Allineamento a common ver. 3.1a2

- HOTFIX: DeltaTol spostato in MLDE

.gitignore

@@ -1,6 +1,7 @@
 /Tools
 /Machinings
 /SetUp
+/Beam/AISetup
 /Beam/Ts3Data.bak
 /Beam/CutData.lua
 /Beam/DrillData.lua

Beam/BeamData.lua

@@ -6,9 +6,9 @@ EgtOutLog( ' FAST-BeamData started', 1)
 
 -- Tabella per definizione modulo
 local BeamData = {
-   RIGHT_LOAD = true,                       -- flag carico da destra
    SIMUL_VIEW_DIR = 1,                      -- direzione di vista predefinita per la simulazione (1=NW, 2=SW, 3=NE, 4=SE)
    GO_FAST = 0,                             -- flag abilitazione modalità veloce (0=no, 1=carrelli, 2=anche cambio utensili)
+   RIGHT_LOAD = true,                       -- flag carico da destra
    ROT90 = false,                           -- flag abilitazione rotazione 90 gradi
    ROT180 = true,                           -- flag abilitazione rotazione 180 gradi
    NEWCLAMPING = false,                     -- flag abilitazione nuovo metodo riposizionamento carrelli
@@ -107,6 +107,9 @@ if EgtExistsFile( sData) then
          BeamData.ADVANCE_TAIL_OFFS = Machine.Offsets.ADVANCE_TAIL_OFFS or BeamData.ADVANCE_TAIL_OFFS
          BeamData.LEN_VERY_SHORT_PART = Machine.Offsets.LEN_VERY_SHORT_PART or BeamData.LEN_VERY_SHORT_PART
          BeamData.LEN_SHORT_PART = Machine.Offsets.LEN_SHORT_PART or BeamData.LEN_SHORT_PART
+         BeamData.MAX_DIM_HTCUT_HBEAM = Machine.Offsets.MAX_DIM_HTCUT_HBEAM or BeamData.MAX_DIM_HTCUT_HBEAM
+         BeamData.MAX_HEIGHT2 = Machine.Offsets.MAX_HEIGHT2 or BeamData.MAX_HEIGHT2
+         BeamData.OVM_MID = Machine.Offsets.OVM_MID or BeamData.OVM_MID
          if Machine.Offsets.PRECUT_HEAD_DISABLE then BeamData.PRECUT_HEAD = ( Machine.Offsets.PRECUT_HEAD_DISABLE == 0) end
          if Machine.Offsets.PRECUT_TAIL_DISABLE then BeamData.PRECUT_TAIL = ( Machine.Offsets.PRECUT_TAIL_DISABLE == 0) end
          if Machine.Offsets.MIN_HEIGHT_ADDED_CUTS then BeamData.MIN_HEIGHT_ADDED_CUTS = min( Machine.Offsets.MIN_HEIGHT_ADDED_CUTS, BeamData.MIN_HEIGHT_ADDED_CUTS) end
@@ -114,6 +117,8 @@ if EgtExistsFile( sData) then
          if Machine.Offsets.FASTCLAMPING ~= nil then BeamData.FASTCLAMPING = ( Machine.Offsets.FASTCLAMPING == 1) end
          if Machine.Offsets.ROT90 ~= nil then BeamData.ROT90 = ( Machine.Offsets.ROT90 == 1) end
          if Machine.Offsets.ROT180 ~= nil then BeamData.ROT180 = ( Machine.Offsets.ROT180 == 1) end
+         if Machine.Offsets.CUT_SIC then BeamData.CUT_SIC = EgtClamp( Machine.Offsets.CUT_SIC, 15, 50) end
+         
       end
       if Machine.Trave then
          BeamData.MIN_WIDTH = Machine.Trave.XMIN or BeamData.MIN_WIDTH
@@ -178,10 +183,10 @@ BeamData.GetBlockedAxis = GetBlockedAxis
 
 ---------------------------------------------------------------------
 local function GetChainSawInitAngs( vtN, vtO, nInd)
-   if nInd == 1 then
-      return ''
+   if vtN:getY() > 0 and vtO:getX() > 0 then
+      return 'C=0'
    else
-      return EgtIf( vtN:getY() > 0, 'C=180', 'C=-180')
+      return ''
    end
 end
 BeamData.GetChainSawInitAngs = GetChainSawInitAngs

Beam/MachiningTypes.ini

@@ -4,9 +4,11 @@
 
 [Drill]
 1=Drill
-2=Pocket
-3=AngleDrill
-4=Predrill
+2=Drill_AT
+3=Pocket
+4=Pocket_AT
+5=AngleDrill
+6=Predrill
 
 [Milling]
 1=Prof
@@ -14,25 +16,33 @@
 3=Tenon
 4=DtTenon
 5=DtMortise
-6=BirdsMouth
-7=Chamfer
-8=Mark
-9=Text
-10=Decor01
-11=Long2Cut
-12=Long2CutDown
-13=LongSmallCut
-14=BHSideMill
-15=CleanCorner
-16=ProfTCone
-17=Long2CutSide
-18=SmallToolContour
-19=AntiSplintMillCut
+6=DtMortise_AT
+7=BirdsMouth
+8=Chamfer
+9=Mark
+10=Text
+11=Text_AT
+12=Decor01
+13=Long2Cut
+14=Long2CutDown
+15=LongSmallCut
+16=BHSideMill
+17=CleanCorner
+18=ProfTCone
+19=Long2CutSide
+20=SmallToolContour
+21=AntiSplintMillCut
+22=Prof_end
+23=SideMillAsBlade
+24=FloatingAggregate
 
 [Pocketing]
 1=Pocket
-2=OpenPocket
-3=Mortise
+2=Pocket_AT
+3=OpenPocket
+4=OpenPocket_AT
+5=Mortise
+6=Mortise_AT
 
 [Sawing]
 1=Sawing

Common_FAST.NUM.mlpe

@@ -6,7 +6,7 @@ local INFO_STD_PP = require( 'Version')
 local BD = require( 'BeamData')
 
 -- Variabili di modulo
-local CSP_INFO =     INFO_STD_PP.NAME..'  ver.'..INFO_STD_PP.VERSION..' by EgalWare s.r.l.'
+local CSP_INFO =     INFO_STD_PP.NAME..'_'..NumericalControl..'  ver.'..INFO_STD_PP.VERSION..' by EgalWare s.r.l.'
 local MACHINE_INFO = MACH_NAME..'  ver.'..PP_VER
 local TEST_USE = false
 
@@ -27,7 +27,9 @@ function OnStart()
    --EMT.LINEINC = 1        -- incremento numerazione linee
    --EMT.Ft = 'F'           -- token per feed
    --EMT.St = 'S'           -- token per speed
-   EMT.FMAXPINZE = 154000 -- feed massima pinze
+   EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+   EMT.MAXACC = MaxAcc or ( EMT.FMAXPINZE / ( 60 * 0.3))  -- accelerazione massima pinze
+   EMT.MINACC = MinAcc or ( EMT.FMAXPINZE / ( 60 * 4))    -- accelerazione minima pinze
 end
 
 ---------------------------------------------------------------------
@@ -53,6 +55,7 @@ function OnProgramStart()
    end
    EmtOutput( sPrefixCommentLine..'('.. CSP_INFO..')')
    EmtOutput( sPrefixCommentLine..'('.. MACHINE_INFO..')\n')
+   EmtOutput( '(HEADER)')
    -- Se modalità test, aggiungo linee per muovere tappeto e alzare la testa (in automatico viene fatto dal main residente)
    if TEST_USE then
       EmtOutput( 'M28')
@@ -104,6 +107,7 @@ function OnProgramEnd()
    EMT.FALL = nil
    EMT.RELOAD = nil
    EMT.RELOAD2 = nil
+   EmtOutput( '(FOOTER)')
    -- Se modalità test, termino il programma
    if TEST_USE then
       EmtOutput( 'M02')
@@ -181,16 +185,12 @@ function OnDispositionEnd()
       local STrave = EMT.ST
       local HOverM = EMT.HOVM
       -- calcolo dati pinze
-      local MinAccPinze = 0.3
-      local MaxAccPinze = 4
       local KgMtCubo= WoodDensity or 550           -- densità legno in Kg / metro cubo
       local Massa = ( HTrave * STrave * LBarra * KgMtCubo ) / 1000000000
       local FMaxPinze = EMT.FMAXPINZE
       local ForzaAtrito = 700 / 2   -- Serve per regolare P32 (700 valore reale pistone)
       local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAtrito) / 1000)
-      if ( TempoAcc < MinAccPinze) then TempoAcc = MinAccPinze end
-      if ( TempoAcc > MaxAccPinze) then TempoAcc = MaxAccPinze end
-      local AccPinze = FMaxPinze / ( 60 * TempoAcc)
+      local AccPinze = EgtClamp( FMaxPinze / ( 60 * TempoAcc), EMT.MINACC, EMT.MAXACC)
       local RidFeed = 100 / Massa * 100
       if ( RidFeed > 100) then RidFeed = 100 end
       if IdTrave >= 0 then
@@ -250,9 +250,9 @@ function OnDispositionEnd()
          EmtOutput( sOut)
       -- altrimenti recupero rimanenza   
       else
-         EmtOutput( 'G112 EC1'..' Y'..EmtLenToString( LoadT, 3).. ' EY'..EmtLenToString( EMT.YPOS, 3)..' EV'..EmtLenToString( ParkV, 3) ..' EF'..GetFmaxClamp())
+         EmtOutput( 'G112 EC1'..' Y'..EmtLenToString( EMT.TPOS, 3).. ' EY'..EmtLenToString( EMT.YPOS, 3)..' EV'..EmtLenToString( ParkV, 3) ..' EF'..GetFmaxClamp())
          -- aggiorno dati aggancio carrelli alla trave
-         EMT.YDELTA = EMT.YPOS - LoadT
+         EMT.YDELTA = EMT.YPOS - EMT.TPOS
          EMT.VDELTA = nil
       end
       -- eventuale preparazione per rotazione immediata
@@ -496,6 +496,7 @@ function OnMachiningEnd()
    EMT.U_STD = nil
    EMT.PREVTOOL = EMT.TOOL
    EMT.PREVHEAD = EMT.HEAD
+   EMT.PREVET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
 end
 
 ---------------------------------------------------------------------
@@ -608,6 +609,9 @@ function OnRapid()
    MyBackupAxes()
    -- se primo movimento della lavorazione, gestione speciale
    if EMT.MCHFIRST and not EMT.OPEISDISP then
+      -- primo posizionamento
+      local MyZHome = EgtGetAxisHomePos( 'Z')
+      local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or  EMT.L3 > -1)
       -- decido se muovere prima testa o carrelli (standard prima testa)
       local bHeadFirst = true
       local sLateG101
@@ -626,15 +630,29 @@ function OnRapid()
          end
       end
 
-      -- primo posizionamento
-      local MyZHome = EgtGetAxisHomePos( 'Z')
-      local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or  EMT.L3 > -1)
+      local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
+
+      local bGoToHome = false
+      -- se gli assi rotanti cambiano parecchio, con motosega si va in parcheggio 
+      if EMT.PREVHEAD == 'H3' and EMT.HEAD == 'H3' and sET == EMT.PREVET and ( abs( EMT.R2pp - EMT.R2) > 25 or abs( EMT.R1pp - EMT.R1) > 25)  then
+         bGoToHome = true
+      end
+
+      -- ricavo i dati per la lavorazione
+      local sEE = ' EE' .. EgtIf( bZmax, '3', '4')
+      local sEL = ' EL' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TLEN, ( EMT.TDIST or ChSawLen)), 3)
+      local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
+      local sES = ' ES'..EgtNumToString( EMT.S, 0)
+
       -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-      if EMT.PREVHEAD == 'H3' and EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
+      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.FLAG2 == 1 then
          local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
                                        ' B' .. EmtLenToString( EMT.R2pp, 3) .. ' C' .. EmtLenToString( EMT.R1pp, 3) .. 
                                        ' EE' .. EgtIf( bZmax, '3', '4') .. EMT.PREVsEL .. EMT.PREVsER .. EMT.PREVsET .. EMT.PREVsES
          EmtOutput( sOutPreMove)
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1pp, 3) .. sEE .. sEL .. sER .. sET .. sES
+         EmtOutput( sOutPreMove)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
       end
@@ -644,18 +662,21 @@ function OnRapid()
          EmtOutput( '( *** ' .. sOut .. ' *** )')
       end
 
-      -- ricavo i dati per la lavorazione
-      local sEE = ' EE' .. EgtIf( bZmax, '3', '4')
-      local sEL = ' EL' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TLEN, ( EMT.TDIST or ChSawLen)), 3)
-      local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
-      local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
-      local sES = ' ES'..EgtNumToString( EMT.S, 0)
-
       -- se carico motosega, ruoto in zona sicura prima di approcciare la lavorazione
-      if ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
+      if not EMT.LOAD and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and
+         ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
          local sEEPreMove = ' EE' .. EgtIf( bZmax, '3', '4')
-         local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
-                                       EmtGetAxis( 'R2') .. EmtGetAxis( 'R1') .. sEE .. sEL .. sER .. sET .. sES
+         local sOutPreMove
+         if EMT.HEAD == 'H3' and bGoToHome then
+            sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1pp, 3) .. sEE .. sEL .. sER .. sET .. sES
+            EmtOutput( sOutPreMove)
+            sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
+            EmtOutput( sOutPreMove)
+         end
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( EMT.R2, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
          EmtOutput( sOutPreMove)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
@@ -845,13 +866,13 @@ function OnRapid()
          local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
          local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
          local sES = ' ES'..EgtNumToString( EMT.S, 0)
-         local sOut = 'G101' .. EmtGetAxis( 'L2') .. EmtGetAxis( 'L3') ..' B=' .. EgtNumToString( dBAxis, 3) ..
-                      ' C=' .. EgtNumToString( dCAxis, 3) .. sEE .. sEL .. sER .. sET .. sES
+         local sOut = 'G101' .. EmtGetAxis( 'L2') .. EmtGetAxis( 'L3') ..' B' .. EgtNumToString( dBAxis, 3) ..
+                      ' C' .. EgtNumToString( dCAxis, 3) .. sEE .. sEL .. sER .. sET .. sES
          EmtOutput( sOut)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
-         sOut = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. EmtGetAxis( 'L3') ..' B=' .. EgtNumToString( dBAxis, 3) ..
-                ' C=' .. EgtNumToString( dCAxis, 3) .. sEE .. sEL .. sER .. sET .. sES
+         sOut = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. EmtGetAxis( 'L3') ..' B' .. EgtNumToString( dBAxis, 3) ..
+                ' C' .. EgtNumToString( dCAxis, 3) .. sEE .. sEL .. sER .. sET .. sES
          EmtOutput( sOut)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
@@ -1538,7 +1559,7 @@ function MyAdjustLinearAxes()
       elseif EMT.HEAD ~= 'H3' then
          local Len = EMT.TLEN + EgtIf( EMT.HEAD == 'H1', MillOffs, abs( SawOffs))
          local LenRef = MillOffs
-         vtE = Vector3d( EMT.EXTR) * Len - Z_AX() * LenRef
+         vtE = Vector3d( EMT.TDIR) * Len - Z_AX() * LenRef
       else
          local LenAux = ( EMT.TDIST or ChSawLen) + MillOffs
          local LenRef = MillOffs

Common_FAST.NUM_PLUS.mlpe

@@ -6,7 +6,7 @@ local INFO_STD_PP = require( 'Version')
 local BD = require( 'BeamData')
 
 -- Variabili di modulo
-local CSP_INFO =     INFO_STD_PP.NAME..'  ver.'..INFO_STD_PP.VERSION..' by EgalWare s.r.l.'
+local CSP_INFO =     INFO_STD_PP.NAME..'_'..NumericalControl..'  ver.'..INFO_STD_PP.VERSION..' by EgalWare s.r.l.'
 local MACHINE_INFO = MACH_NAME..'  ver.'..PP_VER
 local TEST_USE = false
 
@@ -27,7 +27,9 @@ function OnStart()
    --EMT.LINEINC = 1        -- incremento numerazione linee
    --EMT.Ft = 'F'           -- token per feed
    --EMT.St = 'S'           -- token per speed
-   EMT.FMAXPINZE = 154000 -- feed massima pinze
+   EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+   EMT.MAXACC = MaxAcc or ( EMT.FMAXPINZE / ( 60 * 0.3))  -- accelerazione massima pinze
+   EMT.MINACC = MinAcc or ( EMT.FMAXPINZE / ( 60 * 4))    -- accelerazione minima pinze
 end
 
 ---------------------------------------------------------------------
@@ -53,6 +55,7 @@ function OnProgramStart()
    end
    EmtOutput( sPrefixCommentLine..'('.. CSP_INFO..')')
    EmtOutput( sPrefixCommentLine..'('.. MACHINE_INFO..')\n')
+   EmtOutput( '(HEADER)')
    -- Se modalità test, aggiungo linee per muovere tappeto e alzare la testa (in automatico viene fatto dal main residente)
    if TEST_USE then
       EmtOutput( 'M28')
@@ -108,6 +111,7 @@ function OnProgramEnd()
    EMT.FALL = nil
    EMT.RELOAD = nil
    EMT.RELOAD2 = nil
+   EmtOutput( '(FOOTER)')
    -- Se modalità test, termino il programma
    if TEST_USE then
       EmtOutput( 'M02')
@@ -203,9 +207,9 @@ function OnDispositionEnd()
       local BtlInfoId = EgtGetFirstNameInGroup( GDB_ID.ROOT, 'BtlInfo') or EgtGetCurrMachGroup() or GDB_ID.NULL
       local nLoad90 = EgtGetInfo( BtlInfoId, 'LOAD90', 'i') or 0
       -- calcolo dati pinze
-      local AccPinze, AccMaxPinze, RidFeed, TempoAcc = CalcDinamicaPinze( HTrave, STrave, LBarra)
-      local AccPinz1, AccMaxPinz1, RidFeed1, TempoAcc1 = CalcDinamicaPinze( HTrave, STrave, LBarra - LTrave)
-      local AccPinz2, AccMaxPinz2, RidFeed2, TempoAcc2 = CalcDinamicaPinze( HTrave, STrave, LTrave)
+      local AccPinze, AccMaxPinze, RidFeed, TempoAcc = CalcDinamicaPinze_NUM( HTrave, STrave, LBarra)
+      local AccPinz1, AccMaxPinz1, RidFeed1, TempoAcc1 = CalcDinamicaPinze_NUM( HTrave, STrave, LBarra - LTrave)
+      local AccPinz2, AccMaxPinz2, RidFeed2, TempoAcc2 = CalcDinamicaPinze_NUM( HTrave, STrave, LTrave)
       if IdTrave >= 0 then
          local sOut = '( SN='..IdTrave..' LBarra='..EmtLenToString( LBarra, 3)..' L='..EmtLenToString( LTrave, 3)..
                       ' H='..EmtLenToString( HTrave, 3)..' S='..EmtLenToString( STrave, 3)..' Acc='..EgtNumToString( TempoAcc, 1)..
@@ -269,9 +273,9 @@ function OnDispositionEnd()
          EmtOutput( sOut)
       -- altrimenti recupero rimanenza   
       else
-         EmtOutput( 'G112 EC1'..' Y'..EmtLenToString( LoadT, 3).. ' EY'..EmtLenToString( EMT.YPOS, 3)..' EV'..EmtLenToString( ParkV, 3) ..' EF'..GetFmaxClamp())
+         EmtOutput( 'G112 EC1'..' Y'..EmtLenToString( EMT.TPOS, 3).. ' EY'..EmtLenToString( EMT.YPOS, 3)..' EV'..EmtLenToString( ParkV, 3) ..' EF'..GetFmaxClamp())
          -- aggiorno dati aggancio carrelli alla trave
-         EMT.YDELTA = EMT.YPOS - LoadT
+         EMT.YDELTA = EMT.YPOS - EMT.TPOS
          EMT.VDELTA = nil
       end
       -- eventuale preparazione per rotazione immediata
@@ -540,6 +544,7 @@ function OnMachiningEnd()
    EMT.PREVTOOL = EMT.TOOL
    EMT.PREVHEAD = EMT.HEAD
    EMT.PREVR3 = EMT.R3
+   EMT.PREVET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
 end
 
 ---------------------------------------------------------------------
@@ -652,6 +657,9 @@ function OnRapid()
    MyBackupAxes()
    -- se primo movimento della lavorazione, gestione speciale
    if EMT.MCHFIRST and not EMT.OPEISDISP then
+      -- primo posizionamento
+      local MyZHome = EgtGetAxisHomePos( 'Z')
+      local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or  EMT.L3 > -1)
       -- decido se muovere prima testa o carrelli (standard prima testa)
       local bHeadFirst = true
       local sLateG101
@@ -671,22 +679,12 @@ function OnRapid()
          end
       end
 
-      -- primo posizionamento
-      local MyZHome = EgtGetAxisHomePos( 'Z')
-      local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or  EMT.L3 > -1)
-      -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-      if EMT.PREVHEAD == 'H3' and EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
-         local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
-                                       ' B' .. EmtLenToString( EMT.R2pp, 3) .. ' C' .. EmtLenToString( EMT.R1pp, 3) .. 
-                                       ' EE' .. EgtIf( bZmax, '3', '4') .. EMT.PREVsEL .. EMT.PREVsER .. EMT.PREVsET .. EMT.PREVsES
-         EmtOutput( sOutPreMove)
-         EmtOutput( 'G101 ET1001')
-         EmtOutput( 'G101 ET2001')
-      end
+      local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
 
-      if not EMT.LOAD then
-         local sOut = string.gsub( string.gsub( EMT.MCHNAME..'/'..EMT.TOOL, '%(', '-'), '%)', '-')
-         EmtOutput( '( *** ' .. sOut .. ' *** )')
+      local bGoToHome = false
+      -- se gli assi rotanti cambiano parecchio, con motosega si va in parcheggio 
+      if EMT.PREVHEAD == 'H3' and EMT.HEAD == 'H3' and sET == EMT.PREVET and ( abs( EMT.R2pp - EMT.R2) > 25 or abs( EMT.R1pp - EMT.R1) > 25)  then
+         bGoToHome = true
       end
 
       -- ricavo i dati per la lavorazione
@@ -716,14 +714,41 @@ function OnRapid()
          sER = sER..EmtLenToString( EMT.TDIAM / 2, 3)
       end
 
-      local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
       local sES = ' ES'..EgtNumToString( EMT.S, 0)
 
-      -- se carico motosega, ruoto in zona sicura prima di approcciare la lavorazione
-      if ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
-         local sEEPreMove = ' EE' .. EgtIf( bZmax, '3', '4')
+      -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
+      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.FLAG2 == 1 then
          local sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
-                                       EmtGetAxis( 'R2') .. EmtGetAxis( 'R1') .. sEE .. sEL .. sER .. sET .. sES
+                                       ' B' .. EmtLenToString( EMT.R2pp, 3) .. ' C' .. EmtLenToString( EMT.R1pp, 3) .. 
+                                       ' EE' .. EgtIf( bZmax, '3', '4') .. EMT.PREVsEL .. EMT.PREVsER .. EMT.PREVsET .. EMT.PREVsES
+         EmtOutput( sOutPreMove)
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
+         EmtOutput( sOutPreMove)
+         EmtOutput( 'G101 ET1001')
+         EmtOutput( 'G101 ET2001')
+      end
+
+      if not EMT.LOAD then
+         local sOut = string.gsub( string.gsub( EMT.MCHNAME..'/'..EMT.TOOL, '%(', '-'), '%)', '-')
+         EmtOutput( '( *** ' .. sOut .. ' *** )')
+      end
+
+      -- se carico motosega, ruoto in zona sicura prima di approcciare la lavorazione
+      if not EMT.LOAD and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and 
+         ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
+         local sEEPreMove = ' EE' .. EgtIf( bZmax, '3', '4')
+         local sOutPreMove
+         if EMT.HEAD == 'H3' and bGoToHome then
+            sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1pp, 3) .. sEE .. sEL .. sER .. sET .. sES
+            EmtOutput( sOutPreMove)
+            sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( 0, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
+            EmtOutput( sOutPreMove)
+         end
+         sOutPreMove = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. ' Z' .. EmtLenToString( MyZHome, 3) ..
+                                       ' B' .. EgtNumToString( EMT.R2, 3) .. ' C' .. EgtNumToString( EMT.R1, 3) .. sEE .. sEL .. sER .. sET .. sES
          EmtOutput( sOutPreMove)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
@@ -923,13 +948,13 @@ function OnRapid()
          local sER = ' ER' .. EmtLenToString( EgtIf( EMT.HEAD ~= 'H3', EMT.TDIAM / 2, EMT.TLEN), 3)
          local sET = GetET( EMT.HEAD, EMT.TCPOS, EMT.R3)
          local sES = ' ES'..EgtNumToString( EMT.S, 0)
-         local sOut = 'G101' .. EmtGetAxis( 'L2') .. EmtGetAxis( 'L3') ..' B=' .. EgtNumToString( dBAxis, 3) ..
-                      ' C=' .. EgtNumToString( dCAxis, 3) .. sEE .. sEL .. sER .. sET .. sES
+         local sOut = 'G101' .. EmtGetAxis( 'L2') .. EmtGetAxis( 'L3') ..' B' .. EgtNumToString( dBAxis, 3) ..
+                      ' C' .. EgtNumToString( dCAxis, 3) .. sEE .. sEL .. sER .. sET .. sES
          EmtOutput( sOut)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
-         sOut = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. EmtGetAxis( 'L3') ..' B=' .. EgtNumToString( dBAxis, 3) ..
-                ' C=' .. EgtNumToString( dCAxis, 3) .. sEE .. sEL .. sER .. sET .. sES
+         sOut = 'G101' .. ' X' .. EmtLenToString( -SafeXRotAxes, 3) .. EmtGetAxis( 'L3') ..' B' .. EgtNumToString( dBAxis, 3) ..
+                ' C' .. EgtNumToString( dCAxis, 3) .. sEE .. sEL .. sER .. sET .. sES
          EmtOutput( sOut)
          EmtOutput( 'G101 ET1001')
          EmtOutput( 'G101 ET2001')
@@ -1091,28 +1116,6 @@ function FindNextTool()
    return sTool, sHead, sTcPos
 end
 
----------------------------------------------------------------------
-function CalcDinamicaPinze( dH, dS, dL)
-   local MinTempoAcc = 0.3                         -- [s]
-   local MaxTempoAcc = 4.0                         -- [s]
-   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
-   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
-   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
-   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
-   local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito) / 1000)
-   if ( TempoAcc < MinTempoAcc) then TempoAcc = MinTempoAcc end
-   if ( TempoAcc > MaxTempoAcc) then TempoAcc = MaxTempoAcc end
-   local AccMaxPinze = FMaxPinze / ( 60 * MinTempoAcc)
-   local AccPinze = FMaxPinze / ( 60 * TempoAcc)
-   local RidFeed = 100 / Massa * 100
-   if RidFeed > 100 then
-      RidFeed = 100
-   elseif RidFeed < 10 then
-      RidFeed = 10
-   end
-   return AccPinze, AccMaxPinze, RidFeed, TempoAcc
-end
-
 ---------------------------------------------------------------------
 function CalcCharStatus( sCmd, bSkipPress)
    -- aperto
@@ -1640,7 +1643,7 @@ function MyAdjustLinearAxes()
       if EMT.HEAD == 'H1' or EMT.HEAD == 'H2' then
          local Len = EMT.TLEN + EgtIf( EMT.HEAD == 'H1', MillOffs, abs( SawOffs))
          local LenRef = MillOffs
-         vtE = Vector3d( EMT.EXTR) * Len - Z_AX() * LenRef
+         vtE = Vector3d( EMT.TDIR) * Len - Z_AX() * LenRef
       elseif EMT.HEAD == 'H3' then
          local LenAux = ( EMT.TDIST or ChSawLen) + MillOffs
          local LenRef = MillOffs

Common_FAST.TPA.mlpe

@@ -6,7 +6,7 @@ local INFO_STD_PP = require( 'Version')
 local BD = require( 'BeamData')
 
 -- Variabili di modulo
-local CSP_INFO =     INFO_STD_PP.NAME..'  ver.'..INFO_STD_PP.VERSION..' by EgalWare s.r.l.'
+local CSP_INFO =     INFO_STD_PP.NAME..'_'..NumericalControl..'  ver.'..INFO_STD_PP.VERSION..' by EgalWare s.r.l.'
 local MACHINE_INFO = MACH_NAME..'  ver.'..PP_VER
 local TEST_USE = false
 
@@ -21,14 +21,19 @@ function OnStart()
    EMT.USETO1 = false     -- abilitazione uso origine tavola
    EMT.MODAL = true       -- abilitazione emissione modale
    EMT.INCHES = false     -- unità di misura mm/inches
-   EMT.DECNUM = 5         -- numero di decimali dopo la virgola
+   EMT.DECNUM = 4         -- numero di decimali dopo la virgola
+   EMT.DECVERS = 6        -- numero di decimali dopo la virgola per versori
+   EMT.DECRAD = 4         -- numero di decimali dopo la virgola per raggio
+   EMT.DECMACRO = 3       -- numero di decimali dopo la virgola per macro
    EMT.NUM = false        -- abilitazione numerazione linee
-   --EMT.Nt = 'N'           -- token per la numerazione di linea
-   --EMT.LINENBR = 0        -- numero di linea
-   --EMT.LINEINC = 1        -- incremento numerazione linee
-   --EMT.Ft = 'F'           -- token per feed
-   --EMT.St = 'S'           -- token per speed
-   EMT.FMAXPINZE = 154000 -- feed massima pinze
+   --EMT.Nt = 'N'         -- token per la numerazione di linea
+   --EMT.LINENBR = 0      -- numero di linea
+   --EMT.LINEINC = 1      -- incremento numerazione linee
+   --EMT.Ft = 'F'         -- token per feed
+   --EMT.St = 'S'         -- token per speed
+   EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+   EMT.MAXACC = MaxAcc or 4000    -- accelerazione massima pinze. In realtà è il tempo in millisecondi, quindi MAXACC corrisponde al tempo massimo per raggiungere la velocità desiderata
+   EMT.MINACC = MinAcc or 300     -- accelerazione minima pinze. In realtà è il tempo in millisecondi, quindi MINACC corrisponde al tempo massimo per raggiungere la velocità desiderata
 end
 
 ---------------------------------------------------------------------
@@ -51,6 +56,7 @@ function OnProgramStart()
    end
    ParkLine( sPrefixCommentLine..'('.. CSP_INFO..')')
    ParkLine( sPrefixCommentLine..'('.. MACHINE_INFO..')')
+   ParkLine( '(HEADER)')
 
    -- Se modalità test, aggiungo linee per muovere tappeto e alzare la testa (in automatico viene fatto dal main residente)
    if TEST_USE then
@@ -108,6 +114,7 @@ function OnProgramEnd()
    EMT.FALL = nil
    EMT.RELOAD = nil
    EMT.RELOAD2 = nil
+   EmtOutput( '(FOOTER)')
    -- Termino il programma
    EmtOutput( 'M02')
 end
@@ -116,8 +123,8 @@ end
 function OnToolData()
    -- emissione dati utensili
    if EMT.HEAD == 'H1' then
-      local sOut = 'M992 P1=' .. EMT.TCPOS:gsub( 'T', '') .. ' P2=' .. EmtLenToString( EMT.TLEN, 3) .. ' P3=' .. EmtLenToString( EMT.TDIAM, 3) ..
-                   ' P4=' .. EmtLenToString( EMT.SMAX, 3) .. ' P5=' .. EmtLenToString( EMT.TTOTLEN, 3)
+      local sOut = 'M992 P1=' .. EMT.TCPOS:gsub( 'T', '') .. ' P2=' .. EmtLenToString( EMT.TLEN, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( EMT.TDIAM, EMT.DECMACRO) ..
+                   ' P4=' .. EmtLenToString( EMT.SMAX, EMT.DECMACRO) .. ' P5=' .. EmtLenToString( EMT.TTOTLEN, EMT.DECMACRO)
       ParkLine( sOut)
       -- cerco posizione di attrezzaggio del primo utensile di lavorazione
       if EMT.TOOL == EMT.TOOL_1  and  EMT.TLEN_1 < LONG_TOOL_MINLEN then
@@ -125,14 +132,14 @@ function OnToolData()
       end
    -- emissione dati lama
    elseif EMT.HEAD == 'H2' then
-      local sOut = 'M992 P1=' .. EMT.TCPOS:gsub( 'T', '') .. ' P2=' .. EmtLenToString( EMT.TLEN, 3) .. ' P3=' .. EmtLenToString( EMT.TDIAM, 3) ..
-                   ' P4=' .. EmtLenToString( EMT.SMAX, 3) .. ' P5=' .. EmtLenToString( EMT.TTOTLEN, 3)
+      local sOut = 'M992 P1=' .. EMT.TCPOS:gsub( 'T', '') .. ' P2=' .. EmtLenToString( EMT.TLEN, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( EMT.TDIAM, EMT.DECMACRO) ..
+                   ' P4=' .. EmtLenToString( EMT.SMAX, EMT.DECMACRO) .. ' P5=' .. EmtLenToString( EMT.TTOTLEN, EMT.DECMACRO)
       ParkLine( sOut)
    -- emissione dati sega a catena
    elseif EMT.HEAD == 'H3' then
       if EMT.TDIST and abs( EMT.TDIST) < 0.1 then EMT.TDIST = nil end
-      local sData = ' P2=' .. EmtLenToString( ( EMT.TDIST or ChSawLen), 3) .. ' P3=' .. EmtLenToString( EMT.TLEN, 3) ..
-                    ' P4=' .. EmtLenToString( EMT.SMAX, 3) .. ' P5=' .. EmtLenToString( ( EMT.TDIST or ChSawLen), 3)
+      local sData = ' P2=' .. EmtLenToString( ( EMT.TDIST or ChSawLen), EMT.DECMACRO) .. ' P3=' .. EmtLenToString( EMT.TLEN, EMT.DECMACRO) ..
+                    ' P4=' .. EmtLenToString( EMT.SMAX, EMT.DECMACRO) .. ' P5=' .. EmtLenToString( ( EMT.TDIST or ChSawLen), EMT.DECMACRO)
       if EMT.TCPOS == 'T101' then
          ParkLine( 'M992 P1=101' .. sData)
          ParkLine( 'M992 P1=102' .. sData)
@@ -148,13 +155,13 @@ function OnToolData()
    elseif EMT.HEAD == 'H5' or EMT.HEAD == 'H6' then
       local nPos = EgtIf( EMT.HEAD == 'H5', 91, 93)
       if EMT.EXIT == 2 then nPos = nPos + 1 end
-      local sOut = 'M992 P1=' .. EgtNumToString( nPos, 0) .. ' P2=' .. EmtLenToString( EMT.TLEN, 3) .. ' P3=' .. EmtLenToString( EMT.TDIAM, 3) ..
-                   ' P4=' .. EmtLenToString( EMT.SMAX, 3) .. ' P5=' .. EmtLenToString( EMT.TTOTLEN, 3)
+      local sOut = 'M992 P1=' .. EgtNumToString( nPos, 0) .. ' P2=' .. EmtLenToString( EMT.TLEN, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( EMT.TDIAM, EMT.DECMACRO) ..
+                   ' P4=' .. EmtLenToString( EMT.SMAX, EMT.DECMACRO) .. ' P5=' .. EmtLenToString( EMT.TTOTLEN, EMT.DECMACRO)
       ParkLine( sOut)
    -- emissione dati sega a catena
    elseif EMT.HEAD == 'H7' then
-      local sOut = 'M992 P1=' .. EMT.TCPOS:gsub( 'T', '') .. ' P2=' .. EmtLenToString( EMT.TLEN, 3) .. ' P3=' .. EmtLenToString( EMT.TDIAM, 3) ..
-                   ' P4=' .. EmtLenToString( EMT.SMAX, 3) .. ' P5=' .. EmtLenToString( EMT.TTOTLEN, 3)
+      local sOut = 'M992 P1=' .. EMT.TCPOS:gsub( 'T', '') .. ' P2=' .. EmtLenToString( EMT.TLEN, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( EMT.TDIAM, EMT.DECMACRO) ..
+                   ' P4=' .. EmtLenToString( EMT.SMAX, EMT.DECMACRO) .. ' P5=' .. EmtLenToString( EMT.TTOTLEN, EMT.DECMACRO)
       ParkLine( sOut)
 -- altro non previsto
    else
@@ -218,14 +225,14 @@ function OnDispositionEnd()
       local HOverM = EMT.HOVM
 
       -- calcolo dati pinze
-      local TempAccPinze, TempMinAccPinze, RidFeed = CalcDinamicaPinze( HTrave, STrave, LBarra)
-      local TempAccPinz1, TempMinAccPinz1, RidFeed1 = CalcDinamicaPinze( HTrave, STrave, LBarra - LTrave)
-      local TempAccPinz2, TempMinAccPinz2, RidFeed2 = CalcDinamicaPinze( HTrave, STrave, LTrave)
+      local TempAccPinze, TempMinAccPinze, RidFeed = CalcDinamicaPinze_TPA( HTrave, STrave, LBarra)
+      local TempAccPinz1, TempMinAccPinz1, RidFeed1 = CalcDinamicaPinze_TPA( HTrave, STrave, LBarra - LTrave)
+      local TempAccPinz2, TempMinAccPinz2, RidFeed2 = CalcDinamicaPinze_TPA( HTrave, STrave, LTrave)
 
       if IdTrave >= 0 then
          local sPrt = '( *** Part '.. EgtNumToString( IdTrave, 0) ..' ***)'
-         local sOut = '( SN=' .. IdTrave .. ' LBarra=' .. EmtLenToString( LBarra, 3) .. ' L='..EmtLenToString( LTrave, 3) ..
-                      ' H=' .. EmtLenToString( HTrave, 3) .. ' S=' .. EmtLenToString( STrave, 3) .. ' )'
+         local sOut = '( SN=' .. IdTrave .. ' LBarra=' .. EmtLenToString( LBarra, EMT.DECMACRO) .. ' L='..EmtLenToString( LTrave, EMT.DECMACRO) ..
+                      ' H=' .. EmtLenToString( HTrave, EMT.DECMACRO) .. ' S=' .. EmtLenToString( STrave, EMT.DECMACRO) .. ' )'
          EMT.PRODID = EgtGetInfo( BtlInfoId, 'PRODID', 'i') or 0
          EMT.PATTID = EgtGetInfo( BtlInfoId, 'PATTID', 'i') or 0
          EMT.CUTID = EgtGetInfo( EMT.IDT, 'CUTID', 'i') or 0
@@ -268,9 +275,9 @@ function OnDispositionEnd()
                 ' P4=' .. EmtLenToString( HOverM, 2) .. ' P5=' .. tostring( nLoad90) .. ' P6=' .. EmtLenToString( EgtIf( IdTrave >= 0, LTrave, LBarra), 2) ..
                 ' P7=' .. EgtNumToString( TempAccPinze, 2) .. ' P8=' .. EgtNumToString( TempAccPinz2, 2) .. ' P9=' .. EgtNumToString( TempAccPinz1, 2)
          EmtOutput( sOut)
-         EmtOutput( 'M112'..' P1='..EmtLenToString( LoadT, 3).. ' P5=1 P6='..EmtLenToString( EMT.YPOS, 3)..' P7='..EmtLenToString( ParkV, 3) ..' P9='..GetFmaxClamp())
+         EmtOutput( 'M112'..' P1='..EmtLenToString( EMT.TPOS, 3).. ' P5=1 P6='..EmtLenToString( EMT.YPOS, 3)..' P7='..EmtLenToString( ParkV, 3) ..' P9='..GetFmaxClamp())
          -- aggiorno dati aggancio carrelli alla trave
-         EMT.YDELTA = EMT.YPOS - LoadT
+         EMT.YDELTA = EMT.YPOS - EMT.TPOS
          EMT.VDELTA = nil
       end
       -- eventuale preparazione per rotazione immediata
@@ -651,14 +658,26 @@ function OnRapid()
             bHeadFirst = false
          end
       end
+
+      local bGoToHome = false
+      -- se gli assi rotanti cambiano parecchio, con motosega si va in parcheggio 
+      if EMT.PREVHEAD == 'H3' and EMT.HEAD == 'H3' and EMT.TCPOS == EMT.PREVTCPOS and ( abs( EMT.R2pp - EMT.R2) > 25 or abs( EMT.R1pp - EMT.R1) > 25)  then
+         bGoToHome = true
+      end
+   
       -- primo posizionamento
       local MyZHome = EgtGetAxisHomePos( 'Z')
       local bZmax = ( #EMT.AUXSTR > 0  or  EMT.TOOL ~= EMT.PREVTOOL  or EMT.L3 > -1)
       -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-      if EMT.PREVHEAD == 'H3' and EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
-         local sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, 3) .. ' P3=' .. EmtLenToString( MyZHome, 3) ..
-                                 ' P4=' .. EgtNumToString( EMT.R2pp, 3) .. ' P5=' .. EgtNumToString( EMT.R1pp, 3) .. 
-                                 ' P6=' .. EgtNumToString( EMT.PREVTCPOS, 3) .. ' P7=' .. EgtNumToString( EMT.PREVS, 0) ..
+      if not EMT.LOAD and EMT.PREVHEAD == 'H3' and EMT.FLAG2 == 1 then
+         local sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+                                 ' P4=' .. EgtNumToString( EMT.R2pp, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1pp, EMT.DECMACRO) .. 
+                                 ' P6=' .. EgtNumToString( EMT.PREVTCPOS, EMT.DECMACRO) .. ' P7=' .. EgtNumToString( EMT.PREVS, 0) ..
+                                 ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
+         EmtOutput( sOutPreMove)
+         sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+                                 ' P4=' .. EgtNumToString( 0, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1pp, EMT.DECMACRO) .. 
+                                 ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
                                  ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
          EmtOutput( sOutPreMove)
          EmtOutput( 'M101 P1=2')
@@ -671,9 +690,23 @@ function OnRapid()
       end
 
       -- se carico motosega, ruoto in zona sicura prima di approcciare la lavorazione
-      if ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
-         local sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, 3) .. ' P3=' .. EmtLenToString( MyZHome, 3) ..
-                                 ' P4=' .. EgtNumToString( EMT.R2, 3) .. ' P5=' .. EgtNumToString( EMT.R1, 3) .. 
+      if not EMT.LOAD and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TTOTLEN > 200)) and 
+         ( EMT.ST > BeamHeightForFixRot or ( EMT.HEAD == 'H1' and EMT.TTOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
+         local sOutPreMove
+         if EMT.HEAD == 'H3' and bGoToHome then
+            sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+                                 ' P4=' .. EgtNumToString( 0, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1pp, EMT.DECMACRO) .. 
+                                 ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
+                                 ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
+            EmtOutput( sOutPreMove)
+            sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+                                 ' P4=' .. EgtNumToString( 0, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1, EMT.DECMACRO) .. 
+                                 ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
+                                 ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
+            EmtOutput( sOutPreMove)
+         end
+         sOutPreMove = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZHome, EMT.DECMACRO) ..
+                                 ' P4=' .. EgtNumToString( EMT.R2, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1, EMT.DECMACRO) .. 
                                  ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
                                  ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
          EmtOutput( sOutPreMove)
@@ -687,8 +720,8 @@ function OnRapid()
       if EMT.ST > BeamHeightForFixRot and EMT.FLAG2 == 1 then
          MyZPos = MyZHome
       end
-      local sOut = 'M101 P1=1' .. ' P2=' .. EmtLenToString( EMT.L2, 3) .. ' P3=' .. EmtLenToString( MyZPos, 3) ..
-                       ' P4=' .. EgtNumToString( EMT.R2, 3) .. ' P5=' .. EgtNumToString( EMT.R1, 3) .. 
+      local sOut = 'M101 P1=1' .. ' P2=' .. EmtLenToString( EMT.L2, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( MyZPos, EMT.DECMACRO) ..
+                       ' P4=' .. EgtNumToString( EMT.R2, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1, EMT.DECMACRO) .. 
                        ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
                        ' P8=0' .. ' P9=0' .. ' P10=' .. EgtIf( bZmax, '3', '4')
       if EMT.LOAD then
@@ -738,7 +771,7 @@ function OnRapid()
             sV = EmtLenToString( ParkV)
             sB = '2'
          end
-         sOut = 'M112 P1='..EmtLenToString( EMT.L1, 3)..' P3='..sA..' P4='..sB..' P5=0 P6='..sY..' P7='..sV..' P9='..GetFmaxClamp()
+         sOut = 'M112 P1='..EmtLenToString( EMT.L1, EMT.DECMACRO)..' P3='..sA..' P4='..sB..' P5=0 P6='..sY..' P7='..sV..' P9='..GetFmaxClamp()
          ParkLine( sOut)
          EMT.LOAD = false
          -- emissione prime linee speciali e linee parcheggiate
@@ -789,7 +822,7 @@ function OnRapid()
             sOut = 'M101 P1=3'
             EmtOutput( sOut)
          end
-         sOut = 'M112 P1=' .. EmtLenToString( EMT.L1, 3) ..' P3='..sA..' P4='..sB..' P6='..sY..' P7='..sV..' P9=' .. GetFmaxClamp()
+         sOut = 'M112 P1=' .. EmtLenToString( EMT.L1, EMT.DECMACRO) ..' P3='..sA..' P4='..sB..' P6='..sY..' P7='..sV..' P9=' .. GetFmaxClamp()
          EmtOutput( sOut)
          if not bHeadFirst then
             sOut = 'M101 P1=2'
@@ -861,15 +894,15 @@ function OnRapid()
       if EMT.ST > BeamHeightForFixRot  and  EMT.HEAD == 'H1' and  EMT.TOOL ~= EMT.NEXTTOOL  and  EMT.NEXTHEAD ~= 'H2' then
          local dBAxis = 90
          local dCAxis = EgtIf( BD.RIGHT_LOAD, 90, -90)
-         local sOut = 'M101 P1=1' .. ' P2=' .. EmtLenToString( EMT.L2, 3) .. ' P3=' .. EmtLenToString( EMT.L3, 3) ..
-                      ' P4=' .. EgtNumToString( dBAxis, 3) .. ' P5=' .. EgtNumToString( dCAxis, 3) .. 
+         local sOut = 'M101 P1=1' .. ' P2=' .. EmtLenToString( EMT.L2, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( EMT.L3, EMT.DECMACRO) ..
+                      ' P4=' .. EgtNumToString( dBAxis, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( dCAxis, EMT.DECMACRO) .. 
                       ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
                       ' P8=0' .. ' P9=0' .. ' P10=3'
          EmtOutput( sOut)
          EmtOutput( 'M101 P1=2')
          EmtOutput( 'M101 P1=3')
-         sOut = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, 3) .. ' P3=' .. EmtLenToString( EMT.L3, 3) ..
-                      ' P4=' .. EgtNumToString( dBAxis, 3) .. ' P5=' .. EgtNumToString( dCAxis, 3) .. 
+         sOut = 'M101 P1=1' .. ' P2=' .. EmtLenToString( -SafeXRotAxes, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( EMT.L3, EMT.DECMACRO) ..
+                      ' P4=' .. EgtNumToString( dBAxis, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( dCAxis, EMT.DECMACRO) .. 
                       ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
                       ' P8=0' .. ' P9=0' .. ' P10=3'
          EmtOutput( sOut)
@@ -886,8 +919,8 @@ function OnRapid()
       MyAdjustLinearAxes()
       EmtAdjustRotaryAxes()
       EmtResetPrev()
-      local sOut = 'M101 P1=1' .. ' P2=' .. EmtLenToString( EMT.L2, 3) .. ' P3=' .. EmtLenToString( EMT.L3, 3) ..
-                   ' P4=' .. EgtNumToString( EMT.R2, 3) .. ' P5=' .. EgtNumToString( EMT.R1, 3) .. 
+      local sOut = 'M101 P1=1' .. ' P2=' .. EmtLenToString( EMT.L2, EMT.DECMACRO) .. ' P3=' .. EmtLenToString( EMT.L3, EMT.DECMACRO) ..
+                   ' P4=' .. EgtNumToString( EMT.R2, EMT.DECMACRO) .. ' P5=' .. EgtNumToString( EMT.R1, EMT.DECMACRO) .. 
                    ' P6=' .. AdjustTcPos( false) .. ' P7=' .. EgtNumToString( EMT.S, 0) ..
                    ' P8=0' .. ' P9=0' .. ' P10=3'
       EmtOutput( sOut)
@@ -1007,7 +1040,7 @@ function OnArc()
    --local sCen = ' ' .. EMT.C1t .. EmtLenToString(EMT.C1,3) ..
    --             ' ' .. EMT.C2t .. EmtLenToString(EMT.C2,3)
    -- raggio
-   local sRad = ' ' .. EMT.RRt .. EmtLenToString( EMT.RR, EMT.DECNUM)
+   local sRad = ' ' .. EMT.RRt .. EmtLenToString( EMT.RR, EMT.DECRAD)
    -- aggiungo feed
    local sFeed = EmtGetFeed()
    -- tipo arco
@@ -1048,28 +1081,6 @@ function FindNextTool()
    return sTool, sHead, sTcPos
 end
 
----------------------------------------------------------------------
-function CalcDinamicaPinze( dH, dS, dL)
-   local MinTempoAcc = 0.3                         -- [s]
-   local MaxTempoAcc = 4.0                         -- [s]
-   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
-   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
-   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
-   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
-   local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito) / 1000)
-   if ( TempoAcc < MinTempoAcc) then TempoAcc = MinTempoAcc end
-   if ( TempoAcc > MaxTempoAcc) then TempoAcc = MaxTempoAcc end
-   local AccMaxPinze = FMaxPinze / ( 60 * MinTempoAcc)
-   local AccPinze = FMaxPinze / ( 60 * TempoAcc)
-   local RidFeed = 100 / Massa * 100
-   if RidFeed > 100 then
-      RidFeed = 100
-   elseif RidFeed < 10 then
-      RidFeed = 10
-   end
-   return TempoAcc * 1000, MinTempoAcc * 1000, RidFeed
-end
-
 ---------------------------------------------------------------------
 function CalcCharStatus( sCmd, bSkipPress)
    -- aperto
@@ -1639,7 +1650,7 @@ function MyAdjustLinearAxes()
       if EMT.HEAD == 'H1' or EMT.HEAD == 'H2' then
          local Len = EMT.TLEN + EgtIf( EMT.HEAD == 'H1', MillOffs, abs( SawOffs))
          local LenRef = MillOffs
-         vtE = Vector3d( EMT.EXTR) * Len - Z_AX() * LenRef
+         vtE = Vector3d( EMT.TDIR) * Len - Z_AX() * LenRef
       elseif EMT.HEAD == 'H3' then
          local LenAux = ( EMT.TDIST or ChSawLen) + MillOffs
          local LenRef = MillOffs
@@ -1650,13 +1661,13 @@ function MyAdjustLinearAxes()
          local LenAux = MillOffs + AngTr1Offs
          local LenRef = MillOffs
          local vtAux = EgtGetCalcAuxDirFromAngles( EMT.R1, EMT.R2)
-         vtE = Vector3d( EMT.EXTR) * Len + vtAux * LenAux - Z_AX() * LenRef
+         vtE = Vector3d( EMT.TDIR) * Len + vtAux * LenAux - Z_AX() * LenRef
       elseif  EMT.HEAD == 'H7' then
          local Len = EMT.TLEN + AngTrBHLen
          local LenAux = MillOffs + AngTrBHOffs
          local LenRef = MillOffs
          local vtAux = EgtGetCalcAuxDirFromAngles( EMT.R1, EMT.R2)
-         vtE = Vector3d( EMT.EXTR) * Len + vtAux * LenAux - Z_AX() * LenRef
+         vtE = Vector3d( EMT.TDIR) * Len + vtAux * LenAux - Z_AX() * LenRef
       else
          EmtSetLastError( 1211, 'Head not allowed ' .. EMT.HEAD)
       end
@@ -1767,9 +1778,9 @@ function CalcInterpPlane()
    local vtY = EMT.IPLGLFR:getVersY()
    local vtZ = EMT.IPLGLFR:getVersZ()
    EMT.IPLGLSTR = ' X0 Y' .. EmtLenToString( xS, EMT.DECNUM) .. ' Z0' ..
-                  ' A' .. EgtNumToString( - vtX:getY(), 6) .. ' B' .. EgtNumToString( vtX:getX(), 6) .. ' C' .. EgtNumToString( vtX:getZ(), 6) ..
-                  ' I' .. EgtNumToString( - vtY:getY(), 6) .. ' J' .. EgtNumToString( vtY:getX(), 6) .. ' K' .. EgtNumToString( vtY:getZ(), 6) ..
-                  ' P' .. EgtNumToString( - vtZ:getY(), 6) .. ' Q' .. EgtNumToString( vtZ:getX(), 6) .. ' R' .. EgtNumToString( vtZ:getZ(), 6)
+                  ' A' .. EgtNumToString( - vtX:getY(), EMT.DECVERS) .. ' B' .. EgtNumToString( vtX:getX(), EMT.DECVERS) .. ' C' .. EgtNumToString( vtX:getZ(), EMT.DECVERS) ..
+                  ' I' .. EgtNumToString( - vtY:getY(), EMT.DECVERS) .. ' J' .. EgtNumToString( vtY:getX(), EMT.DECVERS) .. ' K' .. EgtNumToString( vtY:getZ(), EMT.DECVERS) ..
+                  ' P' .. EgtNumToString( - vtZ:getY(), EMT.DECVERS) .. ' Q' .. EgtNumToString( vtZ:getX(), EMT.DECVERS) .. ' R' .. EgtNumToString( vtZ:getZ(), EMT.DECVERS)
    EMT.IPLGL = true
 end
 

Common_FAST.mlpe

@@ -7,9 +7,6 @@ EgtEnableDebug( false)
 -- carico librerie
 local BD = require( 'BeamData')
 
-LONG_TOOL_MINLEN = 221
-BIG_TOOL_DIAM = 300
-
 ---------------------------------------------------------------------
 -- *** GENERATION ***
 ---------------------------------------------------------------------
@@ -82,6 +79,14 @@ function OnSimulStart()
          for j = 1, #( vTools or {}) do
             if vTools[j] ~= '' then
                EgtLoadTool( vTcPos[i], j, vTools[j])
+               -- Aggiunto controllo lunghezza lama minima * 0.9 per ricavare la tolleranza del VMILL
+               if EgtTdbSetCurrTool(vTools[j]) then -- set utensile corrente
+                  if EgtTdbGetCurrToolParam( MCH_TP.TYPE) == MCH_TY.SAW_STD or EgtTdbGetCurrToolParam( MCH_TP.TYPE) == MCH_TY.SAW_FLAT then -- controllo tipo utensile sega
+                     local dCurrSawLen = EgtTdbGetCurrToolParam( MCH_TP.LEN) * 0.9
+                     -- se non definito o minore del valore precedente aggiorna la tolleranza
+                     EMT.VMILLTOL = EgtIf( not EMT.VMILLTOL or dCurrSawLen < EMT.VMILLTOL, dCurrSawLen, EMT.VMILLTOL) 
+                  end
+               end
             end
          end
          ShowToolInTcPos( vTcPos[i], true)
@@ -118,7 +123,8 @@ function OnSimulStart()
                      { Grp = 'V', Sub = 'COLLISION', Name = 'VOL2'},
                      { Grp = 'PV', Sub = 'COLLISION', Name = 'VOL'},
                      { Grp = 'Base', Sub = 'COLLISION', Name = 'SIDE1'},
-                     { Grp = 'Base', Sub = 'COLLISION', Name = 'SIDE2'}}
+                     { Grp = 'Base', Sub = 'COLLISION', Name = 'SIDE2'},
+                     { Grp = 'C', Sub = 'COLLISION2', Name = 'C_TOP'}}
    EgtOutLog( 'MCODET Objects :', 4)
    local nMcdNullCnt = 0
    for i = 1, #McdData do
@@ -142,6 +148,30 @@ function OnSimulStart()
    end
    -- Preparo lista collisioni vuota
    EMT.COLLIDE = {}
+
+      -- si crea gruppo temporaneo appoggio controllo clamping
+   CLAMP_CHECK_GROUP = EgtGetFirstNameInGroup( GDB_ID.ROOT, 'CLAMP_CHECK')
+   CLAMP_CHECK_INTERS = EgtGetFirstNameInGroup( GDB_ID.ROOT, 'CLAMP_INTERS')
+
+   if CLAMP_CHECK_GROUP then
+      EgtEmptyGroup( CLAMP_CHECK_GROUP)
+   else
+      local frClampCheckGroup = Frame3d( ORIG(), GDB_FR.FRONT)
+      CLAMP_CHECK_GROUP = EgtGroup( GDB_ID.ROOT, frClampCheckGroup)
+      EgtSetName( CLAMP_CHECK_GROUP, 'CLAMP_CHECK')
+      EgtSetLevel( CLAMP_CHECK_GROUP, GDB_LV.TEMP)
+      EgtSetStatus( CLAMP_CHECK_GROUP, GDB_ST.OFF)
+   end
+   
+   if CLAMP_CHECK_INTERS then
+      EgtEmptyGroup( CLAMP_CHECK_INTERS)
+   else
+      CLAMP_CHECK_INTERS = EgtGroup( GDB_ID.ROOT)
+      EgtSetName( CLAMP_CHECK_INTERS, 'CLAMP_INTERS')
+      EgtSetLevel( CLAMP_CHECK_INTERS, GDB_LV.TEMP)
+      EgtSetStatus( CLAMP_CHECK_INTERS, GDB_ST.OFF)
+   end
+
 end
 
 ---------------------------------------------------------------------
@@ -168,13 +198,13 @@ function OnSimulDispositionStart()
       -- Determino dimensioni del grezzo
       local nSolId = EgtGetFirstNameInGroup( EgtGetFirstRawPart() or GDB_ID.NULL, 'RawSolid') or GDB_ID.NULL
       local b3Sol = EgtGetBBoxGlob( nSolId, GDB_BB.STANDARD)
-      EMT.LB = 0
-      EMT.SB = 0
-      EMT.HB = 0
+      EMT.LT = 0
+      EMT.ST = 0
+      EMT.HT = 0
       if b3Sol then
-         EMT.LB = b3Sol:getDimX()
-         EMT.SB = b3Sol:getDimY()
-         EMT.HB = b3Sol:getDimZ()
+         EMT.LT = b3Sol:getDimX()
+         EMT.ST = b3Sol:getDimY()
+         EMT.HT = b3Sol:getDimZ()
       end
       -- Carico primo utensile sulla testa 1
       local sTool, nTlen = FindFirstToolOnHead( 'H1')
@@ -215,7 +245,7 @@ function OnSimulDispositionStart()
             -- determino la risoluzione dello Zmap
             local dTol = 4.71
             if EmtGetVMillStep then
-               dTol = EmtGetVMillStep( b3Raw:getDimX(), b3Raw:getDimY(), b3Raw:getDimZ(), 4.71)
+               dTol = EmtGetVMillStep( b3Raw:getDimX(), b3Raw:getDimY(), b3Raw:getDimZ(), dTol)
             else
                local dArea = b3Raw:getDimX() * b3Raw:getDimY() + b3Raw:getDimX() * b3Raw:getDimZ() + b3Raw:getDimY() * b3Raw:getDimZ()
                if dArea < 0.075e6 then
@@ -232,6 +262,7 @@ function OnSimulDispositionStart()
                   dTol = 3.77
                end
             end
+            dTol = min( dTol, EMT.VMILLTOL or dTol) -- imposto dTol al valore minore tra quello per volume e quello per spessore lama
             -- creo lo Zmap
             local VMillId = EgtVolZmapBox( nPartRawId, b3Raw:getMin(), b3Raw:getDimX(), b3Raw:getDimY(), b3Raw:getDimZ(), dTol, true, GDB_RT.GLOB)
             if VMillId then
@@ -289,18 +320,24 @@ function OnSimulDispositionStart()
       local nOrd = GetPhaseOrd( EMT.PHASE)
       local nScrapOrd = GetPhaseOrd( EgtGetPhaseCount()) + 1
       local b3Raw = BBox3d()
+      local b3Bar = BBox3d()
+      local b3Part = BBox3d()
       local nPartRawId, nScrapRawId
       local nRawId = EgtGetFirstRawPart()
       while nRawId do
          local nNextRawId = EgtGetNextRawPart( nRawId)
          if EgtVerifyRawPartPhase( nRawId, EMT.PHASE) then
             EmtLinkRawPartToGroup( nRawId, 'Tab')
+            local b3Tmp = EgtGetRawPartBBox( nRawId)
+            b3Bar:Add( b3Tmp)
             local nRawOrd = EgtGetInfo( nRawId, 'ORD', 'i')
             if nRawOrd == nOrd then
-               b3Raw = EgtGetRawPartBBox( nRawId)
+               --b3Raw = EgtGetRawPartBBox( nRawId)
+               b3Raw:Add( b3Tmp)
+               b3Part:Add( b3Tmp)
                nPartRawId = nRawId
             elseif nRawOrd == nOrd + 1 and nRawOrd == nScrapOrd then
-               local b3Tmp = EgtGetRawPartBBox( nRawId) or BBox3d()
+               --local b3Tmp = EgtGetRawPartBBox( nRawId) or BBox3d()
                b3Raw:Add( b3Tmp)
                nScrapRawId = nRawId
             end
@@ -314,6 +351,9 @@ function OnSimulDispositionStart()
       else
          EMT.SCRAP = nil
       end
+      EMT.LB = b3Bar:getDimX()
+      EMT.LR = b3Raw:getDimX()
+      EMT.LT = b3Part:getDimX()
       -- recupero CutId del pezzo in lavorazione
       EMT.CUTID = EgtGetInfo( EgtGetFirstPartInRawPart( nPartRawId or GDB_ID.NULL) or GDB_ID.NULL, 'CUTID', 'i') or 0
       EMT.YSPEC = nil
@@ -385,6 +425,7 @@ function OnSimulDispositionStart()
          if EgtVerifyRawPartPhase( nRawId, EMT.PHASE) then
             if EgtGetInfo( nRawId, 'ORD', 'i') == nOrd then
                EmtLinkRawPartToGroup( nRawId, 'Tab')
+               b3Bar = EgtGetRawPartBBox( nRawId)
             else
                EgtMove( nRawId, vtMove, GDB_RT.GLOB)
                EgtSetStatus( nRawId, GDB_ST.OFF)
@@ -392,6 +433,8 @@ function OnSimulDispositionStart()
          end
          nRawId = nNextRawId
       end
+      EMT.LB = b3Bar:getDimX()
+
    -- altrimenti fase finale, aggancio primo grezzo alla tavola e gli altri in posizione carico al carro Y
    else
       -- verifico posizione di carico
@@ -409,12 +452,14 @@ function OnSimulDispositionStart()
          nRawId = EgtGetNextRawPart( nRawId)
       end
       -- eseguo
+      local b3Bar = BBox3d()
       nRawId = EgtGetFirstRawPart()
       while nRawId do
          local nNextRawId = EgtGetNextRawPart( nRawId)
          if EgtVerifyRawPartPhase( nRawId, EMT.PHASE) then
             if EgtGetInfo( nRawId, 'ORD', 'i') == nOrd then
                EmtLinkRawPartToGroup( nRawId, 'Tab')
+               b3Bar = EgtGetRawPartBBox( nRawId)
             else
                EgtMove( nRawId, vtMove, GDB_RT.GLOB)
                EmtLinkRawPartToGroup( nRawId, 'Y')
@@ -422,6 +467,7 @@ function OnSimulDispositionStart()
          end
          nRawId = nNextRawId
       end
+	  EMT.LB = b3Bar:getDimX()
    end
    -- Indicazione angolo rotazione pezzo
    EMT.ROT = EgtGetInfo( EMT.DISPID, 'ROT', 'i') or 0
@@ -453,6 +499,7 @@ function OnSimulDispositionEnd()
          EMT.POSTROT = true
       end
    end
+   EMT.SPLIT = false
    EMT.OPEISDISP = false
 end
 
@@ -466,8 +513,10 @@ function OnSimulToolSelect( dPosA)
    EMT.TOTDIAM = EgtTdbGetCurrToolParam( MCH_TP.TOTDIAM)
    -- se non è chiamato da altro script (non c'è parametro)
    if not dPosA then
-      -- se attivo Vmill
-      SetToolForVmill( EMT.TOOL, EMT.HEAD, EMT.EXIT, EMT.VMILL)
+      -- se utensile non flottante, abilito per Vmill
+      if not EMT.TFLOAT then
+         EmtSetToolForVmill( EMT.TOOL, EMT.HEAD, EMT.EXIT, EMT.VMILL)
+      end
       -- se attivo Collision Check
       EMT.SAFEDIST = COLL_SAFE_DIST
       if EMT.COLLOBJ then
@@ -520,14 +569,21 @@ function OnSimulToolSelect( dPosA)
       elseif EMT.HEAD == 'H7' then
          EgtSetAxisPos( 'C', EgtIf( BD.RIGHT_LOAD, 180, 0))
       end
+      -- se TC 1
+      if GetTCSet( EMT.TCPOS) == 1 then
+         EgtSetAxisPos( 'B', 90)
+      else
+         if EMT.HEAD ~= 'H3' then
+            EgtSetAxisPos( 'B', -90)
+         end
+      end
       -- se punta lunga
       if EMT.TOTLEN > LONG_TOOL_MINLEN then
          -- se su cambio utensile T111
          if EMT.TCPOS == 'T111' then
             EgtSetAxisPos( 'B', 0)
          end
-      end
-      -- breve pausa
+      end      -- breve pausa
       EgtPause( 100)
       EgtOutText( '')
       EMT.TOOL_1 = EMT.TOOL
@@ -549,24 +605,24 @@ function OnSimulToolDeselect()
       -- movimento scarico sega a catena
       if EMT.HEAD == 'H3' then
          -- se avevo motosega, torno in zona sicura senza ruotare assi rotanti
-         if  EMT.HB > BeamHeightForFixRot then
-            SimulMoveAxis( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID)
-         end
+         SimulMoveAxis( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID)
+         -- raddrizzo asse B prima di ruotare il C
+         SimulMoveAxis( 'B', 0, MCH_SIM_STEP.COLLROT)
          local dPosA = EgtGetAxisPos( 'A')
          if abs( dPosA) < 0.1 then
-            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 180, 0), MCH_SIM_STEP.COLLROT)
+            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, -180, 0), MCH_SIM_STEP.COLLROT)
          else
-            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.COLLROT)
+            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, 270), MCH_SIM_STEP.COLLROT)
          end
          SimulMoveAxis( 'X', 0, MCH_SIM_STEP.RAPID)
       -- movimento scarico rinvio
       elseif EMT.HEAD == 'H5' or EMT.HEAD == 'H6' then
-         SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', -90, MCH_SIM_STEP.COLLROT)
+         SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.COLLROT)
          SimulMoveAxis( 'X', 0, MCH_SIM_STEP.RAPID)
       -- movimento scarico aggregato BlockHaus
       elseif EMT.HEAD == 'H7' then
          SimulMoveAxis( 'X', 0, MCH_SIM_STEP.RAPID)
-         SimulMoveAxes( 'B', 90, MCH_SIM_STEP.COLLROT, 'C', -90, MCH_SIM_STEP.COLLROT)
+         SimulMoveAxes( 'B', 90, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.COLLROT)
       -- movimento scarico punta lunga su T111
       elseif EMT.TOTLEN > LONG_TOOL_MINLEN then
          -- se su cambio utensile T111
@@ -576,7 +632,11 @@ function OnSimulToolDeselect()
          -- altrimenti posizioni standard rastrelliera
          else
             SimulMoveAxis( 'X', 0, MCH_SIM_STEP.RAPID)
-            SimulMoveAxes( 'B', 90, MCH_SIM_STEP.COLLROT, 'C', -90, MCH_SIM_STEP.COLLROT)
+            if GetTCSet( EMT.TCPOS) == 1 then
+               SimulMoveAxes( 'B', 90, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.COLLROT)
+            else
+               SimulMoveAxes( 'B', -90, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.COLLROT)
+            end
          end
       -- movimento scarico utensile di grosso diametro (su T111)
       else
@@ -590,18 +650,34 @@ function OnSimulToolDeselect()
       -- nascondo utensile su testa e lo visualizzo su TcPos
       EgtSetMode( EgtGetHeadId( EMT.HEAD), GDB_MD.HIDDEN)
       ShowToolInTcPos( EMT.TCPOS_1, true)
+
       -- movimento per carico utensile
       if EMT.NEXTHEAD ~= 'H3' and EMT.NEXTHEAD ~= 'H5' and EMT.NEXTHEAD ~= 'H6' then
-         SimulMoveAxes( 'B', 90, MCH_SIM_STEP.RAPROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.RAPROT)
+         SimulMoveAxes( 'B', EgtIf( GetTCSet( EMT.TCPOS) == 1, 90, -90), MCH_SIM_STEP.RAPROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.RAPROT)
       else
-         SimulMoveAxes( 'B', 0, MCH_SIM_STEP.RAPROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.RAPROT)
+         if EMT.NEXTHEAD == 'H3' then
+            local dPosA = EgtGetAxisPos( 'A')
+            if abs( dPosA) < 0.1 then
+               SimulMoveAxes( 'B', 0, MCH_SIM_STEP.RAPROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, 270), MCH_SIM_STEP.RAPROT)
+            else
+               SimulMoveAxes( 'B', 0, MCH_SIM_STEP.COLLROT, 'C', EgtIf( BD.RIGHT_LOAD, -180, 0), MCH_SIM_STEP.COLLROT)
+            end
+         else
+            SimulMoveAxes( 'B', 0, MCH_SIM_STEP.RAPROT, 'C', EgtIf( BD.RIGHT_LOAD, 90, -90), MCH_SIM_STEP.RAPROT)
+         end
       end
       -- se segue lama, carico utensile di default
       if EMT.NEXTHEAD == 'H2' then
          local sDefTool = GetDefaultToolName()
-         EgtLoadTool( 'H1', 1, sDefTool)
          EMT.TOOL_1 = sDefTool
          EMT.TCPOS_1 = GetToolTcPos( EMT.TOOL_1)
+         -- se TC 1
+         if GetTCSet( EMT.TCPOS_1) == 1 then
+            EgtSetAxisPos( 'B', 90)
+         else
+            EgtSetAxisPos( 'B', -90)
+         end
+         EgtLoadTool( 'H1', 1, sDefTool)
          -- lo nascondo sul portautensili
          ShowToolInTcPos( EMT.TCPOS_1, false)
       end
@@ -678,6 +754,7 @@ function OnSimulMachiningEnd()
       EMT.UNLOADING = false
       EMT.FALL = false
    end
+   EMT.SPLIT = nil
    EMT.PREVHEAD = EMT.HEAD
    EMT.PREVTOOL = EMT.TOOL
    EMT.PREVEXIT = EMT.EXIT
@@ -765,33 +842,84 @@ function OnSimulMoveStart()
    VerifyVStroke( EMT.A2)
    -- se inizio lavorazione
    if EMT.MCHFIRST then
+
+      local bGoToHome = false
+      -- se gli assi rotanti cambiano parecchio, con motosega si va in parcheggio 
+      if EMT.PREVHEAD == 'H3' and EMT.HEAD == 'H3' and EMT.TOOL == EMT.PREVTOOL and abs( EMT.R3p - EMT.R3) < 100 * GEO.EPS_SMALL and ( abs( EMT.R2p - EMT.R2) > 25 or abs( EMT.R1p - EMT.R1) > 25)  then
+         bGoToHome = true
+      end
+
       EgtOutText( '')
       EMT.MCHFIRST = false
       local bZmax = ( EMT.TOOL ~= EMT.PREVTOOL  or EMT.L3 > -1)
-
       -- con pezzi alti aggiorno gli assi rotanti prima di muovermi sopra il pezzo
-      if not EMT.LOAD and EMT.MOVE == 0 and EMT.HB > BeamHeightForFixRot and EMT.FLAG2 == 1 then
-         -- se motosega mi muovo a X di sicurezza per ruotare
-         if ( EMT.HEAD == 'H3' or ( bZmax and EMT.TOTLEN > 200)) then
+      if not EMT.LOAD and EMT.MOVE == 0 and ( EMT.HEAD == 'H3' or ( bZmax and EMT.TOTLEN > 200)) and 
+         ( EMT.HT > BeamHeightForFixRot  or ( EMT.HEAD == 'H1' and EMT.TOTLEN > 350) or bGoToHome) and EMT.FLAG2 == 1 then
+         -- se motosega mi muovo a X di sicurezza per ruotare, prima si raddrizza B e poi C in posizione
+         if EMT.HEAD == 'H3' or bGoToHome then
+            SimulMoveAxis( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID)
+            SimulMoveAxis( 'B', 0, MCH_SIM_STEP.COLLROT)
+            SimulMoveAxis( 'C', EMT.R1, MCH_SIM_STEP.COLLROT)
+            SimulMoveAxis( 'B', EMT.R2, MCH_SIM_STEP.COLLROT)
+         elseif ( bZmax and EMT.TOTLEN > 200) then
             SimulMoveAxes( 'X', SafeXRotAxes, MCH_SIM_STEP.RAPID, 'C', EMT.R1, MCH_SIM_STEP.COLLROT, 'B', EMT.R2, MCH_SIM_STEP.COLLROT)
          end
       end
       EMT.POSTROT = nil
    end
+   -- se aggregato flottante su inizio attacco va compresso
+   if EMT.TFLOAT and not EMT.TFLOAT_CMP and EMT.MOVE == 1 and EgtGetName( EMT.MOVEID) == 'LI' then
+      -- recupero lunghezza 
+      local dOffsL = - EgtGetMachiningParam( MCH_MP.OFFSL)
+      -- imposto compressione della parte flottante
+      SetFloatPos( EMT.HEAD, dOffsL)
+      -- imposto dati utensile in posizione compressa
+      EmtSetToolForVmill( EMT.TOOL, EMT.HEAD, EMT.EXIT, EMT.VMILL, 2, -dOffsL)
+      -- dichiaro che è compresso (assegnando Id entità di movimento)
+      EMT.TFLOAT_CMP = EMT.MOVEID
+   end
 end
 
 ---------------------------------------------------------------------
 function OnSimulMoveEnd()
+   -- se termine di passata con lama
    if EMT.FLAG == 301 then 
       -- rimozione eventuali sfridi
       ExecRemoveScraps()
    end
+   -- se utensile flottante e movimento di compressione
+   if EMT.TFLOAT and EMT.MOVEID == EMT.TFLOAT_CMP then
+      -- verifico ci sia stata collisione tra ghiera flottante (portautensile e pezzo)
+      if not EMT.TFLOAT_TH_COMPR_COLL then
+         local sErr = 'CUTID='..tostring( EMT.CUTID)..'; TASKID='..tostring( EMT.TASKID)..'; Mach='..EMT.MCHNAME..'; Floating Ring not compressed on approach'
+         EmtSetLastError( 1222, sErr)
+         EgtOutLog( 'Error : ' .. sErr, 1)
+      else
+         EgtOutLog( 'Floating Ring compressed on approach (MOVEID='..EgtNumToString( EMT.MOVEID)..')', 1)
+      end
+      EMT.TFLOAT_TH_COMPR_COLL = nil
+   end
+   -- se aggregato flottante su fine uscita va rilasciato
+   if EMT.TFLOAT and EMT.TFLOAT_CMP and EMT.MOVE == 1 and EgtGetName( EMT.MOVEID) == 'LO' and EgtGetName( EgtGetNext( EMT.MOVEID) or GDB_ID.NULL) ~= 'LO' then
+      -- reset compressione della parte flottante
+      SetFloatPos( EMT.HEAD, 0)
+      -- dichiaro che è rilasciato
+      EMT.TFLOAT_CMP = nil
+   end
 end
 
 ---------------------------------------------------------------------
 function OnSimulCollision()
    -- se prima collisione della lavorazione, la segnalo
    if EMT.MCHNAME ~= EMT.LAST_MCHNAME_COLLIDE then
+      -- speciale per utensile flottante (suo holder contro il grezzo)
+      if EMT.TFLOAT and EMT.TFLOAT_CMP and EMT.SIMCOBIND == 1002 and EMT.SIMVMID == EMT.VMILL[1] then
+         if EMT.MOVEID == EMT.TFLOAT_CMP then
+            EMT.TFLOAT_TH_COMPR_COLL = true
+         end
+         return
+      end
+      -- standard
       local Class = ''
       if EMT.SIMCOBIND == 1001 then
          Class = 'T_H1'
@@ -815,6 +943,8 @@ function ExecAuxCmd( sCmd)
    if Cmd[1] == '0' then
       if Cmd[2] == 'Unloading' then
          EMT.UNLOADING = true
+      elseif Cmd[2] == 'Split' then
+         EMT.SPLIT = true
       elseif  Cmd[2] == 'Fall' then
          EMT.FALL = true
       end
@@ -856,19 +986,9 @@ function ExecAuxCmd( sCmd)
          end
       end
    elseif Cmd[1] == '11' then
-      local dPY = MaxOpen
-      if Cmd[2] ~= '0' then
-         dPY = EgtIf( EMT.ROT == -1, EMT.HB, EMT.SB)
-      end
-      SimulMoveAxis( 'PY', dPY, MCH_SIM_STEP.RAPID)
-      SetPYLight( Cmd[2] ~= '0')
+      ExecMovePY( Cmd[2] ~= '0')
    elseif Cmd[1] == '12' then
-      local dPV = MaxOpen
-      if Cmd[2] ~= '0' then
-         dPV = EgtIf( EMT.ROT == -1, EMT.HB, EMT.SB)
-      end
-      SimulMoveAxis( 'PV', dPV, MCH_SIM_STEP.RAPID)
-      SetPVLight( Cmd[2] ~= '0')
+      ExecMovePV( Cmd[2] ~= '0')
    elseif Cmd[1] == '21' then
       local nYDelta = tonumber( Cmd[2])
       local nVDelta = tonumber( Cmd[3])
@@ -912,7 +1032,7 @@ function ExecRemoveScraps()
          for i = nPart, 1, -1 do
             if i ~= nPartMax then
                local b3Vmill = EgtVolZmapGetPartBBoxGlob( vMillId, i - 1, GDB_BB.STANDARD)
-               if b3Vmill:getDimX() < 1200 then
+               if b3Vmill:getDimX() < 1250 then
                   EgtRemoveVolZmapPart( vMillId, i - 1)
                end
             end
@@ -932,7 +1052,7 @@ function ExecUnloading()
       -- li sposto per lasciare spazio al nuovo pezzo
       local nId = EgtGetFirstInGroup( nVmGrpId)
       while nId do
-         EgtMove( nId, Vector3d( 0, EgtIf( BD.RIGHT_LOAD, ( EMT.SB + 50.0), -( EMT.SB + 50.0)), 0), GDB_RT.GLOB)
+         EgtMove( nId, Vector3d( 0, EgtIf( BD.RIGHT_LOAD, ( EMT.ST + 50.0), -( EMT.ST + 50.0)), 0), GDB_RT.GLOB)
          nId = EgtGetNext( nId)
       end
       -- creo un nuovo layer e vi inserisco il nuovo pezzo
@@ -977,6 +1097,176 @@ function ExecUnloading()
    end
 end
 
+---------------------------------------------------------------------
+function CheckClamping( sClampName)
+
+   local nClampId = EgtGetAxisId( sClampName) or GDB_ID.NULL
+   local nClampPathId = EgtGetFirstInGroup( EgtGetFirstNameInGroup( nClampId, 'CLAMP_CHECK') or GDB_ID.NULL)
+   local b3ClampingArea = EgtGetBBoxGlob( nClampPathId or GDB_ID.NULL, GDB_BB.STANDARD)
+   -- se non trovo percorso area di clamping, esco subito
+   if not nClampPathId or not EMT.VMILL or not ClampingCoeffMin then
+      return
+   end
+
+   local function GetCurveListFromIntersection( sPosIntersPlane, sIntersPlane, dDepth)
+      local vCurveListId = {}
+      local vtIntersPlane
+      -- piano di interpolazione 
+      if sIntersPlane == 'X' then
+         vtIntersPlane = X_AX()
+      elseif sIntersPlane == 'Y' then
+         vtIntersPlane = Y_AX()
+      elseif sIntersPlane == 'Z' then
+         vtIntersPlane = Z_AX()
+      end
+
+      for i = 1, #EMT.VMILL do
+         local b3VMill = EgtGetBBoxGlob( EMT.VMILL[i], GDB_BB.EXACT)
+         local ptPosIntersPlane
+         if sPosIntersPlane == 'MIN' then
+            ptPosIntersPlane = b3VMill:getMin() + dDepth * vtIntersPlane
+         elseif sPosIntersPlane == 'MAX' then
+            ptPosIntersPlane = b3VMill:getMax() - dDepth * vtIntersPlane
+         end
+         local nLoopId, nLoopCnt = EgtPlaneVolZmapInters( ptPosIntersPlane, vtIntersPlane, EMT.VMILL[i], CLAMP_CHECK_INTERS, GDB_RT.GLOB)
+         vCurveListId = EgtTableAdd( vCurveListId, nLoopId, nLoopCnt)
+      end
+
+      return vCurveListId
+   end
+
+   local function CalculateIntersectionArea( sPosIntersPlane, sIntersPlane, dDepth)
+      -- test piano frontale
+      local vCurveListId = GetCurveListFromIntersection( sPosIntersPlane, sIntersPlane, dDepth)
+      -- si copia curva intersezione e curva pinza in gruppo di confronto
+      local nFlatSurfId, nFlatSurfCnt = EgtSurfFlatRegion( CLAMP_CHECK_GROUP, vCurveListId)
+      local vFlatSurfId = EgtTableFill( nFlatSurfId, nFlatSurfCnt) or {}
+      local nClampSurfId = EgtSurfFlatRegion( CLAMP_CHECK_GROUP, nClampPathId)
+
+      local dTotalArea = 0
+      local dTotalXLenght = 0
+      for i = 1, #vFlatSurfId do
+         local nTempSurfId = vFlatSurfId[i]
+         EgtSurfFrIntersect( nTempSurfId, nClampSurfId)
+         if nTempSurfId then
+            dTotalArea = dTotalArea + ceil( EgtSurfArea( nTempSurfId) or 0)
+            local b3BoxIntersectionBox = EgtGetBBoxGlob( nTempSurfId, GDB_BB.STANDARD)
+            if b3BoxIntersectionBox then
+               dTotalXLenght = dTotalXLenght + ceil( b3BoxIntersectionBox:getDimX()) -- somma lunghezze (x) delle aree pinzate
+            end
+         end
+      end
+      return dTotalArea, dTotalXLenght
+   end
+
+   -- minima area considerata per un corretto pinzaggio
+   DistZClampToTable = DistZClampToTable or 0
+   --local MinJoin = BD.GetMinJoin( EMT.ST, EMT.HT, EgtIf( EMT.SPLIT, EMT.LT, EMT.LB))
+   UpdateMinJoinDeltaTol( EMT.ST, EMT.HT, EgtIf( EMT.SPLIT, EMT.LT, EMT.LB))
+   local MinZClamping =  min( b3ClampingArea:getDimZ() + DistZClampToTable, EMT.HT) - DistZClampToTable
+   local dMinClamping = ( MinJoin * MinZClamping)
+   -- si moltiplica per un coefficiente minimo sotto al quale si da l'errore di pinzaggio
+   ClampingCoeffMin = EgtClamp( ClampingCoeffMin, 0.01, 1)
+   if MinZClamping > 116 then
+      dMinClamping = MinJoin * 116 + ( pow( MinJoin, 2) / 2)
+      if MinJoin > 280 then
+         dMinClamping = MinJoin * 116 + ( pow( 280, 2) / 2) + ( pow( MinJoin - 280, 2))
+      end
+   end
+   
+   local dMinClampingAreaWarn = dMinClamping * ClampingCoeffMin
+   local dMinClampingAreaErr = dMinClamping * ( ClampingCoeffMin / 3)
+
+   local bError = true
+   local sWrn, sErr
+   local bWriteWarnMessage = false
+   local bWriteErrMessage = false
+   -- controllo faccia frontale
+   local dArea, dXClampedLenght = CalculateIntersectionArea( 'MIN', 'Y', 3)
+   -- ERRORE: pinza troppo poco (meno di 1/3 del minimo richiesto)
+   if dArea and dArea < dMinClampingAreaErr then
+      -- solo se pinza almeno 1cm2, e la somma della lunghezza pinzata è maggiore della lunghezza minima pinzabile da Warning e non errore
+      if dXClampedLenght >= MinJoin * ClampingCoeffMin and dArea > 1000 then 
+         bError = false
+      end
+      -- pinzaggio non fattibile, errore
+      if bError then
+         sErr = 'ERROR CLAMPING ' .. sClampName .. ' : '..tostring( ceil( ( dArea / dMinClampingAreaWarn) * 100))..'% ( '.. tostring( dArea/1000)..'cm2)'
+         bWriteErrMessage = true
+      end
+   end
+   -- WARNING: pinza meno del minimo richiesto
+   if dArea and dArea < dMinClampingAreaWarn and not bWriteErrMessage then
+      sWrn = 'WARNING CLAMPING ' .. sClampName .. ' : '..tostring( ceil( ( dArea / dMinClampingAreaWarn) * 100))..'% ( '.. tostring( dArea/1000)..'cm2)'
+      bWriteWarnMessage = true
+   end
+   EgtEmptyGroup( CLAMP_CHECK_GROUP)
+   EgtEmptyGroup( CLAMP_CHECK_INTERS)
+
+   -- controllo altro lato solo se non sono già in errore
+   if not bWriteErrMessage then
+      -- controllo faccia posteriore
+      dArea, dXClampedLenght = CalculateIntersectionArea( 'MAX', 'Y', 3)
+      -- ERRORE: pinza troppo poco (meno di 1/3 del minimo richiesto)
+      if dArea and dArea < dMinClampingAreaErr then   
+         -- solo se pinza almeno 1cm2, e la somma della lunghezza pinzata è maggiore della lunghezza minima pinzabile da Warning e non errore
+         if dXClampedLenght >= MinJoin * ClampingCoeffMin and dArea > 1000 then 
+            bError = false
+         end
+         -- pinzaggio non fattibile, errore
+         if bError then
+            sErr = 'ERROR CLAMPING ' .. sClampName .. ' : '..tostring( ceil( ( dArea / dMinClampingAreaWarn) * 100))..'% ( '.. tostring( dArea/1000)..'cm2)'
+            bWriteErrMessage = true
+         end
+      end
+      -- WARNING: pinza meno del minimo richiesto
+      if dArea and dArea < dMinClampingAreaWarn and not bWriteWarnMessage and not bWriteErrMessage then
+         sWrn = 'WARNING CLAMPING ' .. sClampName .. ' : '..tostring( ceil( ( dArea / dMinClampingAreaWarn) * 100))..'% ( '.. tostring( dArea/1000)..'cm2)'
+         bWriteWarnMessage = true
+      end
+      EgtEmptyGroup( CLAMP_CHECK_GROUP)
+      EgtEmptyGroup( CLAMP_CHECK_INTERS)
+   end
+
+   if bWriteErrMessage then
+      EmtSetLastError( 1213, sErr, EgtGetEnableUI())
+      EgtOutBox( sErr, 'CLAMPING', 'ERROR', 'OK')
+      EmtSetSimulPause()
+   elseif bWriteWarnMessage then
+      EgtOutLog( sWrn)
+      EgtOutBox( sWrn, 'CLAMPING', 'WARNING', 'OK')
+      EmtSetSimulPause()
+   end
+end
+
+---------------------------------------------------------------------
+function ExecMovePY( bClose)
+   --SimulMoveAxes( 'PY', EgtIf( not bClose, MaxHoOpen, EMT.HB), MCH_SIM_STEP.RAPID)
+   local dPY = MaxOpen
+   if bClose then
+      dPY = EgtIf( EMT.ROT == -1, EMT.HT, EMT.ST)
+   end
+   SimulMoveAxis( 'PY', dPY, MCH_SIM_STEP.RAPID)
+   SetPYLight( bClose)
+   if bClose then
+      CheckClamping( 'PY')
+   end
+end
+
+---------------------------------------------------------------------
+function ExecMovePV( bClose)
+   --EgtIf( not bClose, MaxHoOpen, EMT.HB), MCH_SIM_STEP.RAPID)
+   local dPV = MaxOpen
+   if bClose then
+      dPV = EgtIf( EMT.ROT == -1, EMT.HT, EMT.ST)
+   end
+   SimulMoveAxis( 'PV', dPV, MCH_SIM_STEP.RAPID)
+   SetPVLight( bClose)
+   if bClose then
+      CheckClamping( 'PV')
+   end
+end
+
 ---------------------------------------------------------------------
 function VerifyYSlide( sName1, dVal1, sName2, dVal2)
    -- Se movimento trave agganciata con carrello Y
@@ -1134,11 +1424,11 @@ end
 --   *** ESTIMATION T&L ***
 ---------------------------------------------------------------------
 local ESTIMATION_RAPID_COEFF = EstimationRapidMultiplier or 1
-local RAPID_X_FEED =  75000 / ESTIMATION_RAPID_COEFF    -- mm/min
+local RAPID_X_FEED =  100000 / ESTIMATION_RAPID_COEFF   -- mm/min
 local RAPID_Y_FEED = 100000 / ESTIMATION_RAPID_COEFF    -- mm/min
-local RAPID_Z_FEED =  50000 / ESTIMATION_RAPID_COEFF    -- mm/min
-local RAPID_C_FEED =  15000 / ESTIMATION_RAPID_COEFF    -- deg/min
-local RAPID_B_FEED =  15000 / ESTIMATION_RAPID_COEFF    -- deg/min
+local RAPID_Z_FEED =  100000 / ESTIMATION_RAPID_COEFF   -- mm/min
+local RAPID_C_FEED =  12000 / ESTIMATION_RAPID_COEFF    -- deg/min
+local RAPID_B_FEED =  12000 / ESTIMATION_RAPID_COEFF    -- deg/min
 local RAPID_MIN_T = 0.1 * ESTIMATION_RAPID_COEFF       -- s
 local LOAD_T = 2  * ESTIMATION_RAPID_COEFF              -- s
 local CHAR_ONE_MOVE_T = 1  * ESTIMATION_RAPID_COEFF     -- s
@@ -1150,6 +1440,18 @@ local FALL_T = 2  * ESTIMATION_RAPID_COEFF              -- s
 ---------------------------------------------------------------------
 function OnEstimStart()
    EMT.INCHES = not EgtUiUnitsAreMM()      -- unità di misura mm/inches
+
+   -- TPA
+   if NumericalControl == 'TPA' then
+      EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+      EMT.MAXACC = MaxAcc or 4000    -- accelerazione massima pinze. In realtà è il tempo in millisecondi, quindi MAXACC corrisponde al tempo massimo per raggiungere la velocità desiderata
+      EMT.MINACC = MinAcc or 300     -- accelerazione minima pinze. In realtà è il tempo in millisecondi, quindi MINACC corrisponde al tempo massimo per raggiungere la velocità desiderata
+   -- NUM_PLUS e NUM
+   else
+      EMT.FMAXPINZE = EgtClamp( MaxFeedPinze or 154000, 20000, 160000)  -- feed massima pinze
+      EMT.MAXACC = MaxAcc or ( EMT.FMAXPINZE / ( 60 * 0.3))  -- accelerazione massima pinze
+      EMT.MINACC = MinAcc or ( EMT.FMAXPINZE / ( 60 * 4))    -- accelerazione minima pinze
+   end
 end
 
 ---------------------------------------------------------------------
@@ -1235,6 +1537,15 @@ function OnEstimDispositionEnd()
    EMT.OPEISDISP = false
 end
 
+---------------------------------------------------------------------
+function OnEstimRawMoveData()
+   -- se start del pezzo
+   if IsStartOrRestPhase( EMT.PHASE) then
+      EMT.SPLIT = false
+   end
+   OnRawMoveData()
+end
+
 ---------------------------------------------------------------------
 function OnEstimToolSelect()
    -- reset indice utensile in tabella lunghezze
@@ -1291,6 +1602,12 @@ function OnEstimMachiningEnd()
       EMT.TLE_NAME = nil
       EMT.TLE_TIME = nil
    end
+
+   EMT.MCHUSERNOTES = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   EMT.MCHSPLIT = ( EMT.MCHUSERNOTES:find( 'Split;', 1, true) ~= nil)
+   if EMT.MCHSPLIT then
+      EMT.SPLIT = true
+   end
 end
 
 ---------------------------------------------------------------------
@@ -1421,15 +1738,15 @@ function OnEstimRapid()
    EMT.MCHEXTLEN = EMT.MCHEXTLEN + dLen
    -- calcolo tempo
    local dTime = RAPID_MIN_T
-   local dT1 = abs( dL1) / RAPID_X_FEED * 60
+   local dT1 = CalcMoveTime( abs( dL1), EMT.FMAXPINZE, EMT.SPLIT)
    if dT1 > dTime then dTime = dT1 end
-   local dT2 = abs( dL2) / RAPID_Y_FEED * 60
+   local dT2 = abs( dL2) / ( RAPID_X_FEED / 60) -- CalcMoveTime( abs( dL2), RAPID_X_FEED, EMT.SPLIT)
    if dT2 > dTime then dTime = dT2 end
-   local dT3 = abs( dL3) / RAPID_Z_FEED * 60
+   local dT3 = abs( dL3) / ( RAPID_Z_FEED * 60) -- CalcMoveTime( abs( dL3), RAPID_Z_FEED, EMT.SPLIT)
    if dT3 > dTime then dTime = dT3 end
-   local dT4 = abs( dR1) / RAPID_C_FEED * 60
+   local dT4 = abs( dR1) / ( RAPID_C_FEED / 60)
    if dT4 > dTime then dTime = dT4 end
-   local dT5 = abs( dR2) / RAPID_B_FEED * 60
+   local dT5 = abs( dR2) / ( RAPID_B_FEED / 60)
    if dT5 > dTime then dTime = dT5 end
    EMT.MCHEXTTIME = EMT.MCHEXTTIME + dTime
    EgtOutLog( string.format( '  G0 Len=%.0f Rot=%.0f° Time=%.2f', dLen, abs( dR1) + abs( dR2), dTime), 5)
@@ -1447,7 +1764,7 @@ function OnEstimLinear()
    local dLen = sqrt( dL1 * dL1 + dL2 * dL2 + dL3 * dL3)
    EMT.MCHCUTLEN = EMT.MCHCUTLEN + dLen
    -- calcolo tempo
-   local dTime = dLen / EMT.F * 60
+   local dTime = dLen / ( EMT.F / 60) -- CalcMoveTime( dLen, EMT.F, EMT.SPLIT)
    EMT.MCHCUTTIME = EMT.MCHCUTTIME + dTime
    EgtOutLog( string.format( '  G1 Len=%.0f Time=%.2f', dLen, dTime), 5)
    -- aggiorno valori come precedenti
@@ -1594,6 +1911,70 @@ function GetParkT()
    end
 end
 
+---------------------------------------------------------------------
+function CalcDinamicaPinze_TPA( dH, dS, dL)
+   local MinTempoAcc = EMT.MINACC        -- [ms] ~300
+   local MaxTempoAcc = EMT.MAXACC        -- [ms] ~4000
+   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
+   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
+   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
+   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
+   local TempoAcc = EgtClamp( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito), MinTempoAcc, MaxTempoAcc)
+   local RidFeed = 100 / Massa * 100
+   if RidFeed > 100 then
+      RidFeed = 100
+   elseif RidFeed < 10 then
+      RidFeed = 10
+   end
+   return TempoAcc, MinTempoAcc, RidFeed
+end
+
+---------------------------------------------------------------------
+function CalcDinamicaPinze_NUM( dH, dS, dL)
+   local KgMtCubo= WoodDensity or 550              -- densità legno [Kg / metro cubo]
+   local Massa = ( dH * dS * dL * KgMtCubo ) / 1e9 -- massa [Kg]
+   local FMaxPinze = EMT.FMAXPINZE                 -- Feed massima pinze [mm/min]
+   local ForzaAttrito = 350 * 9.8 * 0.2            -- Forza chiusura pinze [Kgf] * g * Coeff_Attrito -> [N]
+   local TempoAcc = ( ( Massa * FMaxPinze) / ( 60 * ForzaAttrito) / 1000)
+   local AccMaxPinze = EMT.MAXACC
+   local AccPinze = EgtClamp( FMaxPinze / ( 60 * TempoAcc), EMT.MINACC, EMT.MAXACC)
+   local RidFeed = 100 / Massa * 100
+   if RidFeed > 100 then
+      RidFeed = 100
+   elseif RidFeed < 10 then
+      RidFeed = 10
+   end
+   return AccPinze, AccMaxPinze, RidFeed, TempoAcc
+end
+
+---------------------------------------------------------------------
+function CalcMoveTime( dPathLen, dFeed, bIsSplitted)
+   local dTime
+   local dFeedInSec = dFeed / 60
+
+   if NumericalControl == 'TPA' then
+      local dTempoAcc, _, _ = CalcDinamicaPinze_TPA( EMT.HT, EMT.ST, EgtIf( bIsSplitted, EMT.LT, EMT.LB))
+      dTempoAcc = dTempoAcc / 1000
+      -- se si raggiunge la velocità massima
+      if dPathLen >= dFeedInSec * dTempoAcc then
+         dTime = dTempoAcc * 2 + ( ( dPathLen - dFeedInSec * dTempoAcc) / dFeedInSec)
+      else
+         dTime = 2 * sqrt( (dPathLen * dTempoAcc) / dFeedInSec)
+      end
+   else
+      local dAcc, _, _, _ = CalcDinamicaPinze_NUM( EMT.HT, EMT.ST, EgtIf( bIsSplitted, EMT.LT, EMT.LB))
+      -- Caso 1: dFeed raggiunta
+      if dPathLen >= ( dFeedInSec ^ 2) / dAcc then
+         dTime = ( dFeedInSec / dAcc) + ( dPathLen / dFeedInSec)
+      -- Caso 2: dFeed non raggiunta
+      else
+         dTime = 2 * sqrt( dPathLen / dAcc)
+      end
+   end
+
+   return dTime
+end
+
 ---------------------------------------------------------------------
 -- *** END GENERAL ***
 ---------------------------------------------------------------------

Common_FAST.mlse

@@ -7,6 +7,12 @@ EgtEnableDebug( false)
 -- carico librerie
 local BD = require( 'BeamData')
 
+---------------------------------------------------------------------
+-- *** Generic Machinings ***
+---------------------------------------------------------------------
+pcall( require, 'EmtGenMachining')  -- si fa una require con PCALL perchè la libreria è opzionale
+
+
 ---------------------- OnSpecialMoveZup -----------------------------
 ---------------------------------------------------------------------
 function OnSpecialMoveZup()
@@ -25,20 +31,9 @@ end
 
 ---------- OnSpecialApplyDisposition & OnPostApplyMachining ---------
 ----------------------- Costanti ------------------------------------
-local DELTA_TOL_V = 110
-local DELTA_TOL_S = 210
-local DELTA_TOL_L = 410
 local DELTA_TOL_FIXED = 50
-local DeltaTol = DELTA_TOL_S
 local DELTA_SIC = 1
 local AGG_LOAD = 50
-local MIN_JOIN_VV = EgtClamp( MinJoinVV or 75, 60, 150)
-local MIN_JOIN_SS = EgtClamp( MinJoinSS or 100, 80, 275)
-local MIN_JOIN_LS = EgtClamp( MinJoinLS or 290, 250, 400)
-local MIN_JOIN_SL = EgtClamp( MinJoinSL or 100, 80, 400)
-local MIN_JOIN_LL = EgtClamp( MinJoinLL or 400, 300, 600)
-local MinJoin = MIN_JOIN_SS
-local MinOther = abs( MinY) + abs( MaxV) + MinJoin
 
 ----------------------- Variabili -----------------------------------
 local Test = false
@@ -147,53 +142,6 @@ local function IsFirstMachiningAfterRotation( nMchId)
    return ( nRot ~= nPrevRot)
 end
 
----------------------------------------------------------------------
-local function UpdateMinJoinDeltaTol()
-   local L_SMALL = 800
-   local H_V = 90
-   local H_S = 200
-   local H_L = 400
-   local W_V = 90
-   local W_S = 150
-   local W_L = 250
-   if EMC.SB <= W_V and EMC.HB <= H_V then
-      MinJoin = MIN_JOIN_VV
-      DeltaTol = DELTA_TOL_V
-   elseif EMC.LB <= L_SMALL then
-      MinJoin = MIN_JOIN_SS
-      DeltaTol = DELTA_TOL_S
-   else
-      local dMinJoinS
-      local dMinJoinL
-      if EMC.SB <= W_S then
-         dMinJoinS = MIN_JOIN_SS
-         dMinJoinL = MIN_JOIN_LS
-      elseif EMC.SB <= W_L then
-         local Coeff = ( EMC.SB - W_S) / ( W_L - W_S)
-         dMinJoinS = ( 1 - Coeff) * MIN_JOIN_SS + Coeff * MIN_JOIN_SL
-         dMinJoinL = ( 1 - Coeff) * MIN_JOIN_LS + Coeff * MIN_JOIN_LL
-      else
-         dMinJoinS = MIN_JOIN_SL
-         dMinJoinL = MIN_JOIN_LL
-      end
-      if EMC.HB <= H_S then
-         MinJoin = dMinJoinS
-         DeltaTol = DELTA_TOL_S
-      elseif EMC.HB <= H_L then
-         local Coeff = ( EMC.HB - H_S) / ( H_L - H_S)
-         MinJoin = ( 1 - Coeff) * dMinJoinS + Coeff * dMinJoinL
-         DeltaTol = ( 1 - Coeff) * DELTA_TOL_S + Coeff * DELTA_TOL_L
-      else
-         MinJoin = dMinJoinL
-         DeltaTol = DELTA_TOL_L
-      end
-      if EMC.SB < W_V then
-         DeltaTol = DELTA_TOL_V
-      end
-   end
-   MinOther = abs( MinY) + abs( MaxV) + MinJoin
-end
-
 ---------------------------------------------------------------------
 local function GetCUTID()
    -- recupero CUTID del pezzo in lavoro
@@ -361,13 +309,24 @@ function OnSpecialApplyDisposition()
    EMC.ZMIN = b3Raw:getMin():getZ()
 
    -- Aggiorno limiti di presa e tolleranza
-   UpdateMinJoinDeltaTol()
+   UpdateMinJoinDeltaTol( EMC.SB, EMC.HB, EMC.LB)
 
    -- Assegno sovramateriale di testa e ingombro tagli di testa e di coda
    EMC.HOVM = EgtGetInfo( nCurrRawId, 'HOVM', 'd') or 0
    EMC.HCING = EgtGetInfo( nCurrRawId, 'HCING', 'd') or 0
    EMC.TCING = EgtGetInfo( nCurrRawId, 'TCING', 'd') or 0
-   
+
+   -- correggo area non pinzabile in testa o coda in base alle info sulla lavorazione
+   local sNotes = EgtGetMachiningParam( MCH_MP.USERNOTES) or ''
+   local dHCING = tonumber( EgtGetValInNotes( sNotes, 'HCING'))
+   if dHCING then
+      EMC.HCING = max( dHCING, -50)
+   end
+   local dTCING = tonumber( EgtGetValInNotes( sNotes, 'TCING'))
+   if dTCING then
+      EMC.TCING = max( dTCING, -50)
+   end
+
    -- Devo scaricare il pezzo o il grezzo rimasto
    -- Posizione trave
    local dPosT
@@ -511,6 +470,17 @@ function OnPostApplyMachining()
    local bSplitting = ( sNotes:find( 'Split') ~= nil)
    local bPreCut = ( sNotes:find( 'Precut') ~= nil)
    local bCutting = ( sNotes:find( 'Cut') ~= nil)
+
+   -- correggo area non pinzabile in testa o coda in base alle info sulla lavorazione
+   local dHCING = tonumber( EgtGetValInNotes( sNotes, 'HCING'))
+   if dHCING then
+      EMC.HCING = max( dHCING, -50)
+   end
+   local dTCING = tonumber( EgtGetValInNotes( sNotes, 'TCING'))
+   if dTCING then
+      EMC.TCING = max( dTCING, -50)
+   end
+
    local bUnload = IsEndPhase( EMC.PHASE) or IsEnd2Phase( EMC.PHASE)
    if bPreSplit or bPreCut then
       EgtSetInfo( EMC.MCHID, 'IS_PRE', '1')
@@ -628,12 +598,23 @@ function SpecApplyPath( bPreSplit, bSplitting, bPreCut, bCutting, bUnload, bPreR
    EMC.ZMIN = b3Raw:getMin():getZ()
 
    -- Aggiorno limiti di presa e tolleranza
-   UpdateMinJoinDeltaTol()
+   UpdateMinJoinDeltaTol( EMC.SB, EMC.HB, EMC.LB)
 
    -- Recupero sovramateriale di testa e ingombro tagli di testa e di coda
    EMC.HOVM = EgtGetInfo( nCurrRawId, 'HOVM', 'd') or 0
    EMC.HCING = EgtGetInfo( nCurrRawId, 'HCING', 'd') or 0
    EMC.TCING = EgtGetInfo( nCurrRawId, 'TCING', 'd') or 0
+   
+   -- correggo area non pinzabile in testa o coda in base alle info sulla lavorazione
+   local sNotes = EgtGetMachiningParam( MCH_MP.USERNOTES)
+   local dHCING = tonumber( EgtGetValInNotes( sNotes, 'HCING'))
+   if dHCING then
+      EMC.HCING = max( dHCING, -50)
+   end
+   local dTCING = tonumber( EgtGetValInNotes( sNotes, 'TCING'))
+   if dTCING then
+      EMC.TCING = max( dTCING, -50)
+   end
 
    -- Calcolo dell'ingombro della lavorazione
    local dDistFront, dDistBack = SpecialCalcMachiningEncumbrance( EMC.MCHID, bPreCut)
@@ -892,7 +873,7 @@ function SpecCalcEncumbrance( vtTool, vtArm, ptMin, ptMax, bSaw, bChain, dTLen,
    local dHeadBack = 350
    if bSaw then
       if vtTool:getX() > 0 and abs( vtTool:getY()) < 0.088 and abs( vtTool:getZ()) < 0.088 then
-         dHeadBack = 50 + 0.5 * dTDiam * sqrt( 1 - vtTool:getX() * vtTool:getX())
+         dHeadBack = 50 + 0.5 * dTDiam * sqrt( 1 - vtTool:getX() * vtTool:getX()) + EgtIf( EMC.CNT == 1, 10, 0)
       elseif abs( vtTool:getZ()) < 0.26 and abs( vtTool:getX()) < 0.35 then
          dHeadBack = EgtIf( vtArm:getX() < 0, 540, 350)
       elseif abs( vtTool:getZ()) < 0.26 and abs( vtTool:getX()) < 0.71 then
@@ -983,7 +964,7 @@ function SpecCalcEncumbrance( vtTool, vtArm, ptMin, ptMax, bSaw, bChain, dTLen,
    local dHeadFront = 350
    if bSaw then
       if vtTool:getX() < 0 and abs( vtTool:getY()) < 0.088 and abs( vtTool:getZ()) < 0.088 then
-         dHeadFront = 50 + 0.5 * dTDiam * sqrt( 1 - vtTool:getX() * vtTool:getX())
+         dHeadFront = 50 + 0.5 * dTDiam * sqrt( 1 - vtTool:getX() * vtTool:getX()) + EgtIf( EMC.CNT == 1, 10, 0)
       elseif abs( vtTool:getZ()) < 0.26 and abs( vtTool:getX()) < 0.35 then
          dHeadFront = EgtIf( vtArm:getX() > 0, 540, 350)
       elseif abs( vtTool:getZ()) < 0.26 and abs( vtTool:getX()) < 0.71 then
@@ -1603,7 +1584,9 @@ function SpecAdjustCarriages( vCmd, dTPosI, dYDeltaI, dVDeltaI, dTPosF, dYDeltaF
       --    * deve effettivamente spostarsi
       --    * non si arriva da gestione passo del pellegrino
       --    * se riesce a raggiungere la posizione con le corse a disposizione per come sono posizionate le morse attualmente
-      if ( dYDeltaI - dVDeltaF) + 10 * GEO.EPS_SMALL >= MyMinY - MaxV and abs( dVDeltaF - dVDeltaI) > 10 * GEO.EPS_SMALL and  not EMC.PILGRIMSTEP and
+      if ( dYDeltaI - dVDeltaF) + 10 * GEO.EPS_SMALL >= MyMinY - MaxV and
+         ( abs( dVDeltaF - dVDeltaI) > 10 * GEO.EPS_SMALL or not EMC.VDELTA) and
+         not EMC.PILGRIMSTEP and
          ( dVDeltaF - dVDeltaI > MinV - dVPosI + MyMinY - dYPosI) then
          table.insert( vCmd, { 0, 'Direct-V-Y'})
          -- se l'altra morsa non era in presa, vado a pinzare il pezzo
@@ -1682,7 +1665,7 @@ function SpecAdjustCarriages( vCmd, dTPosI, dYDeltaI, dVDeltaI, dTPosF, dYDeltaF
             if abs( dYDeltaF - dYDeltaI) > 10 * GEO.EPS_SMALL then
                table.insert( vCmd, { 11, 0})
                dYPosA = max( MyMinY, dTPosI + dYDeltaF)
-               dTPosA = -( dYPosA + dVDeltaF)
+               dTPosA = dYPosA - dYDeltaF
                dVPosA = dTPosA + dVDeltaF
                table.insert( vCmd, { 3, 'Y', dYPosA , 'T', dTPosA, 'V', dVPosA})
                table.insert( vCmd, { 11, CalcCharStatus( 'Y', dYDeltaF)})
@@ -1708,7 +1691,9 @@ function SpecAdjustCarriages( vCmd, dTPosI, dYDeltaI, dVDeltaI, dTPosF, dYDeltaF
       --    * deve effettivamente spostarsi
       --    * non si arriva da gestione passo del pellegrino
       --    * se riesce a raggiungere la posizione con le corse a disposizione per come sono posizionate le morse attualmente
-      elseif ( dYDeltaF - dVDeltaI) + 10 * GEO.EPS_SMALL >= MyMinY - MaxV and abs( dYDeltaF - dYDeltaI) > 10 * GEO.EPS_SMALL and  not EMC.PILGRIMSTEP and
+      elseif ( dYDeltaF - dVDeltaI) + 10 * GEO.EPS_SMALL >= MyMinY - MaxV and 
+             ( abs( dYDeltaF - dYDeltaI) > 10 * GEO.EPS_SMALL or not EMC.YDELTA) and
+             not EMC.PILGRIMSTEP and
              ( dYDeltaF - dYDeltaI < MaxY - dYPosI + MaxV - dVPosI) then
          table.insert( vCmd, { 0, 'Direct-Y-V'})
          -- se l'altra morsa non era in presa, vado a pinzare il pezzo

Essetre-FASTrl.ini

@@ -34,8 +34,15 @@ Milling=1
 Pocketing=1
 Mortising=1
 Chiseling=0
-SawRoughing=0
-SawFinishing=0
+GenMachining=0
+SurfRoughing=1
+SurfFinishing=1
+5AxMilling=1
+
+[5AxMilling]
+5AxScript1=5AxProject
+5AxScript2=5AxPocketProject
+5AxScript3=5AxCylProject
 
 [Machining]
 InitScript=InitMach.lua

Essetre-FASTrl.mlde

@@ -10,10 +10,10 @@
 require( 'EmtGenerator')
 EgtEnableDebug( false)
 
-PP_VER = '2.7a3'
-PP_NVER = '2.7.1.3'
-MIN_MACH_VER = '2.5k1'
-MACH_NAME = 'Essetre-FASTrl'
+PP_VER = '3.1a2'
+PP_NVER = '3.1.1.2'
+MIN_MACH_VER = '2.7j1'
+MACH_NAME =  EgtGetCurrMachineName()
 
 -- Carico i dati globali
 local sMachDir = EgtGetCurrMachineDir()
@@ -76,8 +76,19 @@ BeamHeightForFixRot = 9999                     -- per abilitare assegnare 500
 NewTopC = true
 SafeXRotAxes = -150
 AggreBlockHaus = false
+SecondToolChanger = false
 EstimationRapidMultiplier = 1
+DistZClampToTable = 5                             -- distanza tra la tavola e il punto più basso della morsa
+ClampingCoeffMin = nil                             -- coefficiente di fissaggio, se 0 o nil non fa controllo, per il momento da inizializzare da Ts3Data
+MinJoinVV = 75
+MinJoinSS = 100
+MinJoinLS = 290
+MinJoinSL = 100
+MinJoinLL = 400
 
+-- costanti dimensioni utensili
+LONG_TOOL_MINLEN = 221
+BIG_TOOL_DIAM = 300
 
 -- leggo e aggiorno con parametri da BeamData
 if BD then
@@ -133,18 +144,32 @@ if EgtExistsFile( sData) then
          if Machine.Offsets.NOULOAD then MaxUnloadLen = Machine.Offsets.NOULOAD end
          if Machine.Offsets.DEFTCPOS then DefTcPos = ( 'T' .. Machine.Offsets.DEFTCPOS) end
          if Machine.Offsets.WOOD_DENSITY then WoodDensity = Machine.Offsets.WOOD_DENSITY end
-         if Machine.Offsets.MIN_JOIN_VV then MinJoinVV = Machine.Offsets.MIN_JOIN_VV end
-         if Machine.Offsets.MIN_JOIN_SS then MinJoinSS = Machine.Offsets.MIN_JOIN_SS end
-         if Machine.Offsets.MIN_JOIN_LS then MinJoinLS = Machine.Offsets.MIN_JOIN_LS end
-         if Machine.Offsets.MIN_JOIN_SL then MinJoinSL = Machine.Offsets.MIN_JOIN_SL end
-         if Machine.Offsets.MIN_JOIN_LL then MinJoinLL = Machine.Offsets.MIN_JOIN_LL end
+         if Machine.Offsets.MIN_JOIN_VV then MinJoinVV = EgtClamp( Machine.Offsets.MIN_JOIN_VV, 60, 150) end
+         if Machine.Offsets.MIN_JOIN_SS then MinJoinSS = EgtClamp( Machine.Offsets.MIN_JOIN_SS, 80, 275) end
+         if Machine.Offsets.MIN_JOIN_LS then MinJoinLS = EgtClamp( Machine.Offsets.MIN_JOIN_LS, 250, 400) end
+         if Machine.Offsets.MIN_JOIN_SL then MinJoinSL = EgtClamp( Machine.Offsets.MIN_JOIN_SL, 80, 400) end
+         if Machine.Offsets.MIN_JOIN_LL then MinJoinLL = EgtClamp( Machine.Offsets.MIN_JOIN_LL, 300, 600) end
+         if Machine.Offsets.MAXFEEDPINZE then MaxFeedPinze = Machine.Offsets.MAXFEEDPINZE end
+         if Machine.Offsets.MAXACC then MaxAcc = Machine.Offsets.MAXACC end
+         if Machine.Offsets.MINACC then MinAcc = Machine.Offsets.MINACC end
          if Machine.Offsets.NEWTOPC then NewTopC = ( Machine.Offsets.NEWTOPC == 1) end
          if Machine.Offsets.AGGRE_BH then AggreBlockHaus = ( Machine.Offsets.AGGRE_BH == 1) end
+         if Machine.Offsets.SEC_TC then SecondToolChanger = ( Machine.Offsets.SEC_TC == 1) end
          if Machine.Offsets.COEFF_STIMATEMPI and Machine.Offsets.COEFF_STIMATEMPI > 0 then EstimationRapidMultiplier = Machine.Offsets.COEFF_STIMATEMPI end
+         if Machine.Offsets.MAX_HEIGHT_ROT_B_ABOVE then BeamHeightForFixRot = Machine.Offsets.MAX_HEIGHT_ROT_B_ABOVE end
+         if Machine.Offsets.COEFF_CLAMP_CHECK then ClampingCoeffMin = Machine.Offsets.COEFF_CLAMP_CHECK end
       end
    end
 end
 if SpecialBH then SecondSupport = 0 end
+-- Aggiorno valori MinJoin
+MinJoin = MinJoinSS
+MinOther = abs( MinY) + abs( MaxV) + MinJoin
+DeltaTol = 210
+
+-- compongo i gruppi appartenenti alla base
+local sBaseAux = {'BASE/SOLID', 'BASE/TC', 'BASE/SIGN', 'BASE/COLLISION'}
+if SecondToolChanger then table.insert( sBaseAux, 5, 'BASE/TC2') end
 
 EmtGeneral {
       File='Essetre-FASTrl.nge',
@@ -159,7 +184,7 @@ EmtGeneral {
 local BaseId = EmtBase {
       Name = 'Base',
       Geo='BASE/GEO',
-      Aux={'BASE/SOLID', 'BASE/TC', 'BASE/SIGN', 'BASE/COLLISION'}}
+      Aux = sBaseAux}
 local XId = EmtAxis {
       Name = 'X',
       Parent = 'Base',
@@ -190,7 +215,7 @@ local CId = EmtAxis {
       Stroke = {MinC, MaxC},
       Home = 0,
       Geo = 'C_AXIS/GEO',
-      Aux = {'C_AXIS/SOLID', 'C_AXIS/COLLISION'}}
+      Aux = {'C_AXIS/SOLID', 'C_AXIS/COLLISION', 'C_AXIS/COLLISION2'}}
 if NewTopC then
    local vtMove = Vector3d( 65,0,0)
    local SolidArmId = EgtGetFirstNameInGroup( EgtGetFirstNameInGroup( CId, 'SOLID'), 'ARM')
@@ -205,9 +230,13 @@ if NewTopC then
    local CollTopId = EgtGetFirstNameInGroup( EgtGetFirstNameInGroup( CId, 'COLLISION'), 'TOP')
    EgtMove( CollTopId, vtMove, GDB_RT.GLOB)
    EgtSetName( CollTopId, 'BOX')
+   local RefId = CollTopId + EgtGetInfo( CollTopId, 'Frame', 'i')
+   EgtSetInfo( RefId, 'CollSkip', 'C_TOP')
 else
    local CollTopId = EgtGetFirstNameInGroup( EgtGetFirstNameInGroup( CId, 'COLLISION'), 'TOP')
    EgtSetName( CollTopId, 'BOX')
+   local RefId = CollTopId + EgtGetInfo( CollTopId, 'Frame', 'i')
+   EgtSetInfo( RefId, 'CollSkip', 'C_TOP')
 end
 EmtAxis {
       Name = 'B',
@@ -340,7 +369,7 @@ local PYId = EmtAxis {
       Stroke = { 0, MaxOpen},
       Home = MaxOpen,
       Geo = 'PY_AXIS/GEO',
-      Aux = {'PY_AXIS/SOLID', 'PY_AXIS/COLLISION'}}
+      Aux = {'PY_AXIS/SOLID', 'PY_AXIS/COLLISION', 'PY_AXIS/CLAMP_CHECK'}}
 local VId = EmtAxis {
       Name = 'V',
       Parent = 'Base',
@@ -360,7 +389,7 @@ local PVId = EmtAxis {
       Stroke = { 0, MaxOpen},
       Home = MaxOpen,
       Geo = 'PV_AXIS/GEO',
-      Aux = {'PV_AXIS/SOLID', 'PV_AXIS/COLLISION'}}
+      Aux = {'PV_AXIS/SOLID', 'PV_AXIS/COLLISION', 'PV_AXIS/CLAMP_CHECK'}}
 EmtAxis {
       Name = 'T',
       Parent = 'Base',
@@ -469,44 +498,120 @@ else
          Geo = 'BASE/T11'}
 end
 
-
-if not SpecialBH then
+-- ToolChanger 2
+if SecondToolChanger then
    EmtTcPos {
-         Name = 'T101',
+         Name = 'T21',
          Parent = 'Base',
-         Pos = Point3d( 510.4, -113.2, -160.8),
+         Pos = Point3d( 503.2, -88.0, 172.5),
          TDir = -X_AX(),
-         ADir = Z_AX(),
-         Geo = 'BASE/T101'}
+         ADir = -Y_AX(),
+         Geo = 'BASE/T21'}
+   EmtTcPos {
+         Name = 'T22',
+         Parent = 'Base',
+         Pos = Point3d( 503.2, -88.0, 67.5),
+         TDir = -X_AX(),
+         ADir = -Y_AX(),
+         Geo = 'BASE/T22'}
+   EmtTcPos {
+         Name = 'T23',
+         Parent = 'Base',
+         Pos = Point3d( 503.2, -88.0, -37.5),
+         TDir = -X_AX(),
+         ADir = -Y_AX(),
+         Geo = 'BASE/T23'}
+   EmtTcPos {
+         Name = 'T24',
+         Parent = 'Base',
+         Pos = Point3d( 503.2, -88.0, -142.5),
+         TDir = -X_AX(),
+         ADir = -Y_AX(),
+         Geo = 'BASE/T24'}
+   EmtTcPos {
+         Name = 'T25',
+         Parent = 'Base',
+         Pos = Point3d( 503.2, -88.0, -247.5),
+         TDir = -X_AX(),
+         ADir = -Y_AX(),
+         Geo = 'BASE/T25'}
+   EmtTcPos {
+         Name = 'T26',
+         Parent = 'Base',
+         Pos = Point3d( 503.2, -88.0, -352.5),
+         TDir = -X_AX(),
+         ADir = -Y_AX(),
+         Geo = 'BASE/T26'}
+   EmtTcPos {
+         Name = 'T27',
+         Parent = 'Base',
+         Pos = Point3d( 503.2, -88.0, -457.5),
+         TDir = -X_AX(),
+         ADir = -Y_AX(),
+         Geo = 'BASE/T27'}
+   EmtTcPos {
+         Name = 'T28',
+         Parent = 'Base',
+         Pos = Point3d( 503.2, -88.0, -562.5),
+         TDir = -X_AX(),
+         ADir = -Y_AX(),
+         Geo = 'BASE/T28'}
 else
-   EmtTcPos {
-         Name = 'T101',
-         Parent = 'Base',
-         Pos = Point3d( 510.4, -113.2, -1160.8),
-         TDir = -X_AX(),
-         ADir = Z_AX(),
-         Geo = 'BASE/T101S'}
+   if not SpecialBH then
+      EmtTcPos {
+            Name = 'T101',
+            Parent = 'Base',
+            Pos = Point3d( 510.4, -113.2, -160.8),
+            TDir = -X_AX(),
+            ADir = Z_AX(),
+            Geo = 'BASE/T101'}
+   end
+   if SecondSupport == 1 then
+      -- supporto per punta
+      EmtTcPos {
+            Name = 'T111',
+            Parent = 'Base',
+            Pos = Point3d( 510.4, -113.2, -329.8),
+            TDir = Z_AX(),
+            ADir = -X_AX(),
+            Geo = 'BASE/T111'}
+   elseif SecondSupport == 2 then
+      -- supporto per mortasatrice
+      local TcpSsId = EmtTcPos {
+                           Name = 'T111',
+                           Parent = 'Base',
+                           Pos = Point3d( 510.4, -113.2, -430.8),
+                           TDir = X_AX(),
+                           ADir = Z_AX(),
+                           Geo = 'BASE/T111M'}
+      EgtSetInfo( TcpSsId, 'Mortiser', true)
+   end
+   if SpecialBH then
+      EmtTcPos {
+            Name = 'T111',
+            Parent = 'Base',
+            Pos = Point3d( 810.4, -113.2, -329.8),
+            TDir = -Y_AX(),
+            ADir = -X_AX(),
+            Geo = 'BASE/T111S'}
+   end
 end
-if SecondSupport == 1 then
-   -- supporto per punta
-   EmtTcPos {
-         Name = 'T111',
-         Parent = 'Base',
-         Pos = Point3d( 510.4, -113.2, -329.8),
-         TDir = Z_AX(),
-         ADir = -X_AX(),
-         Geo = 'BASE/T111'}
-elseif SecondSupport == 2 then
-   -- supporto per mortasatrice
+
+-- motosega in caso di magazzino 2 o SpecialBH
+if SpecialBH or SecondToolChanger then
    local TcpSsId = EmtTcPos {
-                        Name = 'T111',
+                        Name = 'T101',
                         Parent = 'Base',
-                        Pos = Point3d( 510.4, -113.2, -430.8),
-                        TDir = X_AX(),
+                        Pos = Point3d( 510.4, -113.2, -1160.8),
+                        TDir = -X_AX(),
                         ADir = Z_AX(),
-                        Geo = 'BASE/T111M'}
-   EgtSetInfo( TcpSsId, 'Mortiser', true)
-elseif SecondSupport == 3 then
+                        Geo = 'BASE/T101S'}
+   -- spostamento in caso di magazzino 2
+   if SecondToolChanger then
+      EgtMove( TcpSsId, Vector3d( 0, 0, 140), GDB_RT.GLOB)
+   end
+end
+if SecondSupport == 3 then
    -- supporto per rinvio angolare
    local TcpSsId = EmtTcPos {
                         Name = 'T91',
@@ -519,15 +624,9 @@ elseif SecondSupport == 3 then
                         ADir = Z_AX(),
                         Geo = 'BASE/T91',
                         Aux = 'BASE/T91_HS'}
-end
-if SpecialBH then
-   EmtTcPos {
-         Name = 'T111',
-         Parent = 'Base',
-         Pos = Point3d( 810.4, -113.2, -329.8),
-         TDir = -Y_AX(),
-         ADir = -X_AX(),
-         Geo = 'BASE/T111S'}
+   if SecondToolChanger then
+      EgtMove( TcpSsId, Vector3d( 0, 0, -900), GDB_RT.GLOB)
+   end
 end
 
 -- Aggiusto posizioni geometriche
@@ -541,10 +640,12 @@ EgtMove( EgtGetFirstNameInGroup( YId, 'SOLID'), vtMove, GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( YId, 'COLLISION'), vtMove, GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( PYId, 'SOLID'), vtMove, GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( PYId, 'COLLISION'), vtMove, GDB_RT.GLOB)
+EgtMove( EgtGetFirstNameInGroup( PYId, 'CLAMP_CHECK'), vtMove + Vector3d(0,0,DistZClampToTable), GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( VId, 'SOLID'), vtMove, GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( VId, 'COLLISION'), vtMove, GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( PVId, 'SOLID'), vtMove, GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( PVId, 'COLLISION'), vtMove, GDB_RT.GLOB)
+EgtMove( EgtGetFirstNameInGroup( PVId, 'CLAMP_CHECK'), vtMove + Vector3d(0,0,DistZClampToTable), GDB_RT.GLOB)
 EgtMove( EgtGetFirstNameInGroup( XId, 'SOLID'), vtMoveX, GDB_RT.GLOB)
 
 -- Assegno identificativi alle spie delle morse
@@ -559,24 +660,33 @@ PVLightId = EgtGetFirstNameInGroup( EgtGetFirstNameInGroup( PVId, 'SOLID') or GD
 ---------------------------------------------------------------------
 function OnSetHead()
    -- se testa lama
-   if EMC.HEAD == 'H2' then
-      EmtModifyAxisDirection( 'B', VectorFromRotated( X_AX(), Z_AX(), -SawCOffs))
-      EmtModifyAxisHome( 'C', 0)
-   -- se sega a catena
-   elseif EMC.HEAD == 'H3' then
-      EmtModifyAxisDirection( 'B', X_AX())
-      EmtModifyAxisHome( 'C', 180)
-      local dDist = EgtIf( EMC.DIST and abs( EMC.DIST) > 1, EMC.DIST, ChSawLen)
-      EmtModifyExitPosition( EMC.HEAD, EMC.EXIT, Point3d( 0, 0, -dDist))
-      if not EMC.VER or EMC.VER < '2.5h2' then
-         local vtMove = Point3d( 0, 0, -dDist) - Point3d( EMC.EXITPOS)
-         local ExitId = EgtGetFirstNameInGroup( EgtGetHeadId( EMC.HEAD), 'T'..tostring( EMC.EXIT))
-         EgtMove( ExitId, vtMove)
+   if EMC.HEAD == 'H1' then
+      if EMC.TOTLEN and EMC.TOTLEN < LONG_TOOL_MINLEN then
+         EmtModifyAxisStroke( 'B', {MinB, MaxB})
+      else
+         EmtModifyAxisStroke( 'B', {-140, 140})
       end
-   -- altrimenti
    else
-      EmtModifyAxisDirection( 'B', X_AX())
-      EmtModifyAxisHome( 'C', 0)
+      EmtModifyAxisStroke( 'B', {MinB, MaxB})
+      if EMC.HEAD == 'H2' then
+         EmtModifyAxisDirection( 'B', VectorFromRotated( X_AX(), Z_AX(), -SawCOffs))
+         EmtModifyAxisHome( 'C', 0)
+      -- se sega a catena
+      elseif EMC.HEAD == 'H3' then
+         EmtModifyAxisDirection( 'B', X_AX())
+         EmtModifyAxisHome( 'C', 180)
+         local dDist = EgtIf( EMC.DIST and abs( EMC.DIST) > 1, EMC.DIST, ChSawLen)
+         EmtModifyExitPosition( EMC.HEAD, EMC.EXIT, Point3d( 0, 0, -dDist))
+         if not EMC.VER or EMC.VER < '2.5h2' then
+            local vtMove = Point3d( 0, 0, -dDist) - Point3d( EMC.EXITPOS)
+            local ExitId = EgtGetFirstNameInGroup( EgtGetHeadId( EMC.HEAD), 'T'..tostring( EMC.EXIT))
+            EgtMove( ExitId, vtMove)
+         end
+      -- altrimenti
+      else
+         EmtModifyAxisDirection( 'B', X_AX())
+         EmtModifyAxisHome( 'C', 0)
+      end
    end
 end
 
@@ -618,6 +728,52 @@ function GetPVLight()
    return ( EgtGetInfo( PVLightId, 'On') == '1')
 end
 
+---------------------------------------------------------------------
+---------------------------- Cambio Utensile ------------------------
+function GetTCSet( sTcPos)
+   -- TC 1
+   if sTcPos == 'T1' or sTcPos == 'T2' or sTcPos == 'T3' or sTcPos == 'T4' or sTcPos == 'T5' or
+      sTcPos == 'T6' or sTcPos == 'T7' or sTcPos == 'T8' or sTcPos == 'T9' or sTcPos == 'T10' or sTcPos == 'T11' then
+      return 1
+   -- TC 2
+   elseif sTcPos == 'T21' or sTcPos == 'T22' or sTcPos == 'T23' or sTcPos == 'T24' or
+          sTcPos == 'T25' or sTcPos == 'T26' or sTcPos == 'T27' or sTcPos == 'T28' then
+      return 2
+   end
+end
+
+---------------------------------------------------------------------
+-- Funzione per impostare la posizione del rinvio flottante
+function SetFloatPos( sHead, dPos)
+   -- recupero Id testa
+   local nHeadId = EgtGetHeadId( sHead)
+   if not nHeadId then return false end
+   -- se ci sono entita' flottanti nel ToolHolder
+   local nRefId = EgtGetFirstNameInGroup( nHeadId, '_T1')
+   local vtTool = EgtFR( nRefId, GDB_ID.ROOT):getVersZ() 
+   local nObjId =  EgtGetFirstGroupInGroup( EgtGetFirstNameInGroup( nHeadId, 'T1'))
+   local FloatEntities = EgtGetInfoInGroup( nObjId, 'Float')
+   if FloatEntities and #FloatEntities > 0 then
+      -- il porta-utensile flottante non puo' comprimersi piu' di 10mm
+      if dPos > 10 then
+         local sErr = 'Floating Ring compressed more than 10mm'
+         EmtSetLastError( 1222, sErr)
+         EgtOutLog( 'Error : ' .. sErr, 1)
+      end
+      local dFloat = EgtGetInfo( FloatEntities[1], 'Float', 'd')
+      if abs( dPos - dFloat) > 10 * GEO.EPS_SMALL then
+         local vtMove = ( dPos - dFloat) * vtTool
+         -- sposto tutte le entita' flottanti
+         for i = 1, #FloatEntities do
+            EgtMove( FloatEntities[i], vtMove, GDB_RT.GLOB)
+            EgtSetInfo( FloatEntities[i], 'Float', dPos)
+         end
+      end
+      return true
+   end
+   return false
+end
+
 ---------------------------------------------------------------------
 -- Funzione per resettare tutte le attivazioni della macchina
 function OnResetMachine()
@@ -625,6 +781,7 @@ function OnResetMachine()
    EmtUnlinkAllFixturesFromGroups()
    SetPYLight( false)
    SetPVLight( false)
+   SetFloatPos( 'H1', 0)
    -- nascondo Vmill
    local nRawId = EgtGetFirstRawPart()
    while nRawId do
@@ -638,3 +795,53 @@ function OnResetMachine()
    end
    EgtSetStatus( EgtGetFirstNameInGroup( GDB_ID.ROOT, 'VMill') or GDB_ID.NULL, GDB_ST.OFF)
 end
+
+---------------------------------------------------------------------
+function UpdateMinJoinDeltaTol( SB, HB, LB)
+   local L_SMALL = 800
+   local H_V = 90
+   local H_S = 200
+   local H_L = 400
+   local W_V = 90
+   local W_S = 150
+   local W_L = 250
+   local DELTA_TOL_S = 210
+   local DELTA_TOL_V = 110
+   local DELTA_TOL_L = 410
+   if SB <= W_V and HB <= H_V then
+      MinJoin = MinJoinVV
+      DeltaTol = DELTA_TOL_V
+   elseif LB <= L_SMALL then
+      MinJoin = MinJoinSS
+      DeltaTol = DELTA_TOL_S
+   else
+      local dMinJoinS
+      local dMinJoinL
+      if SB <= W_S then
+         dMinJoinS = MinJoinSS
+         dMinJoinL = MinJoinLS
+      elseif SB <= W_L then
+         local Coeff = ( SB - W_S) / ( W_L - W_S)
+         dMinJoinS = ( 1 - Coeff) * MinJoinSS + Coeff * MinJoinSL
+         dMinJoinL = ( 1 - Coeff) * MinJoinLS + Coeff * MinJoinLL
+      else
+         dMinJoinS = MinJoinSL
+         dMinJoinL = MinJoinLL
+      end
+      if HB <= H_S then
+         MinJoin = dMinJoinS
+         DeltaTol = DELTA_TOL_S
+      elseif HB <= H_L then
+         local Coeff = ( HB - H_S) / ( H_L - H_S)
+         MinJoin = ( 1 - Coeff) * dMinJoinS + Coeff * dMinJoinL
+         DeltaTol = ( 1 - Coeff) * DELTA_TOL_S + Coeff * DELTA_TOL_L
+      else
+         MinJoin = dMinJoinL
+         DeltaTol = DELTA_TOL_L
+      end
+      if SB < W_V then
+         DeltaTol = DELTA_TOL_V
+      end
+   end
+   MinOther = abs( MinY) + abs( MaxV) + MinJoin
+end

MachNotes.ini

@@ -7,21 +7,22 @@
 [Sawing]
 
 [Milling]
-0=d,MaxElev,0
+0=l,MaxElev,0
 1=d,OutRaw,0
-2=d,SideElev,0
+2=l,SideElev,0
 3=d,TrimExt,0
-4=sr,VtFaceUse,0,0,0
+4=s,VtFaceUse,0,0,0
+5=s,EdgesFaceUse,0
 
 [Pocketing]
-0=d,MaxElev,0
+0=l,MaxElev,0
 1=b,Open,0
-2=d,OpenMinSave,0
+2=d,OpenMinSafe,0
 3=d,OpenOutRaw,0
-4=d,MaxOptSize,0
+4=l,MaxOptSize,0
 
 [Mortising]
-0=d,MaxElev,0
+0=l,MaxElev,0
 
 [Chiseling]
 
@@ -30,21 +31,28 @@
 [SawFinishing]
 
 [GenMachining]
-0=l,LinTol,0.1
-1=l,MaxLen,2
-2=s,Type,ZigZag
-3=d,SideAng,90
-4=l,Step,10
-5=l,OffsProj,0
-6=l,LiTang,0
-7=l,LiOrth,0
-8=l,LiElev,0
-9=l,LoTang,0
-10=l,LoOrth,0
-11=l,LoElev,0
-12=b,DirFromGuide,1
 
 [SurfRoughing]
+0=l,MaxElev,1000
+1=b,PlaneZ,0
 
 [SurfFinishing]
 0=b,SkipMaxDown,1
+
+[5AxMilling]
+0=l,LinTol,0.01
+1=l,MaxLen,10
+2=s,Type,ZigZag
+3=d,SideAng,90
+4=l,Step,10
+5=d,AngIni,-90
+6=d,AngFin,90
+7=l,LiTang,0
+8=l,LiOrth,0
+9=l,LiElev,0
+10=l,LoTang,0
+11=l,LoOrth,0
+12=l,LoElev,0
+13=b,DirFromGuide,0
+14=b,SurfAvoid,0
+

Scripts/SetUp.lua

@@ -1,4 +1,4 @@
--- Gestione attrezzaggio per Essetre-FAST - 2020/04/26
+-- Gestione attrezzaggio per Essetre-FAST - 2022/06/16
 
 -- Intestazioni
 require( 'EgtBase')
@@ -24,9 +24,7 @@ local INVALIDPOS = ""
 local POS = "Pos"
 
 -- Geom Set
-local GS = {}
-
-local bAggreBlockHaus = ( EgtGetHeadId( 'H7') ~= nil)
+local GS = {{"H1", "H7"}}
 
 -- Configurazione posizioni
 local PositionTable={{Pos = "Pos1",  TcPos = "T1",  Head = "H1", Group = "G1"},
@@ -39,23 +37,40 @@ local PositionTable={{Pos = "Pos1",  TcPos = "T1",  Head = "H1", Group = "G1"},
                      {Pos = "Pos8",  TcPos = "T8",  Head = "H1", Group = "G1"},
                      {Pos = "Pos9",  TcPos = "T9",  Head = "H1", Group = "G1"},
                      {Pos = "Pos10", TcPos = "T10", Head = "H1", Group = "G1"},
-                     {Pos = "Pos11", TcPos = "T11", Head = EgtIf( bAggreBlockHaus, "H7", "H1"), Group = "G1"},
+                     {Pos = "Pos11", TcPos = "T11", Head = "H1", Group = "G1"},
                      {Pos = "Pos12", TcPos = "T42", Head = "H2", Group = "G1"},
                      {Pos = "Pos13", TcPos = "T101", Head = "H3", Group = "G2"}}
-local SecSuppId = EgtGetTcPosId( 'T111')
-if SecSuppId then
-   local bMortiser = EgtGetInfo( SecSuppId, 'Mortiser', 'b')
-   if bMortiser then
-      table.insert( PositionTable, {Pos = "Pos14", TcPos = "T111", Head = "H3", Group = "G2"})
-   else
-      table.insert( PositionTable, {Pos = "Pos14", TcPos = "T111", Head = "H1", Group = "G2"})
+
+local IsTC2Active = ( EgtGetFirstNameInGroup( EgtGetBaseId( 'Base'), 'TC2') ~= nil)
+if IsTC2Active then
+   local PositionTableTC2={{Pos = "Pos14",  TcPos = "T21",  Head = "H1", Group = "G3"},
+                           {Pos = "Pos15",  TcPos = "T22",  Head = "H1", Group = "G3"},
+                           {Pos = "Pos16",  TcPos = "T23",  Head = "H1", Group = "G3"},
+                           {Pos = "Pos17",  TcPos = "T24",  Head = "H1", Group = "G3"},
+                           {Pos = "Pos18",  TcPos = "T25",  Head = "H1", Group = "G3"},
+                           {Pos = "Pos19",  TcPos = "T26",  Head = "H1", Group = "G3"},
+                           {Pos = "Pos20",  TcPos = "T27",  Head = "H1", Group = "G3"},
+                           {Pos = "Pos21",  TcPos = "T28",  Head = "H1", Group = "G3"}}
+   if EgtGetHeadId( 'H5') then
+      table.insert( PositionTableTC2, {Pos = "Pos22", TcPos = "T91", Head = "H5", Group = "G2"})
+   end
+   EgtJoinTables( PositionTable, PositionTableTC2)
+else
+   local SecSuppId = EgtGetTcPosId( 'T111')
+   if SecSuppId then
+      local bMortiser = EgtGetInfo( SecSuppId, 'Mortiser', 'b')
+      if bMortiser then
+         table.insert( PositionTable, {Pos = "Pos14", TcPos = "T111", Head = "H3", Group = "G2"})
+      else
+         table.insert( PositionTable, {Pos = "Pos14", TcPos = "T111", Head = "H1", Group = "G2"})
+      end
+   end
+   if EgtGetHeadId( 'H5') then
+      table.insert( PositionTable, {Pos = "Pos14", TcPos = "T91", Head = "H5", Group = "G2"})
    end
 end
-if EgtGetHeadId( 'H5') then
-   table.insert( PositionTable, {Pos = "Pos14", TcPos = "T91", Head = "H5", Group = "G2"})
-end
 
-local UsePositionHead = true
+local UsePositionHead = false
 
 local function IsInGeomSet( ToolHead, PosHead)
    for GsIndex = 1, #GS do

ToolNotes.ini

@@ -6,36 +6,38 @@
 
 [DRILL_STD]
 0=th,TH,
-1=d,STEP
-2=s,DOUBLE
+1=l,STEP
+2=tl,DOUBLE
 
 [SAW_STD]
 0=th,TH,
-1=d,STEP
-2=d,SIDESTEP
+1=l,STEP
+2=l,SIDESTEP
 3=b,LONGCUT
 
 [SAW_FLAT]
 0=th,TH,
-1=d,STEP
-2=d,SIDESTEP
+1=l,STEP
+2=l,SIDESTEP
 3=b,LONGCUT
 
 [MILL_STD]
 0=th,TH,
-1=d,STEP
-2=d,SIDESTEP
-3=d,SIDEDEPTH
-4=s,DOUBLE
+1=l,STEP
+2=l,SIDESTEP
+3=l,SIDEDEPTH
+4=tl,DOUBLE
+5=lr,TOOL_OVERHANG
 
 [MILL_NOTIP]
 0=th,TH,
-1=d,STEP
-2=d,SIDESTEP
-3=d,SIDEDEPTH
-4=s,DOUBLE
+1=l,STEP
+2=l,SIDESTEP
+3=l,SIDEDEPTH
+4=tl,DOUBLE
+5=lr,TOOL_OVERHANG
 
 [MORTISE_STD]
 0=b,MORTISE
-1=d,STEP
-2=d,SIDESTEP
+1=l,STEP
+2=l,SIDESTEP

UpdateLog.txt

@@ -1,13 +1,87 @@
            ==== Common_FAST Update Log ====
 
-Versione 2.7a3 (08/01/2024)
+Versione 3.1a2 (26/01/2026)
+- (GEN) Nella G101 il parametro EE era sempre a 4 perchè la variabile veniva settata dopo. Ticket#2796
+
+Versione 3.1a1 (08/01/2026)
+- (SIM) Ottimizzata scrittura funzione ClampCheck post aggiornamento dll
+- (SIM) Corretto problema della funzione OnSimulDispositionStart in caso di fase finale.
+- (MLDE-SIM-GEN) Variabile DeltaTol deve essere spostata in MLDE
+
+Versione 2.7l3 (22/12/2025)
+- (SIM) Eliminata MinJoin, utilizzata al suo posto funzione già esistente UpdateMinJoin nell'mlde
+- (SIM) Modificata formula calcolo Area minima
+
+Versione 2.7l2 (18/12/2025)
+- (SIM) Aggiunta funzione CheckClamping
+
+Versione 2.7l1 (10/12/2025)
+- (SIM) Aggiornata risoluzione VMillTol in funzione dello spessore lama
+- (EST) Modifiche a calcolo stima tempi, da verificare.
+- (SIM) Corretto movimento in simulazione che non rispettava movimento generato.
+- (GEN) Con controllo NUM/NUM_PLUS nella scrittura della coordinata tolto il simbolo '='
+- (SIM) Aggiunto controllo C in base a carico Dx o Sx durante il cambio utensile
+
+Versione 2.7k1 (10/11/2025)
+- (GEN) Corretto set variabili info utensile prima del movimento in home in caso di pezzi alti per NUM/NUM_PLUS.
+
+Versione 2.7j2 (08/10/2025)
+- (SIM-GEN) Quando si scarica motosega, si raddrizza prima l'asse B e poi si muove il C. Ora sempre e non solo se pezzo alto.
+
+Versione 2.7j1 (06/10/2025)
+- (SIM-GEN) Quando si scarica motosega, si raddrizza prima l'asse B e poi si muove il C.
+- (MLDE-SIM) Controllo collisione tra utensile e TOP testa C. Serve CAM5 2.7j1
+
+Versione 2.7i3 (23/09/2025)
+- (MLDE-ALL) Spostate costanti dimensioni utensili in MLDE.
+
+Versione 2.7i2 (17/09/2025)
+- (EST) Stima tempi considerando accelerazioni
+- (SIM) Prelievo e deposito motosega con gli angoli comunicati da Essetre
+
+Versione 2.7i1 (08/09/2025)
+- (SIM-GEN) Se lavorazione precedente e successiva con motosega e si cambiano assi rotanti, vado in parcheggio per ruotare. Ticket#1844
+- (SIM-GEN) Per NEWCLAMPING, corretto un caso di riposizionemento allo scarico dove la pinza V poteva andare in posizione direttamente, ma cercava di fare passo pellegrino. Ticket#2572
+
+Versione 2.7g1 (01/07/2025)
+- (GEN) Aggiunti parametri FMAXPINZE, MAXACC, MINACC configurabili da TS3. Ticket#2052
+
+Versione 2.7f3 (26/06/2025)
+- (SIM-GEN) Aggiunti 10mm di sicurezza in caso di primo pinzaggio per stare oltre tolleranza riqualifica laser di 50mm. Ticket#2504
+
+Versione 2.7f2 (19/06/2025)
+- (GEN) Se in separazione il pezzo è andato più lontano della posizione standard, viene riletta. Ticket#2498
+
+Versione 2.7f1 (18/06/2025)
+- (SIM-GEN) Se utensile più lungo di 350mm, si va in posizione sicurezza come per la motosega. Ticket#2438
+
+Versione 2.7e1 (26/05/2025)
+- (SIM) Aumentata dimensione massima per la quale si rimuove uno scarto dal VMILL. Ticket#1438
+- (SIM) In simulazione, corretto selezione utensile per punte lunghe. Ticket#2438
+
+Versione 2.7d1 (14/04/2025)
+- (GEN) Corretto movimento iniziale in caso di motosega, si controlla solo se non è il carico. Ticket#2385
+
+Versione 2.7c1 (26/03/2025)
+- (GEN) All'inizio del codice ISO si scrive nel commento anche il controllo numerico utilizzato per la generazione.
+- (GEN) Aggiunta commenti HEADER e FOOTER per comunicazione con linea o altre macchine, da parte di Essetre.
+- (GEN) In MyAdjustLinearAxes si utilizza TDIR per calcolarsi gli offset per compatibilità con lavorazioni a 5 assi.
+
+Versione 2.7b1 (20/02/2025)
+- (SIM-GEN) Aggiunta possibilità di settare HCING/TCING nelle note di ogni singola lavorazione per gestire parte non pinzabile del pezzo. Funziona solo con nuovo pinzaggio.
+- (SIM-GEN) Piccola correzione calcolo posizione carrelli con nuova strategia di pinzaggio.
+- (SIM-GEN) Caricamento libreria EmtGenMachining. Si fa una require con PCALL perchè la libreria è opzionale e non è detto che ci sia. In installazione CAM5 dalla 2.7a1
+- (GEN) Per controllo TPA, modifica al numero di decimali.
+- (SIM) Aggiunta gestione per ToolHolder flottante
+
+Versione 2.7a3 (08/01/2025)
 - (GEN) Dopo separazione, in NUM_PLUS, si srive EH1 solo se macro G101, perchè altrimenti non è prevista. Ticket#2239
 
-Versione 2.7a2 (08/01/2024)
+Versione 2.7a2 (08/01/2025)
 - (MLDE-SIM) Aggiunta gestione FACOLTATIVA 'EstimationRapidMultiplier' in MLDE per regolare il tempo stimato. Se non presente in MLDE, default 1.
 - (SIM) Aggiunta gestione qualità VMILL da impostazioni macchina
 
-Versione 2.7a1 (07/01/2024)
+Versione 2.7a1 (07/01/2025)
 - (MLDE-SIM-GEN) Nuovo aggregato 90° (H7) per fresa tipo BlockHaus. Ticket#2142
 - (SIM-GEN) Aumentati limiti massimi di pinzaggio minimo
 

Version.lua

@@ -3,7 +3,7 @@
 
 local InfoCommon_STD_PP = {
    NAME = 'Common_FAST',            -- nome script PP standard
-   VERSION = '2.7a3',                 -- versione script
+   VERSION = '3.1a2',                 -- versione script
    MIN_MACH_VER_PP_COMMON = '2.5k1'   -- versione minima kernel
 }