- Allineamento con common ver. 2.6j2

- Aggiunta lettura parametro ROT90 da TS3 in BeamData

Beam/BeamData.lua

@@ -90,20 +90,21 @@ if EgtExistsFile( sData) then
    local Machine = dofile( sData)
    if Machine then
       if Machine.Offsets then
-        BeamData.ANG_TRASM = ( Machine.Offsets.SECSUP and Machine.Offsets.SECSUP >= 3)
-        BeamData.BH_MACHINE = ( Machine.Offsets.BLOCKHAUS == 1)
-        BeamData.MINRAW_S = max( BeamData.MINRAW_S, Machine.Offsets.MINRAW_S or BeamData.MINRAW_S)
-        BeamData.MINRAW_L = max( BeamData.MINRAW_L, Machine.Offsets.MINRAW_L or BeamData.MINRAW_L)
-        BeamData.CUT_EXTRA = Machine.Offsets.CUT_EXTRA or BeamData.CUT_EXTRA
-        BeamData.CUT_EXTRA_MIN = Machine.Offsets.CUT_EXTRA_MIN or BeamData.CUT_EXTRA_MIN
-        BeamData.DIM_STRIP_SMALL = Machine.Offsets.DIM_STRIP_SMALL or BeamData.DIM_STRIP_SMALL
-        BeamData.DIM_TO_CENTER_STRIP = Machine.Offsets.DIM_TO_CENTER_STRIP or BeamData.DIM_TO_CENTER_STRIP
-        BeamData.MAXDIAM_POCK_CORNER = Machine.Offsets.MAXDIAM_POCK_CORNER or BeamData.MAXDIAM_POCK_CORNER
-        if Machine.Offsets.PRECUT_HEAD_DISABLE then BeamData.PRECUT_HEAD = ( Machine.Offsets.PRECUT_HEAD_DISABLE == 0) end
-        if Machine.Offsets.PRECUT_TAIL_DISABLE then BeamData.PRECUT_TAIL = ( Machine.Offsets.PRECUT_TAIL_DISABLE == 0) end
-        if Machine.Offsets.MIN_HEIGHT_ADDED_CUTS then BeamData.MIN_HEIGHT_ADDED_CUTS = min( Machine.Offsets.MIN_HEIGHT_ADDED_CUTS, BeamData.MIN_HEIGHT_ADDED_CUTS) end
-        if Machine.Offsets.NEWCLAMPING ~= nil then BeamData.NEWCLAMPING = ( Machine.Offsets.NEWCLAMPING == 1) end
-        if Machine.Offsets.FASTCLAMPING ~= nil then BeamData.FASTCLAMPING = ( Machine.Offsets.FASTCLAMPING == 1) end
+         BeamData.ROT90 = Machine.Offsets.ROT90 or BeamData.ROT90
+         BeamData.ANG_TRASM = ( Machine.Offsets.SECSUP and Machine.Offsets.SECSUP >= 3)
+         BeamData.BH_MACHINE = ( Machine.Offsets.BLOCKHAUS == 1)
+         BeamData.MINRAW_S = max( BeamData.MINRAW_S, Machine.Offsets.MINRAW_S or BeamData.MINRAW_S)
+         BeamData.MINRAW_L = max( BeamData.MINRAW_L, Machine.Offsets.MINRAW_L or BeamData.MINRAW_L)
+         BeamData.CUT_EXTRA = Machine.Offsets.CUT_EXTRA or BeamData.CUT_EXTRA
+         BeamData.CUT_EXTRA_MIN = Machine.Offsets.CUT_EXTRA_MIN or BeamData.CUT_EXTRA_MIN
+         BeamData.DIM_STRIP_SMALL = Machine.Offsets.DIM_STRIP_SMALL or BeamData.DIM_STRIP_SMALL
+         BeamData.DIM_TO_CENTER_STRIP = Machine.Offsets.DIM_TO_CENTER_STRIP or BeamData.DIM_TO_CENTER_STRIP
+         BeamData.MAXDIAM_POCK_CORNER = Machine.Offsets.MAXDIAM_POCK_CORNER or BeamData.MAXDIAM_POCK_CORNER
+         if Machine.Offsets.PRECUT_HEAD_DISABLE then BeamData.PRECUT_HEAD = ( Machine.Offsets.PRECUT_HEAD_DISABLE == 0) end
+         if Machine.Offsets.PRECUT_TAIL_DISABLE then BeamData.PRECUT_TAIL = ( Machine.Offsets.PRECUT_TAIL_DISABLE == 0) end
+         if Machine.Offsets.MIN_HEIGHT_ADDED_CUTS then BeamData.MIN_HEIGHT_ADDED_CUTS = min( Machine.Offsets.MIN_HEIGHT_ADDED_CUTS, BeamData.MIN_HEIGHT_ADDED_CUTS) end
+         if Machine.Offsets.NEWCLAMPING ~= nil then BeamData.NEWCLAMPING = ( Machine.Offsets.NEWCLAMPING == 1) end
+         if Machine.Offsets.FASTCLAMPING ~= nil then BeamData.FASTCLAMPING = ( Machine.Offsets.FASTCLAMPING == 1) end
       end
       if Machine.Trave then
          BeamData.MIN_WIDTH = Machine.Trave.XMIN or BeamData.MIN_WIDTH

Common_FAST.mlse

@@ -1855,7 +1855,7 @@ function SpecAdjustCarriages( vCmd, dTPosI, dYDeltaI, dVDeltaI, dTPosF, dYDeltaF
                -- morsa Y arriva in posizione finale
                dYDeltaI = dYDeltaF
                dVPosA = MinV
-               dTPosA = dTPosI - MaxV + MinV
+               dTPosA = dTPosI - dVPosI + MinV
                dYPosA = dYDeltaF + dTPosA
                table.insert( vCmd, { 3, 'Y', dYPosA , 'T', dTPosA, 'V', dVPosA})
                table.insert( vCmd, { 11, 1})
@@ -1959,10 +1959,9 @@ function SpecAdjustCarriages( vCmd, dTPosI, dYDeltaI, dVDeltaI, dTPosF, dYDeltaF
             -- recupero una corsa massima e l'altra solo di quello che serve
             elseif abs( dVDeltaI - dVDeltaF) > dMaxMovePilgrimStepSingleClampV then
                -- aggiorno nuova posizione della morsa al carico dopo riposizionamento
-               local dTotMove = MaxY - dTPosI - dYDeltaI
                dVDeltaI = dVDeltaF
                dYPosA = MaxY
-               dTPosA = dTPosI + dTotMove
+               dTPosA = dTPosI + ( MaxY - dYPosI)
                dVPosA = dVDeltaF + dTPosA
                table.insert( vCmd, { 3, 'Y', dYPosA , 'T', dTPosA, 'V', dVPosA})
                table.insert( vCmd, { 12, 1})

Essetre-FAST.mlde

@@ -70,12 +70,14 @@
 -- 2024/09/24 AV ver 2.6i9 Allineamento con common ver. 2.6i5
 -- 2024/09/25 AV ver 2.6i10 Allineamento con common ver. 2.6i6
 -- 2024/10/01 AV ver 2.6j1 Allineamento con common ver. 2.6j1
+-- 2024/10/03 AV ver 2.6j2 Allineamento con common ver. 2.6j2
+--                         Aggiunta lettura parametro ROT90 da TS3 in BeamData
 
 require( 'EmtGenerator')
 EgtEnableDebug( false)
 
-PP_VER = '2.6j1'
-PP_NVER = '2.6.10.1'
+PP_VER = '2.6j2'
+PP_NVER = '2.6.10.2'
 MIN_MACH_VER = '2.5k1'
 MACH_NAME = 'Essetre-FAST'
 

UpdateLog.txt

@@ -1,5 +1,8 @@
            ==== Common_FAST Update Log ====
 
+Versione 2.6j2 (03/10/2024)
+- (SIM-GEN) Piccola correwzione calcolo posizione carrello durante riposizionamento, nuova gestione
+
 Versione 2.6j1 (01/10/2024)
 - (SIM-GEN) Sistemato calcolo in nuova disposzione carrelli
 

Version.lua

@@ -3,7 +3,7 @@
 
 local InfoCommon_STD_PP = {
    NAME = 'Common_FAST',            -- nome script PP standard
-   VERSION = '2.6j1',                 -- versione script
+   VERSION = '2.6j2',                 -- versione script
    MIN_MACH_VER_PP_COMMON = '2.5k1'   -- versione minima kernel
 }