Cambio versione per rilascio versione ufficiale

- Salita in ZMax dopo una chiodatura avviene solo se l'utensile seguente è diverso da quello attuale (EB1).

Essetre-90480023_XS-MW.mlde

@@ -8,7 +8,8 @@ require( 'EmtGenerator')
 EgtEnableDebug( false)
 if not EmtModifyHeadAuxDirection then error( 'A newer version of the program is required (minimum 2.3j5)') end
 
-PP_VER = '3.1d1_DEV8'
+PP_VER = '3.1d2'
+PP_NVER = '3.1.4.2'
 PP_NVER = '2.7.4.1'
 
 -- Parametri macchina
@@ -34,9 +35,9 @@ MinX2 = 1047.0
 MaxX2 = 6080.0
 MinZ2 = -770.0
 MaxZ2 = 0.0
-SawOffsX = 111.0
+SawOffsX = 110.0
 SawOffsY = 0
-SawOffsZ = -150.25
+SawOffsZ = -150.3
 SawC1Offs = 0
 SawB1Offs = 0
 SawOffs = 0.0
@@ -75,6 +76,7 @@ DeltaTabZ = -1227.6497
 CoeffVM = 0.5
 OffsetH12X = 110
 OffsetH12Z = 150
+ParkYScrapRemove = nil
 
 -- Aggiornamento con dati da TechnoEssetre7
 local sTs3Data = EgtGetStringFromIni( 'Wall', 'DATA_DIR', "C:\\TechnoEssetre7\\EgtData", EgtGetIniFile()).."\\Essetre-90480023_XS-MW.data"
@@ -150,6 +152,7 @@ if EgtExistsFile( sData) then
       if MchOffs.OFFSET_ZERO6_Y then Orig6DeltaX = -MchOffs.OFFSET_ZERO6_Y end
       if MchOffs.OFFSET_ZERO6_X then Orig6DeltaY = MchOffs.OFFSET_ZERO6_X end
       if MchOffs.OFFSET_ZERO6_Z then Orig6DeltaZ = MchOffs.OFFSET_ZERO6_Z end
+      if MchOffs.PARK_Y_SCRAP_REMOVE then ParkYScrapRemove = MchOffs.PARK_Y_SCRAP_REMOVE end
    end
 end
 

Essetre-WALL.NUM.mlpe

@@ -39,7 +39,11 @@ end
 function OnProgramStart()
    -- Info da gruppo BtlInfo
    local BtlInfoId = EgtGetFirstNameInGroup( GDB_ID.ROOT, 'BtlInfo') or GDB_ID.NULL
-   EMT.ORIG = EgtGetInfo( BtlInfoId, 'REFPOS', 'i')  or 1
+   EMT.ORIG = EgtGetInfo( BtlInfoId, 'REFPOS', 'i') or 1
+   -- CASO SPECIALE: questa macchina utilizza origine 3 anche se viene passata origine 1 da TS3
+   if EMT.ORIG == 1 then
+      EMT.ORIG = 3
+   end
    -- Intestazioni
    if not TEST_USE then
       local BtlInfoId = EgtGetFirstNameInGroup( GDB_ID.ROOT, 'BtlInfo') or GDB_ID.NULL
@@ -56,28 +60,7 @@ function OnProgramStart()
    end
    EmtOutput( '('.. MLE_INFO..')')
    -- Parametri macchina
-   local sOut = 'L151='..EgtNumToString( Nail11DeltaY - DeltaTabY, 2)..'\n'..
-                'L152='..EgtNumToString( DeltaTabX - Nail11DeltaX, 2)..'\n'..
-                'L153='..EgtNumToString( DeltaTabZ - Nail11DeltaZ, 2)..'\n'..
-                'L154='..EgtNumToString( Nail12DeltaY - DeltaTabY, 2)..'\n'..
-                'L155='..EgtNumToString( DeltaTabX - Nail12DeltaX, 2)..'\n'..
-                'L156='..EgtNumToString( DeltaTabZ - Nail12DeltaZ, 2)..'\n'..
-                'L157='..EgtNumToString( Nail13DeltaY - DeltaTabY, 2)..'\n'..
-                'L158='..EgtNumToString( DeltaTabX - Nail13DeltaX, 2)..'\n'..
-                'L159='..EgtNumToString( DeltaTabZ - Nail13DeltaZ, 2)..'\n'..
-                'L160='..EgtNumToString( Nail14DeltaY - DeltaTabY, 2)..'\n'..
-                'L161='..EgtNumToString( DeltaTabX - Nail14DeltaX, 2)..'\n'..
-                'L162='..EgtNumToString( DeltaTabZ - Nail14DeltaZ, 2)..'\n'..
-                'L163='..EgtNumToString( Orig2DeltaY, 2)..'\n'..
-                'L164='..EgtNumToString( -Orig2DeltaX, 2)..'\n'..
-                'L165='..EgtNumToString( Orig2DeltaZ, 2)..'\n'..
-                'L166='..EgtNumToString( Orig3DeltaY, 2)..'\n'..
-                'L167='..EgtNumToString( -Orig3DeltaX, 2)..'\n'..
-                'L168='..EgtNumToString( Orig3DeltaZ, 2)..'\n'..
-                'L169='..EgtNumToString( Orig4DeltaY, 2)..'\n'..
-                'L170='..EgtNumToString( -Orig4DeltaX, 2)..'\n'..
-                'L171='..EgtNumToString( Orig4DeltaZ, 2)..'\n'..
-                'G114'..' EA'..EgtNumToString( -DeltaTabY, 2)..' EB'..EgtNumToString( DeltaTabX, 2)..
+   local sOut = 'G114'..' EA'..EgtNumToString( -DeltaTabY, 2)..' EB'..EgtNumToString( DeltaTabX, 2)..
                         ' EC'..EgtNumToString( DeltaTabZ, 2)..' ED'..EgtNumToString( MillOffs, 2)..
                         ' EE'..EgtNumToString( Nail11DeltaY - DeltaTabY, 2, 2)..' EF'..EgtNumToString( DeltaTabX - Nail11DeltaX, 2)..' EG'..EgtNumToString( DeltaTabZ - Nail11DeltaZ, 2)..
                         ' EH'..EgtNumToString( Nail12DeltaY - DeltaTabY, 2, 2)..' EI'..EgtNumToString( DeltaTabX - Nail12DeltaX, 2)..' EL'..EgtNumToString( DeltaTabZ - Nail12DeltaZ, 2)..
@@ -115,7 +98,7 @@ function OnProgramEnd()
    EmtOutput( 'M05 E80000=1')
    -- Tipo di scarico
    if not TEST_USE then
-      EmtOutput( 'M27 E30057=1')
+      EmtOutput( 'M27 E30057=0')
    end
    -- Se modalità test, termino il programma
    if TEST_USE then
@@ -153,10 +136,16 @@ function OnDispositionEnd()
                 ' E30051='..EgtNumToString( 1000 * b3Raw:getDimX(), 0)..
                 ' E30052='..EgtNumToString( 1000 * b3Raw:getDimZ(), 0))
       EMT.ST = b3Raw:getDimZ()
-      -- Scelta origine
-      EmtOutput( 'M26 E30054='..EgtNumToString( EMT.ORIG, 0))
+      
+      -- Comando per gestione carico. Se LOAD90 attivo, bisogna scrivere 4, che significa di attivare il laser posto sul ponte, che cerca lo zero del pannello
+      -- N.B.: si utilizza LOAD90 perchè è un parametro che già leggiamo e che sulle WALL non viene utilizzato
+      local BtlInfoId = EgtGetFirstNameInGroup( GDB_ID.ROOT, 'BtlInfo') or EgtGetCurrMachGroup() or GDB_ID.NULL
+      local nLoad90 = EgtGetInfo( BtlInfoId, 'LOAD90', 'i') or 0
+      if nLoad90 > 0 then nLoad90 = 4 else nLoad90 = 1 end
+      EmtOutput( 'M26 E30054='..EgtNumToString( nLoad90, 0))
       -- Posizione cuffia
-      local dHCuff = b3Raw:getDimZ() + 32 
+      local dHeightSubPiece = EMT.RAWPOS[3] or 0
+      local dHCuff = dHeightSubPiece + b3Raw:getDimZ() + 32 
       EmtOutput( 'E30039=' .. EgtNumToString( dHCuff * 1000, 0))
       -- Eventuale salto a lavorazione in corso
       EmtOutput( 'G79 NE80000')
@@ -248,11 +237,19 @@ end
 function OnPathEnd()
    if IsNailingHead( EMT.HEAD) then
       local dStep = GetValNotes( EgtGetMachiningParam( MCH_MP.USERNOTES), 'Par', 'd') or 100
-      local dSafeZ = max( EgtGetMachiningParam( MCH_MP.STARTPOS), 10) or 20
+      local dSafeZ = EMT.NAIL_START_L3 + ( max( EgtGetMachiningParam( MCH_MP.STARTPOS), 10) or 20)
       --local dSafeZ = EgtMdbGetGeneralParam( MCH_GP.SAFEZ)
       if EMT.HEAD == 'H21' or EMT.HEAD == 'H22' or EMT.HEAD == 'H23' then
+         local nNextOperationId = EgtGetNextActiveOperation( EMT.MCHID)
+         if nNextOperationId then
+            EgtSetCurrMachining( nNextOperationId)
+            EMT.NEXTTOOL = EgtGetMachiningParam( MCH_MP.TOOL)
+            EgtSetCurrMachining( EMT.MCHID)
+         end
+         local sZMax = ''
+         if EMT.TOOL ~= EMT.NEXTTOOL then sZMax = ' EB1' end
          EmtOutput( 'G124 X'..EmtLenToString( EMT.NAIL_START_L1, 3)..' Y'..EmtLenToString( EMT.NAIL_START_L2, 3)..' Z'..EmtLenToString( EMT.NAIL_START_L3, 3)..
-                        ' B'..EmtLenToString( EMT.NAIL_END_L1, 3)..' C'..EmtLenToString( EMT.NAIL_END_L2, 3)..' EA'..EmtLenToString( dStep, 3)..' EB1'..
+                        ' B'..EmtLenToString( EMT.NAIL_END_L1, 3)..' C'..EmtLenToString( EMT.NAIL_END_L2, 3)..' EA'..EmtLenToString( dStep, 3).. sZMax..
                         ' W'..EmtLenToString( dSafeZ, 3)..EMT.NAIL_END)
       else
          local sExtra = ''
@@ -317,7 +314,7 @@ function OnRapid()
             if EMT.SCRAPFIRST then
                EMT.SCRAPFIRST = false
                local b3Raw = EgtGetRawPartBBox( EMT.RAWID)
-               local ParkY = min( -( b3Raw:getMin():getX() - 2000), -MinY)
+               local ParkY = ParkYScrapRemove or min( -( b3Raw:getMin():getX() - 2000), MinY)
                EmtOutput( 'G104 Y' .. EmtLenToString( ParkY, 3) .. ' ET1' .. GetEF())
             end
             -- pre-posizionamento
@@ -329,8 +326,8 @@ function OnRapid()
             local sEE = GetEE()
             local sEF = GetEF()
             local sEM = ' EM'..EgtIf( EMT.S > 0, '3', '4')
-            local sES = ' ES'..EgtNumToString( abs( EMT.S), 0)
-            local sEL = ' EL' .. EmtLenToString( ChSawLen, 3)
+            local sES = ' ES'..EgtNumToString( abs( EMT.S) * EgtIf( EMT.HEAD ~= 'H12', 1, 1.65), 0)
+            local sEL = ' EL' .. GetEL()
             local sER = ' ER' .. EmtLenToString( EMT.TLEN, 3)
             sOut = sOut .. sET .. sEU .. sEE .. sEF .. sEM .. sES .. sEL .. sER
             EmtOutput( sOut)
@@ -341,7 +338,7 @@ function OnRapid()
             EMT.SCRAPFIRST = false
             -- pausa per rimozione sfridi
             local b3Raw = EgtGetRawPartBBox( EMT.RAWID)
-            local ParkY = min( -( b3Raw:getMin():getX() - 2000), -MinY)
+            local ParkY = ParkYScrapRemove or min( -( b3Raw:getMin():getX() - 2000), MinY)
             EmtOutput( 'G104 Y' .. EmtLenToString( ParkY, 3) .. ' ET1' .. GetEF())
          end
       end
@@ -350,11 +347,11 @@ function OnRapid()
       local sOut = 'G101' .. EmtGetAxis( 'L1') .. EmtGetAxis( 'L2') .. EmtGetAxis( 'L3') ..
                              EmtGetAxis( 'R2') .. EmtGetAxis( 'R1')
       if EMT.HEAD == 'H1' or EMT.HEAD == 'H12' or EMT.HEAD == 'H3' or ( EMT.HEAD == 'H14' and not EMT.DOUBLE) then
-         sOut = sOut .. ' U' .. EmtLenToString( MinX2, 3) .. ' W0 V0 A0'
+         sOut = sOut .. ' U' .. EmtLenToString( -MaxX2, 3) .. ' W0 V0 A0'
       elseif EMT.HEAD == 'H14' then
          sOut = sOut .. ' U' .. EmtLenToString( EMT.L2 - EMT.DELTA, 3) .. ' W0 V0 A0'
       elseif EMT.HEAD == 'H2' or EMT.HEAD == 'H21' or EMT.HEAD == 'H22' or EMT.HEAD == 'H23' then
-         sOut = sOut .. ' U' .. EmtLenToString( MaxX1, 3) .. ' W0 V0 A0'
+         sOut = sOut .. ' U' .. EmtLenToString( -MinX1, 3) .. ' W0 V0 A0'
       else
          EmtSetLastError( 1211, "Unknown Head : " .. EMT.HEAD)
       end
@@ -363,8 +360,8 @@ function OnRapid()
       local sEE = GetEE()
       local sEF = GetEF()
       local sEM = ' EM'..EgtIf( EMT.S > 0, '3', '4')
-      local sES = ' ES'..EgtNumToString( abs( EMT.S), 0)
-      local sEL = ' EL' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TLEN, ChSawLen), 3)
+      local sES = ' ES'..EgtNumToString( abs( EMT.S) * EgtIf( EMT.HEAD ~= 'H12', 1, 1.65), 0)
+      local sEL = ' EL' .. GetEL()
       local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
       sOut = sOut .. sET .. sEU .. sEE .. sEF .. sEM .. sES .. sEL .. sER
       EmtOutput( sOut)
@@ -391,8 +388,8 @@ function OnRapid()
          local sEE = GetEE()
          local sEF = ' EF20000'
          local sEM = ' EM'..EgtIf( EMT.S > 0, '3', '4')
-         local sES = ' ES'..EgtNumToString( abs( EMT.S), 0)
-         local sEL = ' EL' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TLEN, ChSawLen), 3)
+         local sES = ' ES'..EgtNumToString( abs( EMT.S) * EgtIf( EMT.HEAD ~= 'H12', 1, 1.65), 0)
+         local sEL = ' EL' .. GetEL()
          local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
          if not IsNailingHead( EMT.HEAD) then
             EmtOutput( 'G102'..EmtGetAxis('L1')..EmtGetAxis('L2')..EmtGetAxis('L3')..EmtGetAxis('R2')..EmtGetAxis('R1')..EMT.IPLGLSTR..sET..sEU..sEE..sEF..sEM..sES..sEL..sER)
@@ -431,17 +428,17 @@ function OnRapid()
          MyAdjustLinearAxes()
          EmtAdjustRotaryAxes()
          -- se fresa o punta su testa 1 raddrizzo l'utensile in risalita
-         if EMT.HEAD == 'H1' and EMT.TCPOS ~= 'T201' and EMT.TCPOS ~= 'T202' and EMT.TCPOS ~= 'T203' then
+         if ( EMT.HEAD == 'H1' or EMT.HEAD == 'H12') and EMT.TCPOS ~= 'T201' and EMT.TCPOS ~= 'T202' and EMT.TCPOS ~= 'T203' then
             local sOut = 'G101' .. EmtGetAxis( 'L1') .. EmtGetAxis( 'L2') .. EmtGetAxis( 'L3') ..
                                    EmtGetAxis( 'R2') .. EmtGetAxis( 'R1') ..
-                                   ' U' .. EmtLenToString( MinX2, 3) .. ' W0 V0 A0'
+                                   ' U' .. EmtLenToString( -MaxX2, 3) .. ' W0 V0 A0'
             local sET = GetET()
             local sEU = GetEU()
             local sEE = GetEE()
             local sEF = GetEF()
             local sEM = ' EM'..EgtIf( EMT.S > 0, '3', '4')
-            local sES = ' ES'..EgtNumToString( abs( EMT.S), 0)
-            local sEL = ' EL' .. EmtLenToString( EMT.TLEN, 3)
+            local sES = ' ES'..EgtNumToString( abs( EMT.S) * EgtIf( EMT.HEAD ~= 'H12', 1, 1.65), 0)
+            local sEL = ' EL' .. GetEL()
             local sER = ' ER' .. EmtLenToString( EMT.TDIAM / 2, 3)
             sOut = sOut .. sET .. sEU .. sEE .. sEF .. sEM .. sES .. sEL .. sER
             EmtOutput( sOut)
@@ -449,19 +446,19 @@ function OnRapid()
          elseif EMT.HEAD == 'H3' then
             local sOut = 'G101' .. EmtGetAxis( 'L1') .. EmtGetAxis( 'L2') .. EmtGetAxis( 'L3') ..
                                    EmtGetAxis( 'R2') .. EmtGetAxis( 'R1') ..
-                                   ' U' .. EmtLenToString( MinX2, 3) .. ' W0 V0 A0'
+                                   ' U' .. EmtLenToString( -MaxX2, 3) .. ' W0 V0 A0'
             local sET = GetET()
             local sEU = GetEU()
             local sEE = GetEE()
             local sEF = GetEF()
             local sEM = ' EM'..EgtIf( EMT.S > 0, '3', '4')
-            local sES = ' ES'..EgtNumToString( abs( EMT.S), 0)
-            local sEL = ' EL' .. EmtLenToString( EMT.TLEN, 3)
+            local sES = ' ES'..EgtNumToString( abs( EMT.S) * EgtIf( EMT.HEAD ~= 'H12', 1, 1.65), 0)
+            local sEL = ' EL' .. GetEL()
             local sER = ' ER' .. EmtLenToString( EMT.TDIAM / 2, 3)
             sOut = sOut .. sET .. sEU .. sEE .. sEF .. sEM .. sES .. sEL .. sER
             EmtOutput( sOut)
             sOut = 'G101' .. ' X' .. EmtLenToString( ( MinX1 + MaxX1) / 2, 3)..
-                   ' U' .. EmtLenToString( MinX2, 3) .. ' W0 V0 A0'
+                   ' U' .. EmtLenToString( -MaxX2, 3) .. ' W0 V0 A0'
             EmtOutput( sOut)
          end
          -- dichiarazione risalita a Zmax
@@ -509,8 +506,8 @@ function OnLinear()
       local sEE = GetEE()
       local sEF = ' EF20000'
       local sEM = ' EM'..EgtIf( EMT.S > 0, '3', '4')
-      local sES = ' ES'..EgtNumToString( abs( EMT.S), 0)
-      local sEL = ' EL' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TLEN, ChSawLen), 3)
+      local sES = ' ES'..EgtNumToString( abs( EMT.S) * EgtIf( EMT.HEAD ~= 'H12', 1, 1.65), 0)
+      local sEL = ' EL' .. GetEL()
       local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
       if not IsNailingHead( EMT.HEAD) then
          EmtOutput( 'G102'..EmtGetAxis('L1')..EmtGetAxis('L2')..EmtGetAxis('L3')..EmtGetAxis('R2')..EmtGetAxis('R1')..EMT.IPLGLSTR..sET..sEU..sEE..sEF..sEM..sES..sEL..sER)
@@ -674,44 +671,47 @@ function CalcInterpPlane()
    if EMT.HEAD == 'H1' or EMT.HEAD == 'H12' or EMT.HEAD == 'H3' then
       EMT.IPLGLFR = Frame3d( ptS, vtE)
    else
-      EMT.IPLGLFR = Frame3d( ptS, Y_AX(), -X_AX(), Z_AX())
+      EMT.IPLGLFR = Frame3d( ptS, -Y_AX(), X_AX(), Z_AX())
    end
    --EmtOutput( 'IPLGLFR='..tostring(EMT.IPLGLFR))
    local _, dAngV, dAngO = SphericalFromVector( vtE)
    local dAngO2 = EmtGetAngO2( EMT.IPLGLFR:getVersZ(), EMT.IPLGLFR:getVersX(), dAngV, dAngO)
-   dAngO = dAngO - 90
-   while dAngO < 0 do
+   dAngO = dAngO + 90
+   while dAngO - GEO.EPS_ANG_SMALL < 0 do
       dAngO = dAngO + 360
    end
+   while dAngO + GEO.EPS_ANG_SMALL > 360 do
+      dAngO = dAngO - 360
+   end
    -- se rotazione solo attorno alla C allora si mette come rotazione finale
    if abs( dAngV) < GEO.EPS_ANG_SMALL then
       dAngO2 = dAngO2 + dAngO
       while dAngO2 >= 360 do
          dAngO2 = dAngO2 - 360
       end
-      dAngO = 0 
+      dAngO = 0
    end
-   local xOut = yS - DeltaTabY
-   local yOut = - ( xS - DeltaTabX - DimTabX)
+   
+   local xOut = - ( yS - DeltaTabY)
+   local yOut = xS - DeltaTabX - DimTabX
    local zOut = zS
    if EMT.ORIG == 2 then
-      xOut = yS - DeltaTabY
-      yOut = - ( xS - DeltaTabX)
+      xOut = - ( yS - DeltaTabY - DimTabY)
+      yOut =  xS - DeltaTabX - DimTabX
    elseif EMT.ORIG == 3 then
-      xOut = yS - DeltaTabY
-      yOut = - ( xS - DeltaTabX - DimTabX)
+      xOut = - ( yS - DeltaTabY)
+      yOut = xS - DeltaTabX
    elseif EMT.ORIG == 4 then
-      xOut = yS - DeltaTabY - DimTabY
-      yOut = - ( xS - DeltaTabX - DimTabX)
-   elseif EMT.ORIG == 5 then
-      xOut = yS - DeltaTabY - DimTabY
-      yOut = - ( xS - DeltaTabX - Orig5DeltaX)
-   elseif EMT.ORIG == 6 then
-      xOut = yS - DeltaTabY
-      yOut = - ( xS - DeltaTabX - Orig5DeltaX)
+      xOut = - ( yS - DeltaTabY - DimTabY)
+      yOut = xS - DeltaTabX
+   end
+
+   if IsNailingHead( EMT.HEAD) then
+      EMT.IPLGLSTR = ' EX'..EmtLenToString( xOut)..' EY'..EmtLenToString( yOut)..' EZ'..EmtLenToString( zOut)
+   else
+      EMT.IPLGLSTR = ' EX'..EmtLenToString( xOut)..' EY'..EmtLenToString( yOut)..' EZ'..EmtLenToString( zOut)..
+                     ' EA0'..' EB'..EgtNumToString( dAngV)..' EC'..EgtNumToString( dAngO)..' ED'..EgtNumToString( dAngO2)
    end
-   EMT.IPLGLSTR = ' EX'..EmtLenToString( xOut)..' EY'..EmtLenToString( yOut)..' EZ'..EmtLenToString( zOut)..
-                  ' EA0'..' EB'..EgtNumToString( dAngV)..' EC'..EgtNumToString( dAngO)..' ED'..EgtNumToString( dAngO2)
    EMT.IPLGL = true
 end
 
@@ -767,6 +767,18 @@ function GetEF()
    return ' EF60000'
 end
 
+
+---------------------------------------------------------------------
+function GetEL()
+   local dToolLen = EMT.TLEN
+   if EMT.HEAD == 'H12' then
+      dToolLen = dToolLen - SawOffsZ
+   elseif EMT.HEAD == 'H3' then
+      dToolLen = ChSawLen
+   end
+   return EgtNumToString( dToolLen, 3)
+end
+
 ---------------------------------------------------------------------
 function EmitCount()
    EMT.CNT = EMT.CNT + 1

Wall/WallData.lua

@@ -28,12 +28,12 @@ local WallData = {
    MILL_OVERLAP = 5,                        -- sovrapposizione tra due mezze fresature
    MAX_CLEAN_CRN30 = 60,                    -- massimo spessore per pulitura angolo con fresa 30deg
    MAX_CLEAN_CRN60 = 150,                   -- massimo spessore per pulitura angolo con fresa 60deg
-   MILL_MAX_DEPTH_AS_MAT = true,            -- massimo affondamento frese uguale ad altezza tagliente (max materiale)
-   T14_T12_DOUBLE = true,                   -- abilita chiodatura in doppio con teste T14 e T12
+   MILL_MAX_DEPTH_AS_MAT = false,            -- massimo affondamento frese uguale ad altezza tagliente (max materiale)
    RAWCOL = { 255, 160, 32, 30},            -- colore del grezzo
-   SIMUL_VIEW_DIR = 3,                      -- direzione di vista predefinita per la simulazione (1=NW, 2=SW, 3=NE, 4=SE)
-   ORIG_CORNER = 'BL',                      -- posizione origine (TL,BL,TR,BR,TM,BM)
-   MID_REF = 27000,                         -- posizione X dell'origine intermedia 
+   DEFAULT_RAW_NO_EXTRA_WIDTH = true,
+   SIMUL_VIEW_DIR = 4,                      -- direzione di vista predefinita per la simulazione (1=NW, 2=SW, 3=NE, 4=SE)
+   ORIG_CORNER = 'BL',                      -- posizione origine (TL,BL,TR,BR,TM,BM) 
+   RAWPART_ROT = 180,
    USE_POSY = true                          -- utilizzare POSY di BTL (spostamento sullo spessore per pareti a layer)
 }