- in DtMortise -> CalcPathAtHeight ora lo spostamento viene fatto correttamente anche nel caso di più curve

LuaLibs/BeamExec.lua

@@ -443,7 +443,7 @@ local function CalcHeadTailMachBeforeIntersDrillings( vProc, b3Raw)
    for i = 1, #vProc do
       local Proc = vProc[i]
       if Proc.Box and not Proc.Box:isEmpty() then
-         if Proc.Fct == 1 and BL.IsFeatureCuttingEntireSection( Proc.Box, b3Raw:getDimY(), b3Raw:getDimZ()) and ( Proc.Head or Proc.Tail) and Proc.Prc ~= 340 and Proc.Prc ~= 350 then
+         if Proc.Fct == 1 and BL.IsFeatureCuttingEntireSection( Proc.Box, b3Raw:getDimY(), b3Raw:getDimZ()) and ( Proc.Head or Proc.Tail) and Proc.Prc ~= 350 then
             if Proc.Head and Proc.Box:getCenter():getX() < dHeadX then
                dHeadX = Proc.Box:getCenter():getX()
                nHeadId = Proc.Id
@@ -2211,14 +2211,14 @@ function GetFeatureInfoAndDependency( vProc, b3Raw, nPartId)
                   Proc.PassedByHole = true
                end
                -- se taglio attraversato da foro, si definisce precedenza in base ad angolo
-               if Drill.Identify( Proc) and Cut.Identify( ProcB) and Overlaps( Proc.Box, ProcB.Box) then
+               if Drill.Identify( Proc) and ( Cut.Identify( ProcB) or ProcB.Prc == 340 or ProcB.Proc == 350) and Overlaps( Proc.Box, ProcB.Box) then
                   -- recupero e verifico l'entità foro
                   local DrillAuxId = ( EgtGetInfo( Proc.Id, 'AUXID', 'i') or 0) + Proc.Id
                   local vtDrillExtr = EgtCurveExtrusion( DrillAuxId, GDB_RT.GLOB)
                   local bOpen = ( Proc.Fce ~= 0) and ( Proc.Fce ~= Proc.Fcs)
                   local ptCut, vtCutN = EgtSurfTmFacetCenter( ProcB.Id, 0, GDB_ID.ROOT)
                   local dMaxAngleDrillOnCut = BD.MAX_ANGLE_DRILL_CUT or 10
-                  if GetAngle( vtDrillExtr, vtCutN) > dMaxAngleDrillOnCut then
+                  if ( GetAngle( vtDrillExtr, vtCutN) > dMaxAngleDrillOnCut) and not ( ProcB.Prc == 340 or ProcB.Proc == 350) then
                      if bOpen and GetAngle( -vtDrillExtr, vtCutN) < dMaxAngleDrillOnCut then
                         ProcB.Dependency = {}
                         ProcB.Dependency.ExecBefore = Proc

LuaLibs/ProcessDrill.lua

@@ -541,11 +541,13 @@ function ProcessDrill.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
    if not bToInvert and Proc.Flg == 1 and bOpen and abs( vtExtr:getZ()) < 0.259 and abs( vtExtr:getY()) > 0.966 then
       local Tool = BL.GetToolFromMachining( sDrilling)
       -- lato testa e lato di lavoro devono corrispondere
-      if ( ( Tool.PreferredSide.bFront == true) and vtExtr:getY() > 10 * GEO.EPS_SMALL)
-         or ( ( Tool.PreferredSide.bBack == true) and vtExtr:getY() < - 10 * GEO.EPS_SMALL) then
-         ptCen = ptCen - vtExtr * dLen
-         vtExtr = - vtExtr
-         bToInvert = true
+      if Tool.PreferredSide then
+         if ( ( Tool.PreferredSide.bFront == true) and vtExtr:getY() > 10 * GEO.EPS_SMALL)
+            or ( ( Tool.PreferredSide.bBack == true) and vtExtr:getY() < - 10 * GEO.EPS_SMALL) then
+            ptCen = ptCen - vtExtr * dLen
+            vtExtr = - vtExtr
+            bToInvert = true
+         end
       end
    end
    -- Determino la faccia di inizio del foro e dati correlati 

LuaLibs/ProcessDtMortise.lua

@@ -136,9 +136,11 @@ local function CalcPathAtHeight( nProcId, AuxId, nAddGrpId, dHeight, dSideAng, b
    local vtBoxDiag = b3Solid:getMax() - b3Solid:getMin()
    local nCount
    NewAuxId, nCount = EgtTrimFlatCurveWithBox( NewAuxId, refBox, vtBoxDiag, true, true, GDB_RT.GLOB)
-   -- eseguo traslazione e offset per portarla sul top
+   -- per ogni curva creata, eseguo traslazione e offset per portarla sul top
    local vtMove = EgtCurveExtrusion( AuxId, GDB_RT.GLOB) * ( dHeight - 10 * GEO.EPS_SMALL)
-   EgtMove( NewAuxId, vtMove, GDB_RT.GLOB)
+   for i = 1, nCount do
+      EgtMove( NewAuxId + i - 1, vtMove, GDB_RT.GLOB)
+   end
    -- se divisa in più parti, le unisco congiungendole con segmenti
    if nCount > 1 then
       if EgtGetType( NewAuxId) ~= GDB_TY.CRV_COMPO then
@@ -147,7 +149,7 @@ local function CalcPathAtHeight( nProcId, AuxId, nAddGrpId, dHeight, dSideAng, b
       for i = 2, nCount do
          local CrvId = NewAuxId + i - 1
          local ptStart = EgtSP( CrvId)
-         EgtAddCurveCompoLine( NewAuxId, ptStart) 
+         EgtAddCurveCompoLine( NewAuxId, ptStart)
          EgtAddCurveCompoCurve( NewAuxId, CrvId)
       end
    end

LuaLibs/ProcessLapJoint.lua

@@ -2458,6 +2458,83 @@ local function MakeContourByMill( Proc, idContourPath, vtTunnelDirection, dTunne
 
    local bOppositMillingReachesHalfDepth = ToolOpposite.MaxDepth > dTunnelDepth / 2 + dCollSic - dDimStrip / 2
 
+   -- eventuale lavorazione opposta
+   local bMillingOppositeOk
+   if bOppositeMillingNeeded then
+      local sName = 'ContourOppo_' .. ( EgtGetName( Proc.Id) or tostring( Proc.Id))
+      local idMachining = EgtAddMachining( sName, sMillingOpposite)
+      if not idMachining then
+         local sErr = 'Error : impossible add machining ' .. sName .. '-' .. sMilling
+         return false, sErr
+      end
+      -- geometria
+      EgtSetMachiningGeometry( {{ idContourPath, -1}})
+      -- lato di lavoro sinistro
+      EgtSetMachiningParam( MCH_MP.WORKSIDE, MCH_MILL_WS.RIGHT)
+      -- inversione direzione utensile
+      EgtSetMachiningParam( MCH_MP.TOOLINVERT, true)
+      -- SCC
+      local nSCC = MCH_SCC.NONE
+      if not BD.C_SIMM then
+         if AreSameOrOppositeVectorApprox( vtTunnelDirection, Z_AX()) then
+            nSCC = MCH_SCC.ADIR_YM
+         elseif abs( vtTunnelDirection:getX()) < 0.1 then
+            nSCC = EgtIf( BL.IsPartFinalPhase( nPhase), MCH_SCC.ADIR_XM, MCH_SCC.ADIR_XP)
+         elseif vtTunnelDirection:getY() < GEO.EPS_SMALL then
+            nSCC = MCH_SCC.ADIR_YM
+         else
+            nSCC = MCH_SCC.ADIR_YP
+         end
+      end
+      EgtSetMachiningParam( MCH_MP.SCC, nSCC)
+      -- gestione attacco e uscita
+      if EgtCurveIsClosed( idContourPath) then
+         -- attacco e uscita a quarto di cerchio senza allungamenti a inizio e fine
+         EgtSetMachiningParam( MCH_MP.LEADINTYPE, MCH_MILL_LI.TANGENT)
+         EgtSetMachiningParam( MCH_MP.LEADOUTTYPE, MCH_MILL_LO.AS_LI)
+         EgtSetMachiningParam( MCH_MP.LITANG, 0)
+         EgtSetMachiningParam( MCH_MP.LIPERP, 0.5 * Tool.Diameter)
+         EgtSetMachiningParam( MCH_MP.LIELEV, 0)
+         EgtSetMachiningParam( MCH_MP.STARTADDLEN, 0)
+         EgtSetMachiningParam( MCH_MP.ENDADDLEN, 0)
+      else
+         -- nessun attacco e uscita, allungo inizio e fine di raggio utensile + 5mm (per evitare controllo collisioni)
+         EgtSetMachiningParam( MCH_MP.LEADINTYPE, MCH_MILL_LI.NONE)
+         EgtSetMachiningParam( MCH_MP.LEADOUTTYPE, MCH_MILL_LO.AS_LI)
+         EgtSetMachiningParam( MCH_MP.STARTADDLEN, Tool.Diameter / 2 + 5)
+         EgtSetMachiningParam( MCH_MP.ENDADDLEN, Tool.Diameter / 2 + 5)
+      end
+      -- affondamento - la curva è a metà tasca quindi affondamento 0 significa che la lavorazione arriva a metà tasca
+      local dDepth
+      -- si arriva a metà tasca
+      if bOppositMillingReachesHalfDepth then
+         dDepth = -dDimStrip / 2
+      -- si arriva al massimo raggiungibile
+      else
+         dDepth = Tool.MaxDepth - dTunnelDepth / 2 - dCollSic
+         bIncomplete = true
+      end
+      EgtSetMachiningParam( MCH_MP.DEPTH, dDepth)
+      -- Note utente con dichiarazione nessuna generazione sfridi per Vmill e massima elevazione
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'VMRS', 0)
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dTunnelDepth / 2 + dDepth, 1))
+      EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
+      -- eseguo
+      if ML.ApplyMachining( true, false) then
+         _, sApplyWarning = EgtGetMachMgrWarning( 0)
+         if EgtIsMachiningEmpty() then
+            EgtSetOperationMode( idMachining, false)
+         end
+         bMillingOppositeOk = true
+      -- altrimenti lavorazione non applicata
+      else
+         _, sApplyWarning = EgtGetLastMachMgrError()
+         EgtSetOperationMode( idMachining, false)
+         bMillingOppositeOk = false
+      end
+   end
+
    -- applicazione lavorazione lato principale
    local sName = 'Contour_' .. ( EgtGetName( Proc.Id) or tostring( Proc.Id))
    local idMachining = EgtAddMachining( sName, sMilling) 
@@ -2546,83 +2623,6 @@ local function MakeContourByMill( Proc, idContourPath, vtTunnelDirection, dTunne
       bMillingOk = false
    end
 
-   -- eventuale lavorazione opposta
-   local bMillingOppositeOk
-   if bOppositeMillingNeeded then
-      local sName = 'ContourOppo_' .. ( EgtGetName( Proc.Id) or tostring( Proc.Id))
-      local idMachining = EgtAddMachining( sName, sMillingOpposite)
-      if not idMachining then
-         local sErr = 'Error : impossible add machining ' .. sName .. '-' .. sMilling
-         return false, sErr
-      end
-      -- geometria
-      EgtSetMachiningGeometry( {{ idContourPath, -1}})
-      -- lato di lavoro sinistro
-      EgtSetMachiningParam( MCH_MP.WORKSIDE, MCH_MILL_WS.RIGHT)
-      -- inversione direzione utensile
-      EgtSetMachiningParam( MCH_MP.TOOLINVERT, true)
-      -- SCC
-      local nSCC = MCH_SCC.NONE
-      if not BD.C_SIMM then
-         if AreSameOrOppositeVectorApprox( vtTunnelDirection, Z_AX()) then
-            nSCC = MCH_SCC.ADIR_YM
-         elseif abs( vtTunnelDirection:getX()) < 0.1 then
-            nSCC = EgtIf( BL.IsPartFinalPhase( nPhase), MCH_SCC.ADIR_XM, MCH_SCC.ADIR_XP)
-         elseif vtTunnelDirection:getY() < GEO.EPS_SMALL then
-            nSCC = MCH_SCC.ADIR_YM
-         else
-            nSCC = MCH_SCC.ADIR_YP
-         end
-      end
-      EgtSetMachiningParam( MCH_MP.SCC, nSCC)
-      -- gestione attacco e uscita
-      if EgtCurveIsClosed( idContourPath) then
-         -- attacco e uscita a quarto di cerchio senza allungamenti a inizio e fine
-         EgtSetMachiningParam( MCH_MP.LEADINTYPE, MCH_MILL_LI.TANGENT)
-         EgtSetMachiningParam( MCH_MP.LEADOUTTYPE, MCH_MILL_LO.AS_LI)
-         EgtSetMachiningParam( MCH_MP.LITANG, 0)
-         EgtSetMachiningParam( MCH_MP.LIPERP, 0.5 * Tool.Diameter)
-         EgtSetMachiningParam( MCH_MP.LIELEV, 0)
-         EgtSetMachiningParam( MCH_MP.STARTADDLEN, 0)
-         EgtSetMachiningParam( MCH_MP.ENDADDLEN, 0)
-      else
-         -- nessun attacco e uscita, allungo inizio e fine di raggio utensile + 5mm (per evitare controllo collisioni)
-         EgtSetMachiningParam( MCH_MP.LEADINTYPE, MCH_MILL_LI.NONE)
-         EgtSetMachiningParam( MCH_MP.LEADOUTTYPE, MCH_MILL_LO.AS_LI)
-         EgtSetMachiningParam( MCH_MP.STARTADDLEN, Tool.Diameter / 2 + 5)
-         EgtSetMachiningParam( MCH_MP.ENDADDLEN, Tool.Diameter / 2 + 5)
-      end
-      -- affondamento - la curva è a metà tasca quindi affondamento 0 significa che la lavorazione arriva a metà tasca
-      local dDepth
-      -- si arriva a metà tasca
-      if bOppositMillingReachesHalfDepth then
-         dDepth = -dDimStrip / 2
-      -- si arriva al massimo raggiungibile
-      else
-         dDepth = Tool.MaxDepth - dTunnelDepth / 2 - dCollSic
-         bIncomplete = true
-      end
-      EgtSetMachiningParam( MCH_MP.DEPTH, dDepth)
-      -- Note utente con dichiarazione nessuna generazione sfridi per Vmill e massima elevazione
-      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
-      sUserNotes = EgtSetValInNotes( sUserNotes, 'VMRS', 0)
-      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dTunnelDepth / 2 + dDepth, 1))
-      EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
-      -- eseguo
-      if ML.ApplyMachining( true, false) then
-         _, sApplyWarning = EgtGetMachMgrWarning( 0)
-         if EgtIsMachiningEmpty() then
-            EgtSetOperationMode( idMachining, false)
-         end
-         bMillingOppositeOk = true
-      -- altrimenti lavorazione non applicata
-      else
-         _, sApplyWarning = EgtGetLastMachMgrError()
-         EgtSetOperationMode( idMachining, false)
-         bMillingOppositeOk = false
-      end
-   end
-
    if bMillingOk or ( bOppositeMillingNeeded and bMillingOppositeOk) then
       local sWarning = ''
       if bIncomplete then