In NGE mancava manina portautensile in posizione T11 quando c'era aggregato BH

.gitignore

@@ -1,6 +1,7 @@
 /Tools
 /Machinings
 /SetUp
+/Beam/AISetup
 /Beam/Ts3Data.bak
 /Beam/CutData.lua
 /Beam/DrillData.lua

Beam/BeamData.lua

@@ -117,6 +117,7 @@ if EgtExistsFile( sData) then
          if Machine.Offsets.FASTCLAMPING ~= nil then BeamData.FASTCLAMPING = ( Machine.Offsets.FASTCLAMPING == 1) end
          if Machine.Offsets.ROT90 ~= nil then BeamData.ROT90 = ( Machine.Offsets.ROT90 == 1) end
          if Machine.Offsets.ROT180 ~= nil then BeamData.ROT180 = ( Machine.Offsets.ROT180 == 1) end
+         if Machine.Offsets.CUT_SIC then BeamData.CUT_SIC = EgtClamp( Machine.Offsets.CUT_SIC, 15, 50) end
       end
       if Machine.Trave then
          BeamData.MIN_WIDTH = Machine.Trave.XMIN or BeamData.MIN_WIDTH
@@ -191,11 +192,7 @@ BeamData.GetChainSawInitAngs = GetChainSawInitAngs
 
 ---------------------------------------------------------------------
 local function GetMinNzTopHead( vtNFace)
-   if vtNFace and abs( vtNFace:getY()) > 0.8659 then
-      return -0.2499
-   else
-      return sin( -45)
-   end
+   return sin( -45)
 end
 
 ---------------------------------------------------------------------
@@ -214,7 +211,9 @@ local function GetMinNzDownUp( b3Raw, vtNFace, vtToolDirection)
           and ( vtNFace and ( abs( vtNFace:getY()) > 0.983))
           and ( b3Raw:getDimY() < 210) then
           
-          return -0.173
+      return -0.173
+   elseif vtToolDirection and abs( vtToolDirection:getX()) > 0.708 and abs( vtNFace:getX()) < 0.708 then
+      return -1
    else
       -- N_HorAng > 60°
       if vtNFace and ( abs( vtNFace:getY()) > 0.866) then

Beam/MachiningTypes.ini

@@ -33,6 +33,7 @@
 20=SmallToolContour
 21=AntiSplintMillCut
 22=Prof_end
+23=SideMillAsBlade
 
 [Pocketing]
 1=Pocket

Common_FAST.NUM.mlpe

@@ -635,15 +635,24 @@ function OnRapid()
          bGoToHome = true
       end
 
+      -- ricavo i dati per la lavorazione
+      local sEE = ' EE' .. EgtIf( bZmax, '3', '4')
+      local sEL = ' EL' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TLEN, ( EMT.TDIST or ChSawLen)), 3)
+      local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
+      local sES = ' ES'..EgtNumToString( EMT.S, 0)
+
       -- primo posizionamento
       local MyZHome = EgtGetAxisHomePos( 'Z')
       local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or  EMT.L3 > -1)
       -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and (EMT.ST > BeamHeightForFixRot or bGoToHome) and EMT.FLAG2 == 1 then
+      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.FLAG2 == 1 then
          local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
                                        ' B' .. EmtLenToString( EMT.R2pp, 3) .. ' C' .. EmtLenToString( EMT.R1pp, 3) .. 
                                        ' EE' .. EgtIf( bZmax, '3', '4') .. EMT.PREVsEL .. EMT.PREVsER .. EMT.PREVsET .. EMT.PREVsES
          EmtOutput( sOutPreMove)
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1pp, 3) .. sEE .. sEL .. sER .. sET .. sES
+         EmtOutput( sOutPreMove)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
       end
@@ -653,12 +662,6 @@ function OnRapid()
          EmtOutput( '( *** ' .. sOut .. ' *** )')
       end
 
-      -- ricavo i dati per la lavorazione
-      local sEE = ' EE' .. EgtIf( bZmax, '3', '4')
-      local sEL = ' EL' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TLEN, ( EMT.TDIST or ChSawLen)), 3)
-      local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
-      local sES = ' ES'..EgtNumToString( EMT.S, 0)
-
       -- se carico motosega, ruoto in zona sicura prima di approcciare la lavorazione
       if not EMT.LOAD and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and
          ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then

Common_FAST.NUM_PLUS.mlpe

@@ -684,24 +684,6 @@ function OnRapid()
          bGoToHome = true
       end
 
-      -- primo posizionamento
-      local MyZHome = EgtGetAxisHomePos( 'Z')
-      local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or  EMT.L3 > -1)
-      -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and ( EMT.ST > BeamHeightForFixRot or bGoToHome) and EMT.FLAG2 == 1 then
-         local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
-                                       ' B' .. EmtLenToString( EMT.R2pp, 3) .. ' C' .. EmtLenToString( EMT.R1pp, 3) .. 
-                                       ' EE' .. EgtIf( bZmax, '3', '4') .. EMT.PREVsEL .. EMT.PREVsER .. EMT.PREVsET .. EMT.PREVsES
-         EmtOutput( sOutPreMove)
-         EmtOutput( 'G101 ET1001')
-         EmtOutput( 'G101 ET2001')
-      end
-
-      if not EMT.LOAD then
-         local sOut = string.gsub( string.gsub( EMT.MCHNAME..'/'..EMT.TOOL, '%(', '-'), '%)', '-')
-         EmtOutput( '( *** ' .. sOut .. ' *** )')
-      end
-
       -- ricavo i dati per la lavorazione
       local sEE = ' EE' .. EgtIf( bZmax, '3', '4')
       
@@ -731,6 +713,27 @@ function OnRapid()
 
       local sES = ' ES'..EgtNumToString( EMT.S, 0)
 
+      -- primo posizionamento
+      local MyZHome = EgtGetAxisHomePos( 'Z')
+      local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or  EMT.L3 > -1)
+      -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
+      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.FLAG2 == 1 then
+         local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EmtLenToString( EMT.R2pp, 3) .. ' C' .. EmtLenToString( EMT.R1pp, 3) .. 
+                                       ' EE' .. EgtIf( bZmax, '3', '4') .. EMT.PREVsEL .. EMT.PREVsER .. EMT.PREVsET .. EMT.PREVsES
+         EmtOutput( sOutPreMove)
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
+         EmtOutput( sOutPreMove)
+         EmtOutput( 'G101 ET1001')
+         EmtOutput( 'G101 ET2001')
+      end
+
+      if not EMT.LOAD then
+         local sOut = string.gsub( string.gsub( EMT.MCHNAME..'/'..EMT.TOOL, '%(', '-'), '%)', '-')
+         EmtOutput( '( *** ' .. sOut .. ' *** )')
+      end
+
       -- se carico motosega, ruoto in zona sicura prima di approcciare la lavorazione
       if not EMT.LOAD and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and 
          ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then

Common_FAST.TPA.mlpe

@@ -669,12 +669,17 @@ function OnRapid()
       local MyZHome = EgtGetAxisHomePos( 'Z')
       local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or EMT.L3 > -1)
       -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and ( EMT.ST > BeamHeightForFixRot or bGoToHome) and EMT.FLAG2 == 1 then
+      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.FLAG2 == 1 then
          local sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
                                  ' P4=' .. EgtNumToString( EMT.R2pp, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1pp, EMT.DECMACRO) .. 
                                  ' P6=' .. EgtNumToString( EMT.PREVTCPOS, EMT.DECMACRO) .. ' P7=' .. EgtNumToString( EMT.PREVS, 0) ..
                                  ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
          EmtOutput( sOutPreMove)
+         sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+                                 ' P4=' .. EgtNumToString( 0, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1pp, EMT.DECMACRO) .. 
+                                 ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
+                                 ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
+         EmtOutput( sOutPreMove)
          EmtOutput( 'M101 P1=2')
          EmtOutput( 'M101 P1=3')
       end

Common_FAST.mlpe

@@ -556,9 +556,9 @@ function OnSimulToolDeselect()
       -- movimento scarico sega a catena
       if EMT.HEAD == 'H3' then
          -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-         if  EMT.HT > BeamHeightForFixRot then
-            SimulMoveAxis( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID)
-         end
+         SimulMoveAxis( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID)
+         -- raddrizzo asse B prima di ruotare il C
+         SimulMoveAxis( 'B', 0, MCH_SIM_STEP.COLLROT)
          local dPosA = EgtGetAxisPos( 'A')
          if abs( dPosA) < 0.1 then
             SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, -180, 0), MCH_SIM_STEP.COLLROT)
@@ -803,14 +803,14 @@ function OnSimulMoveStart()
       EMT.MCHFIRST = false
       local bZmax = ( EMT.TOOL ~= EMT.PREVTOOL  or EMT.L3 > -1)
       -- con pezzi alti aggiorno gli assi rotanti prima di muovermi sopra il pezzo
-      if not EMT.LOAD and EMT.MOVE == 0 and ( EMT.HT > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
+      if not EMT.LOAD and EMT.MOVE == 0 and ( EMT.HEAD == 'H3' or ( EMT.HEAD == 'H1' and EMT.TOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
          -- se motosega mi muovo a X di sicurezza per ruotare, prima si raddrizza B e poi C in posizione
-         if EMT.HEAD == 'H3' and bGoToHome then
+         if EMT.HEAD == 'H3' or bGoToHome then
             SimulMoveAxis( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID)
             SimulMoveAxis( 'B', 0, MCH_SIM_STEP.COLLROT)
             SimulMoveAxis( 'C', EMT.R1, MCH_SIM_STEP.COLLROT)
             SimulMoveAxis( 'B', EMT.R2, MCH_SIM_STEP.COLLROT)
-         elseif ( EMT.HEAD == 'H3' or ( bZmax and EMT.TOTLEN > 200)) then
+         elseif ( bZmax and EMT.TOTLEN > 200) then
             SimulMoveAxes( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID, 'C', EMT.R1, MCH_SIM_STEP.COLLROT, 'B', EMT.R2, MCH_SIM_STEP.COLLROT)
          end
       end

Essetre-FAST.mlde

@@ -24,8 +24,8 @@
 require( 'EmtGenerator')
 EgtEnableDebug( false)
 
-PP_VER = '2.7j1_DEV1'
-PP_NVER = '2.7.9.4'
+PP_VER = '2.7k4'
+PP_NVER = '2.7.11.4'
 MIN_MACH_VER = '2.7j1'
 MACH_NAME = string.match( EgtGetCurrMachineDir(), "[^\\]+$")  -- si ricava il nome della macchina dal direttorio
 
@@ -565,13 +565,6 @@ if SecondToolChanger then
          TDir = X_AX(),
          ADir = -Y_AX(),
          Geo = 'BASE/T28'}
-   EmtTcPos {
-         Name = 'T101',
-         Parent = 'Base',
-         Pos = Point3d( -510.4, 113.2, -1160.8),
-         TDir = X_AX(),
-         ADir = Z_AX(),
-         Geo = 'BASE/T101S'}
 else
    if not SpecialBH then
       EmtTcPos {
@@ -581,14 +574,6 @@ else
             TDir = X_AX(),
             ADir = Z_AX(),
             Geo = 'BASE/T101'}
-   else
-      EmtTcPos {
-            Name = 'T101',
-            Parent = 'Base',
-            Pos = Point3d( -510.4, 113.2, -1160.8),
-            TDir = X_AX(),
-            ADir = Z_AX(),
-            Geo = 'BASE/T101S'}
    end
    if SecondSupport == 1 then
       -- supporto per punta
@@ -609,19 +594,6 @@ else
                            ADir = Z_AX(),
                            Geo = 'BASE/T111M'}
       EgtSetInfo( TcpSsId, 'Mortiser', true)
-   elseif SecondSupport == 3 then
-      -- supporto per rinvio angolare
-      local TcpSsId = EmtTcPos {
-                           Name = 'T91',
-                           Parent = 'Base',
-                           ExitNbr = 2,
-                           Pos1 = Point3d( -710.4-150, 113.2, -329.8-170),
-                           TDir1 = X_AX(),
-                           Pos2 = Point3d( -710.4+150, 113.2, -329.8-170),
-                           TDir2 = -X_AX(),
-                           ADir = Z_AX(),
-                           Geo = 'BASE/T91',
-                           Aux = 'BASE/T91_HS'}
    end
    if SpecialBH then
       EmtTcPos {
@@ -633,6 +605,37 @@ else
             Geo = 'BASE/T111S'}
    end
 end
+-- motosega in caso di magazzino 2 o SpecialBH
+if SpecialBH or SecondToolChanger then
+   local TcpSsId = EmtTcPos {
+                        Name = 'T101',
+                        Parent = 'Base',
+                        Pos = Point3d( -510.4, 113.2, -1160.8),
+                        TDir = X_AX(),
+                        ADir = Z_AX(),
+                        Geo = 'BASE/T101S'}
+   -- spostamento in caso di magazzino 2
+   if SecondToolChanger then
+      EgtMove( TcpSsId, Vector3d( 0, 0, 140), GDB_RT.GLOB)
+   end
+end
+if SecondSupport == 3 then
+   -- supporto per rinvio angolare
+   local TcpSsId = EmtTcPos {
+                        Name = 'T91',
+                        Parent = 'Base',
+                        ExitNbr = 2,
+                        Pos1 = Point3d( -710.4-150, 113.2, -329.8-170),
+                        TDir1 = X_AX(),
+                        Pos2 = Point3d( -710.4+150, 113.2, -329.8-170),
+                        TDir2 = -X_AX(),
+                        ADir = Z_AX(),
+                        Geo = 'BASE/T91',
+                        Aux = 'BASE/T91_HS'}
+   if SecondToolChanger then
+      EgtMove( TcpSsId, Vector3d( 0, 0, -900), GDB_RT.GLOB)
+   end
+end
 
 -- Aggiusto posizioni geometriche
 local vtMove = Vector3d( 0, ( DeltaTabY - 913.16), ( DeltaTabZ + 830.037))

MachNotes.ini

@@ -22,7 +22,7 @@
 4=l,MaxOptSize,0
 
 [Mortising]
-0=d,MaxElev,0
+0=l,MaxElev,0
 
 [Chiseling]
 

Scripts/SetUp.lua

@@ -51,6 +51,9 @@ if IsTC2Active then
                            {Pos = "Pos19",  TcPos = "T26",  Head = "H1", Group = "G3"},
                            {Pos = "Pos20",  TcPos = "T27",  Head = "H1", Group = "G3"},
                            {Pos = "Pos21",  TcPos = "T28",  Head = "H1", Group = "G3"}}
+   if EgtGetHeadId( 'H5') then
+      table.insert( PositionTableTC2, {Pos = "Pos22", TcPos = "T91", Head = "H5", Group = "G2"})
+   end
    EgtJoinTables( PositionTable, PositionTableTC2)
 else
    local SecSuppId = EgtGetTcPosId( 'T111')

ToolNotes.ini

@@ -6,38 +6,38 @@
 
 [DRILL_STD]
 0=th,TH,
-1=d,STEP
-2=s,DOUBLE
+1=l,STEP
+2=tl,DOUBLE
 
 [SAW_STD]
 0=th,TH,
-1=d,STEP
-2=d,SIDESTEP
+1=l,STEP
+2=l,SIDESTEP
 3=b,LONGCUT
 
 [SAW_FLAT]
 0=th,TH,
-1=d,STEP
-2=d,SIDESTEP
+1=l,STEP
+2=l,SIDESTEP
 3=b,LONGCUT
 
 [MILL_STD]
 0=th,TH,
-1=d,STEP
-2=d,SIDESTEP
-3=d,SIDEDEPTH
-4=s,DOUBLE
-5=dr,TOOL_OVERHANG
+1=l,STEP
+2=l,SIDESTEP
+3=l,SIDEDEPTH
+4=tl,DOUBLE
+5=lr,TOOL_OVERHANG
 
 [MILL_NOTIP]
 0=th,TH,
-1=d,STEP
-2=d,SIDESTEP
-3=d,SIDEDEPTH
-4=s,DOUBLE
-5=dr,TOOL_OVERHANG
+1=l,STEP
+2=l,SIDESTEP
+3=l,SIDEDEPTH
+4=tl,DOUBLE
+5=lr,TOOL_OVERHANG
 
 [MORTISE_STD]
 0=b,MORTISE
-1=d,STEP
-2=d,SIDESTEP
+1=l,STEP
+2=l,SIDESTEP

UpdateLog.txt

@@ -1,5 +1,15 @@
            ==== Common_FAST Update Log ====
 
+Versione 2.7k1 (10/11/2025)
+- (GEN) Corretto set variabili info utensile prima del movimento in home in caso di pezzi alti per NUM/NUM_PLUS.
+
+Versione 2.7j2 (08/10/2025)
+- (SIM-GEN) Quando si scarica motosega, si raddrizza prima l'asse B e poi si muove il C. Ora sempre e non solo se pezzo alto.
+
+Versione 2.7j1 (06/10/2025)
+- (SIM-GEN) Quando si scarica motosega, si raddrizza prima l'asse B e poi si muove il C.
+- (MLDE-SIM) Controllo collisione tra utensile e TOP testa C. Serve CAM5 2.7j1
+
 Versione 2.7i3 (23/09/2025)
 - (MLDE-ALL) Spostate costanti dimensioni utensili in MLDE.
 

Version.lua

@@ -3,7 +3,7 @@
 
 local InfoCommon_STD_PP = {
    NAME = 'Common_FAST',            -- nome script PP standard
-   VERSION = '2.7i3',                 -- versione script
+   VERSION = '2.7k1',                 -- versione script
    MIN_MACH_VER_PP_COMMON = '2.5k1'   -- versione minima kernel
 }