face.Edges[i].idAdjacentFace + 1]
+      if ( not Face.Edges[i].bIsOpen) and ( Face.Edges[i].bIsStartOpen or Face.Edges[i].bIsEndOpen or bMachineAllClosedEdges) then
+         table.insert( ClosingFacesAgainstGrain, CurrentFace)
+      end
+   end
+   for i = 1, #ClosingFacesAgainstGrain do
+      local EdgeToMachine = {}
+      for j = 1, #ClosingFacesAgainstGrain[i].Edges do
+         if ClosingFacesAgainstGrain[i].Edges[j].idAdjacentFace == Face.id then
+            EdgeToMachine = ClosingFacesAgainstGrain[i].Edges[j]
+            break
+         end
+      end
+
+      local Cutting = {}
+      local OptionalParametersFaceByBlade = { bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail}
+      Cutting = FaceByBlade.Make( Proc, Part, ClosingFacesAgainstGrain[i], EdgeToMachine, OptionalParametersFaceByBlade)
+
+      Cutting.nInternalSortingPriority = nInternalSortingPriority
+      Cutting.dResultWeight = dResultWeight
+      table.insert( Machinings, Cutting)
+   end
+
+   return Machinings
+end
+
+-------------------------------------------------------------------------------------------------------------
+
+ return ANTISPLINTONFACE

StrategyLibs/BLADEKEEPWASTE.lua

@@ -14,45 +14,63 @@ local MachiningLib = require( 'MachiningLib')
 local BeamLib = require('BeamLib')
 -- strategie di base
 local FaceByBlade = require('FACEBYBLADE')
-local FaceByMill = require('FACEBYMILL')
+local FaceByMill = require( 'FACEBYMILL')
+local AntiSplintOnFace = require( 'ANTISPLINTONFACE')
 
 -- tabelle per definizione modulo
 
 -------------------------------------------------------------------------------------------------------------
-local function CompareEdges( EdgeA, EdgeB)
-   -- prima i lati orientati lungo X
-   if abs( EdgeA.vtN:getX()) < abs( EdgeB.vtN:getX()) - 10 * GEO.EPS_SMALL then
+local function CompareEdgesLongestTop( EdgeA, EdgeB)
+   -- si preferiscono i lati più lunghi
+   if EdgeA.dLength > EdgeB.dLength + 10 * GEO.EPS_SMALL then
       return true
-   elseif abs( EdgeA.vtN:getX()) > abs( EdgeB.vtN:getX()) + 10 * GEO.EPS_SMALL then
+   elseif EdgeA.dLength < EdgeB.dLength - 10 * GEO.EPS_SMALL then
       return false
-   -- se stessa X si preferiscono i lati più lunghi (nel caso di 5 lati è quello non spezzato)
+   -- se stessa lunghezza si preferiscono i lati più in basso
    else
-      if EdgeA.dLength > EdgeB.dLength + 10 * GEO.EPS_SMALL then
+      if EdgeA.vtN:getZ() > EdgeB.vtN:getZ() + 10 * GEO.EPS_SMALL then
          return true
-      elseif EdgeA.dLength < EdgeB.dLength - 10 * GEO.EPS_SMALL then
+      elseif EdgeA.vtN:getZ() < EdgeB.vtN:getZ() - 10 * GEO.EPS_SMALL then
          return false
-      -- se stessa lunghezza si preferiscono i lati più in basso
-      -- TODO qui dipenderà dalla lama scelta
+      -- se stessa Z si preferiscono i lati verso il fronte della trave
       else
-         if EdgeA.vtN:getZ() > EdgeB.vtN:getZ() + 10 * GEO.EPS_SMALL then
+         if EdgeA.vtN:getY() > EdgeB.vtN:getY() + 10 * GEO.EPS_SMALL then
             return true
-         elseif EdgeA.vtN:getZ() < EdgeB.vtN:getZ() - 10 * GEO.EPS_SMALL then
+         elseif EdgeA.vtN:getY() < EdgeB.vtN:getY() - 10 * GEO.EPS_SMALL then
             return false
-         -- se stessa Z si preferiscono i lati verso il fronte della trave
          else
-            if EdgeA.vtN:getY() > EdgeB.vtN:getY() + 10 * GEO.EPS_SMALL then
-               return true
-            elseif EdgeA.vtN:getY() < EdgeB.vtN:getY() - 10 * GEO.EPS_SMALL then
-               return false
-            else
-               return false
-            end
+            return false
          end
       end
    end
 end
 
 
+local function GetLongEdgeToMachine( Face, bHeadType)
+   local Edge = {}
+
+   local EdgesSorted = {}
+   for i = 1, #Face.Edges do
+      table.insert( EdgesSorted, Face.Edges[i])
+   end
+   table.sort( EdgesSorted, CompareEdgesLongestTop)
+
+   -- se il lato migliore è accessibile si sceglie questo, altrimenti il lato opposto; se entrambi non accessibili (faccia chiusa da due lati) la lavorazione non è applicabile
+   Edge = EdgesSorted[1]
+   local EdgeOpposite = BeamLib.FindEdgeBestOrientedAsDirection( Face.Edges, -Edge.vtN)
+   if not EdgeOpposite.bIsOpen then
+      if Edge.bIsOpen then
+         Edge = EdgeOpposite
+      -- entrambi i lati non accessibili: codolo non applicabile
+      else
+         return nil
+      end
+   end
+
+   return Edge
+end
+
+
 local function SortMachiningsBySegment( MachiningA, MachiningB)
    if MachiningA.nFeatureSegment > MachiningB.nFeatureSegment then
       return false
@@ -118,6 +136,76 @@ local function GetStrategyCompletionPercentage( Machinings)
 end
 
 
+local function MakeBottomFace( Proc, Part, BottomFace, EdgeToMachine, Parameters)
+   local Cuttings = {}
+   local Cutting1 = {}
+   local Cutting2 = {}
+
+   -- parametri dal chiamante
+   local bIsSplitFeature = Parameters.bIsSplitFeature
+   local dExtendAfterTail = Parameters.dExtendAfterTail
+   local nToolIndex = Parameters.nToolIndex
+   local dStripWidth = Parameters.dStripWidth
+   local OtherBottomFace = Parameters.OtherBottomFace
+
+   local dDepthToMachine = EdgeToMachine.dElevation / 2 - dStripWidth / 2
+   local OptionalParametersFaceByBlade1 = { dDepthToMachine = dDepthToMachine, bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail, nToolIndex = nToolIndex}
+   local EdgeToMachineOpposite = BeamLib.FindEdgeBestOrientedAsDirection( BottomFace.Edges, -EdgeToMachine.vtN)
+
+   -- primo lato
+   if EdgeToMachineOpposite.bIsOpen then
+      Cutting1 = FaceByBlade.Make( Proc, Part, BottomFace, EdgeToMachine, OptionalParametersFaceByBlade1)
+   end
+   Cutting1.nInternalSortingPriority = 2
+   Cutting1.dResultWeight = 0.3
+
+   -- secondo lato
+   local OptionalParametersFaceByBlade2 = BeamLib.TableCopyDeep( OptionalParametersFaceByBlade1)
+   OptionalParametersFaceByBlade2.OppositeToolDirectionMode = 'Enabled'
+   if EdgeToMachine.bIsOpen then
+      Cutting2 = FaceByBlade.Make( Proc, Part, BottomFace, EdgeToMachine, OptionalParametersFaceByBlade2)
+   end
+   Cutting2.nInternalSortingPriority = 2
+   Cutting2.dResultWeight = 0.3
+
+   -- se uno dei due lati non è riuscito, si estende il più possibile il lato rimasto
+   if not Cutting1.bIsApplicable and Cutting2.bIsApplicable then
+
+      -- se si lavora il lato in comune con l'altra BottomFace significa ci si deve fermare piú indietro
+      if OtherBottomFace and ( EdgeToMachine.idAdjacentFace == OtherBottomFace.id) then
+         dStripWidth = TOOLS[Cutting2.nToolIndex].dThickness + 2 * dStripWidth
+      end
+      dDepthToMachine = min( TOOLS[Cutting2.nToolIndex].dMaxMaterial, EdgeToMachine.dElevation - dStripWidth)
+      OptionalParametersFaceByBlade2.dDepthToMachine = dDepthToMachine
+
+      Cutting2 = FaceByBlade.Make( Proc, Part, BottomFace, EdgeToMachine, OptionalParametersFaceByBlade2)
+      Cutting2.nInternalSortingPriority = 2
+      Cutting2.dResultWeight = 0.3
+      table.insert( Cuttings, Cutting2)
+
+   elseif not Cutting2.bIsApplicable and Cutting1.bIsApplicable then
+
+      -- se si lavora il lato in comune con l'altra BottomFace significa ci si deve fermare piú indietro
+      if OtherBottomFace and ( EdgeToMachine.idAdjacentFace == OtherBottomFace.id) then
+         dStripWidth = TOOLS[Cutting1.nToolIndex].dThickness + 2 * dStripWidth
+      end
+      dDepthToMachine = min( TOOLS[Cutting1.nToolIndex].dMaxMaterial, EdgeToMachine.dElevation - dStripWidth)
+      OptionalParametersFaceByBlade1.dDepthToMachine = dDepthToMachine
+
+      Cutting1 = FaceByBlade.Make( Proc, Part, BottomFace, EdgeToMachine, OptionalParametersFaceByBlade1)
+      Cutting1.nInternalSortingPriority = 2
+      Cutting1.dResultWeight = 0.3
+      table.insert( Cuttings, Cutting1)
+
+   else
+      table.insert( Cuttings, Cutting1)
+      table.insert( Cuttings, Cutting2)
+   end
+
+   return Cuttings
+end
+
+
 function BLADEKEEPWASTE.Make( Proc, Part, OptionalParameters)
    -- TODO verificare funzionamento con lama da sotto
    -- TODO scelta utensile è corretto lasciarla a FaceByBlade?
@@ -126,30 +214,29 @@ function BLADEKEEPWASTE.Make( Proc, Part, OptionalParameters)
    local Result = {}
    local Machinings = {}
    local CalculatedMachinings = {}
-   local Cutting1 = {}
-   local Cutting2 = {}
 
    -- controlli preventivi
-   if Proc.nFct > 3 then
-      error( 'BladeKeepWaste : max 3 faces supported')
+   if Proc.nFct > 3 and Proc.Topology.sFamily ~= 'DoubleBevel' then
+      Result = FeatureLib.GetStrategyResultNotApplicable( 'BladeKeepWaste : max 3 faces supported')
+      return Machinings, Result
    elseif Proc.nFct == 2 then
       -- per angolo tra le facce >= 90deg (feature convessa) non applicabile
       if Proc.AdjacencyMatrix[1][2] > 10 * GEO.EPS_SMALL or Proc.AdjacencyMatrix[1][2] < -91 then
-         Result = FeatureLib.GetStrategyResultNotApplicable( 'BladeKeepWaste : angle between faces must be concave and >= 90deg')
+         Result = FeatureLib.GetStrategyResultNotApplicable()
          return Machinings, Result
       end
    elseif Proc.nFct == 3 then
       -- caso speciale RidgeLap - per angolo tra le facce >= 90deg (feature convessa) non applicabile
       if Proc.AdjacencyMatrix[1][2] > 10 * GEO.EPS_SMALL or Proc.AdjacencyMatrix[1][2] < -91 then
-         Result = FeatureLib.GetStrategyResultNotApplicable( 'BladeKeepWaste : angle between faces must be concave and >= 90deg')
+         Result = FeatureLib.GetStrategyResultNotApplicable()
          return Machinings, Result
       end
       if Proc.AdjacencyMatrix[1][3] > 10 * GEO.EPS_SMALL or Proc.AdjacencyMatrix[1][3] < -91 then
-         Result = FeatureLib.GetStrategyResultNotApplicable( 'BladeKeepWaste : angle between faces must be concave and >= 90deg')
+         Result = FeatureLib.GetStrategyResultNotApplicable()
          return Machinings, Result
       end
       if Proc.AdjacencyMatrix[2][3] > 10 * GEO.EPS_SMALL or Proc.AdjacencyMatrix[2][3] < -91 then
-         Result = FeatureLib.GetStrategyResultNotApplicable( 'BladeKeepWaste : angle between faces must be concave and >= 90deg')
+         Result = FeatureLib.GetStrategyResultNotApplicable()
          return Machinings, Result
       end
    end
@@ -160,12 +247,7 @@ function BLADEKEEPWASTE.Make( Proc, Part, OptionalParameters)
    end
    local nToolIndex = OptionalParameters.nToolIndex
    local dExtendAfterTail = OptionalParameters.dExtendAfterTail or 10000
-   local bFinishWithMill
-   if OptionalParameters.bFinishWithMill == nil then
-      bFinishWithMill = true
-   else
-      bFinishWithMill = OptionalParameters.bFinishWithMill
-   end
+   local bFinishWithMill = ( OptionalParameters.bFinishWithMill ~= false)
    local dMillingOffsetFromSide = OptionalParameters.dMillingOffsetFromSide or 1
    local dStripWidth = OptionalParameters.dStripWidth or 5
    local bForced = OptionalParameters.bForced or false
@@ -173,28 +255,26 @@ function BLADEKEEPWASTE.Make( Proc, Part, OptionalParameters)
    -- volume della feature
    local dFeatureVolume = Proc.dVolume
 
-   -- si trovano le facce da lavorare
-   local BottomFace = {}
-   local LongFaces = {}
+   -- si trovano le facce da lavorare (solo 4 lati esatti)
+   local BottomFace1
+   local BottomFace2
    if Proc.nFct == 1 then
-      BottomFace = Proc.Faces[1]
+      BottomFace1 = Proc.Faces[1]
    else
       if not Proc.MainFaces then
          Proc.MainFaces = FaceData.GetMainFaces( Proc, Part)
       end
-      BottomFace = Proc.MainFaces.BottomFaces[1]
-      LongFaces = Proc.MainFaces.LongFaces
+      BottomFace1 = Proc.MainFaces.BottomFaces[1]
+      BottomFace2 = Proc.MainFaces.BottomFaces[2]
    end
-   
-
-   -- si trova il lato della faccia di fondo da lavorare
-   local BottomEdgeToMachine = {}
-   local BottomEdgesSorted = {}
-   for i = 1, #BottomFace.Edges do
-      table.insert( BottomEdgesSorted, BottomFace.Edges[i])
+   if #BottomFace1.Edges ~= 4 then
+      Result = FeatureLib.GetStrategyResultNotApplicable()
+      return Machinings, Result
+   end
+   local bConvexAngle
+   if BottomFace2 then
+      bConvexAngle = ( Proc.AdjacencyMatrix[BottomFace1.id + 1][BottomFace2.id + 1]) > 0
    end
-   table.sort( BottomEdgesSorted, CompareEdges)
-   BottomEdgeToMachine = BottomEdgesSorted[1]
 
    -- eventuali punti di spezzatura
    local FeatureSplittingPoints = FeatureLib.GetFeatureSplittingPoints( Proc, Part)
@@ -203,92 +283,126 @@ function BLADEKEEPWASTE.Make( Proc, Part, OptionalParameters)
       bIsSplitFeature = true
    end
 
-   -- calcolo lavorazioni
-   -- taglio eventuali facce di chiusura o seconda faccia
-      for i = 1, #LongFaces do
-         local Cutting = {}
-         local OptionalParametersFaceByBlade = { bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail, nToolIndex = nToolIndex}
-         Cutting = FaceByBlade.Make( Proc, Part, LongFaces[i], LongFaces[i].MainEdges.BottomEdge, OptionalParametersFaceByBlade)
-         Cutting.nInternalSortingPriority = 1
-         Cutting.dResultWeight = 0.15
-         table.insert( CalculatedMachinings, Cutting)
-      end
-
-   -- taglio con codolo faccia di fondo; si provano solo i lati a cui si può accedere (lato opposto aperto)
-   -- TODO il check del lato opposto aperto andrà messo nella FaceByBlade
-   -- TODO verificare se il calcolo del completamento (aggiunta lavorazioni applicabili/non) é corretto
-   local dDepthToMachine = BottomEdgeToMachine.dElevation / 2 - dStripWidth / 2
-   local OptionalParametersFaceByBlade1 = { dDepthToMachine = dDepthToMachine, bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail, nToolIndex = nToolIndex}
-   local BottomEdgeToMachineOpposite = BeamLib.FindEdgeBestOrientedAsDirection( BottomFace.Edges, -BottomEdgeToMachine.vtN)
-   -- primo lato
-   if BottomEdgeToMachineOpposite.bIsOpen then
-      Cutting1 = FaceByBlade.Make( Proc, Part, BottomFace, BottomEdgeToMachine, OptionalParametersFaceByBlade1)
+   -- calcolo lavorazioni faccia principale
+   -- ricerca lato da lavorare
+   local BottomEdgeToMachine1 = GetLongEdgeToMachine( BottomFace1, { bTop = true})
+   if not BottomEdgeToMachine1 then
+      Result = FeatureLib.GetStrategyResultNotApplicable()
+      return Machinings, Result
    end
-   Cutting1.nInternalSortingPriority = 3
-   Cutting1.dResultWeight = 0.3
-
-   -- secondo lato
-   local OptionalParametersFaceByBlade2 = BeamLib.TableCopyDeep( OptionalParametersFaceByBlade1)
-   OptionalParametersFaceByBlade2.OppositeToolDirectionMode = 'Enabled'
-   if BottomEdgeToMachine.bIsOpen then
-      Cutting2 = FaceByBlade.Make( Proc, Part, BottomFace, BottomEdgeToMachine, OptionalParametersFaceByBlade2)
+   -- calcolo lavorazione
+   local Parameters1 = {
+      bIsSplitFeature = bIsSplitFeature,
+      dExtendAfterTail = dExtendAfterTail,
+      nToolIndex = nToolIndex,
+      dStripWidth = dStripWidth,
+      OtherBottomFace = BottomFace2
+   }
+   local Cuttings1 = MakeBottomFace( Proc, Part, BottomFace1, BottomEdgeToMachine1, Parameters1)
+   -- aggiunta lavorazioni alla lista principale
+   for i = 1, #Cuttings1 do
+      table.insert( CalculatedMachinings, Cuttings1[i])
    end
-   Cutting2.nInternalSortingPriority = 3
-   Cutting2.dResultWeight = 0.3
 
-   -- se uno dei due lati non è riuscito, si estende il più possibile il lato rimasto
-   if not Cutting1.bIsApplicable and Cutting2.bIsApplicable then
-
-      -- se si lavora il lato in comune con la LongFace significa che la LongFace non é di chiusura ma un'altra faccia vera e propria
-      -- ci si deve quindi fermare piú indietro
-      for i = 1, #LongFaces do
-         if BottomEdgeToMachine.idAdjacentFace == LongFaces[i].id then
-            dStripWidth = TOOLS[Cutting2.nToolIndex].dThickness + 2 * dStripWidth
-            break
+   -- calcolo lavorazioni faccia secondaria, solo se lato convesso; se concavo, sarà lavorato come antisplint
+   local Cuttings2
+   local BottomEdgeToMachine2
+   if BottomFace2 then
+      if bConvexAngle then
+         -- ricerca lato da lavorare
+         BottomEdgeToMachine2 = GetLongEdgeToMachine( BottomFace2, { bTop = true})
+         if BottomEdgeToMachine2 then
+            -- calcolo lavorazione
+            local Parameters2 = BeamLib.TableCopyDeep( Parameters1)
+            Parameters2.OtherBottomFace = BottomFace1
+            Cuttings2 = MakeBottomFace( Proc, Part, BottomFace2, BottomEdgeToMachine2, Parameters2)
+            for i = 1, #Cuttings2 do
+               table.insert( CalculatedMachinings, Cuttings2[i])
+            end
          end
       end
-      dDepthToMachine = min( TOOLS[Cutting2.nToolIndex].dMaxMaterial, BottomEdgeToMachine.dElevation - dStripWidth)
-      OptionalParametersFaceByBlade2.dDepthToMachine = dDepthToMachine
-
-      Cutting2 = FaceByBlade.Make( Proc, Part, BottomFace, BottomEdgeToMachine, OptionalParametersFaceByBlade2)
-      Cutting2.nInternalSortingPriority = 3
-      Cutting2.dResultWeight = 0.3
-      table.insert( CalculatedMachinings, Cutting2)
-
-   elseif not Cutting2.bIsApplicable and Cutting1.bIsApplicable then
-
-      -- se si lavora il lato in comune con la LongFace significa che la LongFace non é di chiusura ma un'altra faccia vera e propria
-      -- ci si deve quindi fermare piú indietro
-      for i = 1, #LongFaces do
-         if BottomEdgeToMachine.idAdjacentFace == LongFaces[i].id then
-            dStripWidth = TOOLS[Cutting1.nToolIndex].dThickness + 2 * dStripWidth
-            break
-         end
-      end
-      dDepthToMachine = min( TOOLS[Cutting1.nToolIndex].dMaxMaterial, BottomEdgeToMachine.dElevation - dStripWidth)
-      OptionalParametersFaceByBlade1.dDepthToMachine = dDepthToMachine
-
-      Cutting1 = FaceByBlade.Make( Proc, Part, BottomFace, BottomEdgeToMachine, OptionalParametersFaceByBlade1)
-      Cutting1.nInternalSortingPriority = 3
-      Cutting1.dResultWeight = 0.3
-      table.insert( CalculatedMachinings, Cutting1)
-
-   else
-      table.insert( CalculatedMachinings, Cutting1)
-      table.insert( CalculatedMachinings, Cutting2)
    end
 
-   -- fresatura eventuali facce di chiusura
+   -- antischeggia sulle facce di chiusura delle facce lavorate
+   local OptionalParametersAntiSplint = {
+      bIsSplitFeature = bIsSplitFeature,
+      dExtendAfterTail = dExtendAfterTail,
+      nInternalSortingPriority = 1,
+      dResultWeight = 0.15,
+      bMachineAllClosedEdges = true
+   }
+   local AntiSplints1 = AntiSplintOnFace.Make( Proc, Part, BottomFace1, OptionalParametersAntiSplint)
+   for i = 1, #AntiSplints1 do
+      table.insert( CalculatedMachinings, AntiSplints1[i])
+   end
+   if BottomFace2 and bConvexAngle then
+      OptionalParametersAntiSplint.bMachineAllClosedEdges = false
+      local AntiSplints2 = AntiSplintOnFace.Make( Proc, Part, BottomFace2, OptionalParametersAntiSplint)
+      for i = 1, #AntiSplints2 do
+         table.insert( CalculatedMachinings, AntiSplints2[i])
+      end
+   end
+
+   -- pulitura con fresa dei lati chiusi non lavorati
+   -- TODO funzione
    if bFinishWithMill then
-      for i = 1, #LongFaces do
-         if BottomEdgeToMachine.idAdjacentFace ~= LongFaces[i].id then
-            local dDepthToMachineMill = BottomFace.MainEdges.LongEdges[i].dElevation - dMillingOffsetFromSide
-            local dToolMarkLength = max( Cutting1.dToolMarkLength or 0, Cutting2.dToolMarkLength or 0)
-            local OptionalParametersFaceByMill = { bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail,
-                                                   dRadialStepSpan = dToolMarkLength, dDepthToMachine = dDepthToMachineMill
-                                                }
-            local Milling = FaceByMill.Make( Proc, Part, BottomFace, BottomFace.MainEdges.LongEdges[i], OptionalParametersFaceByMill)
-            Milling.nInternalSortingPriority = 2
+
+      if Cuttings1 then
+         -- si recuperano i lati chiusi non lavorati
+         local EdgesClosedNotMachined = {}
+         for i = 1, #BottomFace1.Edges do
+            if not( ( BottomFace1.Edges[i].id == BottomEdgeToMachine1.id) or BottomFace1.Edges[i].bIsOpen) then
+               table.insert( EdgesClosedNotMachined, BottomFace1.Edges[i])
+            end
+         end
+         -- su ognuno si fa la fresatura di pulizia
+         for i = 1, #EdgesClosedNotMachined do
+            local dDepthToMachine = EdgesClosedNotMachined[i].dElevation - dMillingOffsetFromSide
+            local dToolMarkLength = 0
+            -- si prende l'impronta dell'utensile più grande
+            for j = 1, #Cuttings1 do
+               if Cuttings1[j].dToolMarkLength > dToolMarkLength + 10 * GEO.EPS_SMALL then
+                  dToolMarkLength = Cuttings1[j].dToolMarkLength
+               end
+            end
+            local OptionalParametersMilling = {
+               bIsSplitFeature = bIsSplitFeature,
+               dExtendAfterTail = dExtendAfterTail,
+               dRadialStepSpan = dToolMarkLength,
+               dDepthToMachine = dDepthToMachine
+            }
+            local Milling = FaceByMill.Make( Proc, Part, BottomFace1, EdgesClosedNotMachined[i], OptionalParametersMilling)
+            Milling.nInternalSortingPriority = 3
+            Milling.dResultWeight = 0.05
+            table.insert( CalculatedMachinings, Milling)
+         end
+      end
+      if Cuttings2 and BottomEdgeToMachine2 then
+         -- si recuperano i lati chiusi non lavorati
+         local EdgesClosedNotMachined = {}
+         for i = 1, #BottomFace2.Edges do
+            if not( ( BottomFace2.Edges[i].id == BottomEdgeToMachine2.id) or BottomFace2.Edges[i].bIsOpen) then
+               table.insert( EdgesClosedNotMachined, BottomFace2.Edges[i])
+            end
+         end
+         -- su ognuno si fa la fresatura di pulizia
+         for i = 1, #EdgesClosedNotMachined do
+            local dDepthToMachine = EdgesClosedNotMachined[i].dElevation - dMillingOffsetFromSide
+            local dToolMarkLength = 0
+            -- si prende l'impronta dell'utensile più grande
+            for j = 1, #Cuttings2 do
+               if Cuttings2[j].dToolMarkLength > dToolMarkLength + 10 * GEO.EPS_SMALL then
+                  dToolMarkLength = Cuttings2[j].dToolMarkLength
+               end
+            end
+            local OptionalParametersMilling = {
+               bIsSplitFeature = bIsSplitFeature,
+               dExtendAfterTail = dExtendAfterTail,
+               dRadialStepSpan = dToolMarkLength,
+               dDepthToMachine = dDepthToMachine
+            }
+            local Milling = FaceByMill.Make( Proc, Part, BottomFace2, EdgesClosedNotMachined[i], OptionalParametersMilling)
+            Milling.nInternalSortingPriority = 3
             Milling.dResultWeight = 0.05
             table.insert( CalculatedMachinings, Milling)
          end
@@ -317,7 +431,9 @@ function BLADEKEEPWASTE.Make( Proc, Part, OptionalParameters)
    table.sort( Machinings, SortMachiningsBySegment)
 
    -- calcolo risultati
-   if Cutting1.bIsApplicable or Cutting2.bIsApplicable then
+   if ( Cuttings1 and ( ( Cuttings1[1] and Cuttings1[1].bIsApplicable) or ( Cuttings1[2] and Cuttings1[2].bIsApplicable)))
+      or ( Cuttings2 and ( ( Cuttings2[1] and Cuttings2[1].bIsApplicable) or ( Cuttings2[2] and Cuttings2[2].bIsApplicable))) then
+
       Result.dQuality = FeatureLib.GetStrategyQuality( Machinings)
       Result.dTimeToMachine = FeatureLib.GetStrategyTimeToMachine( Machinings)
       Result.dMRR = ( dFeatureVolume / Result.dTimeToMachine) / pow( 10, 6)

StrategyLibs/BLADETOWASTE.lua

@@ -260,7 +260,7 @@ local function GetBestBlade( Proc, Part, Face, OptionalParameters)
    local dShortPartLength = OptionalParameters.dShortPartLength or BeamData.LEN_SHORT_PART
    local EdgeToMachineTop = OptionalParameters.EdgeToMachineTop
    local EdgeToMachineBottom = OptionalParameters.EdgeToMachineBottom
-   local bIsDicing = OptionalParameters.bIsDicing
+   local idCheckCollisionTm = OptionalParameters.idCheckCollisionTm
    local sRestLengthSideForPreSimulation = OptionalParameters.sRestLengthSideForPreSimulation
    local bCannotSplitRestLength = OptionalParameters.bCannotSplitRestLength
    -- TODO qui sarebbe meglio avere dExtra come OptionalParameter???
@@ -289,7 +289,7 @@ local function GetBestBlade( Proc, Part, Face, OptionalParameters)
          FaceToMachine = Face,
          EdgeToMachine = EdgeToMachineTop,
          Part = Part,
-         bIsDicing = bIsDicing,
+         idCheckCollisionTm = idCheckCollisionTm,
          sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
          bCannotSplitRestLength = bCannotSplitRestLength
       })
@@ -304,7 +304,7 @@ local function GetBestBlade( Proc, Part, Face, OptionalParameters)
          FaceToMachine = Face,
          EdgeToMachine = EdgeToMachineBottom,
          Part = Part,
-         bIsDicing = bIsDicing,
+         idCheckCollisionTm = idCheckCollisionTm,
          sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
          bCannotSplitRestLength = bCannotSplitRestLength
       })
@@ -371,7 +371,7 @@ local function GetSingleCutStrategy( Proc, Part, OptionalParameters)
    local bReduceBladePath = OptionalParameters.bReduceBladePath or false
    local bAllowFastCuts = OptionalParameters.bAllowFastCuts or false
    local FaceToMachine = Proc.Faces[OptionalParameters.nFaceToMachineIndex or 1]
-   local bIsDicing = OptionalParameters.bIsDicing or false
+   local idCheckCollisionTm = OptionalParameters.idCheckCollisionTm
    local sRestLengthSideForPreSimulation = OptionalParameters.sRestLengthSideForPreSimulation or 'Tail'
    local bCannotSplitRestLength = OptionalParameters.bCannotSplitRestLength or false
    -- lati da lavorare in base al tipo di lama
@@ -390,7 +390,7 @@ local function GetSingleCutStrategy( Proc, Part, OptionalParameters)
       EdgeToMachineTop = EdgeToMachineList.Top,
       EdgeToMachineBottom = EdgeToMachineList.Bottom,
       nToolIndex = nToolIndex,
-      bIsDicing = bIsDicing,
+      idCheckCollisionTm = idCheckCollisionTm,
       sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
       bCannotSplitRestLength = bCannotSplitRestLength
    }
@@ -442,7 +442,7 @@ local function GetSingleCutStrategy( Proc, Part, OptionalParameters)
          FaceToMachine = FaceToMachine,
          EdgeToMachine = EdgeToMachineList.TopGuillotine,
          Part = Part,
-         bIsDicing = bIsDicing,
+         idCheckCollisionTm = idCheckCollisionTm,
          sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
          bCannotSplitRestLength = bCannotSplitRestLength
       })
@@ -475,7 +475,7 @@ local function GetDualSideCutStrategy( Proc, Part, OptionalParameters)
    OptionalParameters = OptionalParameters or {}
    local nToolIndex = OptionalParameters.nToolIndex
    local FaceToMachine = Proc.Faces[OptionalParameters.nFaceToMachineIndex or 1]
-   local bIsDicing = OptionalParameters.bIsDicing or false
+   local idCheckCollisionTm = OptionalParameters.idCheckCollisionTm
    local sRestLengthSideForPreSimulation = OptionalParameters.sRestLengthSideForPreSimulation or 'Tail'
    local bCannotSplitRestLength = OptionalParameters.bCannotSplitRestLength or false
 
@@ -499,7 +499,7 @@ local function GetDualSideCutStrategy( Proc, Part, OptionalParameters)
          FaceToMachine = FaceToMachine,
          EdgeToMachine = EdgeToMachine,
          Part = Part,
-         bIsDicing = bIsDicing,
+         idCheckCollisionTm = idCheckCollisionTm,
          sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
          bCannotSplitRestLength = bCannotSplitRestLength
       })
@@ -512,7 +512,7 @@ local function GetDualSideCutStrategy( Proc, Part, OptionalParameters)
          FaceToMachine = FaceToMachine,
          EdgeToMachine = BeamLib.FindEdgeBestOrientedAsDirection( FaceToMachine.Edges, -EdgeToMachine.vtN),
          Part = Part,
-         bIsDicing = bIsDicing,
+         idCheckCollisionTm = idCheckCollisionTm,
          sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
          bCannotSplitRestLength = bCannotSplitRestLength
       })
@@ -534,7 +534,7 @@ local function GetDualSideCutStrategy( Proc, Part, OptionalParameters)
             FaceToMachine = FaceToMachine,
             EdgeToMachine = BeamLib.FindEdgeBestOrientedAsDirection( FaceToMachine.Edges, -EdgeToMachine.vtN),
             Part = Part,
-            bIsDicing = bIsDicing,
+            idCheckCollisionTm = idCheckCollisionTm,
             sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
             bCannotSplitRestLength = bCannotSplitRestLength
          })
@@ -553,7 +553,7 @@ local function GetDualSideCutStrategy( Proc, Part, OptionalParameters)
             FaceToMachine = FaceToMachine,
             EdgeToMachine = EdgeToMachine,
             Part = Part,
-            bIsDicing = bIsDicing,
+            idCheckCollisionTm = idCheckCollisionTm,
             sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
             bCannotSplitRestLength = bCannotSplitRestLength
          })
@@ -589,7 +589,7 @@ local function GetDualSideCutStrategy( Proc, Part, OptionalParameters)
       FaceToMachine = FaceToMachine,
       EdgeToMachine = EdgeToMachine,
       Part = Part,
-      bIsDicing = bIsDicing,
+      idCheckCollisionTm = idCheckCollisionTm,
       sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
       bCannotSplitRestLength = bCannotSplitRestLength
    })
@@ -607,7 +607,7 @@ local function GetDualSideCutStrategy( Proc, Part, OptionalParameters)
          dDepthToMachine = dDepthToMachine
       }
       local BladeEngagementOptionalParameters = {
-         bIsDicing = bIsDicing,
+         idCheckCollisionTm = idCheckCollisionTm,
          sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
          bCannotSplitRestLength = bCannotSplitRestLength
       }
@@ -782,6 +782,52 @@ local function CutWholeWaste( Proc, Part, OptionalParameters)
 end
 
 
+local function UpdateDiceRaw( idRaw, idParallelTm, idPerpendicularTm, Part, MainFace, OtherFace)
+
+   -- frame solidale alla feature
+   local vtZ = MainFace.vtN
+   local vtX = OtherFace and OtherFace.vtN or nil
+   local frMainFace = Frame3d( MainFace.ptCenter, vtZ, vtX)
+
+   -- box del cubetto in riferimento feature
+   local b3Surf = EgtGetBBoxRef( idParallelTm, GDB_BB.STANDARD, frMainFace)
+   if idPerpendicularTm then
+      local b3SurfPerpendicular = EgtGetBBoxRef( idPerpendicularTm, GDB_BB.STANDARD, frMainFace)
+      b3Surf:Add( b3SurfPerpendicular)
+   else
+      -- se non arriva la superficie perpendicolare è un solo taglio parallelo: si estende il box in Z in modo da uscire dal pezzo
+      local ptDeltaZ = b3Surf:getMax() + vtZ * ( MainFace.dElevation + 5)
+      b3Surf:Add( ptDeltaZ)
+   end
+
+   -- estensione box per non avere problemi nella sottrazione booleana
+   if OtherFace and idPerpendicularTm then
+      local vtY = vtZ ^ vtX
+      local ptDeltaX = b3Surf:getMax() + vtX * 1
+      local ptDeltaZ = b3Surf:getMax() + vtZ * 1
+      local ptDeltaYplus = b3Surf:getMax() + vtY * 1
+      local ptDeltaYminus = b3Surf:getMin() - vtY * 1
+      b3Surf:Add( ptDeltaX)
+      b3Surf:Add( ptDeltaZ)
+      b3Surf:Add( ptDeltaYplus)
+      b3Surf:Add( ptDeltaYminus)
+   else
+      b3Surf:expand( 1)
+   end
+   
+   -- si porta il box in riferimento globale 
+   b3Surf:toGlob( frMainFace)
+
+   -- conversione box cubetto in superficie
+   local idSurfTmToSubtract = EgtSurfTmBBox( Part.idTempGroup, b3Surf, false, GDB_RT.GLOB)
+
+   -- sottrazione del cubetto dal grezzo
+   EgtSurfTmSubtract( idRaw, idSurfTmToSubtract)
+
+   return idRaw
+end
+
+
 local function CalculateDiceMachinings( vCuts, Parameters)
    local Machinings = {}
    local bMoveAfterSplit = false
@@ -789,25 +835,24 @@ local function CalculateDiceMachinings( vCuts, Parameters)
    local Proc = Parameters.Proc
    local Part = Parameters.Part
    local MainFace = Parameters.MainFace
+   local OtherFace = next( Parameters.OtherFace) and Parameters.OtherFace or nil
    local Tool = Parameters.Tool
    local sChosenBladeType = Parameters.sChosenBladeType
    local dExtendAfterTail = Parameters.dExtendAfterTail
    local bReduceBladePath = Parameters.bReduceBladePath
    local sRestLengthSideForPreSimulation = Parameters.sRestLengthSideForPreSimulation
    local bCannotSplitRestLength = Parameters.bCannotSplitRestLength
+   local bReduceDiceDepth = Parameters.bReduceDiceDepth
+
+   -- trimesh con RestLength
+   local b3CheckCollision = BeamLib.GetPartBoxWithHeadTail( Part, sRestLengthSideForPreSimulation)
+   local idCheckCollisionTm = EgtSurfTmBBox( Part.idTempGroup, b3CheckCollision, false, GDB_RT.GLOB)
 
    -- eventuale inversione tagli ortogonali e aggiunta informazioni alla geometria
    local bAreOrthogonalCutsInverted = false
    for i = 1, #vCuts do
       for j = 1, #vCuts[i] do
          SetDiceFaceInfo( Proc, vCuts[i][j])
-         if ( i % 2) == 1 then
-            local vtO = EgtSurfTmFacetNormVersor( vCuts[i][j], 0, GDB_ID.ROOT)
-            if MachiningLib.IsFaceZOutOfRange( vtO, Tool) then
-               EgtInvertSurf( vCuts[i][j])
-               bAreOrthogonalCutsInverted = true
-            end
-         end
       end
    end
    -- calcolo lavorazioni
@@ -848,19 +893,17 @@ local function CalculateDiceMachinings( vCuts, Parameters)
       end
       -- calcolo lavorazione della singola faccia
       -- per tagli paralleli e faccia aperta si prova a tagliare come se fosse una faccia singola, accorpando i tagli
-      -- TODO bIsDicing è da mettere a true?
       local bCanMergeParallelCuts = ( ( i % 2) == 0) and ( Proc.nFct == 1)
       local bIsDicingOk = true
       if bCanMergeParallelCuts then
          local nAddGrpId = BeamLib.GetAddGroup( Part.id)
-         local nSurfToCut = EgtSurfTmBySewing( nAddGrpId, vCuts[i], false)
-         local ProcTrimesh = FeatureLib.GetProcFromTrimesh( nSurfToCut, Part)
+         local idSurfToCut = EgtSurfTmBySewing( nAddGrpId, vCuts[i], false)
+         local ProcTrimesh = FeatureLib.GetProcFromTrimesh( idSurfToCut, Part)
 
          local OptionalParametersCutWholeWaste = {
             nToolIndex = Tool.nIndex,
             dExtendAfterTail = dExtendAfterTail,
             bReduceBladePath = bReduceBladePath,
-            bIsDicing = false,
             sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
             bCannotSplitRestLength = bCannotSplitRestLength
          }
@@ -873,16 +916,25 @@ local function CalculateDiceMachinings( vCuts, Parameters)
                   bMoveAfterSplit = true
                end
             end
+            -- aggiornamento grezzo dinamico
+            if i % 2 == 0 then
+               UpdateDiceRaw( idCheckCollisionTm, idSurfToCut, vCuts[i-1][#vCuts[i-1]], Part, MainFace, OtherFace)
+            end
          else
-            EgtErase( nSurfToCut)
+            EgtErase( idSurfToCut)
             bIsDicingOk = false
          end
       end
       -- caso standard (tagli perpendicolari o paralleli non accorpabili)
       if ( not bCanMergeParallelCuts) or ( not bIsDicingOk) then
          for j = 1, #vCuts[i] do
-            -- in generale sta sollevato di pochissimo
-            local dExtraCut = -0.1
+            -- se abilitato, la lama sta sollevata per non rovinare le facce
+            local dExtraCut
+            if bReduceDiceDepth == false then
+               dExtraCut = 0
+            else
+               dExtraCut = -0.1
+            end
             -- se tagli paralleli
             if ( i % 2) == 0 then
                -- se non ci sono tagli ortogonali devo affondare
@@ -910,8 +962,10 @@ local function CalculateDiceMachinings( vCuts, Parameters)
                dRadialStepSpan = 0,
                dExtendAfterTail = dExtendAfterTail,
                bIsDicing = true,
+               idCheckCollisionTm = idCheckCollisionTm,
                sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
-               bCannotSplitRestLength = bCannotSplitRestLength
+               bCannotSplitRestLength = bCannotSplitRestLength,
+               bDisableRealElevationCheck = true
             }
             Cutting = FaceByBlade.Make( ProcTrimesh, Part, FaceToMachine, EdgeToMachine, OptionalParametersFaceByBlade)
             Cutting.ptCenter = Point3d( ProcTrimesh.Faces[1].ptCenter:getX(), 0, 0)
@@ -926,6 +980,10 @@ local function CalculateDiceMachinings( vCuts, Parameters)
             if Cutting.sStage == 'AfterTail' then
                bMoveAfterSplit = true
             end
+            -- aggiornamento grezzo dinamico
+            if i % 2 == 0 then
+               UpdateDiceRaw( idCheckCollisionTm, vCuts[i][j], vCuts[i-1][j], Part, MainFace, OtherFace)
+            end
          end
       end
    end
@@ -961,10 +1019,13 @@ local function CutWithDicing( Proc, Part, OptionalParameters)
       end
    end
 
+   -- angolo tra le facce, se più di una
+   local dAngleBetweenFaces = Proc.AdjacencyMatrix[1][2] or 0
+
    -- scelta lama da sopra o da sotto
    local sChosenBladeType = ''
    if not nToolIndex then
-      nToolIndex, sChosenBladeType = GetBestBlade( Proc, Part, Face1)
+      nToolIndex, sChosenBladeType = GetBestBlade( Proc, Part)
    end
 
    -- se non trovata lama la lavorazione non è fattibile
@@ -1000,12 +1061,14 @@ local function CutWithDicing( Proc, Part, OptionalParameters)
       Proc = Proc,
       Part = Part,
       MainFace = Face1,
+      OtherFace = Face2,
       Tool = TOOLS[nToolIndex],
       sChosenBladeType = sChosenBladeType,
       dExtendAfterTail = dExtendAfterTail,
       bReduceBladePath = bReduceBladePath,
       sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
-      bCannotSplitRestLength = bCannotSplitRestLength
+      bCannotSplitRestLength = bCannotSplitRestLength,
+      bReduceDiceDepth = ( dAngleBetweenFaces < - 10) -- per facce molto aperte non si riduce l'affondamento della lama nei cubetti (rischio che non si stacchino)
    }
 
    bIsDicingOk, Machinings, bMoveAfterSplit = CalculateDiceMachinings( vCuts, Parameters)
@@ -1215,14 +1278,21 @@ function BLADETOWASTE.Make( ProcOrId, Part, OptionalParameters)
       else
          -- per ogni faccia si calcola la lavorazione
          for i = 1, #Proc.Faces do
-            -- ricerca lato in comune da lavorare
+            -- ricerca lato in comune da lavorare; se non trovato è una feature splittata (DoubleBevel) e il lato sarà scelto della GetSingleCutStratetegy
             local nCommonEdgeIndex
             for j = 1, #Proc.Faces[i].Edges do
                if Proc.Faces[i].Edges[j].idAdjacentFace > -1 then
                   nCommonEdgeIndex = j
                end
             end
-            local EdgeToMachine = Proc.Faces[i].Edges[nCommonEdgeIndex]
+            local EdgeToMachine
+            if nCommonEdgeIndex then
+               EdgeToMachine = Proc.Faces[i].Edges[nCommonEdgeIndex]
+            end
+            local EdgeToMachineList
+            if EdgeToMachine then
+               EdgeToMachineList = { Top = EdgeToMachine, Bottom = EdgeToMachine}
+            end
 
             -- scelta lama
             local nToolIndex = OptionalParameters.nToolIndex
@@ -1230,11 +1300,11 @@ function BLADETOWASTE.Make( ProcOrId, Part, OptionalParameters)
                local OptionalParametersGetSingleCutStrategy = {
                   bReduceBladePath = false,
                   nFaceToMachineIndex = i,
-                  EdgeToMachineList = { Top = EdgeToMachine, Bottom = EdgeToMachine},
+                  EdgeToMachineList = EdgeToMachineList,
                   sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
                   bCannotSplitRestLength = bCannotSplitRestLength
                }
-               nToolIndex = GetSingleCutStrategy( Proc, Part, OptionalParametersGetSingleCutStrategy)
+               nToolIndex, EdgeToMachine = GetSingleCutStrategy( Proc, Part, OptionalParametersGetSingleCutStrategy)
             end
 
             -- se lama non trovata si provano i cubetti

StrategyLibs/FACEBYBLADE.lua

@@ -72,6 +72,12 @@ local function GetLeadInOut( Machining, EdgeToMachine, bIsSplitFeature)
       LeadOut.dTotalLength = sqrt( LeadOut.dPerpDistance ^ 2 + LeadOut.dTangentDistance ^ 2)
    end
 
+   -- se accorciamenti maggiori della lunghezza lato, la lavorazione non è fattibile
+   if LeadIn.dStartAddLength + LeadOut.dEndAddLength + EdgeToMachine.dLength < 1 then
+
+      return
+   end
+
    -- se lavorazione con OppositeToolDirection o ridotta l'attacco va corretto
    if not AreSameVectorApprox( Machining.vtToolDirection, EdgeToMachine.vtN) then
       LeadIn.dPerpDistance = BeamData.CUT_SIC - Machining.dRadialOffset
@@ -203,8 +209,10 @@ function FACEBYBLADE.Make( Proc, Part, FaceToMachine, EdgeToMachine, OptionalPar
    local dRadialStepSpan = OptionalParameters.dRadialStepSpan
    local sUserNotes = OptionalParameters.sUserNotes or ''
    local bIsDicing = OptionalParameters.bIsDicing or false
+   local idCheckCollisionTm = OptionalParameters.idCheckCollisionTm
    local sRestLengthSideForPreSimulation = OptionalParameters.sRestLengthSideForPreSimulation or 'Tail'
    local bCannotSplitRestLength = OptionalParameters.bCannotSplitRestLength or false
+   local bDisableRealElevationCheck = OptionalParameters.bDisableRealElevationCheck or false
 
    -- lunghezze, direzioni e punti caratteristici della lavorazione e del lato lavorato
    Cutting.dEdgeLength = EdgeToMachine.dLength
@@ -225,10 +233,15 @@ function FACEBYBLADE.Make( Proc, Part, FaceToMachine, EdgeToMachine, OptionalPar
          Tool = TOOLS[Cutting.nToolIndex],
          dDepthToMachine = dDepthToMachine
       }
+      if OppositeToolDirectionMode == 'Enabled' then
+         BladeEngagementParameters.Edge = EdgeToMachineOpposite
+      end
       local BladeEngagementOptionalParameters = {
          bIsDicing = bIsDicing,
+         idCheckCollisionTm = idCheckCollisionTm,
          sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
-         bCannotSplitRestLength = bCannotSplitRestLength
+         bCannotSplitRestLength = bCannotSplitRestLength,
+         bDisableRealElevationCheck = bDisableRealElevationCheck
       }
       local Engagement
       TIMER:startElapsed( 'GetBladeEngagement')
@@ -252,6 +265,7 @@ function FACEBYBLADE.Make( Proc, Part, FaceToMachine, EdgeToMachine, OptionalPar
       ToolSearchParameters.Part = Part
       ToolSearchParameters.sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation
       ToolSearchParameters.bCannotSplitRestLength = bCannotSplitRestLength
+      ToolSearchParameters.bDisableRealElevationCheck = bDisableRealElevationCheck
 
       local ToolInfo = MachiningLib.FindBlade( Proc, ToolSearchParameters)
       Cutting.nToolIndex = ToolInfo.nToolIndex
@@ -285,16 +299,18 @@ function FACEBYBLADE.Make( Proc, Part, FaceToMachine, EdgeToMachine, OptionalPar
 
       return Cutting, EdgeToMachine.dElevation
    end
+   
+   -- TODO vedere se la rimozione di questo crea problemi
    -- se tasca chiusa da entrambi i lati e più stretta della lama la lavorazione non è applicabile
-   if not ( EdgeToMachine.bIsStartOpen or EdgeToMachine.bIsEndOpen) then
-      if TOOLS[Cutting.nToolIndex].dDiameter > EdgeToMachine.dLength + 10 * GEO.EPS_SMALL then
-         Cutting.sMessage = 'Pocket too narrow for blade diameter'
-         Cutting.bIsApplicable = false
-         EgtOutLog( Cutting.sMessage)
+   -- if not ( EdgeToMachine.bIsStartOpen or EdgeToMachine.bIsEndOpen) then
+   --    if TOOLS[Cutting.nToolIndex].dDiameter > EdgeToMachine.dLength + 10 * GEO.EPS_SMALL then
+   --       Cutting.sMessage = 'Pocket too narrow for blade diameter'
+   --       Cutting.bIsApplicable = false
+   --       EgtOutLog( Cutting.sMessage)
 
-         return Cutting, EdgeToMachine.dElevation
-      end
-   end
+   --       return Cutting, EdgeToMachine.dElevation
+   --    end
+   -- end
 
    -- parametri della lavorazione
 
@@ -320,7 +336,6 @@ function FACEBYBLADE.Make( Proc, Part, FaceToMachine, EdgeToMachine, OptionalPar
       Cutting.bInvert = not Cutting.bInvert
    end
 
-   -- TODO al momento commentato per trovare i casi in cui nei riposizionamenti scende sul pezzo; poi valutare se lasciare o togliere
    -- se dicing, lato di lavoro e inversione per avere taglio sempre verso l'alto
     if bIsDicing
        and ( Cutting.bInvert and Cutting.vtEdgeDirection:getZ() > 100 * GEO.EPS_SMALL)
@@ -347,8 +362,10 @@ function FACEBYBLADE.Make( Proc, Part, FaceToMachine, EdgeToMachine, OptionalPar
       }
       local BladeEngagementOptionalParameters = {
          bIsDicing = bIsDicing,
+         idCheckCollisionTm = idCheckCollisionTm,
          sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
-         bCannotSplitRestLength = bCannotSplitRestLength
+         bCannotSplitRestLength = bCannotSplitRestLength,
+         bDisableRealElevationCheck = bDisableRealElevationCheck
       }
       TIMER:startElapsed( 'GetBladeEngagement')
       local bIsApplicableOpposite, EngagementOpposite = MachiningLib.GetBladeEngagement( BladeEngagementParameters, BladeEngagementOptionalParameters)
@@ -464,8 +481,10 @@ function FACEBYBLADE.Make( Proc, Part, FaceToMachine, EdgeToMachine, OptionalPar
          }
          local BladeEngagementOptionalParameters = {
             bIsDicing = bIsDicing,
+            idCheckCollisionTm = idCheckCollisionTm,
             sRestLengthSideForPreSimulation = sRestLengthSideForPreSimulation,
-            bCannotSplitRestLength = bCannotSplitRestLength
+            bCannotSplitRestLength = bCannotSplitRestLength,
+            bDisableRealElevationCheck = bDisableRealElevationCheck
          }
          TIMER:startElapsed( 'GetBladeEngagement')
          local bIsApplicable, CurrentEngagement = MachiningLib.GetBladeEngagement( BladeEngagementParameters, BladeEngagementOptionalParameters )

StrategyLibs/FACEBYCHAINSAW.lua

@@ -6,6 +6,7 @@
 local BeamLib = require( 'BeamLib')
 local BeamData = require( 'BeamDataNew')
 local MachiningLib = require( 'MachiningLib')
+local PreSimulationLib = require( 'PreSimulationLib')
 
 -- Tabella per definizione modulo
 local FACEBYCHAINSAW = {}
@@ -42,6 +43,11 @@ local function CalculateLeadInOut( Machining, EdgeToMachine, sSideToMachine, dLe
       LeadOut.dEndAddLength = BeamData.CUT_EXTRA
    end
 
+   -- punti dell'attacco
+   local dLengthToAdd = EgtIf( Machining.bToolInvert, -Machining.dStartSafetyLength, EdgeToMachine.dElevation - ( Machining.dMaxElev or 0) + Machining.dStartSafetyLength)
+   LeadIn.ptPoint = EdgeToMachine.ptStart - EdgeToMachine.vtEdge * LeadIn.dStartAddLength + EdgeToMachine.vtN * dLengthToAdd
+   LeadOut.ptPoint = EdgeToMachine.ptEnd + EdgeToMachine.vtEdge * LeadOut.dEndAddLength + EdgeToMachine.vtN * dLengthToAdd
+
    return LeadIn, LeadOut
 end
 
@@ -75,12 +81,29 @@ function FACEBYCHAINSAW.Make( Proc, Part, FaceToMachine, EdgeToMachine, Optional
    local sDepth = OptionalParameters.sDepth or 'TH'
    local dLongitudinalStepSpan = OptionalParameters.dLongitudinalStepSpan
 
-   -- lunghezze e punti caratteristici della lavorazione e del lato lavorato
+   -- lunghezze, direzioni e punti caratteristici della lavorazione e del lato lavorato
    Mortising.dEdgeLength = EdgeToMachine.dLength
-   if OppositeToolDirectionMode == 'Enabled' then
-      Mortising.vtToolDirection = -EdgeToMachine.vtN
+   local dCalculatedMaxElev = FaceToMachine.Edges[EdgeToMachine.nPreviousEdgeIndex].dLength
+   if FaceToMachine.Edges[EdgeToMachine.nNextEdgeIndex].dLength > FaceToMachine.Edges[EdgeToMachine.nPreviousEdgeIndex].dLength + 10 * GEO.EPS_SMALL then
+      dCalculatedMaxElev = FaceToMachine.Edges[EdgeToMachine.nNextEdgeIndex].dLength
+   end
+   -- la direzione di lavoro è calcolata in accordo con la direzione calcolata dal Cam5
+   -- fine chiusa
+   if EdgeToMachine.bIsStartOpen and not EdgeToMachine.bIsEndOpen then
+      Mortising.vtToolDirection = FaceToMachine.Edges[EdgeToMachine.nNextEdgeIndex].vtEdge
+   -- inizio chiuso
+   elseif EdgeToMachine.bIsEndOpen and not EdgeToMachine.bIsStartOpen then
+      Mortising.vtToolDirection = -FaceToMachine.Edges[EdgeToMachine.nPreviousEdgeIndex].vtEdge
+   -- entrambi aperti o entrambi chiusi
    else
-      Mortising.vtToolDirection = EdgeToMachine.vtN
+      local vtTemp = ( FaceToMachine.Edges[EdgeToMachine.nNextEdgeIndex].vtEdge - FaceToMachine.Edges[EdgeToMachine.nPreviousEdgeIndex].vtEdge) * 0.5
+      vtTemp:normalize()
+      Mortising.vtToolDirection = vtTemp
+   end
+   if OppositeToolDirectionMode == 'Enabled' then
+      Mortising.vtToolDirection = -Mortising.vtToolDirection
+   else
+      Mortising.vtToolDirection = Mortising.vtToolDirection
    end
    Mortising.vtEdgeDirection = Vector3d( EdgeToMachine.vtEdge)
    Mortising.ptEdge1, Mortising.ptEdge2 = EdgeToMachine.ptStart, EdgeToMachine.ptEnd
@@ -164,11 +187,13 @@ function FACEBYCHAINSAW.Make( Proc, Part, FaceToMachine, EdgeToMachine, Optional
    -- massima elevazione
    if dCustomMaxElev < Mortising.dDepthToMachine - 10 * GEO.EPS_SMALL then
       Mortising.dMaxElev = max( dCustomMaxElev, dCustomMaxElev - Mortising.dLongitudinalOffset)
+   else
+      Mortising.dMaxElev = dCalculatedMaxElev
    end
    -- offset radiale
    Mortising.dRadialOffset = 0
    -- distanza di sicurezza
-   Mortising.dStartSafetyLength = max( EdgeToMachine.dElevation, ( TOOLS[Mortising.nToolIndex].SetupInfo.dZSafeDelta or 60) + EgtMdbGetGeneralParam( MCH_GP.SAFEZ))
+   Mortising.dStartSafetyLength = ( TOOLS[Mortising.nToolIndex].SetupInfo.dZSafeDelta or 0) + EgtMdbGetGeneralParam( MCH_GP.SAFEZ)
    -- overlap
    Mortising.dOverlap = 0
    -- step
@@ -189,16 +214,31 @@ function FACEBYCHAINSAW.Make( Proc, Part, FaceToMachine, EdgeToMachine, Optional
    -- SCC
    Mortising.SCC = MCH_SCC.NONE
    -- asse bloccato e angoli suggeriti
-   local vtRes = FaceToMachine.vtN ^ EdgeToMachine.vtN
-   if abs( vtRes:getZ()) < 10 * GEO.EPS_SMALL then
-      Mortising.sBlockedAxis = BeamLib.GetBlockedAxis( Mortising.nToolIndex, 'perpendicular', Part.b3Raw, FaceToMachine.vtN)
-      Mortising.sSuggestedAngles = BeamLib.GetChainSawInitAngs( FaceToMachine.vtN, EdgeToMachine.vtN, 1)
-   elseif EdgeToMachine.vtN:getZ() < 10 * GEO.EPS_SMALL then
-      Mortising.sBlockedAxis = BeamLib.GetBlockedAxis( Mortising.nToolIndex, 'parallel', Part.b3Raw, FaceToMachine.vtN)
-      Mortising.sSuggestedAngles = BeamLib.GetChainSawInitAngs( FaceToMachine.vtN, EdgeToMachine.vtN, 2)
-   end
+   Mortising.sBlockedAxis = BeamLib.GetBlockedAxis( Mortising.nToolIndex, 'perpendicular', Part.b3Raw, FaceToMachine.vtN)
+   Mortising.sInitialAngles = BeamLib.GetChainSawInitAngs( FaceToMachine.vtN, Mortising.vtToolDirection, 1)
    -- approccio e retrazione
    Mortising.LeadIn, Mortising.LeadOut = CalculateLeadInOut( Mortising, EdgeToMachine, sSideToMachine, dLengthToMachine)
+   -- check finecorsa nei punti di attacco
+   local PointsOnToolTipCenter = {
+      Mortising.LeadIn.ptPoint,
+      Mortising.LeadOut.ptPoint
+   }
+   local vtAux = FaceToMachine.vtN
+   if Mortising.bToolInvert then
+      vtAux = -FaceToMachine.vtN
+   end
+   local bOutOfStroke = PreSimulationLib.CheckOutOfStrokeFromPoints( PointsOnToolTipCenter, Mortising.vtToolDirection, Mortising.nSCC, TOOLS[Mortising.nToolIndex], vtAux, Mortising.sBlockedAxis)
+   -- se finecorsa si prova a bloccare l'altro asse
+   if bOutOfStroke then
+      Mortising.sBlockedAxis = BeamLib.GetBlockedAxis( Mortising.nToolIndex, 'parallel', Part.b3Raw, FaceToMachine.vtN)
+      Mortising.sInitialAngles = BeamLib.GetChainSawInitAngs( FaceToMachine.vtN, Mortising.vtToolDirection, 2)
+      bOutOfStroke = PreSimulationLib.CheckOutOfStrokeFromPoints( PointsOnToolTipCenter, Mortising.vtToolDirection, Mortising.nSCC, TOOLS[Mortising.nToolIndex], vtAux, Mortising.sBlockedAxis)
+      if bOutOfStroke then
+         Mortising.sMessage = 'Out of stroke'
+         Mortising.bIsApplicable = false
+         return Mortising
+      end
+   end
    -- eventuale step verticale
    Mortising.CloneStepsLongitudinal = {}
    if not dLongitudinalStepSpan then
@@ -211,7 +251,7 @@ function FACEBYCHAINSAW.Make( Proc, Part, FaceToMachine, EdgeToMachine, Optional
       Mortising.CloneStepsLongitudinal.dStep = dPocketHeight
    end
    -- lunghezza lavorata
-   -- TODO per il calcolo della dLenghtOnX ripetere il calcolo del FACEBYBLADE con proiezione del lato; serve prolungare con la Add Length secondo la vtEdgeDirection
+   -- TODO per il calcolo della dlengthOnX ripetere il calcolo del FACEBYBLADE con proiezione del lato; serve prolungare con la Add Length secondo la vtEdgeDirection
    -- TODO fare funzione EstimatePathLength o simile
    Mortising.dLengthToMachine = Mortising.dEdgeLength + Mortising.LeadIn.dStartAddLength + Mortising.LeadOut.dEndAddLength
    Mortising.dLengthOnX = abs( dLengthToMachine * EdgeToMachine.vtN:getY())

UpdateLog.txt

@@ -1,4 +1,4 @@
            ==== Beam Update Log ====
 
-Versione 2.6-- (--/--/2024)
-- Primo commit creazione nuovo automatismo BEAM con strategie
+Versione 3.1e1 (29/05/2026)
+- Primo commit nuovo automatismo a strategie

Version.lua

@@ -2,5 +2,5 @@
 -- Gestione della versione di Beam
 
 NAME = 'Beam'
-VERSION = '2.8a1'
-MIN_EXE = '2.7j2'
+VERSION = '3.1e1'
+MIN_EXE = '3.1e1'