Versione con gestione parametri HCING e TCING settabili su tutte le lavorazioni

Common_FAST.NUM_PLUS.mlpe

@@ -493,7 +493,7 @@ function OnMachiningEnd()
    end
    for i = 1, #EMT.AUXSTR do
       local sOut = EMT.AUXSTR[i]
-      if EMT.AUXTYPE == 'S' then
+      if EMT.AUXTYPE == 'S' and sOut:find( 'G101 ') then
          sOut = sOut .. ' EH1'
       elseif EMT.AUXTYPE == 'U' and not EMT.CHY_ON and not sOut:find( 'ET') then
          sOut = sOut .. ' ET2'

Common_FAST.mlpe

@@ -1133,18 +1133,19 @@ end
 ---------------------------------------------------------------------
 --   *** ESTIMATION T&L ***
 ---------------------------------------------------------------------
-local RAPID_X_FEED =  75000    -- mm/min
+local ESTIMATION_RAPID_COEFF = EstimationRapidMultiplier or 1
-local RAPID_Y_FEED = 100000    -- mm/min
+local RAPID_X_FEED =  75000 / ESTIMATION_RAPID_COEFF    -- mm/min
-local RAPID_Z_FEED =  50000    -- mm/min
+local RAPID_Y_FEED = 100000 / ESTIMATION_RAPID_COEFF    -- mm/min
-local RAPID_C_FEED =  15000    -- deg/min
+local RAPID_Z_FEED =  50000 / ESTIMATION_RAPID_COEFF    -- mm/min
-local RAPID_B_FEED =  15000    -- deg/min
+local RAPID_C_FEED =  15000 / ESTIMATION_RAPID_COEFF    -- deg/min
-local RAPID_MIN_T = 0.1        -- s
+local RAPID_B_FEED =  15000 / ESTIMATION_RAPID_COEFF    -- deg/min
-local LOAD_T = 2               -- s
+local RAPID_MIN_T = 0.1 * ESTIMATION_RAPID_COEFF       -- s
-local CHAR_ONE_MOVE_T = 1      -- s
+local LOAD_T = 2  * ESTIMATION_RAPID_COEFF              -- s
-local ROTATION_T = 40          -- s
+local CHAR_ONE_MOVE_T = 1  * ESTIMATION_RAPID_COEFF     -- s
-local SPLIT_T = 6              -- s
+local ROTATION_T = 40  * ESTIMATION_RAPID_COEFF         -- s
-local UNLOAD_T = 4             -- s
+local SPLIT_T = 6  * ESTIMATION_RAPID_COEFF             -- s
-local FALL_T = 2               -- s
+local UNLOAD_T = 4  * ESTIMATION_RAPID_COEFF            -- s
+local FALL_T = 2  * ESTIMATION_RAPID_COEFF              -- s
 
 ---------------------------------------------------------------------
 function OnEstimStart()

Common_FAST.mlse

@@ -7,11 +7,6 @@ EgtEnableDebug( false)
 -- carico librerie
 local BD = require( 'BeamData')
 
----------------------------------------------------------------------
--- *** Generic Machinings ***
----------------------------------------------------------------------
-require( 'EmtGenMachining')
-
 ---------------------- OnSpecialMoveZup -----------------------------
 ---------------------------------------------------------------------
 function OnSpecialMoveZup()
@@ -372,7 +367,18 @@ function OnSpecialApplyDisposition()
    EMC.HOVM = EgtGetInfo( nCurrRawId, 'HOVM', 'd') or 0
    EMC.HCING = EgtGetInfo( nCurrRawId, 'HCING', 'd') or 0
    EMC.TCING = EgtGetInfo( nCurrRawId, 'TCING', 'd') or 0
-   
+
+   -- correggo area non pinzabile in testa o coda in base alle info sulla lavorazione
+   local sNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   local dHCING = tonumber( EgtGetValInNotes( sNotes, 'HCING'))
+   if dHCING then
+      EMC.HCING = max( dHCING, -50)
+   end
+   local dTCING = tonumber( EgtGetValInNotes( sNotes, 'TCING'))
+   if dTCING then
+      EMC.TCING = max( dTCING, -50)
+   end
+
    -- Devo scaricare il pezzo o il grezzo rimasto
    -- Posizione trave
    local dPosT
@@ -516,6 +522,17 @@ function OnPostApplyMachining()
    local bSplitting = ( sNotes:find( 'Split') ~= nil)
    local bPreCut = ( sNotes:find( 'Precut') ~= nil)
    local bCutting = ( sNotes:find( 'Cut') ~= nil)
+
+   -- correggo area non pinzabile in testa o coda in base alle info sulla lavorazione
+   local dHCING = tonumber( EgtGetValInNotes( sNotes, 'HCING'))
+   if dHCING then
+      EMC.HCING = max( dHCING, -50)
+   end
+   local dTCING = tonumber( EgtGetValInNotes( sNotes, 'TCING'))
+   if dTCING then
+      EMC.TCING = max( dTCING, -50)
+   end
+
    local bUnload = IsEndPhase( EMC.PHASE) or IsEnd2Phase( EMC.PHASE)
    if bPreSplit or bPreCut then
       EgtSetInfo( EMC.MCHID, 'IS_PRE', '1')
@@ -639,6 +656,17 @@ function SpecApplyPath( bPreSplit, bSplitting, bPreCut, bCutting, bUnload, bPreR
    EMC.HOVM = EgtGetInfo( nCurrRawId, 'HOVM', 'd') or 0
    EMC.HCING = EgtGetInfo( nCurrRawId, 'HCING', 'd') or 0
    EMC.TCING = EgtGetInfo( nCurrRawId, 'TCING', 'd') or 0
+   
+   -- correggo area non pinzabile in testa o coda in base alle info sulla lavorazione
+   local sNotes = EgtGetMachiningParam( MCH_MP.USERNOTES)
+   local dHCING = tonumber( EgtGetValInNotes( sNotes, 'HCING'))
+   if dHCING then
+      EMC.HCING = max( dHCING, -50)
+   end
+   local dTCING = tonumber( EgtGetValInNotes( sNotes, 'TCING'))
+   if dTCING then
+      EMC.TCING = max( dTCING, -50)
+   end
 
    -- Calcolo dell'ingombro della lavorazione
    local dDistFront, dDistBack = SpecialCalcMachiningEncumbrance( EMC.MCHID, bPreCut)
@@ -1687,7 +1715,7 @@ function SpecAdjustCarriages( vCmd, dTPosI, dYDeltaI, dVDeltaI, dTPosF, dYDeltaF
             if abs( dYDeltaF - dYDeltaI) > 10 * GEO.EPS_SMALL then
                table.insert( vCmd, { 11, 0})
                dYPosA = max( MyMinY, dTPosI + dYDeltaF)
-               dTPosA = -( dYPosA + dVDeltaF)
+               dTPosA = dYPosA - dYDeltaF
                dVPosA = dTPosA + dVDeltaF
                table.insert( vCmd, { 3, 'Y', dYPosA , 'T', dTPosA, 'V', dVPosA})
                table.insert( vCmd, { 11, CalcCharStatus( 'Y', dYDeltaF)})

Essetre-FAST.mlde

@@ -24,8 +24,8 @@
 require( 'EmtGenerator')
 EgtEnableDebug( false)
 
-PP_VER = '2.7a1'
+PP_VER = '2.7a3_DEV1'
-PP_NVER = '2.7.1.1'
+PP_NVER = '2.7.1.3'
 MIN_MACH_VER = '2.5k1'
 MACH_NAME = 'Essetre-FAST'
 
@@ -90,6 +90,7 @@ BeamHeightForFixRot = 9999                     -- per abilitare assegnare 500
 NewTopC = true
 SafeXRotAxes = 150
 AggreBlockHaus = false
+EstimationRapidMultiplier = 1
 
 -- leggo e aggiorno con parametri da BeamData
 if BD then
@@ -158,6 +159,7 @@ if EgtExistsFile( sData) then
          if Machine.Offsets.MIN_JOIN_LL then MinJoinLL = Machine.Offsets.MIN_JOIN_LL end
          if Machine.Offsets.NEWTOPC then NewTopC = ( Machine.Offsets.NEWTOPC == 1) end
          if Machine.Offsets.AGGRE_BH then AggreBlockHaus = ( Machine.Offsets.AGGRE_BH == 1) end
+         if Machine.Offsets.COEFF_STIMATEMPI and Machine.Offsets.COEFF_STIMATEMPI > 0 then EstimationRapidMultiplier = Machine.Offsets.COEFF_STIMATEMPI end
       end
    end
 end

UpdateLog.txt

@@ -1,5 +1,12 @@
            ==== Common_FAST Update Log ====
 
+Versione 2.7a3 (08/01/2024)
+- (GEN) Dopo separazione, in NUM_PLUS, si srive EH1 solo se macro G101, perchè altrimenti non è prevista. Ticket#2239
+
+Versione 2.7a2 (08/01/2024)
+- (MLDE-SIM) Aggiunta gestione FACOLTATIVA 'EstimationRapidMultiplier' in MLDE per regolare il tempo stimato. Se non presente in MLDE, default 1.
+- (SIM) Aggiunta gestione qualità VMILL da impostazioni macchina
+
 Versione 2.7a1 (07/01/2024)
 - (MLDE-SIM-GEN) Nuovo aggregato 90° (H7) per fresa tipo BlockHaus. Ticket#2142
 - (SIM-GEN) Aumentati limiti massimi di pinzaggio minimo

Version.lua

@@ -1,9 +1,9 @@
--- Version.lua by EgalWare s.r.l. 2024/12/23
+-- Version.lua by EgalWare s.r.l. 2024/03/28
 -- Gestione della versione dei file comuni post-processori macchine FAST e FASTrl di Essetre
 
 local InfoCommon_STD_PP = {
    NAME = 'Common_FAST',            -- nome script PP standard
-   VERSION = '2.7a1',                 -- versione script
+   VERSION = '2.7a3',                 -- versione script
    MIN_MACH_VER_PP_COMMON = '2.5k1'   -- versione minima kernel
 }