LapJoint, Sidemill - Q08=1 applica sidemill in tutte le tasche aperte (L e U aperte), se tasca chiusa svuotatura di fresa. Se non può fresare e applica sidemill restituisce warning perchè il finito viene danneggiato.

Q08=2 applica sidemill sempre e non restituisce warning.

LuaLibs/WProcessLapJoint.lua

@@ -1367,7 +1367,7 @@ local function MakeByMill( Proc, nFacet, nOthFac, nRawId, b3Raw, dSideDist)
    if not sMilling then
       local sErr = 'Error : Side not found in library'
       EgtOutLog( sErr)
-      return false, sErr, true
+      return false, sErr
    end
    -- recupero i dati dell'utensile
    local dMillDiam = 20
@@ -1390,13 +1390,13 @@ local function MakeByMill( Proc, nFacet, nOthFac, nRawId, b3Raw, dSideDist)
    if dMillDiam < dDiam or dMaxDepth < dElev then
       local sErr = 'Error : Side Elevation too big'
       EgtOutLog( sErr)
-      return false, sErr, true
+      return false, sErr
    end
    local dMillExtra = dMillTotLen - dMillLen
    if Proc.Box:getMin():getZ() - dMillExtra < b3Raw:getMin():getZ() - 10 * GEO.EPS_SMALL then
       local sErr = 'Error : Tool collide with table'
       EgtOutLog( sErr)
-      return false, sErr, true
+      return false, sErr
    end
    -- inserisco la lavorazione di contornatura
    local sName = 'Mill_' .. ( EgtGetName( Proc.Id) or tostring( Proc.Id))
@@ -1453,7 +1453,7 @@ local function MakeByMill( Proc, nFacet, nOthFac, nRawId, b3Raw, dSideDist)
    if not EgtApplyMachining( true, false) then
       local _, sErr = EgtGetLastMachMgrError()
       EgtSetOperationMode( nMchFId, false)
-      return false, sErr
+      return false, sErr, nMchFId
    end
    return true
 end
@@ -2296,6 +2296,13 @@ local function MakeSideGrooveByMill( Proc, nFacet, nRawId, b3Raw, sCustomMach, d
       EgtOutLog( sErr)
       return false, sErr
    end
+
+   local _, nUseMillOnSide = EvaluateQParam( Proc)
+   if nUseMillOnSide and nUseMillOnSide < 2 and ( Proc.Fct > 3 or ( Proc.Fct == 3 and not Proc.IsThrough)) then
+      sWarn = 'Warning in LapJoint : Sidemill damage finished part'
+      EgtOutLog( sWarn)
+   end
+
    return true, sWarn
 end
 
@@ -2797,8 +2804,11 @@ local function MakeTwoFaces( Proc, nRawId, b3Raw)
                bLikeAsMakeFirstGroove = false
                return MakeSideGrooveByMill( Proc, nFacetVert, nRawId, b3Raw, EgtIf( bEnableMillOnSide and dMaxDepthOnSide, sMillOnSide, nil), dMaxDepthOnSide, bMakeFirstGroove, bMachFromDn, dAng, bLikeAsMakeFirstGroove, nil, nil, bDoubleMillOnSide)
             else
-               local bOk, sErr, bSideMachiningNotFound = MakeByMill( Proc, nFacet, 1 - nFacet, nRawId, b3Raw, dSideDist)
-               if not bOk and bSideMachiningNotFound then
+               local bOk, sErr, nInvalidMachId = MakeByMill( Proc, nFacet, 1 - nFacet, nRawId, b3Raw, dSideDist)
+               if not bOk then
+                  if nInvalidMachId then
+                     EgtRemoveOperation( nInvalidMachId)
+                  end
                   bOk, sErr = MakeByPocketing( Proc, nFacet, nRawId, b3Raw)
                end
                -- se angolo ottuso riprendo il lato quasi verticale
@@ -2881,7 +2891,7 @@ local function MakeMoreFaces( Proc, nRawId, b3Raw)
       local nFacInd, dElev, nFacInd2, dElev2 = WL.GetFaceWithMostAdj( Proc.Id, Proc.PartId)
       -- se necessario scambio le facce
       local bIsGroove3Blind = Proc.Fct == 3 and Proc.Topology == 'Groove' and not Proc.IsThrough
-      local bPreferSidemill = ( nUseMillOnSide >= 1)
+      local bPreferSidemill = ( nUseMillOnSide > 1)
       if Proc.Stype == 2 or ( bPreferSidemill and bIsGroove3Blind) then
          nFacInd, dElev, nFacInd2, dElev2 = nFacInd2, dElev2, nFacInd, dElev
       end