- In STR0005 e STR0012 aggiunta lunghezza sotto la quale cubettare in caso di configurazuione AUTO

- Aggiunta topologia VGroove-2-Through
- Aggiunti messaggi
- In lettura parametri, se il default è nil, ma da json è settato, allora si prende il valore del json

LuaLibs/BeamLib.lua

@@ -764,7 +764,7 @@ function BeamLib.LoadCustomParametersInStrategy( Proc, Part, CustomParameters, D
          if DefaultStrategyParamList.ParameterList[i].sType == 'b' then
             UpdatedParameters[DefaultStrategyParamList.ParameterList[i].sName] = xParameterValue == 'true' or xParameterValue == '1' or xParameterValue == true
          elseif DefaultStrategyParamList.ParameterList[i].sType == 'd' then
-            if #DefaultStrategyParamList.ParameterList[i].sValue > 0 then
+            if #DefaultStrategyParamList.ParameterList[i].sValue > 0 or #xParameterValue > 0 then
                UpdatedParameters[DefaultStrategyParamList.ParameterList[i].sName] = tonumber( xParameterValue)
             -- stringa vuota equivale a non passare alcun valore (deciderà la strategia)
             else

LuaLibs/MachiningLib.lua

@@ -209,6 +209,9 @@ function MachiningLib.GetSplitMachinings( Machinings, SplittingPoints, Part)
             Machinings[nCurrentMachiningIndex].nFeatureSegment = j
             Machinings[nCurrentMachiningIndex].dLengthToMachine = Machinings[nCurrentMachiningIndex].dEdgeLength + Machinings[nCurrentMachiningIndex].LeadIn.dStartAddLength + Machinings[nCurrentMachiningIndex].LeadOut.dEndAddLength
             Machinings[nCurrentMachiningIndex].dTimeToMachine = MachiningLib.GetTimeToMachineAllStepsWithLeadInOut( Machinings[nCurrentMachiningIndex], Part)
+            Machinings[nCurrentMachiningIndex].bIsFirstSegment = ( j == 1)
+            Machinings[nCurrentMachiningIndex].bIsLastSegment = ( j == nParts)
+            Machinings[nCurrentMachiningIndex].bIsMachiningSplitted = true
          end
       -- anche le lavorazioni non splittate necessitano del segmento assegnato
       else

Messages/EgalTechEng.txt

@@ -319,4 +319,8 @@
 1000316=Autocam will apply a machining on the theoretical zero, to avoid collision if the theoretical piece length doesn't correspond to the real length
 1000317=Finish with mill
 1000318=Use a mill to finish the surface if split with chain saw
+1000319=Allow multiple short strips
+1000320=Allow multiple short strips
+1000321=Length limit to drop the waste
+1000322=If Cutting Strategy is set on AUTO, up to this length the software drop the waste, otherwise it'll keep attached
 // ----- End -----

Messages/EgalTechIta.txt

@@ -319,4 +319,8 @@
 1000316=Autocam applicherà una lavorazione sullo zero teorico per evitare collisioni se la lunghezza teorica del pezzo non corrisponde alla lunghezza reale
 1000317=Finisci con la fresa
 1000318=Utilizza una fresa per rifinire la superficie se tagliata con la sega a catena
+1000319=Permettere codoli multipli
+1000320=Permettere codoli multipli
+1000321=Lunghezza limite fino alla quale lo scarto viene staccato
+1000322=Se la strategia di taglio è impostata su AUTO, fino a questa lunghezza il software stacca gli scarti, altrimenti li mantiene attaccati
 // ----- End -----

Messages/EgalTechNld.txt

@@ -319,4 +319,8 @@
 1000316=Autocam past een bewerking toe op het theoretische nulpunt om botsingen te voorkomen als de theoretische lengte niet overeenkomt met de werkelijke lengte
 1000317=Afwerken met frees
 1000318=Gebruik een frees om het oppervlak na te bewerken als dit met de kettingzaag is gespleten
+1000319=Sta meerdere korte verbindingsstrips toe
+1000320=Sta meerdere korte verbindingsstrips toe
+1000321=Maximale lengte voor het uitwerpen van het reststuk
+1000322=Als de snijstrategie op AUTO staat, wordt het reststuk tot deze maximale lengte automatisch uitgeworpen; bij grotere lengtes blijft het reststuk aan het werkstuk bevestigd.
 // ----- End -----

Strategies/AvailableStrategyList.json

@@ -108,6 +108,10 @@
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
          {  "sName": "Cut-1-Through",
             "sImage": "ConfigStrategy\\Cut-1-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" } ]
@@ -151,6 +155,10 @@
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
          {  "sName": "Cut-1-Through",
             "sImage": "ConfigStrategy\\Cut-1-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" } ]
@@ -196,6 +204,10 @@
          {  "sName": "Rabbet-2-Through",
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          }
       ]
    },
@@ -224,6 +236,10 @@
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
          {  "sName": "Cut-1-Through",
             "sImage": "ConfigStrategy\\Cut-1-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" } ]
@@ -271,6 +287,10 @@
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
          {  "sName": "Cut-1-Through",
             "sImage": "ConfigStrategy\\Cut-1-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" } ]
@@ -314,6 +334,10 @@
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
          {  "sName": "Cut-1-Through",
             "sImage": "ConfigStrategy\\Cut-1-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" } ]
@@ -368,6 +392,10 @@
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
          {  "sName": "Cut-1-Through",
             "sImage": "ConfigStrategy\\Cut-1-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" } ]
@@ -455,6 +483,10 @@
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
          {  "sName": "Cut-1-Through",
             "sImage": "ConfigStrategy\\Cut-1-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" } ]
@@ -520,6 +552,10 @@
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
          {  "sName": "Cut-1-Through",
             "sImage": "ConfigStrategy\\Cut-1-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" } ]
@@ -575,6 +611,10 @@
             "sImage": "ConfigStrategy\\Rabbet-2-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
          },
+         {  "sName": "VGroove-2-Through",
+            "sImage": "ConfigStrategy\\VGroove-2-Through.png",
+            "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" }, { "sStrategyId": "STR0010"} ]
+         },
          {  "sName": "Cut-1-Through",
             "sImage": "ConfigStrategy\\Cut-1-Through.png",
             "StrategyList" : [ { "sStrategyId": "STR0002" }, { "sStrategyId": "STR0005" } ]

Strategies/Standard/STR0005/STR0005.json

@@ -100,6 +100,18 @@
             }
          ]
       },
+      {
+         "sName": "dLengthLimitToDropWaste",
+         "sNameNge": "LEN_DROP_WASTE",
+         "sValue": "",
+         "sDescriptionShort": "Length limit to drop the waste",
+         "sDescriptionLong": "If Cutting Strategy is set on AUTO, up to this length the software drop the waste, otherwise it'll keep attached",
+         "idDescriptionShortMsg": 1000321,
+         "idDescriptionLongMsg": 1000322,
+         "sType": "d",
+         "sMessageId": " ",
+         "sMinUserLevel": "1"
+      },
       {
          "sName": "bDisableDicing",
          "sNameNge": "DISABLE_DICING",
@@ -136,6 +148,18 @@
          "sMessageId": " ",
          "sMinUserLevel": "1"
       },
+      {
+         "sName": "bAllowPerpendicularStrip",
+         "sNameNge": "ALLOW_PERPENDICULAR_STRIP",
+         "sValue": "false",
+         "sDescriptionShort": "Allow multiple short strips",
+         "sDescriptionLong": "Allow multiple short strips",
+         "idDescriptionShortMsg": 1000319,
+         "idDescriptionLongMsg": 1000320,
+         "sType": "b",
+         "sMessageId": " ",
+         "sMinUserLevel": "1"
+      },
       {
          "sName": "bFinishWithMill",
          "sNameNge": "ALLOW_FINISH_MILL",

Strategies/Standard/STR0005/STR0005.lua

@@ -100,8 +100,8 @@ function STR0005.Make( bAddMachining, Proc, Part, CustomParameters)
    -- considerazioni necessarie a determinare se lavorare con codolo oppure no
    local bKeepWasteAttached = ( Strategy.Parameters.sCuttingStrategy == 'KEEP_WASTE_ATTACHED')
    local bDropWaste = ( Strategy.Parameters.sCuttingStrategy == 'DROP_WASTE')
-
    local bFeatureHindersClamping = MachiningLib.IsFeatureHinderingClamping( Proc, Part)
+   local dLengthLimitToDropWaste = Strategy.Parameters.dLengthLimitToDropWaste
 
    local bIsFeatureLong = FeatureLib.IsMachiningLong( Proc.b3Box:getDimX(), Part, { dMaxSegmentLength = BeamData.LONGCUT_ENDLEN})
    local bIsTwoFacesCommonEdgeTooLong = ( ( Proc.Topology and ( Proc.Topology.sName == 'Rabbet-2-Through' or Proc.Topology.sName == 'Bevel-2-Blind')) and IsTwoFacesCommonEdgeTooLong( Proc, Part))
@@ -109,10 +109,16 @@ function STR0005.Make( bAddMachining, Proc, Part, CustomParameters)
    -- lavorazione con codolo
    if ( Proc.nFct > 2 and bIsFeatureLong)
       or ( bFeatureHindersClamping and not bDropWaste)
+      or ( dLengthLimitToDropWaste and Proc.b3Box:getDimX() > dLengthLimitToDropWaste)
       or bKeepWasteAttached then
 
       local BladeKeepWasteResult
-      local OptionalParameters = { dExtendAfterTail = dExtendAfterTail, dStripWidth = Strategy.Parameters.dStripWidth, bForced = bKeepWasteAttached}
+      local OptionalParameters = { dExtendAfterTail = dExtendAfterTail,
+                                   dStripWidth = Strategy.Parameters.dStripWidth,
+                                   bAllowPerpendicularStrip = Strategy.Parameters.bAllowPerpendicularStrip,
+                                   bFinishWithMill = Strategy.Parameters.bFinishWithMill,
+                                   bForced = bKeepWasteAttached
+                                 }
       AuxiliaryData.bIgnoreNotClampableLength = true
       Blade.Result, BladeKeepWasteResult = BladeKeepWaste.Make( Proc, Part, OptionalParameters)
       dTimeToMachine = BladeKeepWasteResult.dTimeToMachine

Strategies/Standard/STR0012/STR0012.json

@@ -51,6 +51,18 @@
             }
          ]
       },
+      {
+         "sName": "dLengthLimitToDropWaste",
+         "sNameNge": "LEN_DROP_WASTE",
+         "sValue": "",
+         "sDescriptionShort": "Length limit to drop the waste",
+         "sDescriptionLong": "If Cutting Strategy is set on AUTO, up to this length the software drop the waste, otherwise it'll keep attached",
+         "idDescriptionShortMsg": 1000321,
+         "idDescriptionLongMsg": 1000322,
+         "sType": "d",
+         "sMessageId": " ",
+         "sMinUserLevel": "1"
+      },
       {
          "sName": "sCanDamageNextPiece",
          "sNameNge": "DAMAGE_NEXT_PIECE",
@@ -125,6 +137,30 @@
             }
          ]
       },
+      {
+         "sName": "dStripWidth",
+         "sNameNge": "STRIP_WIDTH",
+         "sValue": "5",
+         "sDescriptionShort": "Strip width",
+         "sDescriptionLong": "In case the waste is still kept attached, this is the wigth dimension of the strip",
+         "idDescriptionShortMsg": 1000129,
+         "idDescriptionLongMsg": 1000130,
+         "sType": "d",
+         "sMessageId": " ",
+         "sMinUserLevel": "1"
+      },
+      {
+         "sName": "bAllowPerpendicularStrip",
+         "sNameNge": "ALLOW_PERPENDICULAR_STRIP",
+         "sValue": "false",
+         "sDescriptionShort": "Allow multiple short strips",
+         "sDescriptionLong": "Allow multiple short strips",
+         "idDescriptionShortMsg": 1000319,
+         "idDescriptionLongMsg": 1000320,
+         "sType": "b",
+         "sMessageId": " ",
+         "sMinUserLevel": "1"
+      },
       {
          "sName": "dMaxWasteLength",
          "sSource": "GEN_dMaxWasteLength",

Strategies/Standard/STR0012/STR0012.lua

@@ -95,13 +95,17 @@ function STR0012.Make( bAddMachining, Proc, Part, CustomParameters)
    local bKeepWasteAttached = ( Strategy.Parameters.sCuttingStrategy == 'KEEP_WASTE_ATTACHED')
    local bDropWaste = ( Strategy.Parameters.sCuttingStrategy == 'DROP_WASTE')
    local bFeatureHindersClamping = MachiningLib.IsFeatureHinderingClamping( NewProc, Part)
+   local dLengthLimitToDropWaste = Strategy.Parameters.dLengthLimitToDropWaste
 
    -- lavorazione con codolo
    if ( bFeatureHindersClamping and not bDropWaste)
+      or ( dLengthLimitToDropWaste and Proc.b3Box:getDimX() > dLengthLimitToDropWaste)
       or bKeepWasteAttached then
 
       local BladeKeepWasteResult
-      local OptionalParameters = { dExtendAfterTail = dExtendAfterTail, dStripWidth = 5, bFinishWithMill = false}
+      local OptionalParameters = { bAllowPerpendicularStrip = Strategy.Parameters.bAllowPerpendicularStrip,
+                                   dStripWidth = Strategy.Parameters.dStripWidth,
+                                   dExtendAfterTail = dExtendAfterTail, bFinishWithMill = false}
       AuxiliaryData.bIgnoreNotClampableLength = true
       TwoFaces.Result, BladeKeepWasteResult = BladeKeepWaste.Make( NewProc, Part, OptionalParameters)
       dTimeToMachine = BladeKeepWasteResult.dTimeToMachine
@@ -113,10 +117,10 @@ function STR0012.Make( bAddMachining, Proc, Part, CustomParameters)
    else
       local BladeToWasteResult
       local OptionalParameters = { dMaxWasteVolume = Strategy.Parameters.dMaxWasteVolume,
-                                 dMaxWasteLength = Strategy.Parameters.dMaxWasteLength,
-                                 bSaveAddedGeometries = bAddMachining,
-                                 dExtendAfterTail = dExtendAfterTail,
-                                 bReduceBladePath = Strategy.Parameters.bReduceBladePath
+                                   dMaxWasteLength = Strategy.Parameters.dMaxWasteLength,
+                                   bSaveAddedGeometries = bAddMachining,
+                                   dExtendAfterTail = dExtendAfterTail,
+                                   bReduceBladePath = Strategy.Parameters.bReduceBladePath
                                  }
       AuxiliaryData.bIgnoreNotClampableLength = false
       TwoFaces.Result, BladeToWasteResult = BladeToWaste.Make( NewProc, Part, OptionalParameters)

StrategyLibs/BLADEKEEPWASTE.lua

@@ -146,10 +146,12 @@ local function MakeBottomFace( Proc, Part, BottomFace, EdgeToMachine, Parameters
    local dExtendAfterTail = Parameters.dExtendAfterTail
    local nToolIndex = Parameters.nToolIndex
    local dStripWidth = Parameters.dStripWidth
+   local bAllowPerpendicularStrip = Parameters.bAllowPerpendicularStrip
    local OtherBottomFace = Parameters.OtherBottomFace
 
    local dDepthToMachine = EdgeToMachine.dElevation / 2 - dStripWidth / 2
-   local OptionalParametersFaceByBlade1 = { dDepthToMachine = dDepthToMachine, bIsSplitFeature = bIsSplitFeature, dExtendAfterTail = dExtendAfterTail, nToolIndex = nToolIndex}
+   local OptionalParametersFaceByBlade1 = { dDepthToMachine = dDepthToMachine, bIsSplitFeature = bIsSplitFeature,
+                                            dExtendAfterTail = dExtendAfterTail, nToolIndex = nToolIndex}
    local EdgeToMachineOpposite = BeamLib.FindEdgeBestOrientedAsDirection( BottomFace.Edges, -EdgeToMachine.vtN)
 
    -- primo lato
@@ -175,8 +177,15 @@ local function MakeBottomFace( Proc, Part, BottomFace, EdgeToMachine, Parameters
       if OtherBottomFace and ( EdgeToMachine.idAdjacentFace == OtherBottomFace.id) then
          dStripWidth = TOOLS[Cutting2.nToolIndex].dThickness + 2 * dStripWidth
       end
-      dDepthToMachine = min( TOOLS[Cutting2.nToolIndex].dMaxMaterial, EdgeToMachine.dElevation - dStripWidth)
+      -- se richiesto, si calcola il codolo verticale
+      if bAllowPerpendicularStrip and FeatureLib.IsMachiningLong( Cutting1.dEdgeLength, Part) then
+         dDepthToMachine = TOOLS[Cutting2.nToolIndex].dMaxMaterial - 10
+      else
+         dDepthToMachine = min( TOOLS[Cutting2.nToolIndex].dMaxMaterial, EdgeToMachine.dElevation - dStripWidth)
+      end
+
       OptionalParametersFaceByBlade2.dDepthToMachine = dDepthToMachine
+      OptionalParametersFaceByBlade2.bAllowPerpendicularStrip = bAllowPerpendicularStrip
 
       Cutting2 = FaceByBlade.Make( Proc, Part, BottomFace, EdgeToMachine, OptionalParametersFaceByBlade2)
       Cutting2.nInternalSortingPriority = 2
@@ -189,8 +198,15 @@ local function MakeBottomFace( Proc, Part, BottomFace, EdgeToMachine, Parameters
       if OtherBottomFace and ( EdgeToMachine.idAdjacentFace == OtherBottomFace.id) then
          dStripWidth = TOOLS[Cutting1.nToolIndex].dThickness + 2 * dStripWidth
       end
-      dDepthToMachine = min( TOOLS[Cutting1.nToolIndex].dMaxMaterial, EdgeToMachine.dElevation - dStripWidth)
+      -- se richiesto, si calcola il codolo verticale
+      if bAllowPerpendicularStrip and FeatureLib.IsMachiningLong( Cutting2.dEdgeLength, Part) then
+         dDepthToMachine = TOOLS[Cutting1.nToolIndex].dMaxMaterial - 10
+      else
+         dDepthToMachine = min( TOOLS[Cutting1.nToolIndex].dMaxMaterial, EdgeToMachine.dElevation - dStripWidth)
+      end
+
       OptionalParametersFaceByBlade1.dDepthToMachine = dDepthToMachine
+      OptionalParametersFaceByBlade1.bAllowPerpendicularStrip = bAllowPerpendicularStrip
 
       Cutting1 = FaceByBlade.Make( Proc, Part, BottomFace, EdgeToMachine, OptionalParametersFaceByBlade1)
       Cutting1.nInternalSortingPriority = 2
@@ -250,6 +266,7 @@ function BLADEKEEPWASTE.Make( Proc, Part, OptionalParameters)
    local bFinishWithMill = ( OptionalParameters.bFinishWithMill ~= false)
    local dMillingOffsetFromSide = OptionalParameters.dMillingOffsetFromSide or 1
    local dStripWidth = OptionalParameters.dStripWidth or 5
+   local bAllowPerpendicularStrip = OptionalParameters.bAllowPerpendicularStrip or false
    local bForced = OptionalParameters.bForced or false
 
    -- volume della feature
@@ -296,6 +313,7 @@ function BLADEKEEPWASTE.Make( Proc, Part, OptionalParameters)
       dExtendAfterTail = dExtendAfterTail,
       nToolIndex = nToolIndex,
       dStripWidth = dStripWidth,
+      bAllowPerpendicularStrip = bAllowPerpendicularStrip,
       OtherBottomFace = BottomFace2
    }
    local Cuttings1 = MakeBottomFace( Proc, Part, BottomFace1, BottomEdgeToMachine1, Parameters1)
@@ -427,6 +445,37 @@ function BLADEKEEPWASTE.Make( Proc, Part, OptionalParameters)
       Machinings = MachiningLib.GetSplitMachinings( Machinings, FeatureSplittingPoints, Part)
    end
 
+   -- se codoli perpendicolari, si accorciano LeadIn/LeadOut
+   if bAllowPerpendicularStrip then
+      for j = 1, #Machinings do
+         if Machinings[j].bIsMachiningSplitted then
+            -- se primo spezzone
+            if Machinings[j].bIsFirstSegment then
+               if MachiningLib.StartsLeftSide( Machinings[j]) then
+                  Machinings[j].LeadIn.dStartAddLength = Machinings[j].LeadIn.dStartAddLength - Machinings[j].dToolMarkLength - dStripWidth
+                  Machinings[j].LeadOut.dEndAddLength = Machinings[j].LeadOut.dEndAddLength - dStripWidth
+               else
+                  Machinings[j].LeadOut.dEndAddLength = Machinings[j].LeadOut.dEndAddLength - Machinings[j].dToolMarkLength - dStripWidth
+                  Machinings[j].LeadIn.dStartAddLength = Machinings[j].LeadIn.dStartAddLength - dStripWidth
+               end
+            -- se ultimo spezzone
+            elseif Machinings[j].bIsLastSegment then
+               if MachiningLib.StartsLeftSide( Machinings[j]) then
+                  Machinings[j].LeadOut.dEndAddLength = Machinings[j].LeadOut.dEndAddLength - Machinings[j].dToolMarkLength - dStripWidth
+                  Machinings[j].LeadIn.dStartAddLength = Machinings[j].LeadIn.dStartAddLength - dStripWidth
+               else
+                  Machinings[j].LeadIn.dStartAddLength = Machinings[j].LeadIn.dStartAddLength - Machinings[j].dToolMarkLength - dStripWidth
+                  Machinings[j].LeadOut.dEndAddLength = Machinings[j].LeadOut.dEndAddLength - dStripWidth
+               end
+            -- se spezzoni centrali
+            else
+               Machinings[j].LeadIn.dStartAddLength = Machinings[j].LeadIn.dStartAddLength - Machinings[j].dToolMarkLength - dStripWidth
+               Machinings[j].LeadOut.dEndAddLength = Machinings[j].LeadOut.dEndAddLength - Machinings[j].dToolMarkLength - dStripWidth
+            end
+         end
+      end
+   end
+
    -- ordinamento
    table.sort( Machinings, SortMachiningsBySegment)