DataBeam 3.1a1 :

- aggiunta gestione UNLOAD da btm (come per LOAD90)
- ora UserNotes presenti nelle levarazioni in libreria vengono conservate.

BatchProcess.lua

@@ -144,6 +144,12 @@ local function UpdateAuxData( sAuxFile)
       EgtSetInfo( BtlInfoId, 'LOAD90', sLoad90)
       bModif = true
    end
+   -- Se definito UNLOAD, aggiorno
+   local sUnload = EgtGetStringFromIni( 'AuxData', 'UNLOAD', '', sAuxFile) 
+   if sUnload ~= '' then
+      EgtSetInfo( BtlInfoId, 'UNLOAD', sUnload)
+      bModif = true
+   end
    -- Se definito PROJID, aggiorno
    local sProjId = EgtGetStringFromIni( 'AuxData', 'PROJID', '', sAuxFile)
    if sProjId ~= '' then
@@ -241,7 +247,11 @@ if bToProcess then
       EgtEraseFile( sNgeFile)
       -- eseguo import
       EgtNewFile()
-      if not EgtImportBtl( BEAM.FILE, EIB_FL.TS3_POS + EIB_FL.USEUATTR) then
+      local nBtlFlag = EIB_FL.TS3_POS + EIB_FL.USEUATTR
+      if BD.USE_PART_OFFSET then
+         nBtlFlag = nBtlFlag + EIB_FL.PARTOFFSET
+      end
+      if not EgtImportBtl( BEAM.FILE, nBtlFlag) then
          BEAM.ERR = 13
          BEAM.MSG = 'Error importing BTL file : ' .. BEAM.FILE
          WriteErrToLogFile( BEAM.ERR, BEAM.MSG)
@@ -381,7 +391,7 @@ if bToProcess then
       end
    end
    
-      -- Verifico sezione barra non troppo piccola
+   -- Verifico sezione barra non troppo piccola
    if dRawW < BD.MIN_WIDTH - 10 * GEO.EPS_SMALL or dRawH < BD.MIN_HEIGHT - 10 * GEO.EPS_SMALL then
       local sOut = 'Sezione ('  .. EgtNumToString( dRawW, 2) .. ' x ' .. EgtNumToString( dRawH, 2) .. ') ' ..
                    'sotto i limiti della macchina (' .. EgtNumToString( BD.MIN_WIDTH, 2) .. ' x ' .. EgtNumToString( BD.MIN_HEIGHT, 2) .. ')'
@@ -391,6 +401,63 @@ if bToProcess then
       PostErrView( BEAM.ERR, BEAM.MSG)
       return
    end
+
+   -- Se presente offset da btl, verifico se offset uguale per tutti i pezzi
+   if BD.USE_PART_OFFSET then
+      vBeamErr = {}
+      local sPartOffset = EgtGetInfo( vBeam[1].Id, 'PARTOFFSET', 's') or ''
+      local vPartOffset = EgtSplitString( sPartOffset)
+      local dRotAng = EgtGetInfo( vBeam[1].Id, 'ROTATED_OK', 'd') or 0
+
+      for i = 2, #vBeam do
+         local sPartOffsetCurrent = EgtGetInfo( vBeam[i].Id, 'PARTOFFSET', 's') or ''
+         local vPartOffsetCurrent = EgtSplitString( sPartOffsetCurrent)
+         local dRotAngCurrent = EgtGetInfo( vBeam[i].Id, 'ROTATED_OK', 'd') or 0
+         local dRotAngDelta = abs( dRotAngCurrent - dRotAng)
+         if ( #vPartOffset == 5) and ( #vPartOffsetCurrent == 5) then
+            if dRotAngDelta < GEO.EPS_ANG_SMALL then
+               if ( vPartOffsetCurrent[2] ~= vPartOffsetCurrent[2])
+                  or ( vPartOffsetCurrent[3] ~= vPartOffset[3])
+                  or ( vPartOffsetCurrent[4] ~= vPartOffset[4])
+                  or ( vPartOffsetCurrent[5] ~= vPartOffset[5]) then
+                  
+                  table.insert( vBeamErr, i)
+               end
+            elseif dRotAngDelta - 180 < GEO.EPS_ANG_SMALL then
+               if ( vPartOffsetCurrent[2] ~= vPartOffsetCurrent[4])
+                  or ( vPartOffsetCurrent[3] ~= vPartOffset[5])
+                  or ( vPartOffsetCurrent[4] ~= vPartOffset[2])
+                  or ( vPartOffsetCurrent[5] ~= vPartOffset[3]) then
+                  
+                  table.insert( vBeamErr, i)
+               end
+            -- se pezzo ruotato di 90deg rispetto al principale, al momento si dà sempre errore
+            else
+               table.insert( vBeamErr, i)
+            end
+         else
+            if sPartOffsetCurrent ~= sPartOffset then
+               table.insert( vBeamErr, i)
+            end
+         end
+      end
+
+      if #vBeamErr > 0 then
+         local sOut = 'Part offset not consistent in beam(s) : '
+         for i = #vBeamErr, 1, -1 do
+            local sSeparator = ', '
+            if i == 1 then
+               sSeparator = ''
+            end
+            sOut = sOut .. vBeam[vBeamErr[i]].Name .. sSeparator
+         end
+         BEAM.ERR = 17
+         BEAM.MSG = sOut
+         WriteErrToLogFile( BEAM.ERR, BEAM.MSG)
+         PostErrView( BEAM.ERR, BEAM.MSG)
+         return
+      end
+   end
    
    -- Lunghezza della barra
    local dRawL = ( EgtGetInfo( EgtGetFirstNameInGroup( GDB_ID.ROOT, 'BtlInfo') or GDB_ID.NULL, 'BARLEN', 'd') or 12000) + 0.1

LuaLibs/BeamExec.lua

@@ -576,11 +576,6 @@ function BeamExec.ProcessBeams( dRawW, dRawH, dRawL, dOvmHead, dOvmMid, vBeam, b
    --  salvo nota con lunghezza grezzo
    -- Recupero l'identificativo del gruppo di lavoro corrente
    local nMGrpId = EgtGetCurrMachGroup()
-   -- Lunghezza della barra
-   local dBarLen = EgtGetInfo( nMGrpId, 'BARLEN', 'd')
-   if not dBarLen then
-      EgtSetInfo( nMGrpId, 'BARLEN', dRawL)
-   end
 
    -- Area tavola
    local b3Tab = EgtGetTableArea()
@@ -592,6 +587,18 @@ function BeamExec.ProcessBeams( dRawW, dRawH, dRawL, dOvmHead, dOvmMid, vBeam, b
    -- Impostazione dell'attrezzaggio di default
    EgtImportSetup()
 
+   -- se pretagli di coda sono attivi, aumento di 10mm la lunghezza del grezzo per fare effettivamente tagliare del materiale.
+   -- Altrimenti le lavorazioni pensano di essere nel vuoto e si muovono in rapido
+   if BD.PRECUT_TAIL and VerifyBigSectionCut( dRawW, dRawH) then
+      dRawL = dRawL + 10
+   end
+
+   -- Lunghezza della barra
+   local dBarLen = EgtGetInfo( nMGrpId, 'BARLEN', 'd')
+   if not dBarLen then
+      EgtSetInfo( nMGrpId, 'BARLEN', dRawL)
+   end
+
    -- Inserimento dei pezzi con il loro grezzo
    local Cnt = 0
    local Len = dRawL
@@ -608,16 +615,25 @@ function BeamExec.ProcessBeams( dRawW, dRawH, dRawL, dOvmHead, dOvmMid, vBeam, b
       local b3Part = EgtGetBBoxGlob( Pz or GDB_ID.NULL, GDB_BB.EXACT)
       local b3Solid = vBeam[i].Box
       if b3Part:isEmpty() or b3Solid:isEmpty() then break end
+      -- creo o pulisco gruppo geometrie aggiuntive
+      if not BL.CreateOrEmptyAddGroup( Pz) then
+         local sOut = 'Error creating Additional Group in Part ' .. tostring( Pz)
+         return false, sOut
+      end
       -- analizzo le features per valutare l'esistenza di feature head/tail che renderebbero inutili le rispettive finiture o di tagli di testa/coda sostituiti da cui leggere il parametro Q05
       local vProc = CollectFeatures( Pz, b3Solid, 0)
       local bSFinishingNeeded, nReplacedHeadCutFeatureId, nHeadCuttingFeatureId = AnalyzeHeadFeatures( b3Solid, vProc, dRawW, dRawH)
       local bEFinishingNeeded, nReplacedTailCutFeatureId, nTailCuttingFeatureId = AnalyzeTailFeatures( b3Solid, vProc, dRawW, dRawH)
-      -- Scrivo gli di delle facce di taglio custom: serviranno dopo per calcolare l'elevazione rispetto a queste
+      -- Scrivo gli id delle facce di taglio custom: serviranno dopo per calcolare l'elevazione rispetto a queste
       if nHeadCuttingFeatureId then
          EgtSetInfo( vBeam[i].Id, 'HEADCUTFEATUREID', nHeadCuttingFeatureId)
+      else
+         EgtRemoveInfo( vBeam[i].Id, 'HEADCUTFEATUREID')
       end
       if nTailCuttingFeatureId then
          EgtSetInfo( vBeam[i].Id, 'TAILCUTFEATUREID', nTailCuttingFeatureId)
+      else
+         EgtRemoveInfo( vBeam[i].Id, 'TAILCUTFEATUREID')
       end
       if bBigSectionCut then
          -- lascio in coda solo il materiale necessario; il resto verrà tolto nell'head cut successivo
@@ -677,11 +693,7 @@ function BeamExec.ProcessBeams( dRawW, dRawH, dRawL, dOvmHead, dOvmMid, vBeam, b
          -- assegno ordine in lavorazione
          Cnt = Cnt + 1
          EgtSetInfo( nRaw, 'ORD', Cnt)
-         -- creo o pulisco gruppo geometrie aggiuntive
-         if not BL.CreateOrEmptyAddGroup( Pz) then
-            local sOut = 'Error creating Additional Group in Part ' .. tostring( Pz)
-            return false, sOut
-         end
+
          -- aggiungo faccia per taglio iniziale al pezzo
          BL.AddPartStartFace( Pz, b3Solid)
          -- se sovramateriale di testa, lo notifico
@@ -869,6 +881,45 @@ local function ReorderTruncatingCuts( vProc, nPartId)
    return true
 end
 
+-------------------------------------------------------------------------------------------------------------
+-- mi assicuro che vengano rispettate le dipendenze tra le feature
+local function ReorderFeatureWithDependency( vProc)
+   -- si riordina considerando le dipendenze con alcuni limiti:
+   -- * se ci sono dipendenze incrociate il risultato finale non è controllato ( A->B e B->C e C->A)
+   -- * se ci sono dipendenze opposte va in errore ( A->B e B->A)
+
+   -- si sistemano le feature da lavorare prima
+   local i = 1
+   local nMaxIter = ( #vProc * #vProc) + 1
+   local nIter = 0
+   while i <= #vProc do
+      nIter = nIter + 1
+      if nIter > nMaxIter then
+         error( "UNEXPECTED ERROR ON DEPENDENCY")
+      end
+
+      -- si controllano solo i fori
+      if Drill.Identify( vProc[i]) and vProc[i].Dependency and vProc[i].Dependency.ExecBefore and vProc[i].Dependency.ExecBefore.Id then
+         local nRefId = vProc[i].Dependency.ExecBefore.Id
+         local nRefIndex
+
+         for j = 1, #vProc do
+            if i ~= j and vProc[j].Id == nRefId then
+               nRefIndex = j
+               break
+            end
+         end
+
+         -- se il processo deve stare prima, ma ora è dopo
+         if nRefIndex and nRefIndex < i then
+            table.insert( vProc, nRefIndex, table.remove( vProc, i))
+            i = max( nRefIndex - 1, 1)
+         end
+      end
+      i = i + 1
+   end
+end
+
 -------------------------------------------------------------------------------------------------------------
 local function OrderFeatures( vProc, b3Raw, nPartId)
 
@@ -898,6 +949,13 @@ local function OrderFeatures( vProc, b3Raw, nPartId)
       if Hcut.Identify( B2) then
          return false
       end
+      -- se uno dipende dall'altro
+      if B1.Dependency and B1.Dependency.ExecBefore and B1.Dependency.ExecBefore.Id == B2.Id then
+         return true
+      end
+      if B2.Dependency and B2.Dependency.ExecBefore and B2.Dependency.ExecBefore.Id == B1.Id then
+         return false
+      end
       -- se uno di testa e non l'altro, privilegio quello di testa (a meno che non siano dei fori)
       if B1.Head ~= B2.Head  and not Drill.Identify(B1) and not Drill.Identify(B2) then
          return B1.Head
@@ -1191,6 +1249,9 @@ local function OrderFeatures( vProc, b3Raw, nPartId)
    end
 
    ReorderTruncatingCuts( vProc, nPartId)
+
+   -- si riverificano feature con dipendenze
+   ReorderFeatureWithDependency( vProc)
 end
 
 -------------------------------------------------------------------------------------------------------------
@@ -1944,7 +2005,9 @@ local function VerifyDrillMirrored( Proc, vProc, b3Raw)
    -- recupero la lunghezza della parte inclinata della punta
    local dToolDoubleTipLength = EgtTdbGetCurrToolParam( MCH_TP.TOTLEN) - EgtTdbGetCurrToolParam( MCH_TP.LEN)
    -- se foratura splittata, verifico che la distanza minima tra le due punte sia rispettata
-   if abs( Proc.Flg) == 2 and not ( ( ( 2 * dDrillingStep - dToolTipLength - dToolDoubleTipLength) - MIRROR_DRILLINGS_MIN_DISTANCE) > 10 * GEO.EPS_SMALL) then
+   local dTipDistance = 2 * dDrillingStep - dToolTipLength - dToolDoubleTipLength
+   if abs( Proc.Flg) == 2 and not ( ( dTipDistance - MIRROR_DRILLINGS_MIN_DISTANCE) > 10 * GEO.EPS_SMALL) then
+      EgtOutLog( 'Double drilling skipped, tip distance too small ( ' .. dTipDistance .. ' mm) ')
       return
    end
    -- verifico se in doppio
@@ -2033,14 +2096,18 @@ local function SetDrillingsToMachineAfterHeadOrTailCut( vProc, vMachineBeforeInt
          if vDistHead and #vDistHead > 0 then
             -- verifico che il foro sia di testa
             if ( bOpen or ( not bOpen and vtExtr:getX() > 0 and vProc[i].Fcs ~= 0) or ( not bOpen and vtExtr:getX() < 0 and vProc[i].Fce ~= 0)) then
-               vProc[i].MachineAfterHeadCutId = vMachineBeforeIntersectingDrillings.Head.Id
+               if vProc[i].Dependency and vProc[i].Dependency.ExecAfter and vProc[i].Dependency.ExecAfter.Id == vMachineBeforeIntersectingDrillings.Head.Id then
+                  vProc[i].MachineAfterHeadCutId = vMachineBeforeIntersectingDrillings.Head.Id
+               end
                vProc[i].Head = true
             end
          -- se esiste intersezione tra il foro e la feature di coda
          elseif vDistTail and #vDistTail > 0 then
             -- verifico che il foro sia di coda
             if ( bOpen or ( not bOpen and vtExtr:getX() < 0 and vProc[i].Fcs ~= 0) or ( not bOpen and vtExtr:getX() > 0 and vProc[i].Fce ~= 0)) then
-               vProc[i].MachineAfterTailCutId = vMachineBeforeIntersectingDrillings.Tail.Id
+               if vProc[i].Dependency and vProc[i].Dependency.ExecAfter and vProc[i].Dependency.ExecAfter.Id == vMachineBeforeIntersectingDrillings.Tail.Id then
+                  vProc[i].MachineAfterTailCutId = vMachineBeforeIntersectingDrillings.Tail.Id
+               end
                vProc[i].Tail = true
             end
          end
@@ -2048,6 +2115,7 @@ local function SetDrillingsToMachineAfterHeadOrTailCut( vProc, vMachineBeforeInt
    end
 end
 
+
 -------------------------------------------------------------------------------------------------------------
 local function AreDrillingsMirrored( Proc, ProcMirror, b3Raw)
    if Proc.Id == ProcMirror.Id then return false end
@@ -2114,62 +2182,103 @@ end
 
 -------------------------------------------------------------------------------------------------------------
 function GetFeatureInfoAndDependency( vProc, b3Raw, nPartId)
-   -- ciclo tutte le feature
-   for i = 1, #vProc do
-      local Proc = vProc[i]
-      -- calcolo topologia della feature
-      if NeedTopologyFeature( Proc) then
-         Topology.Classify( Proc, b3Raw)
-      -- se non richiesto, setto 'SPECIAL'
-      else
-         Proc.Topology = 'SPECIAL'
-         Proc.TopologyLongName = Proc.Topology
-      end
-      -- controllo la feature con tutte le altre per recuperare le dipendenze
-      for j = 1, #vProc do
-         local ProcB = vProc[j]
-         -- verifico se feature tipo LapJoint è attraversata da almeno un foro
-         if ( Proc.Topology == 'Pocket' or Proc.Topology == 'Tunnel' or Proc.Topology == 'Groove' or Mortise.Identify( Proc)) and Drill.Identify( ProcB) and Overlaps( Proc.Box, ProcB.Box) then
-            -- se foro in coda non setto la dipendenza
-            if not ProcB.AffectedFaces.Left then
-               Proc.PassedByHole = true
-               ProcB.Dependency = {}
-               ProcB.Dependency.ExecBefore = Proc
-            end
+   if vProc and #vProc > 0 and nPartId then
+      -- recupero ID per tagli troncanti testa e coda
+      local nHeadCuttingFeatureId = EgtGetInfo( nPartId, 'HEADCUTFEATUREID', 'i') or 0
+      local nTailCuttingFeatureId = EgtGetInfo( nPartId, 'TAILCUTFEATUREID', 'i') or 0
+      -- ciclo tutte le feature
+      for i = 1, #vProc do
+         local Proc = vProc[i]
+         -- calcolo topologia della feature
+         if NeedTopologyFeature( Proc) then
+            Topology.Classify( Proc, b3Raw)
+         -- se non richiesto, setto 'SPECIAL'
+         else
+            Proc.Topology = 'SPECIAL'
+            Proc.TopologyLongName = Proc.Topology
          end
-         -- verifico se feature tipo LapJoint è attraversata da almeno una mortasa a coda di rondine
-         if ( Proc.Topology == 'Pocket' or Proc.Topology == 'Tunnel' or Proc.Topology == 'Groove') and DtMortise.SideIdentify( ProcB) and Overlaps( Proc.Box, ProcB.Box) then
-            Proc.PassedByDtMortise = true
-         end
-         -- se tenone è attraversato da foro allora il foro deve essere fatto prima
-         if Tenon.Identify( Proc) and Drill.Identify( ProcB) and Overlaps( Proc.Box, ProcB.Box) then
-            Proc.PassedByHole = true
-         end
-         -- verifiche per specchiature
-         if BD.DOWN_HEAD or BD.TWO_EQUAL_HEADS then
-            -- forature
-            if BD.DOUBLE_HEAD_DRILLING and Drill.Identify( Proc) and Drill.Identify( ProcB) and not Proc.Mirror then
-               if AreDrillingsMirrored( Proc, ProcB, b3Raw) then
-                  Proc.Mirror = ProcB
+         -- controllo la feature con tutte le altre per recuperare le dipendenze
+         for j = 1, #vProc do
+            -- non si controlla feature con sé stessa
+            if i ~= j then
+               local ProcB = vProc[j]
+               -- verifico se feature tipo LapJoint è attraversata da almeno un foro
+               if ( Proc.Topology == 'Pocket' or Proc.Topology == 'Tunnel' or Proc.Topology == 'Groove' or Mortise.Identify( Proc)) and Drill.Identify( ProcB) and Overlaps( Proc.Box, ProcB.Box) then
+                  -- se foro in coda non setto la dipendenza
+                  if not ProcB.AffectedFaces.Left then
+                     Proc.PassedByHole = true
+                     ProcB.Dependency = {}
+                     ProcB.Dependency.ExecBefore = Proc
+                  end
+               end
+               -- verifico se feature tipo LapJoint è attraversata da almeno una mortasa a coda di rondine
+               if ( Proc.Topology == 'Pocket' or Proc.Topology == 'Tunnel' or Proc.Topology == 'Groove')
+                  and DtMortise.SideIdentify( ProcB) and Overlaps( Proc.Box, ProcB.Box)  and DtMortise.IsDeeper( ProcB, b3Raw) then
+                  Proc.PassedByDtMortise = true
+               end
+               -- se tenone è attraversato da foro allora il foro deve essere fatto prima
+               if Tenon.Identify( Proc) and Drill.Identify( ProcB) and Overlaps( Proc.Box, ProcB.Box) then
+                  Proc.PassedByHole = true
+               end
+               -- se taglio attraversato da foro, si definisce precedenza in base ad angolo
+               if Drill.Identify( Proc) and Cut.Identify( ProcB) and Overlaps( Proc.Box, ProcB.Box) then
+                  -- recupero e verifico l'entità foro
+                  local DrillAuxId = ( EgtGetInfo( Proc.Id, 'AUXID', 'i') or 0) + Proc.Id
+                  local vtDrillExtr = EgtCurveExtrusion( DrillAuxId, GDB_RT.GLOB)
+                  local bOpen = ( Proc.Fce ~= 0) and ( Proc.Fce ~= Proc.Fcs)
+                  local ptCut, vtCutN = EgtSurfTmFacetCenter( ProcB.Id, 0, GDB_ID.ROOT)
+                  local dMaxAngleDrillOnCut = BD.MAX_ANGLE_DRILL_CUT or 10
+                  if GetAngle( vtDrillExtr, vtCutN) > dMaxAngleDrillOnCut then
+                     if bOpen and GetAngle( -vtDrillExtr, vtCutN) < dMaxAngleDrillOnCut then
+                        ProcB.Dependency = {}
+                        ProcB.Dependency.ExecBefore = Proc
+                        Proc.Dependency = {}
+                        Proc.Dependency.ExecAfter = ProcB
+                     else
+                        Proc.Dependency = {}
+                        Proc.Dependency.ExecBefore = ProcB
+                        ProcB.Dependency = {}
+                        ProcB.Dependency.ExecAfter = Proc
+                     end
+                  else
+                     ProcB.Dependency = {}
+                     ProcB.Dependency.ExecBefore = Proc
+                     Proc.Dependency = {}
+                     Proc.Dependency.ExecAfter = ProcB
+                  end
+               end
+               -- verifiche per specchiature
+               if BD.DOWN_HEAD or BD.TWO_EQUAL_HEADS then
+                  -- forature
+                  if BD.DOUBLE_HEAD_DRILLING and Drill.Identify( Proc) and Drill.Identify( ProcB) and not Proc.Mirror then
+                     if AreDrillingsMirrored( Proc, ProcB, b3Raw) then
+                        Proc.Mirror = ProcB
+                     end
+                  end
+               end
+               -- verifiche per tagli troncanti testa e coda: devono sempre essere subito dopo il taglio di testa e il taglio di coda, rispettivamente
+               if Proc.Prc == 340 and ProcB == nHeadCuttingFeatureId then
+                  Proc.Dependency = {}
+                  Proc.Dependency.ExecBefore = ProcB
+               elseif Proc == nHeadCuttingFeatureId and ProcB.Prc == 340 then
+                  ProcB.Dependency = {}
+                  ProcB.Dependency.ExecBefore = Proc
+               elseif Proc.Prc == 350 and ProcB == nTailCuttingFeatureId then
+                  Proc.Dependency = {}
+                  Proc.Dependency.ExecBefore = ProcB
+               elseif Proc == nTailCuttingFeatureId and ProcB.Prc == 350 then
+                  ProcB.Dependency = {}
+                  ProcB.Dependency.ExecBefore = Proc
+               end
+               -- se una feature deve essere lavorata prima dei tagli troncanti, si setta che non esiste taglio troncante
+               if Proc.Dependency and Proc.Dependency.ExecBefore and Proc.Dependency.ExecBefore.Id == nHeadCuttingFeatureId then
+               --   EgtRemoveInfo( nPartId, 'HEADCUTFEATUREID')
+               end
+               if Proc.Dependency and Proc.Dependency.ExecBefore and Proc.Dependency.ExecBefore.Id == nTailCuttingFeatureId then
+               --   EgtRemoveInfo( nPartId, 'TAILCUTFEATUREID')
                end
             end
          end
-         -- verifiche per tagli troncanti testa e coda: devono sempre essere subito dopo il taglio di testa e il taglio di coda, rispettivamente
-         local nHeadCuttingFeatureId = EgtGetInfo( nPartId, 'HEADCUTFEATUREID', 'i')
-         local nTailCuttingFeatureId = EgtGetInfo( nPartId, 'TAILCUTFEATUREID', 'i')
-         if Proc.Prc == 340 and ProcB == nHeadCuttingFeatureId then
-            Proc.Dependency = {}
-            Proc.Dependency.ExecBefore = ProcB
-         elseif Proc == nHeadCuttingFeatureId and ProcB.Prc == 340 then
-            ProcB.Dependency = {}
-            ProcB.Dependency.ExecBefore = Proc
-         elseif Proc.Prc == 350 and ProcB == nTailCuttingFeatureId then
-            Proc.Dependency = {}
-            Proc.Dependency.ExecBefore = ProcB
-         elseif Proc == nTailCuttingFeatureId and ProcB.Prc == 350 then
-            ProcB.Dependency = {}
-            ProcB.Dependency.ExecBefore = Proc
-         end
       end
    end
 end

LuaLibs/BeamLib.lua

@@ -698,17 +698,19 @@ function BeamLib.GetFaceHvRefDim( nSurfId, nFacet, b3Raw)
    local b3HV = EgtSurfTmGetFacetBBoxRef( nSurfId, nFacet, GDB_BB.STANDARD, frHV)
    local dDimH = b3HV:getDimX()
    local dDimV = b3HV:getDimY()
+
+   -- Si mantiene rettangolo minimo perchè in alcuni casi andava in collisione. Lascio il calcolo in caso si debba ripristinare.
    -- se definito grezzo (o solido), applico eventuali limiti
-   if b3Raw then
-      local dCoeffY = abs( frHV:getVersX():getY())
-      if dCoeffY > GEO.EPS_SMALL then
-         dDimH = min( dDimH, b3Raw:getDimY() / dCoeffY)
-      end
-      local dCoeffZ = abs( frHV:getVersY():getZ())
-      if dCoeffZ > GEO.EPS_SMALL then
-         dDimV = min( dDimV, b3Raw:getDimZ() / dCoeffZ)
-      end
-   end
+   -- if b3Raw then
+   --    local dCoeffY = abs( frHV:getVersX():getY())
+   --    if dCoeffY > GEO.EPS_SMALL then
+   --       dDimH = min( dDimH, b3Raw:getDimY() / dCoeffY)
+   --    end
+   --    local dCoeffZ = abs( frHV:getVersY():getZ())
+   --    if dCoeffZ > GEO.EPS_SMALL then
+   --       dDimV = min( dDimV, b3Raw:getDimZ() / dCoeffZ)
+   --    end
+   -- end
    -- restituisco i valori calcolati
    return frHV, dDimH, dDimV
 end

LuaLibs/DiceCut.lua

@@ -423,7 +423,7 @@ function DiceCut.GetDice( nParent, BBoxRawPart, ptCPlanes, vtNPlanes, bGetOrtoPl
    -- se piani non ortogonali, diminuisco la distanza di offset opportunamente
    local originalOffsetP = OffsetP
    if not bGetOrtoPlanes then
-      local dCoeff = ( vtNPlanes ^ vtNBond):len()
+      local dCoeff = max( ( vtNPlanes ^ vtNBond):len(), 0.5)
       OffsetP = OffsetP * dCoeff
       OffsetO = OffsetO * dCoeff
    end

LuaLibs/FaceByPocket.lua

@@ -30,7 +30,7 @@ local function ApplyPocket( Proc, nSurfId, nFacet, sPocketing, nInd, dMaxElev, v
    -- imposto uso faccia
    EgtSetMachiningParam( MCH_MP.FACEUSE, MCH_MILL_FU.ORTHO_CONT)
    -- imposto note utente
-   local sNotes = ''
+   local sNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
    -- eventuale massima elevazione
    if dMaxElev > 0.1 then
       sNotes = EgtSetValInNotes( sNotes, 'MaxElev', EgtNumToString( dMaxElev, 2))

LuaLibs/FacesBySaw.lua

@@ -596,14 +596,16 @@ function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDw
    EgtSetMachiningGeometry( {{ nSurfId, nFacet}})
    -- imposto uso faccia
    EgtSetMachiningParam( MCH_MP.FACEUSE, nFaceUse)
-   -- vtFaceUse non funziona correttaemnte in caso che il lato da lavorare sia a 45°. Potrebbe ritornare una trilinea, non gestibile. Quindi si setta l'EDGE
+   -- vtFaceUse non funziona correttamente in caso che il lato da lavorare sia a 45°. Potrebbe ritornare una trilinea, non gestibile. Quindi si setta l'EDGE
    local nEdgeFaceUse = GetEdgeToMachineFromVector( nSurfId, nFacet, vtOrthO)
    if nEdgeFaceUse and ( AreSameOrOppositeDirApprox( vtOrthO:getX(), 0.707) or AreSameOrOppositeDirApprox( vtOrthO:getY(), 0.707) or AreSameOrOppositeDirApprox( vtOrthO:getZ(), 0.707)) then
-      local sNoteEdgeFaceUse = 'EdgesFaceUse=' .. EgtNumToString( nEdgeFaceUse)  .. ';'
-      EgtSetMachiningParam( MCH_MP.USERNOTES, sNoteEdgeFaceUse)
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'EdgesFaceUse', EgtNumToString( nEdgeFaceUse))
+      EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
    else
-      local sNoteVtFaceUse = 'VtFaceUse=' .. EgtNumToString( vtOrthO:getX(),3) .. ',' .. EgtNumToString( vtOrthO:getY(),3) .. ',' .. EgtNumToString( vtOrthO:getZ(),3) .. ';'
-      EgtSetMachiningParam( MCH_MP.USERNOTES, sNoteVtFaceUse)
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'VtFaceUse', EgtNumToString( vtOrthO:getX(), 3) .. ',' .. EgtNumToString( vtOrthO:getY(), 3) .. ',' .. EgtNumToString( vtOrthO:getZ(), 3))
+      EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
       -- imposto allungamenti iniziale e finale (in caso si utilizzi EDGE, non serve prolungare o accorciare)
       EgtSetMachiningParam( MCH_MP.STARTADDLEN, dAllStart - dAccStart)
       EgtSetMachiningParam( MCH_MP.ENDADDLEN, dAllEnd - dAccEnd)

LuaLibs/MachiningLib.lua

@@ -139,6 +139,7 @@ end
 ---------------------------------------------------------------------
 function VerifyMill( Machining, dDepth, sTuuidMstr, dMaxDiam, dMaxTotLen, bH2)
    if ( not dDepth or Machining.Tool.MaxMat > dDepth - GEO.EPS_SMALL) and
+      ( Machining.Type ~= 'FloatingAggregate' or abs( Machining.Tool.MaxMat - dDepth) < 100 * GEO.EPS_SMALL) and
       ( not sTuuidMstr or sTuuidMstr == Machining.Tool.UUID) and
       ( not dMaxDiam or Machining.Tool.Diameter < dMaxDiam + GEO.EPS_SMALL) and
       ( not dMaxTotLen or Machining.Tool.TotalLength < dMaxTotLen + GEO.EPS_SMALL) then
@@ -227,7 +228,11 @@ function GetMachinings( MachiningType, sType)
                table.insert( validMachinings, Machining)
                -- se non è tastatura, recupero dati utensile
                if MachiningType ~= MCH_MY.PROBING then
-                  if ( MachiningType == MCH_MY.MILLING) or ( MachiningType == MCH_MY.POCKETING) or ( MachiningType == MCH_MY.DRILLING and EgtStartsWith( sType, 'Pocket')) then
+                  -- caso speciale utensile su aggregato flottante
+                  if MachiningType == MCH_MY.MILLING and sType == 'FloatingAggregate' then
+                     local sNotes = EgtTdbGetCurrToolParam( MCH_TP.USERNOTES)
+                     Machining.Tool.MaxMat = EgtGetValInNotes( sNotes, 'TOOL_OVERHANG', 'd') or -1
+                  elseif ( MachiningType == MCH_MY.MILLING) or ( MachiningType == MCH_MY.POCKETING) or ( MachiningType == MCH_MY.DRILLING and EgtStartsWith( sType, 'Pocket')) then
                      Machining.Tool.MaxMat = EgtTdbGetCurrToolMaxDepth()
                   else
                      Machining.Tool.MaxMat = EgtTdbGetCurrToolParam( MCH_TP.MAXMAT)

LuaLibs/ProcessCut.lua

@@ -65,11 +65,14 @@ function ProcessCut.Classify( Proc, b3Raw)
    end
    -- recupero i dati del taglio
    local ptC, vtN = EgtSurfTmFacetCenter( Proc.Id, 0, GDB_ID.ROOT)
-   if vtN:getZ() <= - 0.5 and abs( vtN:getY()) > 0.1 or ( vtN:getZ() <= - 0.174 and abs( vtN:getY()) > 0.866) then
-      -- calcolo le massime estensioni lineari orizzontale e verticale della faccia
-      local _, DimH, DimV = BL.GetFaceHvRefDim( Proc.Id, 0, b3Raw)
+   -- calcolo le massime estensioni lineari orizzontale e verticale della faccia
+   local _, DimH, DimV = BL.GetFaceHvRefDim( Proc.Id, 0, b3Raw)
+   if ( vtN:getZ() <= - 0.5 and abs( vtN:getY()) > 0.1) or
+      ( vtN:getZ() <= - 0.174 and abs( vtN:getY()) > 0.866) or
+      ( vtN:getZ() <= - 0.174 and abs( vtN:getZ()) * DimV > BD.MAX_DIM_DICE)
+   then
       -- confronto queste estensioni con la massima dimensione del DiceCut (impossibile lavorare se entrambe maggiori)
-      if DimH > BD.MAX_DIM_DICE and DimV > BD.MAX_DIM_DICE then
+      if DimH > BD.MAX_DIM_DICE + 100 * GEO.EPS_SMALL and DimV > BD.MAX_DIM_DICE + 100 * GEO.EPS_SMALL then
          return true, true
       end
    end
@@ -90,7 +93,7 @@ function ProcessCut.Classify( Proc, b3Raw)
          end
       end
       -- calcolo l'ingombro orizzontale della faccia
-      local _, DimH, DimV = BL.GetFaceHvRefDim( Proc.Id, 0)
+      _, DimH, DimV = BL.GetFaceHvRefDim( Proc.Id, 0)
       -- confronto questo ingombro con il doppio della massima dimensione del DiceCut (impossibile lavorare sotto da sopra se più di 2 tagli oppure se tipo PF, taglio inclinato in Y e non taglio singolo orizzontale)
       if DimH > 2 * BD.MAX_DIM_DICE  or ( BD.C_SIMM and ( abs( vtN:getY()) > 0.1) and dMaxMat < DimH + BD.CUT_EXTRA) then
          return true, true
@@ -379,7 +382,9 @@ local function MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, b
    local vCuts = {}
    local dDicingOffsetP
    local dDicingOffsetO
-   if ( ( not Proc.AdvTail) or bForceDicing) and ( dCutH > dMaxDepth - BD.CUT_EXTRA - 3 * BD.COLL_SIC or dCutV > dMaxVertDepth - BD.CUT_EXTRA - 3 * BD.COLL_SIC) then
+   if ( ( not Proc.AdvTail) or bForceDicing) and
+        ( dCutH - 100 * GEO.EPS_SMALL > dMaxDepth - BD.CUT_EXTRA - 3 * BD.COLL_SIC or
+          dCutV - 100 * GEO.EPS_SMALL > dMaxVertDepth - BD.CUT_EXTRA - 3 * BD.COLL_SIC) then
       local ptExtra, vtExtra
       local bAutoCalcSurf = true
       if Proc.AdvTail then

LuaLibs/ProcessDrill.lua

@@ -527,6 +527,17 @@ function ProcessDrill.Make( Proc, nPhase, nRawId, nPartId)
    dMaxDepth = min( dMaxDepth, max( dToolFreeLen - dSubL, 0))
    -- Verifico inclinazione foro nei limiti
    local bTryDrill = EgtIf( dMaxDepth > 0, ( CosB < BD.DRILL_VX_MAX), false)
+   -- se il foro deve essere eseguito dopo un taglio, potrebbe essere perchè il taglio crea una superficie perpendicolare
+   if Proc.Dependency and Proc.Dependency.ExecAfter then
+      local ptCut, vtCutN = EgtSurfTmFacetCenter( Proc.Dependency.ExecAfter.Id, 0, GDB_ID.ROOT)
+      local dMaxAngleDrillOnCut = BD.MAX_ANGLE_DRILL_CUT or 10
+      local dAngle = GetAngle( vtExtr, vtCutN)
+      CosB = cos( dAngle)
+      if dAngle < dMaxAngleDrillOnCut then
+         -- controllo di essere nei limiti
+         bTryDrill = true
+      end
+   end
    if ( CosB > 0.8 * BD.DRILL_VX_MAX and CosB < BD.DRILL_VX_MAX_ANGLEDRILL) then
       -- cerco le forature speciali AngleDrill
       local sDrilling3, sType3, dMaxDepth3 = ML.FindAngleDrilling( dDiam, dCheckDepth, bDrillUp, bDrillDown)
@@ -627,7 +638,8 @@ function ProcessDrill.Make( Proc, nPhase, nRawId, nPartId)
    local dStartPos = max( dMinStartPos, dToolDbStartPos)
    EgtSetMachiningParam( MCH_MP.STARTPOS, dStartPos)
    -- Note utente con dichiarazione nessuna generazione sfridi per Vmill
-   local sUserNotes = EgtSetVal( 'VMRS', 0) .. ';'
+   local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   sUserNotes = EgtSetValInNotes( sUserNotes, 'VMRS', 0)
    -- aggiungo alle note massima elevazione (coincide con affondamento)
    if dMaxElev then
       sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dMaxElev, 1))
@@ -638,16 +650,6 @@ function ProcessDrill.Make( Proc, nPhase, nRawId, nPartId)
    end
    -- se lavorazione in doppio
    if Proc.Double and Proc.Double > 0 then
-      -- calcolo gli step reali
-      local dStep = EgtGetMachiningParam( MCH_MP.STEP)
-      local nNumStep = ceil( dDepth/dStep)
-      local dRealStep = dDepth / nNumStep
-      -- Se foro passante e nel penultimo step le punte si trovano più vicine del minimo ( MinDistX1X2 + Puntina centraggio H1 + puntina centraggio H2) ricalcolo facendo uno step in meno
-      if bOpen and ( nNumStep > 1) and ( ( dLen / 2)  - ( dRealStep * (nNumStep - 1))) * 2 < ( 40 + 10 + 10) then
-         dRealStep = ceil( dDepth / (nNumStep - 1))
-         EgtSetMachiningParam( MCH_MP.STEP, dRealStep)
-         sMyWarn ='Warning in drill-double : step changed to ' .. tostring(dRealStep) .. 'mm'
-      end
       sUserNotes = EgtSetValInNotes( sUserNotes, 'DOUBLE', Proc.Double)
       if Proc.Double ~= Proc.PrevDouble then
          sUserNotes = EgtSetValInNotes( sUserNotes, 'StartZmax', 2)

LuaLibs/ProcessDtMortise.lua

@@ -51,6 +51,23 @@ function ProcessDtMortise.FrontIdentify( Proc)
    return (( Proc.Grp == 3 or Proc.Grp == 4)  and  Proc.Prc == 56)
 end
 
+---------------------------------------------------------------------
+-- Riconoscimento della feature profonda, non sulla faccia della trave
+function ProcessDtMortise.IsDeeper( Proc, b3Raw)
+   -- recupero i dati della curva di contorno della faccia di fondo
+   local AuxId = EgtGetInfo( Proc.Id, 'AUXID', 'i')
+   if not AuxId then return false end
+   AuxId = AuxId + Proc.Id
+   local vtExtr = EgtCurveExtrusion( AuxId, GDB_RT.GLOB)
+   if ( AreSameVectorApprox( vtExtr, -Y_AX()) and Proc.Box:getMin():getY() > b3Raw:getMin():getY() + 100 * GEO.EPS_SMALL) or
+      ( AreSameVectorApprox( vtExtr, Y_AX()) and Proc.Box:getMax():getY() < b3Raw:getMax():getY() - 100 * GEO.EPS_SMALL) or
+      ( AreSameVectorApprox( vtExtr, -Z_AX()) and Proc.Box:getMin():getZ() > b3Raw:getMin():getZ() + 100 * GEO.EPS_SMALL) or
+      ( AreSameVectorApprox( vtExtr, Z_AX()) and Proc.Box:getMax():getZ() < b3Raw:getMax():getZ() - 100 * GEO.EPS_SMALL) then
+      return true
+   end
+   return false
+end
+
 ---------------------------------------------------------------------
 -- Verifica se feature di coda
 function ProcessDtMortise.IsTailFeature( Proc, b3Raw)
@@ -366,11 +383,10 @@ function ProcessDtMortise.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
    -- se con tasca, la lavoro (mai in doppio)
    if bPocket then
       -- recupero il contorno della tasca (seconda curva ausiliaria)
-      local sVal = EgtGetInfo( Proc.Id, 'AUXID')
-      local vsAuxId = EgtSplitString( sVal)
+      local vAuxId = EgtGetInfo( Proc.Id, 'AUXID', 'vi')
       local Aux2Id
-      if vsAuxId and #vsAuxId >=2 then
-         Aux2Id = tonumber( vsAuxId[2])
+      if vAuxId and #vAuxId >=2 then
+         Aux2Id = vAuxId[2]
       end
       if Aux2Id then Aux2Id = Aux2Id + Proc.Id end
       if not Aux2Id  or  ( EgtGetType( Aux2Id) & GDB_FY.GEO_CURVE) == 0 then
@@ -406,7 +422,9 @@ function ProcessDtMortise.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
       -- aggiungo geometria
       EgtSetMachiningGeometry( {{ Aux2Id, -1}})
       -- dichiaro non si generano sfridi per VMill
-      local sUserNotes = 'MaxElev='.. EgtNumToString( dMaxMat - 0.1, 1) .. '; VMRS=0;'
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dMaxMat - 0.1, 1))
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'VMRS', 0)
       EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
       -- eseguo
       if not ML.ApplyMachining( true, false) then
@@ -517,7 +535,9 @@ function ProcessDtMortise.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
                   EgtSetMachiningParam( MCH_MP.SCC, nSCC)
                end
                -- dichiaro non si generano sfridi per VMill
-               local sUserNotes = 'MaxElev='.. EgtNumToString( dAltMort, 1) .. '; VMRS=0;'
+               local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+               sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dAltMort, 1))
+               sUserNotes = EgtSetValInNotes( sUserNotes, 'VMRS', 0)
                -- se lavorazione in doppio
                if Proc.Double and Proc.Double > 0 then
                   sUserNotes = EgtSetValInNotes( sUserNotes, 'DOUBLE', Proc.Double)
@@ -655,7 +675,9 @@ function ProcessDtMortise.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
       if bMultipleZPasses then
          dMaxElev = dVerticalStep
       end
-      local sUserNotes = EgtSetVal( 'MaxElev', EgtNumToString( dMaxElev - 0.1, 1)) .. ';' .. EgtSetVal( 'VMRS', 0) .. ';'
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dMaxElev - 0.1, 1))
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'VMRS', 0)
       -- in presenza di pocket dichiaro che non sto entrando e uscendo nel grezzo
       if bPocket then
          sUserNotes = EgtSetValInNotes( sUserNotes, 'OutRaw', 3)

LuaLibs/ProcessDtTenon.lua

@@ -109,8 +109,9 @@ local function ApplyPocket( Proc, sPocketing, nStep, dSurfStep, nIdSurf, vtExtr)
    -- imposto uso faccia
    EgtSetMachiningParam( MCH_MP.FACEUSE, MCH_MILL_FU.ORTHO_CONT)
    if dSurfStep > 0 then
+      local sNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
       -- imposto elevazione
-      local sNotes = 'MaxElev=' .. EgtNumToString( dSurfStep, 2) .. ';'
+      sNotes = EgtSetValInNotes( sNotes, 'MaxElev', EgtNumToString( dSurfStep, 2))
       EgtSetMachiningParam( MCH_MP.USERNOTES, sNotes)
    end
    -- imposto posizione braccio porta testa
@@ -322,7 +323,8 @@ function ProcessDtTenon.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
       -- sistemo i parametri
       local dOffs = ( i - 1) * dStep
       EgtSetMachiningParam( MCH_MP.OFFSR, dOffs)
-      local sUserNotes = EgtSetVal( 'MaxElev', EgtNumToString( dDtTenH, 1)) .. ';'
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dDtTenH, 1))
       EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
       -- sistemo il lato e la direzione di lavoro
       EgtSetMachiningParam( MCH_MP.WORKSIDE, EgtIf( bCW, MCH_MILL_WS.LEFT, MCH_MILL_WS.RIGHT))
@@ -436,7 +438,8 @@ function ProcessDtTenon.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
             EgtSetMachiningParam( MCH_MP.FACEUSE, nFaceUse)
 
             -- imposto elevazione
-            local sUserNotes = EgtSetVal( 'MaxElev', EgtNumToString( dDtTenH, 1)) .. ';'
+            local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+            sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dDtTenH, 1))
             EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
 
             -- imposto posizione braccio porta testa

LuaLibs/ProcessFreeContour.lua

@@ -897,7 +897,9 @@ local function MakeByPocket( Proc, nPhase, nRawId, nPartId, dOvmHead)
    end
    EgtSetMachiningParam( MCH_MP.DEPTH, dDepth)
    -- imposto elevazione
-   EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( dMaxDepth, 1) .. ';')
+   local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dMaxDepth, 1))
+   EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
    -- imposto eventuale offset radiale, se impostato dall'utente
    local dRadialOffset = EgtGetInfo( Proc.Id, Q_RADIAL_OFFSET, 'd') or 0
    if abs( dRadialOffset) > 10 * GEO.EPS_SMALL then

LuaLibs/ProcessHeadCut.lua

@@ -159,6 +159,105 @@ local function MakeChamfer( nOriId, Proc, nPhase, nRawId, nPartId, dOvmHead)
    return true, nil
 end
 
+---------------------------------------------------------------------
+-- smussi in testa
+local function MakeHeadChamfer( idProc, nPartId)
+   local dDepthHeadChamfer = EgtGetInfo( idProc, 'Q08', 'd') or 0
+   -- se non attivo esco subito
+   if dDepthHeadChamfer < 100 * GEO.EPS_SMALL then
+      return
+   end
+
+   -- recupero gruppo per geometria aggiuntiva
+   local AddGrpId = BL.GetAddGroup( nPartId)
+   if not AddGrpId then
+      local sErr = 'Error on process StartFace impossible to find AddGroup'
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+
+   -- recupero la lavorazione
+   local sMilling = ML.FindMilling( 'Mark')
+   if not sMilling then
+      local sErr = 'Error : milling not found in library'
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+
+   local nLoopId, nLoopCnt = EgtExtractSurfTmFacetLoops( idProc, 0, AddGrpId)
+   if not nLoopId or nLoopCnt > 1 then
+      local sErr = 'Error MakeHeadChamfer : too many loops'
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+
+   -- setto direzione estrusione corretta
+   EgtModifyCurveExtrusion( nLoopId, X_AX())
+   EgtSetGridFrame( Frame3d( 0,0,0, GDB_FR.RIGHT))
+
+   local dQ09Value = EgtGetInfo( idProc, 'Q09', 'd')
+   local bChamferedEdge = dQ09Value > 0
+
+   local nIdFirstEntity, nEntityCnt = EgtExplodeCurveCompo( nLoopId)
+   local p3MidPoint = EgtMP( nIdFirstEntity, GDB_ID.GRID)
+   
+   for i = 0, nEntityCnt - 1 do
+      if EgtCurveLength( nIdFirstEntity + i) - 10 < abs( dQ09Value) * 2 then
+         local sErr = 'Error MakeHeadChamfer : Q09 too high'
+         EgtOutLog( sErr)
+         return false, sErr
+      end
+   end
+
+   -- creo raccordo o fillet
+   for i = 0, nEntityCnt - 1 do
+      local idFirst = nIdFirstEntity + i
+      local idSecond = EgtIf( i == nEntityCnt - 1, nIdFirstEntity, idFirst + 1)
+      local ptEndPointFirst = EgtEP( idFirst, GDB_ID.GRID) - ( abs( dQ09Value) * EgtEV( idFirst, GDB_ID.GRID))
+      local ptStartPointSecond = EgtSP( idSecond, GDB_ID.GRID) + ( abs( dQ09Value) * EgtEV( idSecond, GDB_ID.GRID))
+
+      if bChamferedEdge then
+         EgtCurveChamfer( AddGrpId, idFirst, ptEndPointFirst, idSecond, ptStartPointSecond, abs( dQ09Value), true, GDB_RT.GRID)
+      else
+         EgtCurveFillet( AddGrpId, idFirst, ptEndPointFirst, idSecond, ptStartPointSecond, abs( dQ09Value), true, GDB_RT.GRID)
+      end
+   end
+
+   EgtSelectPathObjs( nIdFirstEntity, true)
+   local idGeom, idGeomCnt = EgtCurveCompoByChain( AddGrpId, GDB_ID.SEL, {0,0,0}, true)
+   if not idGeom or idGeomCnt > 1 then
+      local sErr = 'Error MakeHeadChamfer : too many loops'
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+   EgtChangeClosedCurveStartPoint( idGeom, p3MidPoint, GDB_RT.GRID)
+
+   -- Inserisco la lavorazione del lato standard
+   local dExtra = 2
+   local sName1 = 'HeadCham_' .. ( EgtGetName( idProc) or tostring( idProc))
+   local nMch1Id = EgtAddMachining( sName1, sMilling)
+   if not nMch1Id then
+      local sErr = 'Error adding machining ' .. sName1 .. '-' .. sMilling
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+   -- aggiungo geometria
+   EgtSetMachiningGeometry( {{ idGeom, -1}})
+   -- assegno affondamento e offset radiale
+   EgtSetMachiningParam( MCH_MP.DEPTH, dDepthHeadChamfer + dExtra)
+   EgtSetMachiningParam( MCH_MP.OFFSR, dExtra)
+   -- assegno lato di lavoro
+   EgtSetMachiningParam( MCH_MP.WORKSIDE, MCH_MILL_WS.RIGHT)
+   -- eseguo
+   if not ML.ApplyMachining( true, false) then
+      local _, sErr = EgtGetLastMachMgrError()
+      EgtSetOperationMode( nMch1Id, false)
+      return false, sErr
+   end
+
+   return true, nil
+end
+
 ---------------------------------------------------------------------
 -- tagli verticali aggiuntivi
 local function AddVerticalPreCuts( Proc, sCutting, dCutXOffset, b3Raw, dOffsetBetweenCuts)
@@ -533,6 +632,16 @@ function ProcessHeadCut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, bNeedHCut
    
    local bOk, sErr = MakeStandardCuts( Proc, b3Raw, nCuts, dOffsL, HeadCutType, Cutting1Data, Cutting2Data, nil, dOvmHead)
 
+
+   -- alla fine del taglio si aggiungono gli smussi in testa
+   local _, sErrHeadChamfer = MakeHeadChamfer( nOriId or Proc.Id, nPartId)
+   if sErr then
+      sErr = sErr..'\n'..sErrHeadChamfer
+   else
+      sErr = sErrHeadChamfer
+   end
+
+
    return bOk, sErr
 end
 

LuaLibs/ProcessLongCut.lua

@@ -483,9 +483,10 @@ local function MakeByPocketing( Proc, nPhase, nRawId, nPartId)
       EgtOutLog( sWarn)
    end
    -- imposto elevazione e dichiaro non si generano sfridi per VMill
-   local sNotes = 'MaxElev=' .. EgtNumToString( dFacElev, 1) .. ';'
-   sNotes = sNotes .. 'VMRS=0;'
-   EgtSetMachiningParam( MCH_MP.USERNOTES, sNotes)
+   local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dFacElev, 1))
+   sUserNotes = EgtSetValInNotes( sUserNotes, 'VMRS', 0)
+   EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
    -- eseguo
    if not ML.ApplyMachining( true, false) then
       -- provo ad allargare leggermente la tasca
@@ -1425,8 +1426,9 @@ function ProcessLongCut.Make( Proc, nPhase, nRawId, nPartId, bCustUseBlade, nCus
             EgtSetMachiningParam( MCH_MP.DEPTH, dDepth)
             -- eventuale nota utente per disabilitare controllo ingresso e uscita in grezzo
             if k < nO then
-               local sNotes = 'OutRaw=3;'
-               EgtSetMachiningParam( MCH_MP.USERNOTES, sNotes)
+               local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+               sUserNotes = EgtSetValInNotes( sUserNotes, 'OutRaw', 3)
+               EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
                -- aumento ingresso su spezzoni per evitare collisione durante approccio pezzo
                if bFront then
                   -- se invertito si allunga ingresso su tutti tranne su ultimo

LuaLibs/ProcessLongDoubleCut.lua

@@ -226,9 +226,10 @@ local function MakeByPocketing( Proc, nPhase, nRawId, nPartId, nSide, nFacInd, d
       EgtOutLog( sWarn)
    end
    -- imposto elevazione e dichiaro non si generano sfridi per VMill
-   local sNotes = 'MaxElev=' .. EgtNumToString( dFacElev, 1) .. ';'
-   sNotes = sNotes .. 'VMRS=0;'
-   EgtSetMachiningParam( MCH_MP.USERNOTES, sNotes)
+   local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dFacElev, 1))
+   sUserNotes = EgtSetValInNotes( sUserNotes, 'VMRS', 0)
+   EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
    -- eseguo
    if not ML.ApplyMachining( true, false) then
       -- provo ad allargare leggermente la tasca

LuaLibs/ProcessMortise.lua

@@ -128,8 +128,9 @@ end
       local nFaceUse = BL.GetNearestParalOpposite( vtN)
       EgtSetMachiningParam( MCH_MP.FACEUSE, nFaceUse)
       -- applico il parametro plunge, che setta la lavorazione per affondare solamente, senza lavorare tutto il contorno; 1: solo lato iniziale, 2: solo lato finale, 3: entrambi
-      local sNotes = 'Plunge=3;'
-      EgtSetMachiningParam( MCH_MP.USERNOTES, sNotes)
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'Plunge' , 3)
+      EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
       -- imposto angolo 3° asse rot
       local vtOrtho = BL.GetVersRef( nFaceUse)
       EgtSetMachiningParam( MCH_MP.BLOCKEDAXIS, BL.GetBlockedAxis( sMortising, 'perpendicular'))
@@ -692,7 +693,8 @@ function ProcessMortise.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
       end
    end
    -- imposto elevazione
-   local sUserNotes = 'MaxElev=' .. EgtNumToString( dMorH, 1) .. ';'
+   local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dMorH, 1))
    -- se lavorazione in doppio
    if Proc.Double and Proc.Double > 0 then
       sUserNotes = EgtSetValInNotes( sUserNotes, 'DOUBLE', Proc.Double)
@@ -752,7 +754,9 @@ function ProcessMortise.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
       -- setto profondità
       EgtSetMachiningParam( MCH_MP.DEPTH, -nDepthMin+BD.CUT_EXTRA)
       -- imposto elevazione
-      EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( (-nDepthMin+BD.CUT_EXTRA), 1) .. ';')
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( (-nDepthMin+BD.CUT_EXTRA), 1))
+      EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
       -- eseguo
       if not ML.ApplyMachining( true, false) then
          local _, sErr = EgtGetLastMachMgrError()

LuaLibs/ProcessProfCamb.lua

@@ -506,7 +506,7 @@ function ProcessProfCamb.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
    -- se il chamfer non è esclusivo continuo con le altre lavorazioni
    if nChamfer < 2 then
       -- verifico se necessario lavorare in doppio
-      local bDouble = ( dProfDepth + BD.CUT_EXTRA > dToolMaxDepth)
+      local bDouble = ( dProfDepth + BD.CUT_EXTRA - 100 * GEO.EPS_SMALL > dToolMaxDepth)
       local dDepth = min( dToolMaxDepth, dProfDepth / 2 + BD.MILL_OVERLAP)
       -- se lavorazione da due parti, aggiungo la seconda
       local sMillingDown

LuaLibs/ProcessProfConcave.lua

@@ -453,7 +453,7 @@ function ProcessProfConcave.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          end
       end
       -- verifico se necessario lavorare in doppio
-      local bDouble = ( dProfDepth + BD.CUT_EXTRA > dToolMaxDepth)
+      local bDouble = ( dProfDepth + BD.CUT_EXTRA - 100 * GEO.EPS_SMALL > dToolMaxDepth)
       local dDepth = min( dToolMaxDepth, dProfDepth / 2 + BD.MILL_OVERLAP)
       -- se lavorazione da due parti, aggiungo la seconda
       local sMillingDown
@@ -666,7 +666,9 @@ function ProcessProfConcave.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          else
             EgtSetMachiningParam( MCH_MP.FACEUSE, MCH_MILL_FU.ORTUP_TOP)
             EgtSetMachiningParam( MCH_MP.WORKSIDE, MCH_MILL_WS.LEFT)
-            EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( (dToolMaxDepth/2), 1))
+            local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+            sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( (dToolMaxDepth/2), 1))
+            EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
          end
          EgtSetMachiningParam( MCH_MP.INVERT, false)
          EgtSetMachiningParam( MCH_MP.DEPTH_STR, 'TH')
@@ -716,7 +718,9 @@ function ProcessProfConcave.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          EgtSetMachiningParam( MCH_MP.DEPTH_STR, 'TH')
          EgtSetMachiningParam( MCH_MP.STEP, 0)
          EgtSetMachiningParam( MCH_MP.OFFSR, 0)
-         EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( dWidth, 1))
+         local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+         sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dWidth, 1))
+         EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
          if BD.TURN then
             local nSCC = GetSccForTurn( vtN)
             EgtSetMachiningParam( MCH_MP.SCC, nSCC)

LuaLibs/ProcessProfConvex.lua

@@ -453,7 +453,7 @@ function ProcessProfConvex.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          end
       end
       -- verifico se necessario lavorare in doppio
-      local bDouble = ( dProfDepth + BD.CUT_EXTRA > dToolMaxDepth)
+      local bDouble = ( dProfDepth + BD.CUT_EXTRA - 100 * GEO.EPS_SMALL > dToolMaxDepth)
       local dDepth = min( dToolMaxDepth, dProfDepth / 2 + BD.MILL_OVERLAP)
       -- se lavorazione da due parti, aggiungo la seconda
       local sMillingDown
@@ -666,7 +666,9 @@ function ProcessProfConvex.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          else
             EgtSetMachiningParam( MCH_MP.FACEUSE, MCH_MILL_FU.ORTUP_TOP)
             EgtSetMachiningParam( MCH_MP.WORKSIDE, MCH_MILL_WS.LEFT)
-            EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( (dToolMaxDepth/2), 1))
+            local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+            sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( (dToolMaxDepth/2), 1))
+            EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
          end
          EgtSetMachiningParam( MCH_MP.INVERT, false)
          EgtSetMachiningParam( MCH_MP.DEPTH_STR, 'TH')
@@ -716,7 +718,9 @@ function ProcessProfConvex.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          EgtSetMachiningParam( MCH_MP.DEPTH_STR, 'TH')
          EgtSetMachiningParam( MCH_MP.STEP, 0)
          EgtSetMachiningParam( MCH_MP.OFFSR, 0)
-         EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( dWidth, 1))
+         local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+         sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dWidth, 1))
+         EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
          if BD.TURN then
             local nSCC = GetSccForTurn( vtN)
             EgtSetMachiningParam( MCH_MP.SCC, nSCC)

LuaLibs/ProcessProfFront.lua

@@ -602,7 +602,9 @@ function ProcessProfFront.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          EgtSetMachiningParam( MCH_MP.DEPTH_STR, 'TH')
          EgtSetMachiningParam( MCH_MP.STEP, 0)
          EgtSetMachiningParam( MCH_MP.OFFSR, 0)
-         EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( dWidth, 1))
+         local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+         sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dWidth, 1))
+         EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
          -- imposto tipo uso faccia
          local nFaceUse = MCH_MILL_FU.PARAL_DOWN
          if nSide == -1 then

LuaLibs/ProcessProfHead.lua

@@ -657,7 +657,9 @@ function ProcessProfHead.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
                EgtSetMachiningParam( MCH_MP.DEPTH_STR, 'TH')
                EgtSetMachiningParam( MCH_MP.STEP, 0)
                EgtSetMachiningParam( MCH_MP.OFFSR, 0)
-               EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( dElev, 1))
+               local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+               sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dElev, 1))
+               EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
                -- imposto posizione braccio
                local nSCC = MCH_SCC.ADIR_YM
                if nSide == 0 then
@@ -697,7 +699,9 @@ function ProcessProfHead.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
                EgtSetMachiningParam( MCH_MP.DEPTH_STR, 'TH')
                EgtSetMachiningParam( MCH_MP.STEP, 0)
                EgtSetMachiningParam( MCH_MP.OFFSR, 0)
-               EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( dElev, 1))
+               local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+               sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dElev, 1))
+               EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
                -- imposto posizione braccio
                local nSCC = MCH_SCC.ADIR_YM
                if nSide == 0 then

LuaLibs/ProcessScarfJoint.lua

@@ -578,7 +578,9 @@ function ProcessScarfJoint.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, dOvmTa
       EgtSetMachiningGeometry( {{ Proc.Id, vFaceOrd[2]-1}})
       -- imposto elevazione
       if dDistFaces then
-         EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( dDistFaces, 1) .. ';')
+         local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+         sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dDistFaces, 1))
+         EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
       end
       -- eseguo
       if not ML.ApplyMachining( true, false) then

LuaLibs/ProcessSplit.lua

@@ -167,6 +167,99 @@ local function MakeChamfer( nOriId, Proc, nPhase, nRawId, nPartId, dOvmTail)
    return true, nil
 end
 
+---------------------------------------------------------------------
+-- smussi in coda
+local function MakeTailChamfer( idProc, nPartId, dDepthTailChamfer)
+   -- recupero gruppo per geometria aggiuntiva
+   local AddGrpId = BL.GetAddGroup( nPartId)
+   if not AddGrpId then
+      local sErr = 'Error on process StartFace impossible to find AddGroup'
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+
+   -- recupero la lavorazione
+   local sMilling = ML.FindMilling( 'Mark')
+   if not sMilling then
+      local sErr = 'Error : milling not found in library'
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+
+   local nLoopId, nLoopCnt = EgtExtractSurfTmFacetLoops( idProc, 0, AddGrpId)
+   if not nLoopId or nLoopCnt > 1 then
+      local sErr = 'Error MakeHeadChamfer : too many loops'
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+
+   -- setto direzione estrusione corretta
+   EgtModifyCurveExtrusion( nLoopId, -X_AX())
+   EgtSetGridFrame( Frame3d( 0,0,0, GDB_FR.LEFT))
+
+   local dQ09Value = EgtGetInfo( idProc, 'Q09', 'd')
+   local bChamferedEdge = dQ09Value > 0
+
+   local nIdFirstEntity, nEntityCnt = EgtExplodeCurveCompo( nLoopId)
+   local p3MidPoint = EgtMP( nIdFirstEntity, GDB_ID.GRID)
+   
+   for i = 0, nEntityCnt - 1 do
+      if EgtCurveLength( nIdFirstEntity + i) - 10 < abs( dQ09Value) * 2 then
+         local sErr = 'Error MakeTailChamfer : Q09 too high'
+         EgtOutLog( sErr)
+         return false, sErr
+      end
+   end
+
+   -- creo raccordo o fillet
+   for i = 0, nEntityCnt - 1 do
+      local idFirst = nIdFirstEntity + i
+      local idSecond = EgtIf( i == nEntityCnt - 1, nIdFirstEntity, idFirst + 1)
+      local ptEndPointFirst = EgtEP( idFirst, GDB_ID.GRID) - ( abs( dQ09Value) * EgtEV( idFirst, GDB_ID.GRID))
+      local ptStartPointSecond = EgtSP( idSecond, GDB_ID.GRID) + ( abs( dQ09Value) * EgtEV( idSecond, GDB_ID.GRID))
+
+      if bChamferedEdge then
+         EgtCurveChamfer( AddGrpId, idFirst, ptEndPointFirst, idSecond, ptStartPointSecond, abs( dQ09Value), true, GDB_RT.GRID)
+      else
+         EgtCurveFillet( AddGrpId, idFirst, ptEndPointFirst, idSecond, ptStartPointSecond, abs( dQ09Value), true, GDB_RT.GRID)
+      end
+   end
+
+   EgtSelectPathObjs( nIdFirstEntity, true)
+   local idGeom, idGeomCnt = EgtCurveCompoByChain( AddGrpId, GDB_ID.SEL, {0,0,0}, true)
+   if not idGeom or idGeomCnt > 1 then
+      local sErr = 'Error MakeTailChamfer : too many loops'
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+   EgtChangeClosedCurveStartPoint( idGeom, p3MidPoint, GDB_RT.GRID)
+
+   -- Inserisco la lavorazione del lato standard
+   local dExtra = 2
+   local sName1 = 'TailCham_' .. ( EgtGetName( idProc) or tostring( idProc))
+   local nMch1Id = EgtAddMachining( sName1, sMilling)
+   if not nMch1Id then
+      local sErr = 'Error adding machining ' .. sName1 .. '-' .. sMilling
+      EgtOutLog( sErr)
+      return false, sErr
+   end
+   -- aggiungo geometria
+   EgtSetMachiningGeometry( {{ idGeom, -1}})
+   -- assegno affondamento e offset radiale
+   EgtSetMachiningParam( MCH_MP.DEPTH, dDepthTailChamfer + dExtra)
+   EgtSetMachiningParam( MCH_MP.OFFSR, dExtra)
+   -- assegno lato di lavoro
+   EgtSetMachiningParam( MCH_MP.WORKSIDE, MCH_MILL_WS.RIGHT)
+   -- eseguo
+   if not ML.ApplyMachining( true, false) then
+      local _, sErr = EgtGetLastMachMgrError()
+      EgtSetOperationMode( nMch1Id, false)
+      return false, sErr
+   end
+
+   return true, nil
+end
+
 ---------------------------------------------------------------------
 -- lavorazione con sega a catena per sezioni alte e larghe
 local function MakeCutByChainSaw( nSurfId, sSawing, nFaceUse, dDepth, sNotes, dRadialOffset, bExtendStartEnd, bInvert)
@@ -208,6 +301,10 @@ local function MakeCutByChainSaw( nSurfId, sSawing, nFaceUse, dDepth, sNotes, dR
    local vtN = EgtSurfTmFacetNormVersor( nSurfId, 0, GDB_ID.ROOT)
    local vtOrtho = BL.GetVersRef( nFaceUse)
    EgtSetMachiningParam( MCH_MP.INITANGS, BL.GetChainSawInitAngs( vtN, vtOrtho, 1))
+   -- se il taglio è un precut, sto 10mm più all'interno per essere sicuro di tagliare effettivamente qualcosa
+   if BD.PRECUT_TAIL and sNotes and sNotes:find( 'Precut;') then
+      dRadialOffset = dRadialOffset - 10
+   end
    -- imposto offset radiale per mantenere il materiale in coda per la finitura
    EgtSetMachiningParam( MCH_MP.OFFSR, dRadialOffset)
    -- imposto eventuale allungamento percorso iniziale
@@ -662,7 +759,7 @@ function ProcessSplit.Make( Proc, nPhase, nRawId, nPartId, nOrd, sDownOrSideOrSt
    local dMinTailScrapForAdditionalCuts = 10.123
    local bNeedVerticalAddedCuts = not bSplit and ( Proc.Face[1].WidthTrimmed > BD.MAX_LEN_DICE) and ( dLenEndRaw > dMinTailScrapForAdditionalCuts - 10 * GEO.EPS_SMALL)
    local bNeedHorizontalAddedCuts = not bSplit and not bBigSectionCut and
-                                    ( Proc.Face[1].HeightTrimmed > ( BD.MIN_HEIGHT_ADDED_CUTS or BD.MAX_LEN_DICE)) and
+                                    ( Proc.Face[1].HeightTrimmed > ( BD.MIN_HEIGHT_ADDED_CUTS or BD.MAX_LEN_DICE) + 100 * GEO.EPS_SMALL) and
                                     ( dLenEndRaw > dMinTailScrapForAdditionalCuts - 10 * GEO.EPS_SMALL) and
                                     dOffsL < BD.MAX_DIM_DICE
    -- dati lavorazioni sopra e sotto
@@ -819,6 +916,43 @@ function ProcessSplit.Make( Proc, nPhase, nRawId, nPartId, nOrd, sDownOrSideOrSt
 
    local bOk, sErr = MakeStandardCuts( Proc, b3Raw, nCuts, dOffsL, TailCutType, Cutting1Data, Cutting2Data, nil, dLenEndRaw)
 
+   -- se smussi in coda da aggiungere
+   local dDepthTailChamfer = EgtGetInfo( nOriId or Proc.Id, 'Q08', 'd') or 0
+   if dDepthTailChamfer > 100 * GEO.EPS_SMALL then
+      -- creo subito nuova fase qui, a meno che non sia stata già creata
+      if nNewPhase == 0 then
+         BL.AddPhaseWithRawParts( nRawId, BD.OriXR, BD.PosXR, BD.RAW_OFFSET)
+         nNewPhase = EgtGetCurrPhase()
+         local nDispId = EgtGetPhaseDisposition( nNewPhase)
+         if sDownOrSideOrStd == 'down' then
+            EgtRotateRawPart( nRawId, X_AX(), 180)
+            EgtSetInfo( nDispId, 'TYPE', 'MID2')
+            EgtSetInfo( nDispId, 'ROT', -2)
+         elseif sDownOrSideOrStd == 'side' then
+            if bPreMove then EgtMoveRawPart( nRawId, vtMove) end
+            EgtRotateRawPart( nRawId, X_AX(), EgtIf( BD.RIGHT_LOAD, -90, 90))
+            if not bPreMove then EgtMoveRawPart( nRawId, vtMove) end
+            EgtSetInfo( nDispId, 'TYPE', 'MID2')
+            EgtSetInfo( nDispId, 'ROT', -1)
+         else
+            EgtSetInfo( nDispId, 'TYPE', 'END')
+         end
+         EgtSetInfo( nDispId, 'ORD', nOrd)
+         -- se grezzo successivo senza pezzi e finale, va tolto
+         local nNextRawId = EgtGetNextRawPart( nRawId)
+         if nNextRawId  and  EgtGetPartInRawPartCount( nNextRawId) == 0  and  EgtGetRawPartBBox( nNextRawId):getDimX() < BD.MinRaw then
+            EgtRemoveRawPartFromCurrPhase( nNextRawId)
+         end
+      end
+      -- alla fine del taglio si aggiungono gli smussi in testa
+      local _, sErrHeadChamfer = MakeTailChamfer( nOriId or Proc.Id, nPartId, dDepthTailChamfer)
+      if sErr then
+         sErr = sErr..'\n'..sErrHeadChamfer
+      else
+         sErr = sErrHeadChamfer
+      end
+   end
+
    return bOk, sErr, nNewPhase
 end
 

LuaLibs/ProcessStepJointNotch.lua

@@ -181,8 +181,9 @@ local function MakePocket( Proc, nPartId, ptPs, vtN, nFaceRef, nDiffWidth, sMchF
    -- La tasca ha sempre almeno un lato aperto, imposto opportuno attacco
    EgtSetMachiningParam( MCH_MP.SUBTYPE, MCH_POCK_SUB.SPIRALIN)
    -- imposto elevazione
-   local sNotes = 'MaxElev=' .. EgtNumToString( dElev, 1) .. ';'
-   EgtSetMachiningParam( MCH_MP.USERNOTES, sNotes)
+   local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dElev, 1))
+   EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
    if not ML.ApplyMachining( true, false) then
       -- provo ad allargare leggermente la tasca
       EgtSetMachiningParam( MCH_MP.OFFSR, -0.1)

LuaLibs/ProcessTenon.lua

@@ -236,7 +236,9 @@ function ProcessTenon.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
          -- assegno affondamento e offset radiale
          EgtSetMachiningParam( MCH_MP.DEPTH, -dTenH + dDepth + dExtra)
          EgtSetMachiningParam( MCH_MP.OFFSR, dExtra)
-         EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( dDepth + dExtra, 1) .. ';')
+         local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+         sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dDepth + dExtra, 1))
+         EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
          -- assegno lato di lavoro
          EgtSetMachiningParam( MCH_MP.WORKSIDE, MCH_MILL_WS.RIGHT)
          -- eseguo
@@ -309,7 +311,8 @@ function ProcessTenon.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
       -- aggiungo geometria
       EgtSetMachiningGeometry( {{ AuxId, -1}})
       -- sistemo i parametri
-      local sUserNotes = EgtSetVal( 'MaxElev', EgtNumToString( dTenH - 100 * GEO.EPS_SMALL, 1)) .. ';'
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dTenH - 100 * GEO.EPS_SMALL, 1))
       if i < nPass then sUserNotes = EgtSetValInNotes( sUserNotes, 'OutRaw', 3) end
       EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
       EgtSetMachiningParam( MCH_MP.DEPTH, dDepth)

LuaLibs/ProcessTyroleanDovetail.lua

@@ -451,12 +451,12 @@ local function MakeMillCut( Proc, i, j, k, sMilling, nFacInd, TabNAD, rfFac, dOf
    EgtSetMachiningParam( MCH_MP.STARTADDLEN, ( dToolDiam * 0.75))
    EgtSetMachiningParam( MCH_MP.ENDADDLEN, ( dToolDiam * 0.75))
    -- Note utente con dichiarazione nessuna generazione sfridi per Vmill solo in ultima passata in Z locale
-   local sUserNotes
+   local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
    if i < nStep then
-      sUserNotes = 'MaxElev=' .. EgtNumToString( dStep, 1) .. ';'            
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dStep, 1))
    else
-      sUserNotes = 'VMRS=0;'
-      sUserNotes = sUserNotes .. 'MaxElev=' .. EgtNumToString( dStep, 1) .. ';'
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'VMRS', 0)
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dStep, 1))
    end
    EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
    -- eseguo

LuaLibs/ProcessVariant.lua

@@ -142,7 +142,9 @@ local function MakePocket( Proc, nRawId, b3Raw, nPartId)
       end
       EgtSetMachiningParam( MCH_MP.DEPTH, min( 0, dMaxDepth - vDepth[i]))
       -- imposto elevazione
-      EgtSetMachiningParam( MCH_MP.USERNOTES, 'MaxElev=' .. EgtNumToString( dMaxDepth, 1) .. ';')
+      local sUserNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+      sUserNotes = EgtSetValInNotes( sUserNotes, 'MaxElev', EgtNumToString( dMaxDepth, 1))
+      EgtSetMachiningParam( MCH_MP.USERNOTES, sUserNotes)
       -- eseguo
       if not ML.ApplyMachining( true, false) then
          local _, sErr = EgtGetLastMachMgrError()

UpdateLog.txt

@@ -1,5 +1,24 @@
            ==== Beam Update Log ====
 
+Versione 2.7l3 (23/12/2025)
+- Modif : nei fori che attraversano un taglio si decide la precedenza in base all'angolo tra foro e taglio stesso
+- Fixed : corretto precut in caso di sega a catena
+
+Versione 2.7l2 (16/12/2025)
+- Added : in LapJoint pulizia spigoli con fresa a V su tasche non passanti
+
+Versione 2.7l1 (10/12/2025)
+- Added : in LapJoint aggiunta gestione fresatura con aggregato flottante (Q specifica)
+- Modif : in LapJoint modfifiche alla lavorazione spigoli su faccia frontale o posteriore
+- Modif : in LapJoint lunghe, la spezzatura ora considera se è presente del grezzo dietro
+
+Versione 2.7k1 (25/11/2025)
+- Added : in tagli di testa e coda aggiunti smussi con possibilità di raccordare o smussare spigoli
+- Added : in Lapjoint aggiunto Q14 per settare lavorazione discorde se  longitudinale su faccia sotto 
+- Modif : migliorati i tagli
+- Modif : migliorata lavorazione mortasa a coda di rondine
+- Fixed : in Lapjoint alcune svuotature forzate a spirale
+
 Versione 2.7j2 (30/10/2025)
 - Fixed : in DoubleCut gestito il caso in cui si ha una terza faccia piccola da non lavorare
 

Version.lua

@@ -1,6 +1,6 @@
--- Version.lua by Egaltech s.r.l. 2024/01/30
+-- Version.lua by Egaltech s.r.l. 2026/02/09
 -- Gestione della versione di Beam
 
 NAME = 'Beam'
-VERSION = '2.7j2'
+VERSION = '3.1a1'
 MIN_EXE = '2.7f2'