Quando si scarica motosega, si raddrizza prima l'asse B e poi si muove il C. Ora sempre e non solo se pezzo alto

Common_FAST.NUM.mlpe

@@ -27,7 +27,9 @@ function OnStart()
    --EMT.LINEINC = 1        -- incremento numerazione linee
    --EMT.Ft = 'F'           -- token per feed
    --EMT.St = 'S'           -- token per speed
-   EMT.FMAXPINZE = 154000 -- feed massima pinze
+   EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+   EMT.MAXACC = MaxAcc or ( EMT.FMAXPINZE / ( 60 * 0.3))  -- accelerazione massima pinze
+   EMT.MINACC = MinAcc or ( EMT.FMAXPINZE / ( 60 * 4))    -- accelerazione minima pinze
 end
 
 ---------------------------------------------------------------------
@@ -183,16 +185,12 @@ function OnDispositionEnd()
       local STrave = EMT.ST
       local HOverM = EMT.HOVM
       -- calcolo dati pinze
-      local MinAccPinze = 0.3
-      local MaxAccPinze = 4
       local KgMtCubo= WoodDensity or 550           -- densità legno in Kg / metro cubo
       local Massa = ( HTrave * STrave * LBarra * KgMtCubo ) / 1000000000
       local FMaxPinze = EMT.FMAXPINZE
       local ForzaAtrito = 700 / 2   -- Serve per regolare P32 (700 valore reale pistone)
       local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAtrito) / 1000)
-      if ( TempoAcc < MinAccPinze) then TempoAcc = MinAccPinze end
-      if ( TempoAcc > MaxAccPinze) then TempoAcc = MaxAccPinze end
-      local AccPinze = FMaxPinze / ( 60 * TempoAcc)
+      local AccPinze = EgtClamp( FMaxPinze / ( 60 * TempoAcc), EMT.MINACC, EMT.MAXACC)
       local RidFeed = 100 / Massa * 100
       if ( RidFeed > 100) then RidFeed = 100 end
       if IdTrave >= 0 then
@@ -252,9 +250,9 @@ function OnDispositionEnd()
          EmtOutput( sOut)
       -- altrimenti recupero rimanenza   
       else
-         EmtOutput( 'G112 EC1'..' Y'..EmtLenToString( LoadT, 3).. ' EY'..EmtLenToString( EMT.YPOS, 3)..' EV'..EmtLenToString( ParkV, 3) ..' EF'..GetFmaxClamp())
+         EmtOutput( 'G112 EC1'..' Y'..EmtLenToString( EMT.TPOS, 3).. ' EY'..EmtLenToString( EMT.YPOS, 3)..' EV'..EmtLenToString( ParkV, 3) ..' EF'..GetFmaxClamp())
          -- aggiorno dati aggancio carrelli alla trave
-         EMT.YDELTA = EMT.YPOS - LoadT
+         EMT.YDELTA = EMT.YPOS - EMT.TPOS
          EMT.VDELTA = nil
       end
       -- eventuale preparazione per rotazione immediata
@@ -498,6 +496,7 @@ function OnMachiningEnd()
    EMT.U_STD = nil
    EMT.PREVTOOL = EMT.TOOL
    EMT.PREVHEAD = EMT.HEAD
+   EMT.PREVET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
 end
 
 ---------------------------------------------------------------------
@@ -628,15 +627,26 @@ function OnRapid()
          end
       end
 
+      local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
+
+      local bGoToHome = false
+      -- se gli assi rotanti cambiano parecchio, con motosega si va in parcheggio 
+      if EMT.PREVHEAD == 'H3' and EMT.HEAD == 'H3' and sET == EMT.PREVET and ( abs( EMT.R2pp - EMT.R2) > 25 or abs( EMT.R1pp - EMT.R1) > 25)  then
+         bGoToHome = true
+      end
+
       -- primo posizionamento
       local MyZHome = EgtGetAxisHomePos( 'Z')
       local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or  EMT.L3 > -1)
       -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
+      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.FLAG2 == 1 then
          local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
                                        ' B' .. EmtLenToString( EMT.R2pp, 3) .. ' C' .. EmtLenToString( EMT.R1pp, 3) .. 
                                        ' EE' .. EgtIf( bZmax, '3', '4') .. EMT.PREVsEL .. EMT.PREVsER .. EMT.PREVsET .. EMT.PREVsES
          EmtOutput( sOutPreMove)
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1pp, 3) .. sEE .. sEL .. sER .. sET .. sES
+         EmtOutput( sOutPreMove)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
       end
@@ -650,15 +660,23 @@ function OnRapid()
       local sEE = ' EE' .. EgtIf( bZmax, '3', '4')
       local sEL = ' EL' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TLEN, ( EMT.TDIST or ChSawLen)), 3)
       local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
-      local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
       local sES = ' ES'..EgtNumToString( EMT.S, 0)
 
       -- se carico motosega, ruoto in zona sicura prima di approcciare la lavorazione
-      if not EMT.LOAD and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and 
-         ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350)) and EMT.FLAG2 == 1 then
+      if not EMT.LOAD and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and
+         ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
          local sEEPreMove = ' EE' .. EgtIf( bZmax, '3', '4')
-         local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
-                                       EmtGetAxis( 'R2') .. EmtGetAxis( 'R1') .. sEE .. sEL .. sER .. sET .. sES
+         local sOutPreMove
+         if EMT.HEAD == 'H3' and bGoToHome then
+            sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1pp, 3) .. sEE .. sEL .. sER .. sET .. sES
+            EmtOutput( sOutPreMove)
+            sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
+            EmtOutput( sOutPreMove)
+         end
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( EMT.R2, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
          EmtOutput( sOutPreMove)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')

Common_FAST.NUM_PLUS.mlpe

@@ -27,7 +27,9 @@ function OnStart()
    --EMT.LINEINC = 1        -- incremento numerazione linee
    --EMT.Ft = 'F'           -- token per feed
    --EMT.St = 'S'           -- token per speed
-   EMT.FMAXPINZE = 154000 -- feed massima pinze
+   EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+   EMT.MAXACC = MaxAcc or ( EMT.FMAXPINZE / ( 60 * 0.3))  -- accelerazione massima pinze
+   EMT.MINACC = MinAcc or ( EMT.FMAXPINZE / ( 60 * 4))    -- accelerazione minima pinze
 end
 
 ---------------------------------------------------------------------
@@ -205,9 +207,9 @@ function OnDispositionEnd()
       local BtlInfoId = EgtGetFirstNameInGroup( GDB_ID.ROOT, 'BtlInfo') or EgtGetCurrMachGroup() or GDB_ID.NULL
       local nLoad90 = EgtGetInfo( BtlInfoId, 'LOAD90', 'i') or 0
       -- calcolo dati pinze
-      local AccPinze, AccMaxPinze, RidFeed, TempoAcc = CalcDinamicaPinze( HTrave, STrave, LBarra)
-      local AccPinz1, AccMaxPinz1, RidFeed1, TempoAcc1 = CalcDinamicaPinze( HTrave, STrave, LBarra - LTrave)
-      local AccPinz2, AccMaxPinz2, RidFeed2, TempoAcc2 = CalcDinamicaPinze( HTrave, STrave, LTrave)
+      local AccPinze, AccMaxPinze, RidFeed, TempoAcc = CalcDinamicaPinze_NUM( HTrave, STrave, LBarra)
+      local AccPinz1, AccMaxPinz1, RidFeed1, TempoAcc1 = CalcDinamicaPinze_NUM( HTrave, STrave, LBarra - LTrave)
+      local AccPinz2, AccMaxPinz2, RidFeed2, TempoAcc2 = CalcDinamicaPinze_NUM( HTrave, STrave, LTrave)
       if IdTrave >= 0 then
          local sOut = '( SN='..IdTrave..' LBarra='..EmtLenToString( LBarra, 3)..' L='..EmtLenToString( LTrave, 3)..
                       ' H='..EmtLenToString( HTrave, 3)..' S='..EmtLenToString( STrave, 3)..' Acc='..EgtNumToString( TempoAcc, 1)..
@@ -271,9 +273,9 @@ function OnDispositionEnd()
          EmtOutput( sOut)
       -- altrimenti recupero rimanenza   
       else
-         EmtOutput( 'G112 EC1'..' Y'..EmtLenToString( LoadT, 3).. ' EY'..EmtLenToString( EMT.YPOS, 3)..' EV'..EmtLenToString( ParkV, 3) ..' EF'..GetFmaxClamp())
+         EmtOutput( 'G112 EC1'..' Y'..EmtLenToString( EMT.TPOS, 3).. ' EY'..EmtLenToString( EMT.YPOS, 3)..' EV'..EmtLenToString( ParkV, 3) ..' EF'..GetFmaxClamp())
          -- aggiorno dati aggancio carrelli alla trave
-         EMT.YDELTA = EMT.YPOS - LoadT
+         EMT.YDELTA = EMT.YPOS - EMT.TPOS
          EMT.VDELTA = nil
       end
       -- eventuale preparazione per rotazione immediata
@@ -542,6 +544,7 @@ function OnMachiningEnd()
    EMT.PREVTOOL = EMT.TOOL
    EMT.PREVHEAD = EMT.HEAD
    EMT.PREVR3 = EMT.R3
+   EMT.PREVET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
 end
 
 ---------------------------------------------------------------------
@@ -673,15 +676,26 @@ function OnRapid()
          end
       end
 
+      local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
+
+      local bGoToHome = false
+      -- se gli assi rotanti cambiano parecchio, con motosega si va in parcheggio 
+      if EMT.PREVHEAD == 'H3' and EMT.HEAD == 'H3' and sET == EMT.PREVET and ( abs( EMT.R2pp - EMT.R2) > 25 or abs( EMT.R1pp - EMT.R1) > 25)  then
+         bGoToHome = true
+      end
+
       -- primo posizionamento
       local MyZHome = EgtGetAxisHomePos( 'Z')
       local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or  EMT.L3 > -1)
       -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
+      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.FLAG2 == 1 then
          local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
                                        ' B' .. EmtLenToString( EMT.R2pp, 3) .. ' C' .. EmtLenToString( EMT.R1pp, 3) .. 
                                        ' EE' .. EgtIf( bZmax, '3', '4') .. EMT.PREVsEL .. EMT.PREVsER .. EMT.PREVsET .. EMT.PREVsES
          EmtOutput( sOutPreMove)
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
+         EmtOutput( sOutPreMove)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
       end
@@ -718,15 +732,23 @@ function OnRapid()
          sER = sER..EmtLenToString( EMT.TDIAM / 2, 3)
       end
 
-      local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
       local sES = ' ES'..EgtNumToString( EMT.S, 0)
 
       -- se carico motosega, ruoto in zona sicura prima di approcciare la lavorazione
       if not EMT.LOAD and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and 
-         ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350)) and EMT.FLAG2 == 1 then
+         ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
          local sEEPreMove = ' EE' .. EgtIf( bZmax, '3', '4')
-         local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
-                                       EmtGetAxis( 'R2') .. EmtGetAxis( 'R1') .. sEE .. sEL .. sER .. sET .. sES
+         local sOutPreMove
+         if EMT.HEAD == 'H3' and bGoToHome then
+            sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1pp, 3) .. sEE .. sEL .. sER .. sET .. sES
+            EmtOutput( sOutPreMove)
+            sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
+            EmtOutput( sOutPreMove)
+         end
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( EMT.R2, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
          EmtOutput( sOutPreMove)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
@@ -1094,28 +1116,6 @@ function FindNextTool()
    return sTool, sHead, sTcPos
 end
 
----------------------------------------------------------------------
-function CalcDinamicaPinze( dH, dS, dL)
-   local MinTempoAcc = 0.3                         -- [s]
-   local MaxTempoAcc = 4.0                         -- [s]
-   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
-   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
-   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
-   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
-   local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito) / 1000)
-   if ( TempoAcc < MinTempoAcc) then TempoAcc = MinTempoAcc end
-   if ( TempoAcc > MaxTempoAcc) then TempoAcc = MaxTempoAcc end
-   local AccMaxPinze = FMaxPinze / ( 60 * MinTempoAcc)
-   local AccPinze = FMaxPinze / ( 60 * TempoAcc)
-   local RidFeed = 100 / Massa * 100
-   if RidFeed > 100 then
-      RidFeed = 100
-   elseif RidFeed < 10 then
-      RidFeed = 10
-   end
-   return AccPinze, AccMaxPinze, RidFeed, TempoAcc
-end
-
 ---------------------------------------------------------------------
 function CalcCharStatus( sCmd, bSkipPress)
    -- aperto

Common_FAST.TPA.mlpe

@@ -31,7 +31,9 @@ function OnStart()
    --EMT.LINEINC = 1      -- incremento numerazione linee
    --EMT.Ft = 'F'         -- token per feed
    --EMT.St = 'S'         -- token per speed
-   EMT.FMAXPINZE = 154000 -- feed massima pinze
+   EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+   EMT.MAXACC = MaxAcc or 4000    -- accelerazione massima pinze. In realtà è il tempo in millisecondi, quindi MAXACC corrisponde al tempo massimo per raggiungere la velocità desiderata
+   EMT.MINACC = MinAcc or 300     -- accelerazione minima pinze. In realtà è il tempo in millisecondi, quindi MINACC corrisponde al tempo massimo per raggiungere la velocità desiderata
 end
 
 ---------------------------------------------------------------------
@@ -223,9 +225,9 @@ function OnDispositionEnd()
       local HOverM = EMT.HOVM
 
       -- calcolo dati pinze
-      local TempAccPinze, TempMinAccPinze, RidFeed = CalcDinamicaPinze( HTrave, STrave, LBarra)
-      local TempAccPinz1, TempMinAccPinz1, RidFeed1 = CalcDinamicaPinze( HTrave, STrave, LBarra - LTrave)
-      local TempAccPinz2, TempMinAccPinz2, RidFeed2 = CalcDinamicaPinze( HTrave, STrave, LTrave)
+      local TempAccPinze, TempMinAccPinze, RidFeed = CalcDinamicaPinze_TPA( HTrave, STrave, LBarra)
+      local TempAccPinz1, TempMinAccPinz1, RidFeed1 = CalcDinamicaPinze_TPA( HTrave, STrave, LBarra - LTrave)
+      local TempAccPinz2, TempMinAccPinz2, RidFeed2 = CalcDinamicaPinze_TPA( HTrave, STrave, LTrave)
 
       if IdTrave >= 0 then
          local sPrt = '( *** Part '.. EgtNumToString( IdTrave, 0) ..' ***)'
@@ -273,9 +275,9 @@ function OnDispositionEnd()
                 ' P4=' .. EmtLenToString( HOverM, 2) .. ' P5=' .. tostring( nLoad90) .. ' P6=' .. EmtLenToString( EgtIf( IdTrave >= 0, LTrave, LBarra), 2) ..
                 ' P7=' .. EgtNumToString( TempAccPinze, 2) .. ' P8=' .. EgtNumToString( TempAccPinz2, 2) .. ' P9=' .. EgtNumToString( TempAccPinz1, 2)
          EmtOutput( sOut)
-         EmtOutput( 'M112'..' P1='..EmtLenToString( LoadT, 3).. ' P5=1 P6='..EmtLenToString( EMT.YPOS, 3)..' P7='..EmtLenToString( ParkV, 3) ..' P9='..GetFmaxClamp())
+         EmtOutput( 'M112'..' P1='..EmtLenToString( EMT.TPOS, 3).. ' P5=1 P6='..EmtLenToString( EMT.YPOS, 3)..' P7='..EmtLenToString( ParkV, 3) ..' P9='..GetFmaxClamp())
          -- aggiorno dati aggancio carrelli alla trave
-         EMT.YDELTA = EMT.YPOS - LoadT
+         EMT.YDELTA = EMT.YPOS - EMT.TPOS
          EMT.VDELTA = nil
       end
       -- eventuale preparazione per rotazione immediata
@@ -656,16 +658,28 @@ function OnRapid()
             bHeadFirst = false
          end
       end
+
+      local bGoToHome = false
+      -- se gli assi rotanti cambiano parecchio, con motosega si va in parcheggio 
+      if EMT.PREVHEAD == 'H3' and EMT.HEAD == 'H3' and EMT.TCPOS == EMT.PREVTCPOS and ( abs( EMT.R2pp - EMT.R2) > 25 or abs( EMT.R1pp - EMT.R1) > 25)  then
+         bGoToHome = true
+      end
+   
       -- primo posizionamento
       local MyZHome = EgtGetAxisHomePos( 'Z')
       local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or EMT.L3 > -1)
       -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
+      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.FLAG2 == 1 then
          local sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
                                  ' P4=' .. EgtNumToString( EMT.R2pp, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1pp, EMT.DECMACRO) .. 
                                  ' P6=' .. EgtNumToString( EMT.PREVTCPOS, EMT.DECMACRO) .. ' P7=' .. EgtNumToString( EMT.PREVS, 0) ..
                                  ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
          EmtOutput( sOutPreMove)
+         sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+                                 ' P4=' .. EgtNumToString( 0, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1pp, EMT.DECMACRO) .. 
+                                 ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
+                                 ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
+         EmtOutput( sOutPreMove)
          EmtOutput( 'M101 P1=2')
          EmtOutput( 'M101 P1=3')
       end
@@ -677,8 +691,21 @@ function OnRapid()
 
       -- se carico motosega, ruoto in zona sicura prima di approcciare la lavorazione
       if not EMT.LOAD and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and 
-         ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350)) and EMT.FLAG2 == 1 then
-         local sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+         ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
+         local sOutPreMove
+         if EMT.HEAD == 'H3' and bGoToHome then
+            sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+                                 ' P4=' .. EgtNumToString( 0, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1pp, EMT.DECMACRO) .. 
+                                 ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
+                                 ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
+            EmtOutput( sOutPreMove)
+            sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+                                 ' P4=' .. EgtNumToString( 0, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1, EMT.DECMACRO) .. 
+                                 ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
+                                 ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
+            EmtOutput( sOutPreMove)
+         end
+         sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
                                  ' P4=' .. EgtNumToString( EMT.R2, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1, EMT.DECMACRO) .. 
                                  ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
                                  ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
@@ -1054,28 +1081,6 @@ function FindNextTool()
    return sTool, sHead, sTcPos
 end
 
----------------------------------------------------------------------
-function CalcDinamicaPinze( dH, dS, dL)
-   local MinTempoAcc = 0.3                         -- [s]
-   local MaxTempoAcc = 4.0                         -- [s]
-   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
-   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
-   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
-   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
-   local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito) / 1000)
-   if ( TempoAcc < MinTempoAcc) then TempoAcc = MinTempoAcc end
-   if ( TempoAcc > MaxTempoAcc) then TempoAcc = MaxTempoAcc end
-   local AccMaxPinze = FMaxPinze / ( 60 * MinTempoAcc)
-   local AccPinze = FMaxPinze / ( 60 * TempoAcc)
-   local RidFeed = 100 / Massa * 100
-   if RidFeed > 100 then
-      RidFeed = 100
-   elseif RidFeed < 10 then
-      RidFeed = 10
-   end
-   return TempoAcc * 1000, MinTempoAcc * 1000, RidFeed
-end
-
 ---------------------------------------------------------------------
 function CalcCharStatus( sCmd, bSkipPress)
    -- aperto

Common_FAST.mlpe

@@ -7,9 +7,6 @@ EgtEnableDebug( false)
 -- carico librerie
 local BD = require( 'BeamData')
 
-LONG_TOOL_MINLEN = 221
-BIG_TOOL_DIAM = 300
-
 ---------------------------------------------------------------------
 -- *** GENERATION ***
 ---------------------------------------------------------------------
@@ -168,13 +165,13 @@ function OnSimulDispositionStart()
       -- Determino dimensioni del grezzo
       local nSolId = EgtGetFirstNameInGroup( EgtGetFirstRawPart() or GDB_ID.NULL, 'RawSolid') or GDB_ID.NULL
       local b3Sol = EgtGetBBoxGlob( nSolId, GDB_BB.STANDARD)
-      EMT.LB = 0
-      EMT.SB = 0
-      EMT.HB = 0
+      EMT.LT = 0
+      EMT.ST = 0
+      EMT.HT = 0
       if b3Sol then
-         EMT.LB = b3Sol:getDimX()
-         EMT.SB = b3Sol:getDimY()
-         EMT.HB = b3Sol:getDimZ()
+         EMT.LT = b3Sol:getDimX()
+         EMT.ST = b3Sol:getDimY()
+         EMT.HT = b3Sol:getDimZ()
       end
       -- Carico primo utensile sulla testa 1
       local sTool, nTlen = FindFirstToolOnHead( 'H1')
@@ -558,14 +555,14 @@ function OnSimulToolDeselect()
       -- movimento scarico sega a catena
       if EMT.HEAD == 'H3' then
          -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-         if  EMT.HB > BeamHeightForFixRot then
-            SimulMoveAxis( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID)
-         end
+         SimulMoveAxis( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID)
+         -- raddrizzo asse B prima di ruotare il C
+         SimulMoveAxis( 'B', 0, MCH_SIM_STEP.COLLROT)
          local dPosA = EgtGetAxisPos( 'A')
          if abs( dPosA) < 0.1 then
-            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 180, 0), MCH_SIM_STEP.COLLROT)
+            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, -180, 0), MCH_SIM_STEP.COLLROT)
          else
-            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.COLLROT)
+            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, 270), MCH_SIM_STEP.COLLROT)
          end
          SimulMoveAxis( 'X', 0, MCH_SIM_STEP.RAPID)
       -- movimento scarico rinvio
@@ -608,7 +605,16 @@ function OnSimulToolDeselect()
       if EMT.NEXTHEAD ~= 'H3' and EMT.NEXTHEAD ~= 'H5' and EMT.NEXTHEAD ~= 'H6' then
          SimulMoveAxes( 'B', EgtIf( GetTCSet( EMT.TCPOS) == 1, 90, -90), MCH_SIM_STEP.RAPROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.RAPROT)
       else
-         SimulMoveAxes( 'B', 0, MCH_SIM_STEP.RAPROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.RAPROT)
+         if EMT.NEXTHEAD == 'H3' then
+            local dPosA = EgtGetAxisPos( 'A')
+            if abs( dPosA) < 0.1 then
+               SimulMoveAxes( 'B', 0, MCH_SIM_STEP.RAPROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, 270), MCH_SIM_STEP.RAPROT)
+            else
+               SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, -180, 0), MCH_SIM_STEP.COLLROT)
+            end
+         else
+            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.RAPROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.RAPROT)
+         end
       end
       -- se segue lama, carico utensile di default
       if EMT.NEXTHEAD == 'H2' then
@@ -785,13 +791,25 @@ function OnSimulMoveStart()
    VerifyVStroke( EMT.A2)
    -- se inizio lavorazione
    if EMT.MCHFIRST then
+
+      local bGoToHome = false
+      -- se gli assi rotanti cambiano parecchio, con motosega si va in parcheggio 
+      if EMT.PREVHEAD == 'H3' and EMT.HEAD == 'H3' and EMT.TOOL == EMT.PREVTOOL and abs( EMT.R3p - EMT.R3) < 100 * GEO.EPS_SMALL and ( abs( EMT.R2p - EMT.R2) > 25 or abs( EMT.R1p - EMT.R1) > 25)  then
+         bGoToHome = true
+      end
+
       EgtOutText( '')
       EMT.MCHFIRST = false
       local bZmax = ( EMT.TOOL ~= EMT.PREVTOOL  or EMT.L3 > -1)
       -- con pezzi alti aggiorno gli assi rotanti prima di muovermi sopra il pezzo
-      if not EMT.LOAD and EMT.MOVE == 0 and ( EMT.HB > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TOTLEN > 350)) and EMT.FLAG2 == 1 then
-         -- se motosega mi muovo a X di sicurezza per ruotare
-         if ( EMT.HEAD == 'H3' or ( bZmax and EMT.TOTLEN > 200)) then
+      if not EMT.LOAD and EMT.MOVE == 0 and ( EMT.HEAD == 'H3' or ( EMT.HEAD == 'H1' and EMT.TOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
+         -- se motosega mi muovo a X di sicurezza per ruotare, prima si raddrizza B e poi C in posizione
+         if EMT.HEAD == 'H3' or bGoToHome then
+            SimulMoveAxis( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID)
+            SimulMoveAxis( 'B', 0, MCH_SIM_STEP.COLLROT)
+            SimulMoveAxis( 'C', EMT.R1, MCH_SIM_STEP.COLLROT)
+            SimulMoveAxis( 'B', EMT.R2, MCH_SIM_STEP.COLLROT)
+         elseif ( bZmax and EMT.TOTLEN > 200) then
             SimulMoveAxes( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID, 'C', EMT.R1, MCH_SIM_STEP.COLLROT, 'B', EMT.R2, MCH_SIM_STEP.COLLROT)
          end
       end
@@ -916,14 +934,14 @@ function ExecAuxCmd( sCmd)
    elseif Cmd[1] == '11' then
       local dPY = MaxOpen
       if Cmd[2] ~= '0' then
-         dPY = EgtIf( EMT.ROT == -1, EMT.HB, EMT.SB)
+         dPY = EgtIf( EMT.ROT == -1, EMT.HT, EMT.ST)
       end
       SimulMoveAxis( 'PY', dPY, MCH_SIM_STEP.RAPID)
       SetPYLight( Cmd[2] ~= '0')
    elseif Cmd[1] == '12' then
       local dPV = MaxOpen
       if Cmd[2] ~= '0' then
-         dPV = EgtIf( EMT.ROT == -1, EMT.HB, EMT.SB)
+         dPV = EgtIf( EMT.ROT == -1, EMT.HT, EMT.ST)
       end
       SimulMoveAxis( 'PV', dPV, MCH_SIM_STEP.RAPID)
       SetPVLight( Cmd[2] ~= '0')
@@ -990,7 +1008,7 @@ function ExecUnloading()
       -- li sposto per lasciare spazio al nuovo pezzo
       local nId = EgtGetFirstInGroup( nVmGrpId)
       while nId do
-         EgtMove( nId, Vector3d( 0, EgtIf( BD.RIGHT_LOAD, ( EMT.SB + 50.0), -( EMT.SB + 50.0)), 0), GDB_RT.GLOB)
+         EgtMove( nId, Vector3d( 0, EgtIf( BD.RIGHT_LOAD, ( EMT.ST + 50.0), -( EMT.ST + 50.0)), 0), GDB_RT.GLOB)
          nId = EgtGetNext( nId)
       end
       -- creo un nuovo layer e vi inserisco il nuovo pezzo
@@ -1208,6 +1226,18 @@ local FALL_T = 2  * ESTIMATION_RAPID_COEFF              -- s
 ---------------------------------------------------------------------
 function OnEstimStart()
    EMT.INCHES = not EgtUiUnitsAreMM()      -- unità di misura mm/inches
+
+   -- TPA
+   if NumericalControl == 'TPA' then
+      EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+      EMT.MAXACC = MaxAcc or 4000    -- accelerazione massima pinze. In realtà è il tempo in millisecondi, quindi MAXACC corrisponde al tempo massimo per raggiungere la velocità desiderata
+      EMT.MINACC = MinAcc or 300     -- accelerazione minima pinze. In realtà è il tempo in millisecondi, quindi MINACC corrisponde al tempo massimo per raggiungere la velocità desiderata
+   -- NUM_PLUS e NUM
+   else
+      EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+      EMT.MAXACC = MaxAcc or ( EMT.FMAXPINZE / ( 60 * 0.3))  -- accelerazione massima pinze
+      EMT.MINACC = MinAcc or ( EMT.FMAXPINZE / ( 60 * 4))    -- accelerazione minima pinze
+   end
 end
 
 ---------------------------------------------------------------------
@@ -1293,6 +1323,15 @@ function OnEstimDispositionEnd()
    EMT.OPEISDISP = false
 end
 
+---------------------------------------------------------------------
+function OnEstimRawMoveData()
+   -- se start del pezzo
+   if IsStartOrRestPhase( EMT.PHASE) then
+      EMT.SPLIT = false
+   end
+   OnRawMoveData()
+end
+
 ---------------------------------------------------------------------
 function OnEstimToolSelect()
    -- reset indice utensile in tabella lunghezze
@@ -1349,6 +1388,12 @@ function OnEstimMachiningEnd()
       EMT.TLE_NAME = nil
       EMT.TLE_TIME = nil
    end
+
+   EMT.MCHUSERNOTES = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   EMT.MCHSPLIT = ( EMT.MCHUSERNOTES:find( 'Split;', 1, true) ~= nil)
+   if EMT.MCHSPLIT then
+      EMT.SPLIT = true
+   end
 end
 
 ---------------------------------------------------------------------
@@ -1479,11 +1524,11 @@ function OnEstimRapid()
    EMT.MCHEXTLEN = EMT.MCHEXTLEN + dLen
    -- calcolo tempo
    local dTime = RAPID_MIN_T
-   local dT1 = abs( dL1) / RAPID_X_FEED * 60
+   local dT1 = CalcMoveTime( abs( dL1), RAPID_X_FEED, EMT.SPLIT)
    if dT1 > dTime then dTime = dT1 end
-   local dT2 = abs( dL2) / RAPID_Y_FEED * 60
+   local dT2 = CalcMoveTime( abs( dL2), EMT.FMAXPINZE, EMT.SPLIT)
    if dT2 > dTime then dTime = dT2 end
-   local dT3 = abs( dL3) / RAPID_Z_FEED * 60
+   local dT3 = CalcMoveTime( abs( dL3), RAPID_Z_FEED, EMT.SPLIT)
    if dT3 > dTime then dTime = dT3 end
    local dT4 = abs( dR1) / RAPID_C_FEED * 60
    if dT4 > dTime then dTime = dT4 end
@@ -1505,7 +1550,7 @@ function OnEstimLinear()
    local dLen = sqrt( dL1 * dL1 + dL2 * dL2 + dL3 * dL3)
    EMT.MCHCUTLEN = EMT.MCHCUTLEN + dLen
    -- calcolo tempo
-   local dTime = dLen / EMT.F * 60
+   local dTime = CalcMoveTime( dLen, EMT.F, EMT.SPLIT)
    EMT.MCHCUTTIME = EMT.MCHCUTTIME + dTime
    EgtOutLog( string.format( '  G1 Len=%.0f Time=%.2f', dLen, dTime), 5)
    -- aggiorno valori come precedenti
@@ -1652,6 +1697,70 @@ function GetParkT()
    end
 end
 
+---------------------------------------------------------------------
+function CalcDinamicaPinze_TPA( dH, dS, dL)
+   local MinTempoAcc = EMT.MINACC        -- [ms] ~300
+   local MaxTempoAcc = EMT.MAXACC        -- [ms] ~4000
+   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
+   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
+   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
+   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
+   local TempoAcc = EgtClamp( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito), MinTempoAcc, MaxTempoAcc)
+   local RidFeed = 100 / Massa * 100
+   if RidFeed > 100 then
+      RidFeed = 100
+   elseif RidFeed < 10 then
+      RidFeed = 10
+   end
+   return TempoAcc, MinTempoAcc, RidFeed
+end
+
+---------------------------------------------------------------------
+function CalcDinamicaPinze_NUM( dH, dS, dL)
+   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
+   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
+   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
+   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
+   local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito) / 1000)
+   local AccMaxPinze = EMT.MAXACC
+   local AccPinze = EgtClamp( FMaxPinze / ( 60 * TempoAcc), EMT.MINACC, EMT.MAXACC)
+   local RidFeed = 100 / Massa * 100
+   if RidFeed > 100 then
+      RidFeed = 100
+   elseif RidFeed < 10 then
+      RidFeed = 10
+   end
+   return AccPinze, AccMaxPinze, RidFeed, TempoAcc
+end
+
+---------------------------------------------------------------------
+function CalcMoveTime( dPathLen, dFeed, bIsSplitted)
+   local dTime
+   local dFeedInSec = dFeed / 60
+
+   if NumericalControl == 'TPA' then
+      local dTempoAcc, _, _ = CalcDinamicaPinze_TPA( EMT.HT, EMT.ST, EgtIf( bIsSplitted, EMT.LT, EMT.LB))
+      dTempoAcc = dTempoAcc / 1000
+      -- se si raggiunge la velocità massima
+      if dPathLen >= dFeedInSec * dTempoAcc then
+         dTime = dTempoAcc * 2 + ( ( dPathLen - dFeedInSec * dTempoAcc) / dFeedInSec)
+      else
+         dTime = 2 * sqrt( (dPathLen * dTempoAcc) / dFeedInSec)
+      end
+   else
+      local dAcc, _, _, _ = CalcDinamicaPinze_NUM( EMT.HT, EMT.ST, EgtIf( bIsSplitted, EMT.LT, EMT.LB))
+      -- Caso 1: dFeed raggiunta
+      if dPathLen >= ( dFeedInSec ^ 2) / dAcc then
+         dTime = ( dFeedInSec / dAcc) + ( dPathLen / dFeedInSec)
+      -- Caso 2: dFeed non raggiunta
+      else
+         dTime = 2 * sqrt( dPathLen / dAcc)
+      end
+   end
+
+   return dTime
+end
+
 ---------------------------------------------------------------------
 -- *** END GENERAL ***
 ---------------------------------------------------------------------

Common_FAST.mlse

@@ -931,7 +931,7 @@ function SpecCalcEncumbrance( vtTool, vtArm, ptMin, ptMax, bSaw, bChain, dTLen,
    local dHeadBack = 350
    if bSaw then
       if vtTool:getX() > 0 and abs( vtTool:getY()) < 0.088 and abs( vtTool:getZ()) < 0.088 then
-         dHeadBack = 50 + 0.5 * dTDiam * sqrt( 1 - vtTool:getX() * vtTool:getX())
+         dHeadBack = 50 + 0.5 * dTDiam * sqrt( 1 - vtTool:getX() * vtTool:getX()) + EgtIf( EMC.CNT == 1, 10, 0)
       elseif abs( vtTool:getZ()) < 0.26 and abs( vtTool:getX()) < 0.35 then
          dHeadBack = EgtIf( vtArm:getX() < 0, 540, 350)
       elseif abs( vtTool:getZ()) < 0.26 and abs( vtTool:getX()) < 0.71 then
@@ -1022,7 +1022,7 @@ function SpecCalcEncumbrance( vtTool, vtArm, ptMin, ptMax, bSaw, bChain, dTLen,
    local dHeadFront = 350
    if bSaw then
       if vtTool:getX() < 0 and abs( vtTool:getY()) < 0.088 and abs( vtTool:getZ()) < 0.088 then
-         dHeadFront = 50 + 0.5 * dTDiam * sqrt( 1 - vtTool:getX() * vtTool:getX())
+         dHeadFront = 50 + 0.5 * dTDiam * sqrt( 1 - vtTool:getX() * vtTool:getX()) + EgtIf( EMC.CNT == 1, 10, 0)
       elseif abs( vtTool:getZ()) < 0.26 and abs( vtTool:getX()) < 0.35 then
          dHeadFront = EgtIf( vtArm:getX() > 0, 540, 350)
       elseif abs( vtTool:getZ()) < 0.26 and abs( vtTool:getX()) < 0.71 then
@@ -1642,7 +1642,9 @@ function SpecAdjustCarriages( vCmd, dTPosI, dYDeltaI, dVDeltaI, dTPosF, dYDeltaF
       --    * deve effettivamente spostarsi
       --    * non si arriva da gestione passo del pellegrino
       --    * se riesce a raggiungere la posizione con le corse a disposizione per come sono posizionate le morse attualmente
-      if ( dYDeltaI - dVDeltaF) + 10 * GEO.EPS_SMALL >= MyMinY - MaxV and abs( dVDeltaF - dVDeltaI) > 10 * GEO.EPS_SMALL and  not EMC.PILGRIMSTEP and
+      if ( dYDeltaI - dVDeltaF) + 10 * GEO.EPS_SMALL >= MyMinY - MaxV and
+         ( abs( dVDeltaF - dVDeltaI) > 10 * GEO.EPS_SMALL or not EMC.VDELTA) and
+         not EMC.PILGRIMSTEP and
          ( dVDeltaF - dVDeltaI > MinV - dVPosI + MyMinY - dYPosI) then
          table.insert( vCmd, { 0, 'Direct-V-Y'})
          -- se l'altra morsa non era in presa, vado a pinzare il pezzo
@@ -1747,7 +1749,9 @@ function SpecAdjustCarriages( vCmd, dTPosI, dYDeltaI, dVDeltaI, dTPosF, dYDeltaF
       --    * deve effettivamente spostarsi
       --    * non si arriva da gestione passo del pellegrino
       --    * se riesce a raggiungere la posizione con le corse a disposizione per come sono posizionate le morse attualmente
-      elseif ( dYDeltaF - dVDeltaI) + 10 * GEO.EPS_SMALL >= MyMinY - MaxV and abs( dYDeltaF - dYDeltaI) > 10 * GEO.EPS_SMALL and  not EMC.PILGRIMSTEP and
+      elseif ( dYDeltaF - dVDeltaI) + 10 * GEO.EPS_SMALL >= MyMinY - MaxV and 
+             ( abs( dYDeltaF - dYDeltaI) > 10 * GEO.EPS_SMALL or not EMC.YDELTA) and
+             not EMC.PILGRIMSTEP and
              ( dYDeltaF - dYDeltaI < MaxY - dYPosI + MaxV - dVPosI) then
          table.insert( vCmd, { 0, 'Direct-Y-V'})
          -- se l'altra morsa non era in presa, vado a pinzare il pezzo

UpdateLog.txt

@@ -1,5 +1,31 @@
            ==== Common_FAST Update Log ====
 
+Versione 2.7j2 (08/10/2025)
+- (SIM-GEN) Quando si scarica motosega, si raddrizza prima l'asse B e poi si muove il C. Ora sempre e non solo se pezzo alto.
+
+Versione 2.7j1 (06/10/2025)
+- (SIM-GEN) Quando si scarica motosega, si raddrizza prima l'asse B e poi si muove il C.
+
+Versione 2.7i3 (23/09/2025)
+- (MLDE-ALL) Spostate costanti dimensioni utensili in MLDE.
+
+Versione 2.7i2 (17/09/2025)
+- (EST) Stima tempi considerando accelerazioni
+- (SIM) Prelievo e deposito motosega con gli angoli comunicati da Essetre
+
+Versione 2.7i1 (08/09/2025)
+- (SIM-GEN) Se lavorazione precedente e successiva con motosega e si cambiano assi rotanti, vado in parcheggio per ruotare. Ticket#1844
+- (SIM-GEN) Per NEWCLAMPING, corretto un caso di riposizionemento allo scarico dove la pinza V poteva andare in posizione direttamente, ma cercava di fare passo pellegrino. Ticket#2572
+
+Versione 2.7g1 (01/07/2025)
+- (GEN) Aggiunti parametri FMAXPINZE, MAXACC, MINACC configurabili da TS3. Ticket#2052
+
+Versione 2.7f3 (26/06/2025)
+- (SIM-GEN) Aggiunti 10mm di sicurezza in caso di primo pinzaggio per stare oltre tolleranza riqualifica laser di 50mm. Ticket#2504
+
+Versione 2.7f2 (19/06/2025)
+- (GEN) Se in separazione il pezzo è andato più lontano della posizione standard, viene riletta. Ticket#2498
+
 Versione 2.7f1 (18/06/2025)
 - (SIM-GEN) Se utensile più lungo di 350mm, si va in posizione sicurezza come per la motosega. Ticket#2438
 

Version.lua

@@ -3,7 +3,7 @@
 
 local InfoCommon_STD_PP = {
    NAME = 'Common_FAST',            -- nome script PP standard
-   VERSION = '2.7f1',                 -- versione script
+   VERSION = '2.7j2',                 -- versione script
    MIN_MACH_VER_PP_COMMON = '2.5k1'   -- versione minima kernel
 }