- Nuovo ToolHolder

- Allineamento con common ver. 2.7k3

Beam/BeamData.lua

@@ -68,13 +68,16 @@ local BeamData = {
    KIOTP = 5,                                 -- coefficiente moltiplicativo per attacco/uscita lama tangente anzichè perpendicolare
    MAXDIAM_POCK_CORNER = 31,                  -- diametro massimo utensile ammesso per tasche con angoli interni
    USE_LONGCUT = true,                        -- per i tagli longitudinali usare solo la lavorazione di lama LongCut
-   PRECUT_HEAD = true,                      -- flag abilitazione pretaglio grezzo a zero in testa
-   PRECUT_TAIL = true,                      -- flag abilitazione pretaglio grezzo a zero in coda
+   HEAD_DIM_FOR_BH = 125,                     -- dimensione di ingombro della testa per block haus
+   MAX_LEN_BH_FROM_BOTTOM = 210,              -- massima lunghezza lavorabile da un lato di block haus da sotto
+   MAX_DIST_BH_FROM_BOTTOM = 600,             -- massima distanza tra naso mandrino e sopra della trave senza collisione
    ADVANCE_TAIL_CUT = true,                   -- per spostare prima del taglio di separazione il taglio di coda su pezzi corti con robabile caduta
    ADVANCE_TAIL_OFFS = 10,                    -- accorciamento taglio di coda avanzato (minimo 1)
    DOUBLE_HEAD_DOVETAIL = false,              -- flag abilitazione lavorazione mortase a coda di rondine in doppio
    DOUBLE_HEAD_MORTISE = false,               -- flag abilitazione lavorazione mortase in doppio
    DOUBLE_HEAD_DRILLING = false,              -- flag abilitazione forature in doppio
+   PRECUT_HEAD = true,                        -- flag abilitazione pretaglio grezzo a zero in testa
+   PRECUT_TAIL = true,                        -- flag abilitazione pretaglio grezzo a zero in coda
    CLAMP5 = false                             -- presenza pinza speciale per pezzi piccoli
 }
 
@@ -99,6 +102,8 @@ if EgtExistsFile( sData) then
          if Machine.Offsets.DOUBLE_HEAD_DOVETAIL then BeamData.DOUBLE_HEAD_DOVETAIL = ( Machine.Offsets.DOUBLE_HEAD_DOVETAIL == 1) end
          if Machine.Offsets.DOUBLE_HEAD_MORTISE then BeamData.DOUBLE_HEAD_MORTISE = ( Machine.Offsets.DOUBLE_HEAD_MORTISE == 1) end
          if Machine.Offsets.DOUBLE_HEAD_DRILLING then BeamData.DOUBLE_HEAD_DRILLING = ( Machine.Offsets.DOUBLE_HEAD_DRILLING == 1) end
+         if Machine.Offsets.PRECUT_HEAD_DISABLE then BeamData.PRECUT_HEAD = ( Machine.Offsets.PRECUT_HEAD_DISABLE == 0) end
+         if Machine.Offsets.PRECUT_TAIL_DISABLE then BeamData.PRECUT_TAIL = ( Machine.Offsets.PRECUT_TAIL_DISABLE == 0) end
          BeamData.MINRAW_S = max( BeamData.MINRAW_S, Machine.Offsets.MINRAW_S or BeamData.MINRAW_S)
          BeamData.MINRAW_L = max( BeamData.MINRAW_L, Machine.Offsets.MINRAW_L or BeamData.MINRAW_L)
          BeamData.CUT_EXTRA = Machine.Offsets.CUT_EXTRA or BeamData.CUT_EXTRA
@@ -113,8 +118,7 @@ if EgtExistsFile( sData) then
          BeamData.LEN_SHORT_PART = Machine.Offsets.LEN_SHORT_PART or BeamData.LEN_SHORT_PART
          BeamData.OVM_MID = Machine.Offsets.OVM_MID or BeamData.OVM_MID
          if Machine.Offsets.ROT90 ~= nil then BeamData.ROT90 = ( Machine.Offsets.ROT90 == 1) end
-         if Machine.Offsets.PRECUT_HEAD_DISABLE then BeamData.PRECUT_HEAD = ( Machine.Offsets.PRECUT_HEAD_DISABLE == 0) end
-         if Machine.Offsets.PRECUT_TAIL_DISABLE then BeamData.PRECUT_TAIL = ( Machine.Offsets.PRECUT_TAIL_DISABLE == 0) end
+         if Machine.Offsets.CUT_SIC then BeamData.CUT_SIC = EgtClamp( Machine.Offsets.CUT_SIC, 15, 50) end
       end
       if Machine.Trave then
          BeamData.MIN_WIDTH = Machine.Trave.XMIN or BeamData.MIN_WIDTH
@@ -226,6 +230,7 @@ local function GetSetupInfo( sHead)
    SetupInfo.bIsCSymmetrical = true
    SetupInfo.dCAxisEncumbrance = 180
    SetupInfo.bToolOnAggregate = false
+   SetupInfo.Head = {}
 
    -- testa 5 assi da sopra, dietro
    if sHead == 'H11' then

Beam/MachiningTypes.ini

@@ -37,6 +37,7 @@
 23=SmallToolContour
 24=AntiSplintMillCut
 25=Prof_end
+26=SideMillAsBlade
 
 [Pocketing]
 1=Pocket

Common_ONE-PF.NUM.mlpe

@@ -129,6 +129,11 @@ function OnToolData()
       local sOut = 'L1='..EgtNumToString( EMT.SMAX, 0)..' L2='..EmtLenToString( EMT.TDIST or ChSawLen, 1)
       sOut = sOut .. EgtIf( EMT.TCPOS == 'T111', ' G76H9998.2N411N414', ' G76H9998.2N511N514')
       EmtOutput( '('..sOut..')')
+   -- emissione dati aggregato BlockHaus
+   elseif EMT.HEAD == 'H17' then
+      sPos = EgtIf( #EMT.TCPOS == 2, EMT.TCPOS:gsub( 'T', 'N30'), EMT.TCPOS:gsub( 'T', 'N3'))
+      local sOut = 'L1='..EgtNumToString( EMT.SMAX, 0)..' L2='..EmtLenToString( ( AngTrBHOffs), 1)..' G76H9998.2'..sPos..sPos
+      EmtOutput( '('..sOut..')')
    -- emissione dati utensile (esclusa sega a catena)
    else
       -- output info
@@ -142,7 +147,6 @@ function OnToolData()
       if EMT.TCPOS == 'T201' then
          sPos = 'N411'
       else
-
          sPos = EgtIf( #EMT.TCPOS == 2, EMT.TCPOS:gsub( 'T', 'N30'), EMT.TCPOS:gsub( 'T', 'N3'))
       end
       local sOut = 'L1='..EgtNumToString( EMT.SMAX, 0)..' L2='..EmtLenToString( dAddLen + EMT.TTOTLEN, 1)..' G76H9998.2'..sPos..sPos
@@ -310,6 +314,8 @@ function OnDispositionEnd()
    else
       if #EMT.MDCHAR > 0 then
          MyOutputNoNum( '(PART UNLOAD)')
+         -- movimento intermedio di apertura pinza-rulli per evitare di trovare delle collisioni
+         EmitParkRoller( EMT.TPOS, false, false)
          for i = 1, #EMT.MDCHAR do
             EmitMoveDataChars( EMT.MDCHAR[i])
             if EMT.MDCHAR[i].V1 then EMT.V1POS = EMT.MDCHAR[i].V1 end
@@ -676,7 +682,7 @@ function OnPathStart()
    if EMT.TOOL == EMT.PREVTOOL and not EMT.ZMAX then
       EMT.L1pp = EMT.L1op
       EMT.L2pp = EMT.L2op
-      EMT.L3pp = EMT.L3op
+      EMT.L3pp = EMT.L3op or EMT.L3pp
       EMT.R1pp = EMT.R1p or EMT.R1pp
       EMT.R2pp = EMT.R2p or EMT.R2pp
    else
@@ -1145,7 +1151,7 @@ function OnRapid()
       else
          --EmtOutput( string.format( 'V1Pos=%.3f V2Pos=%.3f', EMT.V1POS, EMT.V2POS))
          local bToPresel = true
-         if not EMT.RELOAD and not EMT.ZMAX and #EMT.AUXCMD > 0 and EMT.TO_ZMAX then
+         if not EMT.ZMAX and #EMT.AUXCMD > 0 and EMT.TO_ZMAX then
             -- allontanamento o eventuale preselezione successiva testa differente
             if not EMT.DOU_TYPE then
                PreselectNextDiffHead( EMT.MCHID, EMT.HEAD)
@@ -1788,24 +1794,6 @@ function OnArc()
    EmtUpdatePrev()
 end
 
----------------------------------------------------------------------
-function CalcDinamicaPinze( dH, dS, dL)
-   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
-   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
-   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
-   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
-   local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito) / 1000)
-   local AccMaxPinze = EMT.MAXACC
-   local AccPinze = EgtClamp( FMaxPinze / ( 60 * TempoAcc), EMT.MINACC, EMT.MAXACC)
-   local RidFeed = 100 / Massa * 100
-   if RidFeed > 100 then
-      RidFeed = 100
-   elseif RidFeed < 10 then
-      RidFeed = 10
-   end
-   return AccPinze, AccMaxPinze, RidFeed
-end
-
 ---------------------------------------------------------------------
 function CalcCharStatusN( sCmd)
    -- aperto
@@ -2284,7 +2272,7 @@ function PreparePreRotation( sCmd, nInd)
             MDChar = { [Cmd[2]]=tonumber(Cmd[3]), IniStatY1=86, FinStatY1=87, BeamVise=0}
          elseif EMT.SPECSPLIT or EMT.SPLITROT then
             MDChar = { [Cmd[2]]=tonumber(Cmd[3]), V1=ParkV1, IniStatY1=EMT.ISY1, FinStatY1=EMT.FSY1, IniStatY2=EMT.ISY2, FinStatY2=EMT.FSY2, IniStatV1=3, BeamVise=EMT.BV}
-            EMT.V1POS = MDChar.V1
+            EMT.V1NEXTPOS = MDChar.V1
          else
             MDChar = { [Cmd[2]]=tonumber(Cmd[3]), IniStatY1=EMT.ISY1, FinStatY1=EMT.FSY1, IniStatY2=EMT.ISY2, FinStatY2=EMT.FSY2, BeamVise=EMT.BV}
          end
@@ -2517,10 +2505,15 @@ function MyAdjustLinearAxes()
          local Len = ( EMT.TDIST or ChSawLen) + Mill2Offs
          local LenRef = Mill2Offs
          vtE = Vector3d( EMT.ADIR) * Len - Z_AX() * LenRef
+      elseif EMT.HEAD == 'H17' then
+         local LenAux = AngTrBHOffs + MillOffs
+         local LenRef = MillOffs
+         local vtAux = EgtGetCalcAuxDirFromAngles( EMT.R1, EMT.R2, EMT.R3)
+         vtE = vtAux * LenAux - Z_AX() * LenRef
       else
          EmtSetLastError( 1211, 'Head not defined ' .. ( EMT.HEAD or ''))
       end
-      if EMT.HEAD == 'H11' or EMT.HEAD == 'H12' or EMT.HEAD == 'H13' or EMT.HEAD == 'H15' then
+      if EMT.HEAD == 'H11' or EMT.HEAD == 'H12' or EMT.HEAD == 'H13' or EMT.HEAD == 'H15' or sHead == 'H17' then
          EMT.L1 = EMT.L1 - vtE:getX()
          EMT.L2 = EMT.L2 - DeltaTabY - vtE:getY()
          EMT.L3 = EMT.L3 - DeltaTabZ - vtE:getZ()
@@ -2633,6 +2626,9 @@ function GetToolRadLen()
    -- se sega a catena
    elseif HeadIsChainSaw( EMT.HEAD) then
       return EMT.TLEN, ( EMT.TDIST or ChSawLen)
+   -- se aggregato BlockHaus
+   elseif EMT.HEAD == 'H17' then
+      return EMT.TDIAM / 2, AngTrBHOffs
    end
 end
 
@@ -2654,7 +2650,7 @@ function CalcInterpPlane()
    local _, dAngV, dAngO = SphericalFromVector( vtE)
    local dAngO2 = EmtGetAngO2( EMT.IPLGLFR:getVersZ(), EMT.IPLGLFR:getVersX(), dAngV, dAngO)
    dAngO = dAngO + 90
-   while dAngO >= 360 do
+   while dAngO + 100 * GEO.EPS_SMALL > 360 do
       dAngO = dAngO - 360
    end   
    EMT.IPLGLSTR = ' EX0 EY'..EmtLenToString( xS)..' EZ0'..
@@ -3120,7 +3116,7 @@ function PreselectNextDiffHead( nMchId, sHead)
                EmitMoveStartHead( 1)
                EmitMoveWaitHead( 1)
             end
-            -- Emetto preselezione (non ammessa per sega a catena H13 e H23)
+            -- Emetto preselezione (non ammessa per sega a catena H13 e H23 e aggregato BlockHaus H17)
             if sNextHead == 'H11' then
                EmitMoveDataHead( 1, { X=-ParkX1, Z=MaxZ1, B=ParkB1, C=ParkC1, TPos=AdjustTcPos( false, sNextTcPos)})
                EmitMoveStartHead( 1)
@@ -3199,7 +3195,7 @@ function EmitTestProgramStart()
    EmtOutput( 'M12 $START PER SVINCOLO TESTE')
    EmtOutput( '(SVINCOLO TESTA 1)')
    EmitMoveDataHead( 1, {Z=ParkZ1-100, TPos=0})
-   if Progress then
+   if Progress or SecondToolChanger then
       EmtOutput( 'IF E80001<=10 THEN')
       EmitMoveDataHead( 1, {C=ParkC1, TPos=0})
       EmitMoveDataHead( 1, {Z=-150, B=ParkB1, TPos=0})

Common_ONE-PF.mlpe

@@ -79,6 +79,14 @@ function OnSimulStart()
          if vTools and vTools[1] and #(vTools[1]) > 0 then
             EgtLoadTool( vTcPos[i], 1, vTools[1])
             ShowToolInTcPos( vTcPos[i], true)
+            -- Aggiunto controllo lunghezza lama minima * 0.9 per ricavare la tolleranza del VMILL
+            if EgtTdbSetCurrTool(vTools[1]) then -- set utensile corrente
+               if EgtTdbGetCurrToolParam( MCH_TP.TYPE) == MCH_TY.SAW_STD or EgtTdbGetCurrToolParam( MCH_TP.TYPE) == MCH_TY.SAW_FLAT then -- controllo tipo utensile sega
+                  local dCurrSawLen = EgtTdbGetCurrToolParam( MCH_TP.LEN) * 0.9
+                  -- se non definito o minore del valore precedente aggiorna la tolleranza
+                  EMT.VMILLTOL = EgtIf( not EMT.VMILLTOL or dCurrSawLen < EMT.VMILLTOL, dCurrSawLen, EMT.VMILLTOL) 
+               end
+            end
          end
       end
    end
@@ -129,7 +137,7 @@ function OnSimulStart()
    end
 
    -- gruppo CHSAW si attiva solo se progress, one con BIT mortiser o PF
-   if Progress or Mortiser or EgtGetHeadId( 'H21') then
+   if Progress or Mortiser or EgtGetHeadId( 'H21') or SecondToolChanger then
       table.insert( McdData, { Grp = 'Base', Sub = 'COLLISION', Name = 'CHSAW'})
    end
    -- gruppo MORTISER si attiva solo se PF con BIT mortiser attivo
@@ -239,7 +247,7 @@ function OnSimulDispositionStart()
             -- determino la risoluzione dello Zmap
             local dTol = 4.71
             if EmtGetVMillStep then
-               dTol = EmtGetVMillStep( b3Raw:getDimX(), b3Raw:getDimY(), b3Raw:getDimZ(), 4.71)
+               dTol = EmtGetVMillStep( b3Raw:getDimX(), b3Raw:getDimY(), b3Raw:getDimZ(), dTol)
             else
                local dArea = b3Raw:getDimX() * b3Raw:getDimY() + b3Raw:getDimX() * b3Raw:getDimZ() + b3Raw:getDimY() * b3Raw:getDimZ()
                if dArea < 0.075e6 then
@@ -256,6 +264,7 @@ function OnSimulDispositionStart()
                   dTol = 3.77
                end
             end
+            dTol = min( dTol, EMT.VMILLTOL or dTol) -- imposto dTol al valore minore tra quello per volume e quello per spessore lama
             -- creo lo Zmap
             local VMillId = EgtVolZmapBox( nPartRawId, b3Raw:getMin(), b3Raw:getDimX(), b3Raw:getDimY(), b3Raw:getDimZ(), dTol, true, GDB_RT.GLOB)
             if VMillId then
@@ -472,6 +481,7 @@ function OnSimulDispositionEnd()
       EMT.UNLOADING = false
       EMT.FALL = false
       EMT.TO_FALL = false
+      EMT.Y2DELTA = nil
    end
    -- se disposizione intermedia
    if IsMidPhase( EMT.PHASE) or IsEnd2Phase( EMT.PHASE) then
@@ -646,7 +656,7 @@ function OnSimulToolDeselect( dPrevA)
                SimulMoveAxes( 'B1', ParkB1, MCH_SIM_STEP.RAPROT, 'C1', ParkC1, MCH_SIM_STEP.RAPROT)
                SimulMoveAxis( 'X1', ParkX1, MCH_SIM_STEP.RAPID)
             -- deposito utensile lama
-            elseif EMT.PREVHEAD_H1 == 'H12' then
+            elseif EMT.PREVHEAD_H1 == 'H12' or EMT.PREVHEAD_H1 == 'H17' then
                -- simulo movimento
                SimulMoveAxes( 'B1', ParkB1, MCH_SIM_STEP.RAPROT, 'C1', ParkC1, MCH_SIM_STEP.RAPROT)
                SimulMoveAxis( 'X1', ParkX1, MCH_SIM_STEP.RAPID)
@@ -714,12 +724,12 @@ function OnSimulToolDeselect( dPrevA)
       -- nascondo l'utensile sulla testa
       EgtSetMode( EgtGetHeadId( EMT.PREVHEAD_H1 or '') or GDB_ID.NULL, GDB_MD.HIDDEN)
       -- prendo utensile fresa o lama
-      if EMT.NEXTHEAD == 'H11' or EMT.NEXTHEAD == 'H12' then
+      if EMT.NEXTHEAD == 'H11' or EMT.NEXTHEAD == 'H12' or EMT.NEXTHEAD == 'H17' then
          local MyParkX1 = EgtIf( GetHeadTCSet( EMT.NEXTHEAD, EMT.NEXTTCPOS) == 'Head1_TC1', ParkX1, ParkFrnX1)
          local MyParkB1 = ParkB1
          local MyParkC1 = ParkC1
          -- se ho due teste oppure è progress, significa che ho CU verticale
-         if EgtGetHeadId('H21') or Progress then
+         if EgtGetHeadId('H21') or Progress or SecondToolChanger then
             MyParkB1 = EgtIf( GetHeadTCSet( EMT.NEXTHEAD, EMT.NEXTTCPOS) == 'Head1_TC1', ParkB1, ParkFrnB1)
             MyParkC1 = EgtIf( GetHeadTCSet( EMT.NEXTHEAD, EMT.NEXTTCPOS) == 'Head1_TC1', ParkC1, ParkFrnC1)
          -- altrimenti su one CU speciale motosega-utensile lungo
@@ -1088,7 +1098,7 @@ function OnSimulMoveStart()
       else
          if GetHeadTCSet( EMT.HEAD, EMT.TCPOS) == 'Head1_TC2' then
             -- se movimento iniziale da Zmax con lama o fresa
-            if EMT.HEAD == 'H11' or EMT.HEAD == 'H12' then
+            if EMT.HEAD == 'H11' or EMT.HEAD == 'H12' or EMT.HEAD == 'H17' then
                if EMT.ZMAX or EMT.FLAG == 1 or ( EMT.FLAG == 2 and EMT.FLAG2 == 1) then
                   --EgtOutBox( 'Flag 2,1', 'Info Rapid')
                   local bMoveZbeforeX = false
@@ -1599,7 +1609,15 @@ function ExecMoveHome( bNearV, bMchSplit)
          EMT.CHSAW_OUT = true
       end
       -- porto le teste in home
-      SimulMoveAxes( 'X1', ParkX1, MCH_SIM_STEP.RAPID, 'X2', ParkX2, MCH_SIM_STEP.RAPID)
+      if EgtGetHeadId( 'H21') then
+         SimulMoveAxes( 'X1', ParkX1, MCH_SIM_STEP.RAPID, 'X2', ParkX2, MCH_SIM_STEP.RAPID)
+      else
+         if GetHeadTCSet( EMT.HEAD, EMT.TCPOS) == 'Head1_TC1' then
+            SimulMoveAxes( 'X1', ParkX1, MCH_SIM_STEP.RAPID)
+         else
+            SimulMoveAxes( 'X1', ParkFrnX1, MCH_SIM_STEP.RAPID)
+         end
+      end
       -- sistemo i rulli
       ExecOpenRoller( 1)
       ExecOpenRoller( 2)
@@ -1691,7 +1709,7 @@ function ExecMoveZmax( bMchSplit, btoXHome)
             SimulMoveAxis( 'Z1', MaxZ1, MCH_SIM_STEP.RAPID)
             if btoXHome then
                EMT.XHOME = true
-               SimulMoveAxis( 'X1', ParkX1, MCH_SIM_STEP.RAPID)
+               SimulMoveAxis( 'X1', HomeX, MCH_SIM_STEP.RAPID)
             end
          -- altrimenti sega a catena
          else
@@ -1702,6 +1720,8 @@ function ExecMoveZmax( bMchSplit, btoXHome)
             if btoXHome then
                EgtUnloadTool( EMT.HEAD, 1)
                ShowToolInTcPos( EMT.TCPOS, true)
+               -- nascondo l'utensile sulla testa
+               EgtSetMode( EgtGetHeadId( EMT.HEAD or '') or GDB_ID.NULL, GDB_MD.HIDDEN)
                EMT.PREVTOOL_H1 = nil
                EMT.PREVHEAD_H1 = nil
                EMT.PREVTCPOS_H1 = nil
@@ -2225,11 +2245,17 @@ end
 
 ---------------------------------------------------------------------
 function ShowToolInTcPos( sTcPos, bShow)
+   -- recupero identificativo della posizione sul TC
+   local TcPosId = EgtGetTcPosId( sTcPos or '')
+   if not TcPosId then return end
    -- recupero il gruppo dell'utensile
-   local TcExitId = EgtGetFirstNameInGroup( EgtGetTcPosId( sTcPos or '') or GDB_ID.NULL, 'T1')
+   local TcExitId = EgtGetFirstNameInGroup( TcPosId or GDB_ID.NULL, 'T1')
    if not TcExitId then return end
    -- imposto lo stato di visualizzazione
    EgtSetStatus( TcExitId, EgtIf( bShow, GDB_ST.ON, GDB_ST.OFF))
+   -- recupero eventuale gruppo ausiliario da visualizzare/nascondere
+   local TcHSId = EgtGetFirstNameInGroup( TcPosId, sTcPos .. '_HS')
+   if TcHSId then EgtSetStatus( TcHSId, EgtIf( bShow, GDB_ST.ON, GDB_ST.OFF)) end
 end
 
 ---------------------------------------------------------------------
@@ -2250,7 +2276,7 @@ function LoadNextTool( nHSet, sTcPosDef, bFirst)
       if vTools and vTools[1] and #(vTools[1]) > 0 then
          sTool = vTools[1]
          sTcPos = sTcPosDef
-         if Progress then
+         if Progress or SecondToolChanger then
             sHead = EgtIf( sTcPos == 'T11', 'H12', 'H11')
          elseif nHSet == 1 then
             sHead = EgtIf( sTcPos == 'T1', 'H12', 'H11')
@@ -2307,6 +2333,9 @@ local FALL_T = 2 * ESTIMATION_RAPID_COEFF              -- s
 ---------------------------------------------------------------------
 function OnEstimStart()
    EMT.INCHES = not EgtUiUnitsAreMM()      -- unità di misura mm/inches
+   EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 102000, 20000, 102000)  -- feed massima pinze
+   EMT.MAXACC = MaxAcc or ( EMT.FMAXPINZE / ( 60 * 0.3))  -- accelerazione massima pinze
+   EMT.MINACC = MinAcc or ( EMT.FMAXPINZE / ( 60 * 4))    -- accelerazione minima pinze
 end
 
 ---------------------------------------------------------------------
@@ -2392,6 +2421,15 @@ function OnEstimDispositionEnd()
    EMT.OPEISDISP = false
 end
 
+---------------------------------------------------------------------
+function OnEstimRawMoveData()
+   -- se start del pezzo
+   if IsStartOrRestPhase( EMT.PHASE) then
+      EMT.SPLIT = false
+   end
+   OnRawMoveData()
+end
+
 ---------------------------------------------------------------------
 function OnEstimToolSelect()
    -- reset indice utensile in tabella lunghezze
@@ -2448,6 +2486,12 @@ function OnEstimMachiningEnd()
       EMT.TLE_NAME = nil
       EMT.TLE_TIME = nil
    end
+
+   EMT.MCHUSERNOTES = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   EMT.MCHSPLIT = ( EMT.MCHUSERNOTES:find( 'Split;', 1, true) ~= nil)
+   if EMT.MCHSPLIT then
+      EMT.SPLIT = true
+   end
 end
 
 ---------------------------------------------------------------------
@@ -2573,11 +2617,11 @@ function OnEstimRapid()
    EMT.MCHEXTLEN = EMT.MCHEXTLEN + dLen
    -- calcolo tempo
    local dTime = RAPID_MIN_T
-   local dT1 = abs( dL1) / RAPID_X_FEED * 60
+   local dT1 = CalcMoveTime( abs( dL1), RAPID_X_FEED, EMT.SPLIT)
    if dT1 > dTime then dTime = dT1 end
-   local dT2 = abs( dL2) / RAPID_Y_FEED * 60
+   local dT2 = CalcMoveTime( abs( dL2), EMT.FMAXPINZE, EMT.SPLIT)
    if dT2 > dTime then dTime = dT2 end
-   local dT3 = abs( dL3) / RAPID_Z_FEED * 60
+   local dT3 = CalcMoveTime( abs( dL3), RAPID_Z_FEED, EMT.SPLIT)
    if dT3 > dTime then dTime = dT3 end
    local dT4 = abs( dR1) / RAPID_C_FEED * 60
    if dT4 > dTime then dTime = dT4 end
@@ -2599,7 +2643,7 @@ function OnEstimLinear()
    local dLen = sqrt( dL1 * dL1 + dL2 * dL2 + dL3 * dL3)
    EMT.MCHCUTLEN = EMT.MCHCUTLEN + dLen
    -- calcolo tempo
-   local dTime = dLen / EMT.F * 60
+   local dTime = CalcMoveTime( dLen, EMT.F, EMT.SPLIT)
    EMT.MCHCUTTIME = EMT.MCHCUTTIME + dTime
    EgtOutLog( string.format( '  G1 Len=%.0f Time=%.2f', dLen, dTime), 5)
    -- aggiorno valori come precedenti
@@ -2853,10 +2897,10 @@ end
 
 ---------------------------------------------------------------------
 function RollerParkingNeeded( sHead, dAng1p, dAng2p, dAng1, dAng2)
-   if sHead == 'H11' or sHead == 'H12'  or HeadIsChainSaw( sHead) then
-      return ( abs( dAng1 - dAng1p) > 1 or ( abs( dAng2 - dAng2p) > 1 and abs( dAng1 % 180.0) > 1))
+   if sHead == 'H11' or sHead == 'H12'  or sHead == 'H17' or HeadIsChainSaw( sHead) then
+      return ( abs( dAng1 - dAng1p) > 1 or ( abs( dAng2 - dAng2p) > 1 and abs( dAng1) % 180.0 > 1))
    elseif sHead == 'H21' or sHead == 'H22' or HeadIsChainSaw( sHead) then
-      return ( abs( dAng1 - dAng1p) > 1 or ( abs( dAng2 - dAng2p) > 1 and abs( dAng1 % 180.0) > 1))
+      return ( abs( dAng1 - dAng1p) > 1 or ( abs( dAng2 - dAng2p) > 1 and abs( dAng1) % 180.0 > 1))
    end
 end
 
@@ -2871,5 +2915,40 @@ function GetCmdAxMove( Cmd, sAx)
    end
 end
 
+---------------------------------------------------------------------
+function CalcDinamicaPinze( dH, dS, dL)
+   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
+   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
+   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
+   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
+   local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito) / 1000)
+   local AccMaxPinze = EMT.MAXACC
+   local AccPinze = EgtClamp( FMaxPinze / ( 60 * TempoAcc), EMT.MINACC, EMT.MAXACC)
+   local RidFeed = 100 / Massa * 100
+   if RidFeed > 100 then
+      RidFeed = 100
+   elseif RidFeed < 10 then
+      RidFeed = 10
+   end
+   return AccPinze, AccMaxPinze, RidFeed
+end
+
+---------------------------------------------------------------------
+function CalcMoveTime( dPathLen, dFeed, bIsSplitted)
+   local dTime
+   local dFeedInSec = dFeed / 60
+   local dAcc, _, _ = CalcDinamicaPinze( EMT.HB, EMT.SB, EgtIf( bIsSplitted, EMT.LT, EMT.LB))
+
+   -- Caso 1: dFeed raggiunta
+   if dPathLen >= ( dFeedInSec ^ 2) / dAcc then
+      dTime = ( dFeedInSec / dAcc) + ( dPathLen / dFeedInSec)
+   -- Caso 2: dFeed non raggiunta
+   else
+      dTime = 2 * sqrt( dPathLen / dAcc)
+   end
+
+   return dTime
+end
+
 ---------------------------------------------------------------------
 -- *** END GENERAL ***

Common_ONE-PF.mlse

@@ -7,6 +7,31 @@ EgtEnableDebug( false)
 -- Carico libreria
 local BD = require( 'BeamData')
 
+---------------------------------------------------------------------
+-- *** Generic Machinings ***
+---------------------------------------------------------------------
+require( 'EmtGenMachining')
+
+---------------------------------------------------------------------
+-- *** Special GetPrevMachiningOffset ***
+---------------------------------------------------------------------
+-----------------------------------------------------------------------------------------
+function OnSpecialGetPrevMachiningOffset()
+   -- default
+   EMC.ERR = 0
+   EMC.PREVOFFSX = 0
+   -- se c'è cambio di fase tra le lavorazioni (quindi la precedente è l'ultima della sua fase e la corrente la prima)
+   if EMC.PREVPHASE ~= EMC.CURRPHASE then
+      -- se la fase corrente è di inizio lavorazione di nuova trave
+      if IsStartOrRestPhase( EMC.CURRPHASE) then
+         -- recupero la posizione finale della lavorazione precedente
+         local vPrevAx = EmtGetFinalAxesPos( EMC.PREVMCHID)
+         -- la X (L1) di questa corrisponde alla posizione iniziale della nuova trave, se ne deduce l'offset
+         EMC.PREVOFFSX = ParkV1 - vPrevAx[1]
+      end
+   end
+end
+
 ---------------------- OnSpecialGetMaxZ -----------------------------
 ---------------------------------------------------------------------
 local function CalcExtraZ( vtTp, vtT, vMZ)
@@ -72,7 +97,7 @@ function OnSpecialGetMaxZ()
          local vMZ = {{ Tz=0.85, Ez=390}, { Tz=0.5, Ez=280}, { Tz=-0.01, Ez=160}, { Tz=-0.5, Ez=1}, { Tz=-0.61, Ez=1}}
          EMC.MAXZ = ParkZ1 + CalcExtraZ( vtTpZm, vtT, vMZ)
       end
-   elseif EMC.HEAD == 'H12' and sHead_TC == 'Head1_TC1' then
+   elseif ( EMC.HEAD == 'H12' or EMC.HEAD == 'H17') and sHead_TC == 'Head1_TC1' then
       if vtTp:getX() > 0.4 and vtT:getX() > 0.4 then
          if bBSameSign and abs( EMC.R1 - EMC.R1p) < 165 then
             EMC.MAXZ = MaxZ1 - EgtIf( abs( EMC.R2) < 90.1 and abs( EMC.R2p) < 90.1, 0, 130)
@@ -173,7 +198,7 @@ function OnSpecialMoveZup()
    if EMC.HEAD == 'H11' or EMC.HEAD == 'H21' then
       ;
    -- se lama posizionata su CU prossimo a testa 1
-   elseif EMC.HEAD == 'H12' and sHead_TC == 'Head1_TC1' then
+   elseif ( EMC.HEAD == 'H12' or EMC.HEAD == 'H17') and sHead_TC == 'Head1_TC1' then
       -- se inclinata oltre 90 gradi e interferisce con la trave
       if ( EMC.R2 > 87.9 and ( EMC.R1 < 15.0 or EMC.R1 > 180.0)) or ( EMC.R2 < -87.9 and ( EMC.R1 > -15.0 and EMC.R1 < 180.0)) then
          local dZref = dZmax + min( 330 * vtT:getZ(), 0) + 260 * ( 1 - sqrt( 1- vtT:getZ() * vtT:getZ()))

Essetre-PFrl.ini

@@ -108,6 +108,7 @@ H11.1=Standard.nge
 H11.1:MILL_NOTIP=MillNoTip.nge
 H12.1=Saw.nge
 H13.1=ChainSaw.nge
+H17.1=AngTransmBH.nge
 H21.1=Standard.nge
 H21.1:MILL_NOTIP=MillNoTip.nge
 H22.1=Saw.nge
@@ -136,6 +137,8 @@ H11=6608
 H12=6615
 ; Chainsaw
 H13=6616
+; Angular transmission
+H17=6617
 ; Second 5 axis head
 H21=6620
 ; Second 5 axis saw

Essetre-PFrl.mlde

@@ -44,10 +44,10 @@
 require( 'EmtGenerator')
 EgtEnableDebug( false)
 
-PP_VER = '2.7h2'
-PP_NVER = '2.7.8.2'
+PP_VER = '2.7k3'
+PP_NVER = '2.7.11.3'
 MIN_MACH_VER = '2.5k1'
-MACH_NAME = 'Essetre-PFrl'
+MACH_NAME = string.match( EgtGetCurrMachineDir(), "[^\\]+$")  -- si ricava il nome della macchina dal direttorio
 
 -- Carico i dati globali
 local sMachDir = EgtGetCurrMachineDir()
@@ -155,6 +155,8 @@ ParkB2 = -90
 MinDeltaX1X2 = 650
 MinDistToolX1X2 = 40
 LimX2RotSaw = 800
+AngTrBHOffs = 154.5
+AngTrBHLen = 90
 TurnerOffs = 120.0
 AggLoad = 50
 DeltaTabY = 1170.0
@@ -172,8 +174,11 @@ DefTcPos1 = 'T3'
 DefTcPos2 = 'T13'
 SecondSaw = false
 AutomaticRotation = true
+OptimizedLoadBeam = true
 AutoRotMinLen = 0
+EstimationRapidMultiplier = 1
 ForceToCloseRollersGate = false
+AggreBlockHaus = false
 
 -- Aggiornamento con dati da TechnoEssetre7
 local sTs3Data = EgtGetStringFromIni( 'Beam', 'DATA_DIR', "C:\\TechnoEssetre7\\EgtData", EgtGetIniFile()).."\\Essetre-PFrl.data"
@@ -255,14 +260,18 @@ if EgtExistsFile( sData) then
          if Machine.Offsets.SAWOFFSZ then SawOffsZ = Machine.Offsets.SAWOFFSZ end
          if Machine.Offsets.SAW2OFFSX then Saw2OffsX = Machine.Offsets.SAW2OFFSX end
          if Machine.Offsets.SAW2OFFSZ then Saw2OffsZ = Machine.Offsets.SAW2OFFSZ end
+         if Machine.Offsets.DEFTCPOS1 then DefTcPos1 = ( 'T' .. Machine.Offsets.DEFTCPOS1) end
+         if Machine.Offsets.DEFTCPOS2 then DefTcPos2 = ( 'T' .. Machine.Offsets.DEFTCPOS2) end
          if Machine.Offsets.NOULOAD then MaxUnloadLen = Machine.Offsets.NOULOAD end
          if Machine.Offsets.MAXFEEDPINZE then MaxFeedPinze = Machine.Offsets.MAXFEEDPINZE end
          if Machine.Offsets.MAXACC then MaxAcc = Machine.Offsets.MAXACC end
          if Machine.Offsets.MINACC then MinAcc = Machine.Offsets.MINACC end
-         if Machine.Offsets.DEFTCPOS1 then DefTcPos1 = ( 'T' .. Machine.Offsets.DEFTCPOS1) end
-         if Machine.Offsets.DEFTCPOS2 then DefTcPos2 = ( 'T' .. Machine.Offsets.DEFTCPOS2) end
+         if Machine.Offsets.COEFF_STIMATEMPI and Machine.Offsets.COEFF_STIMATEMPI > 0 then EstimationRapidMultiplier = Machine.Offsets.COEFF_STIMATEMPI end
          if Machine.Offsets.CHIUDI_PINZE_2_3_SCAMBIO then ForceToCloseRollersGate = Machine.Offsets.CHIUDI_PINZE_2_3_SCAMBIO == 1 end
          if Machine.Offsets.WOOD_DENSITY then WoodDensity = Machine.Offsets.WOOD_DENSITY end
+         if Machine.Offsets.AGGRE_BH then AggreBlockHaus = ( Machine.Offsets.AGGRE_BH == 1) end
+         AngTrBHOffs = Machine.Offsets.OFFSETZ_RINV_BH or AngTrBHOffs
+         AngTrBHLen = Machine.Offsets.OFFSETX_RINV_BH or AngTrBHLen
          if Machine.Offsets.MAX_BACK_CLAMP_5 then MaxBackClamp5 = Machine.Offsets.MAX_BACK_CLAMP_5 end
          -- aggiustamenti
          MinY1 = MinV1 + MinDeltaYV
@@ -399,6 +408,24 @@ local H13Id = EmtHead {
       Geo = 'H13_HEAD/GEO'}
 EgtSetInfo( H13Id, 'ZSAFEDELTA', '60')
 EgtSetInfo( H13Id, 'ZMAXONROT', '1,80')
+
+-- Eventuale aggregato per lavorazioni BlockHaus
+if AggreBlockHaus then
+   local H17Id = EmtHead {
+      Name = 'H17',
+      Parent = 'B1',
+      HSet = 'H11',
+      Type = MCH_HT.STD,
+      Pos = Point3d( -AngTrBHLen, 0, -AngTrBHOffs),
+      TDir = X_AX(),
+      ADir = Z_AX(),
+      Rot1W = 0.2,
+      SolCh = MCH_SCC.ADIR_NEAR,
+      OthColl = {'H2', 'B/SOLID', 'C/SOLID'},
+      Geo = 'H17_HEAD/GEO',
+      Aux = {'H17_HEAD/SOLID', 'H17_HEAD/COLLISION'}}
+end
+
 --  *** Testa 2 ***
 local X2Id = EmtAxis {
       Name = 'X2',
@@ -634,6 +661,7 @@ EmtTable {
       Parent = 'T',
       Type = MCH_TT.FLAT,
       Ref1 = Point3d( -DimTabX, DeltaTabY, DeltaTabZ),
+      Coll = 'Base/BELT',
       Geo = 'TABLE/GEO',
       Aux = 'TABLE/SOLID'}
 -- *** ToolChanger ***
@@ -688,13 +716,24 @@ EmtTcPos {
       TDir = -Y_AX(),
       ADir = -X_AX(),
       Geo = 'BASE/T8'}
-EmtTcPos {
+if AggreBlockHaus then
+   local TcpSsId = EmtTcPos {
+         Name = 'T9',
+         Parent = 'Base',
+         Pos = ptTc1 + 8 * vtDt1 + Vector3d( -AngTrBHLen, AngTrBHOffs, 0),
+         TDir = X_AX(),
+         ADir = -Y_AX(),
+         Geo = 'BASE/T9_BH',
+         Aux = 'BASE/T9_HS'}
+else
+   EmtTcPos {
       Name = 'T9',
       Parent = 'Base',
       Pos = ptTc1 + 8 * vtDt1,
       TDir = -Y_AX(),
       ADir = -X_AX(),
       Geo = 'BASE/T9'}
+end
 EmtTcPos {
       Name = 'T10',
       Parent = 'Base',
@@ -804,6 +843,10 @@ EgtMove( EgtGetFirstNameInGroup( BaseId, 'TC3') or GDB_ID.NULL, vtMovB, GDB_RT.G
 if Mortiser then 
    EgtMove( EgtGetFirstNameInGroup( BaseId, 'TC4') or GDB_ID.NULL, vtMovB, GDB_RT.GLOB)
 end
+-- sposto geometria aggiuntiva agrgegato BlockHaus
+if AggreBlockHaus then
+   EgtMove( EgtGetFirstNameInGroup( EgtGetFirstNameInGroup( BaseId, 'T9'), 'T9_HS') or GDB_ID.NULL, vtMovB, GDB_RT.GLOB)
+end
 EgtMove( EgtGetFirstNameInGroup( X1Id, 'SOLID'), vtMovB, GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( X1Id, 'COLLISION'), vtMovB, GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( X2Id, 'SOLID'), vtMovB, GDB_RT.GLOB)
@@ -851,7 +894,7 @@ function OnSetHead()
       EmtModifyAxisHome( 'B1', ParkB1)
       EmtModifyAxisDirection( 'B1', X_AX())
    -- se testa H12 (lama)
-   elseif EMC.HEAD == 'H12' then
+   elseif EMC.HEAD == 'H12' or EMC.HEAD == 'H17' then
       EmtModifyAxisHome( 'X1', ParkX1)
       EmtModifyAxisHome( 'Z1', ParkZ1)
       EmtModifyAxisHome( 'C1', ParkC1)
@@ -893,9 +936,9 @@ end
 
 ---------------------------------------------------------------------
 function GetHeadSet( sHead)
-   if sHead == 'H11' or sHead == 'H12' or sHead == 'H13' then
+   if sHead == 'H11' or sHead == 'H12' or sHead == 'H13' or sHead == 'H15' or sHead == 'H17' then
       return 1
-   elseif sHead == 'H21' or sHead == 'H22' then
+   elseif sHead == 'H21' or sHead == 'H22' or sHead == 'H23' then
       return 2
    else
       return 0
@@ -907,7 +950,7 @@ end
 function GetHeadTCSet( sHead, sTcPos)
    local nPos = tonumber( string.sub( sTcPos, 2)) or 0
    -- testa 1
-   if sHead == 'H11' or sHead == 'H12' or sHead == 'H13' or sHead == 'H15' then
+   if sHead == 'H11' or sHead == 'H12' or sHead == 'H13' or sHead == 'H15' or sHead == 'H17' then
       -- testa 1 su CU prossimo a testa 2
       if nPos > 10 then
          return 'Head1_TC2'
@@ -971,7 +1014,7 @@ end
 ---------------------------------------------------------------------
 -- Funzione che ritorna ZExtra partendo dalla testa e dall'angolo verticale
 function GetZExtra( sHead, dAngV)
-   if sHead == 'H11' or sHead == 'H21' then
+   if sHead == 'H11' or sHead == 'H21' or sHead == 'H17' then
       if abs( dAngV) < 30.1 then
          return 400
       elseif abs( dAngV) < 45.1 then

Scripts/SetUp.lua

@@ -30,6 +30,7 @@ local GS = {}
 -- Configurazione posizioni (con o senza TC2)
 local PositionTable = {}
 local SecondSaw = ( EgtGetHeadId( 'H22') ~= nil)
+local AggreBH = ( EgtGetHeadId( 'H17') ~= nil)
 if SecondSaw then
    PositionTable = {{Pos = "Pos1",  TcPos = "T1",  Head = "H12", Group = "G1"},
                     {Pos = "Pos2",  TcPos = "T3",  Head = "H11", Group = "G1"},
@@ -38,7 +39,7 @@ if SecondSaw then
                     {Pos = "Pos5",  TcPos = "T6",  Head = "H11", Group = "G1"},
                     {Pos = "Pos6",  TcPos = "T7",  Head = "H11", Group = "G1"},
                     {Pos = "Pos7",  TcPos = "T8",  Head = "H11", Group = "G1"},
-                    {Pos = "Pos8",  TcPos = "T9",  Head = "H11", Group = "G1"},
+                    {Pos = "Pos8",  TcPos = "T9",  Head = EgtIf( AggreBH, "H17", "H11"), Group = "G1"},
                     {Pos = "Pos9",  TcPos = "T10", Head = "H11", Group = "G1"},
                     {Pos = "Pos10",  TcPos = "T11", Head = "H22", Group = "G3"},
                     {Pos = "Pos11",  TcPos = "T13", Head = "H21", Group = "G3"},
@@ -61,7 +62,7 @@ else
                     {Pos = "Pos5",  TcPos = "T6",  Head = "H11", Group = "G1"},
                     {Pos = "Pos6",  TcPos = "T7",  Head = "H11", Group = "G1"},
                     {Pos = "Pos7",  TcPos = "T8",  Head = "H11", Group = "G1"},
-                    {Pos = "Pos8",  TcPos = "T9",  Head = "H11", Group = "G1"},
+                    {Pos = "Pos8",  TcPos = "T9",  Head = EgtIf( AggreBH, "H17", "H11"), Group = "G1"},
                     {Pos = "Pos9",  TcPos = "T10", Head = "H11", Group = "G1"},
                     {Pos = "Pos10",  TcPos = "T11", Head = "H21", Group = "G3"},
                     {Pos = "Pos11",  TcPos = "T12", Head = "H21", Group = "G3"},
@@ -78,7 +79,7 @@ else
       table.insert( PositionTable, {Pos = "Pos21", TcPos = "T201", Head = "H13", Group = "G2"})
    end
 end
-local UsePositionHead = true
+local UsePositionHead = false
 
 local function IsInGeomSet( ToolHead, PosHead)
    for GsIndex = 1, #GS do

UpdateLog.txt

@@ -1,5 +1,32 @@
            ==== Common_ONE-PF Update Log ====
 
+Versione 2.7k3 (28/11/2025)
+- (GEN) Prima di andare allo scarico, si aggiunge movimento intermedio dove si aspetta che rulli scarico siano arrivati in posizione. Ticket#2716
+
+Versione 2.7k2 (20/11/2025)
+- (SIM) Aggiornata risoluzione VMillTol in funzione dello spessore lama
+
+Versione 2.7k1 (05/11/2025)
+- (SIM-GEN) Corretto calcolo per decidere se serve aprire i rulli
+- (GEN) Aggiunta tolleranza in creazione piano di lavoro inclinato
+- (SIM) Allo scarico si resetta Y2DELTA. Ticket#2687
+
+Versione 2.7j3 (23/10/2025)
+- (SIM) Corretta posizione parcheggio in caso di testa 1 su magazzino 2. Ticket#2660
+
+Versione 2.7j2 (21/10/2025)
+- (GEN) Se SPLIT con pinza 5, corretto salvataggio posizione pinza 2. Ticket#2654
+
+Versione 2.7j1 (08/10/2025)
+- (GEN) Salvataggio posizione Z su lavorazione precedente, sbagliava in caso di separazione. Ticket#2637
+
+Versione 2.7i1 (10/09/2025)
+- (SIM-GEN) Piccole correzioni per gestire secondo TC su ONE. Ticket#2563
+- (SIM-GEN) Gestione aggregato BH completato. Ticket#2482
+- (EST) Stima tempi considerando accelerazioni
+- (SIM-GEN) Se fase start o restart, si aggiorna la posizione in X dell'asse per calcolare il link corretto
+- (GEN) Piccola correzione risalita ZMAX dopo RELOAD del pezzo. Generazione allineata a simulazione.
+
 Versione 2.7h2 (28/08/2025)
 - (GEN) Migliorata gestione spegnimento utensile e disattivazione piano
 - (SIM-GEN) Corretto nome variabile e altre piccole modifiche per Progress

Version.lua

@@ -3,7 +3,7 @@
 
 local InfoCommon_STD_PP = {
    NAME = 'Common_ONE-PF',            -- nome script PP standard
-   VERSION = '2.7h2',                 -- versione script
+   VERSION = '2.7k3',                 -- versione script
    MIN_MACH_VER_PP_COMMON = '2.5k1'   -- versione minima kernel
 }