Allineamento con common ver. 2.7a1

- In GetZExtra contemplato anche casi sotto-squadra

Common_ONE-PF.NUM.mlpe

@@ -878,15 +878,13 @@ function OnRapid()
                if  EMT.HEAD == 'H12'  and  EMT.L2 < -LimX1PlRotSaw  then
                   dXref = -LimX1PlRotSaw
                   EmitMoveDataHead( 1, { X=dXref, Z=MyMaxZ1, B=ParkB1, C=ParkC1, S=Speed})
-                  if bMoveZbeforeX then
-                     dZref = min( dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2), MyMaxZ1)
-                  end
+                  dZref = max( EMT.L3, dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2))
                   dMoveXtoFinalPosition = true
                elseif not bMoveZbeforeX then
                   EmitMoveDataHead( 1, { X=dXref, Z=MyMaxZ1, B=ParkB1, C=ParkC1, S=Speed})
                else
                   EmitMoveDataHead( 1, { X=-LimX1PlRotSaw, Z=MyMaxZ1, B=ParkB1, C=ParkC1, S=Speed})
-                  dZref = min( dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2), MyMaxZ1)
+                  dZref = max( EMT.L3, dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2))
                   dMoveXtoFinalPosition = true
                end
    
@@ -1249,15 +1247,13 @@ function OnRapid()
                   if  EMT.HEAD == 'H12'  and  EMT.L2 < -LimX1PlRotSaw  then
                      dXref = -LimX1PlRotSaw
                      EmitMoveDataHead( 1, { X=dXref, Z=CurrZ1, B=CurrB1, C=CurrC1, TRad=dTRad, TLen=dTLen, S=Speed})
-                     if bMoveZbeforeX then
-                        dZref = min( dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2), MyMaxZ1)
-                     end
+                     dZref = max( EMT.L3, dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2))
                      dMoveXtoFinalPosition = true
                   elseif not bMoveZbeforeX then
                      EmitMoveDataHead( 1, { X=dXref, Z=CurrZ1, B=CurrB1, C=CurrC1, TRad=dTRad, TLen=dTLen, S=Speed})
                   else
                      EmitMoveDataHead( 1, { X=CurrX1, Z=CurrZ1, B=CurrB1, C=CurrC1, TRad=dTRad, TLen=dTLen, S=Speed})
-                     dZref = min( dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2), MyMaxZ1)
+                     dZref = max( EMT.L3, dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2))
                      dMoveXtoFinalPosition = true
                   end
 
@@ -2263,7 +2259,7 @@ function PreparePreRotation( sCmd, nInd)
             MDChar = { Y2=ParkY2, V2=ParkV2, IniStatY2=1, FinStatY2=1, BeamVise=0}
             table.insert( EMT.MDCHAR, MDChar)
             MDChar = { [Cmd[2]]=tonumber(Cmd[3]), IniStatY1=86, FinStatY1=87, BeamVise=0}
-         elseif EMT.SPECSPLIT then
+         elseif EMT.SPECSPLIT or EMT.SPLITROT then
             MDChar = { [Cmd[2]]=tonumber(Cmd[3]), V1=ParkV1, IniStatY1=EMT.ISY1, FinStatY1=EMT.FSY1, IniStatY2=EMT.ISY2, FinStatY2=EMT.FSY2, IniStatV1=3, BeamVise=EMT.BV}
             EMT.V1POS = MDChar.V1
          else
@@ -2727,7 +2723,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
          if not HeadIsChainSaw( EMT.HEAD) then
             -- eseguo la salita a Z1max (oriento solo se assi rotanti non già a posto)
             if abs( dSafeC1 - PrevR1) > 0.1 or abs( dSafeB1 - PrevR2) > 0.1 then
-               local dZref = dSafeZ1 + GetZExtra( EMT.HEAD, PrevR2)
+               local dZref = dSafeZ1 + GetZExtra( EMT.HEAD, EgtClamp( PrevR2, -90, 90))
                if EgtIf( BD.RIGHT_LOAD, -dXPos < -LimX1RotSaw, -dXPos > -LimX1RotSaw) then
                   dZref = dZref - EgtIf( not Mortiser, 100, 370)
                end
@@ -2966,17 +2962,27 @@ function EmitParkRoller( dPosT, bSplitCut, bUsePrevDelta)
       local DiffY2 = MyParkY2 - dPosY2
       --EmtOutput( string.format( 'PosT=%.3f DiffY1=%.3f DiffY2=%.3f', dPosT, DiffY1, DiffY2))
       if bSplitCut then
+         local bYNoMove, bVNoMove
          if DiffY1 > 0.1  then
+            bYNoMove = false
             MDChar.Y1 = dPosY1 + DiffY1
          else
+            bYNoMove = true
             MDChar.Y1 = dPosY1
          end
          if DiffY2 < -0.1 then
+            bVNoMove = false
             MDChar.Y2 = dPosY2 + DiffY2
             dPosT = dPosT + DiffY2
          else
+            bVNoMove = true
             MDChar.Y2 = dPosY2
          end
+         -- se entrambe le morse sono restate in posizione, le sposto comunque di 5mm per distanziare i pezzi separati
+         if bYNoMove and bVNoMove then
+            MDChar.Y1 = MDChar.Y1 + 5
+            MDChar.Y2 = MDChar.Y2 - 5
+         end
       elseif DiffY1 > 0.1 and DiffY2 < -0.1 then
          EmtSetLastError( 1201, 'Error Collision in ParkRoller')
       elseif DiffY1 > 0.1  then

Common_ONE-PF.mlpe

@@ -1011,15 +1011,13 @@ function OnSimulMoveStart()
                if  EMT.HEAD == 'H12' and  -EMT.L2 < -LimX1PlRotSaw  then
                   dXref = LimX1PlRotSaw
                   SimulMoveAxis( 'X1', dXref, MCH_SIM_STEP.RAPID)
-                  if bMoveZbeforeX then
-                     dZref = Z1Home + GetZExtra( EMT.HEAD, EMT.R2)
-                  end
+                  dZref = max( EMT.L3, Z1Home + GetZExtra( EMT.HEAD, EMT.R2))
                   dMoveXtoFinalPosition = true
                elseif not bMoveZbeforeX then
                   SimulMoveAxis( 'X1', dXref, MCH_SIM_STEP.RAPID)
                else
                   SimulMoveAxis( 'X1', LimX1PlRotSaw, MCH_SIM_STEP.RAPID)
-                  dZref = Z1Home + GetZExtra( EMT.HEAD, EMT.R2)
+                  dZref = max( EMT.L3, Z1Home + GetZExtra( EMT.HEAD, EMT.R2))
                   dMoveXtoFinalPosition = true
                end
 
@@ -1621,7 +1619,7 @@ function ExecMoveZmax( bMchSplit, btoXHome)
       if GetHeadTCSet( EMT.HEAD, EMT.TCPOS) == 'Head1_TC1' then
          if not HeadIsChainSaw( EMT.HEAD) then
             if abs( HomeC - CurrC) > 0.1 or abs( HomeB - CurrB) > 0.1 then
-               local dZref = HomeZ + GetZExtra( EMT.HEAD, CurrB)
+               local dZref = HomeZ + GetZExtra( EMT.HEAD, EgtClamp( CurrB, -90, 90))
                if EgtIf( BD.RIGHT_LOAD, -CurrX < -LimX1RotSaw, -CurrX > -LimX1RotSaw) then
                   dZref = dZref - EgtIf( not Mortiser, 100, 370)
                end
@@ -1846,8 +1844,16 @@ function ExecParkRoller( PosY1, PosY2, PosV1, PosV2, bSpliCut, bAgg)
       local DiffY2 = MyParkY2 - PosY2
       -- se appena eseguito taglio di separazione
       if bSpliCut then
-         local MoveY1 = max( DiffY1, 0.0)
-         local MoveY2 = min( DiffY2, 0.0)
+         -- se entrambe le morse sono restate in posizione, le sposto comunque di 5mm per distanziare i pezzi separati
+         local dAddMove
+         if DiffY1 > 0.1 and DiffY2 < -0.1 then
+            dAddMove = 0
+         else
+            dAddMove = 5
+         end
+         local MoveY1 = max( DiffY1, 0.0 + dAddMove)
+         local MoveY2 = min( DiffY2, 0.0 - dAddMove)
+
          -- aggancio i pezzi rimanenti all'asse Y1
          LinkRemainingPartsToY1()
          -- eseguo i movimenti

Common_ONE-PF.mlse

@@ -73,7 +73,7 @@ function OnSpecialGetMaxZ()
          EMC.MAXZ = ParkZ1 + CalcExtraZ( vtTpZm, vtT, vMZ)
       end
    elseif EMC.HEAD == 'H12' and sHead_TC == 'Head1_TC1' then
-      if vtTp:getX() > 0.3 and vtT:getX() > 0.3 then
+      if vtTp:getX() > 0.4 and vtT:getX() > 0.4 then
          if bBSameSign and abs( EMC.R1 - EMC.R1p) < 165 then
             EMC.MAXZ = MaxZ1 - EgtIf( abs( EMC.R2) < 90.1 and abs( EMC.R2p) < 90.1, 0, 130)
          elseif vtTp:getZ() > 0.707 or vtT:getZ() > 0.707 then
@@ -95,7 +95,7 @@ function OnSpecialGetMaxZ()
          EMC.MAXZ = ParkZ1 + CalcExtraZ( vtTpZm, vtT, vMZ)
       end
    elseif EMC.HEAD == 'H12' and sHead_TC == 'Head1_TC2' then
-      if vtTp:getX() > 0.3 and vtT:getX() > 0.3 then
+      if vtTp:getX() > 0.4 and vtT:getX() > 0.4 then
          if bBSameSign and abs( EMC.R1 - EMC.R1p) < 165 then
             EMC.MAXZ = MaxZ1 - EgtIf( abs( EMC.R2) < 90.1 and abs( EMC.R2p) < 90.1, 0, 130)
          elseif vtTp:getZ() > 0.707 or vtT:getZ() > 0.707 then
@@ -124,7 +124,7 @@ function OnSpecialGetMaxZ()
          EMC.MAXZ = ParkZ2 + CalcExtraZ( vtTpZm, vtT, vMZ)
       end
    elseif EMC.HEAD == 'H22' then
-      if vtTp:getX() > 0.3 and vtT:getX() > 0.3 then
+      if vtTp:getX() > 0.4 and vtT:getX() > 0.4 then
          if bBSameSign and abs( EMC.R1 - EMC.R1p) < 165 then
             EMC.MAXZ = MaxZ2 - EgtIf( abs( EMC.R2) < 90.1 and abs( EMC.R2p) < 90.1, 0, 130)
          elseif vtTp:getZ() > 0.707 or vtT:getZ() > 0.707 then

Essetre-PF.mlde

@@ -32,8 +32,8 @@
 require( 'EmtGenerator')
 EgtEnableDebug( false)
 
-PP_VER = '2.6l1'
-PP_NVER = '2.6.12.1'
+PP_VER = '2.7a1'
+PP_NVER = '2.7.1.1'
 MIN_MACH_VER = '2.5k1'
 MACH_NAME = 'Essetre-PF'
 
@@ -878,7 +878,7 @@ end
 
 ---------------------------------------------------------------------
 function GetHeadSet( sHead)
-   if sHead == 'H11' or sHead == 'H12' then
+   if sHead == 'H11' or sHead == 'H12' or sHead == 'H13' or sHead == 'H15' then
       return 1
    elseif sHead == 'H21' or sHead == 'H22' or sHead == 'H23' then
       return 2
@@ -964,7 +964,7 @@ function GetZExtra( sHead, dAngV)
       elseif abs( dAngV) < 60.1 then
          return 200
       elseif abs( dAngV) < 90.1 then
-         return 10
+         return 1
       else
          return 0
       end
@@ -976,7 +976,9 @@ function GetZExtra( sHead, dAngV)
       elseif abs( dAngV) < 60.1 then
          return 200
       elseif abs( dAngV) < 90.1 then
-         return 10
+         return 1
+      elseif abs( dAngV) < 120 then
+         return -100
       else
          return 0
       end

UpdateLog.txt

@@ -1,5 +1,13 @@
            ==== Common_ONE-PF Update Log ====
 
+Versione 2.7a1 (07/01/2024)
+- (GEN) In separazione, quando si porta indietro il restante, si aprono le paratie rulli subito. Ticket#2214
+- (SIM-GEN) Se entrambe le morse sono restate in posizione, le sposto comunque di 5mm per distanziare i pezzi separati. Ticket#2206
+
+Versione 2.6l2 (09/12/2024)
+- (SIM-GEN) Corretto problema introdotto in 2.6l1 per risolvere #2198. Ticket#2203
+- (SIM-GEN) In MLSE modificato controllo direzione utensile per determinare Z massima. Ticket#2204
+
 Versione 2.6l1 (02/12/2024)
 - (SIM) Dopo scarico pezzo per ribaltamento, si aprono sempre i rulli. Ticket#2192
 - (SIM-GEN) Nei movimenti si ricalcola la Z solo se la quota di lavoro è più in alta della posizione a ZHOME della testa. Ticket#2198

Version.lua

@@ -3,7 +3,7 @@
 
 local InfoCommon_STD_PP = {
    NAME = 'Common_ONE-PF',            -- nome script PP standard
-   VERSION = '2.6l1',                 -- versione script
+   VERSION = '2.7a1',                 -- versione script
    MIN_MACH_VER_PP_COMMON = '2.5k1'   -- versione minima kernel
 }