NON completamente funzionante - Ingressi e uscite Saw per Slot. Ticket#3045

LuaLibs/FacesBySaw.lua

@@ -931,7 +931,7 @@ function FacesBySaw.MakeTwo( Proc, nPhase, nRawId, nPartId, dOvmHead, sCutType,
 end
 
 ---------------------------------------------------------------------
-function FacesBySaw.CalcLeadInOutPerpGeom( ptP1, ptP2, vtV1, vtV2, vtN, dRad, vtRef, dCutExtra, b3Box)
+function FacesBySaw.CalcLeadInOutPerpGeom( ptP1, ptP2, vtV1, vtV2, vtN, dRad, vtRef, dCutExtra, b3Box, bIsRightWorkside)
    -- Mi assicuro che i vettori ingresso/uscita giacciano nel piano
    vtV1 = vtV1 - vtV1 * vtN * vtN ;   vtV1:normalize()
    vtV2 = vtV2 - vtV2 * vtN * vtN ;   vtV2:normalize()
@@ -941,7 +941,7 @@ function FacesBySaw.CalcLeadInOutPerpGeom( ptP1, ptP2, vtV1, vtV2, vtN, dRad, vt
    -- Sistema di riferimento intrinseco al taglio
    local vtX = vtTg ^ vtN
    local frFace = Frame3d( ptP1, vtX, vtTg, vtN)
-   local bRight = ( vtX * vtRef > 0)
+   local bRight = EgtIf( bIsRightWorkside == nil, ( vtX * vtRef > 0), bIsRightWorkside)
    EgtOutLog( 'LioPerp --> Vref=' .. tostring( vtRef) .. ' V1=' .. tostring( vtV1) .. ' V2=' .. tostring( vtV2), 3)
 
    -- Versore di attacco e uscita

LuaLibs/ProcessLapJoint.lua

@@ -5662,7 +5662,7 @@ function SawPlusChain.GetLongFaceEdges( Proc, Face)
 end
 
 
-function SawPlusChain.CalculateLeadInOut( Machining, EdgeToMachine, FaceToMachine, b3Raw)
+function SawPlusChain.CalculateLeadInOut( Machining, EdgeToMachine, FaceToMachine, b3Raw, Proc)
    -- TODO implementare le funzioni di Tool Collision Avoidance (vedi wiki e FacesBysaw -> CalcLeadInOutPerpGeom)
 
    -- si determina l'eventuale riduzione da applicare in caso di inizio o fine chiusi
@@ -5720,30 +5720,42 @@ function SawPlusChain.CalculateLeadInOut( Machining, EdgeToMachine, FaceToMachin
       else
          vtOrthO = -Vector3d( EdgeToMachine.ToolDirection)
       end
-      local ptP1 = Point3d( FaceToMachine.Edges.BottomEdge.ptStart)
-      local ptP2 = Point3d( FaceToMachine.Edges.BottomEdge.ptEnd)
-      local vtV1 = -Vector3d( FaceToMachine.Edges.SideEdges.StartEdge.vtEdge)
-      local vtV2 = Vector3d( FaceToMachine.Edges.SideEdges.EndEdge.vtEdge)
-      
+      local ptP1 = Point3d( EdgeToMachine.ptStart)
+      local ptP2 = Point3d( EdgeToMachine.ptEnd)
+      local Edges = BL.GetEdgesInfo( Proc, FaceToMachine.Id)
+      local vtV1 = -Vector3d( Edges[EdgeToMachine.PreviousEdgeIndex].vtEdge)
+      local vtV2 = Vector3d( Edges[EdgeToMachine.NextEdgeIndex].vtEdge)
+   
       local bInvert = Machining.Invert
       if bInvert then
          ptP1, ptP2 = ptP2, ptP1
          vtV1, vtV2 = vtV2, vtV1
       end
       local vtTg = ptP2 - ptP1 ;   vtTg:normalize()
-      Machining.vtTg = vtTg
-      Machining.vtV = vtV1
       
       -- Versore di riferimento
       local vtRef = Vector3d( vtTg)
       vtRef:rotate( vtN, EgtIf( bInvert, -90, 90))
       
+      local bIsRightWorkside = Machining.Workside == MCH_MILL_WS.RIGHT
+      if bIsRightWorkside ~= bInvert--[[ and EdgeToMachine.Id ~= FaceToMachine.Edges.BottomEdge.Id]] then
+         vtV1 = -vtV1
+         vtV2 = -vtV2
+      end
+
       local b3Box = BBox3d( b3Raw)
       b3Box:expand( BD.CUT_SIC)
       local ptPa1 = ptP1 + LeadIn.StartAddLength * -vtTg
       local ptPa2 = ptP2 + LeadOut.EndAddLength * vtTg
 
-      LeadIn.TangentDistance, LeadIn.PerpDistance, LeadOut.TangentDistance, LeadOut.PerpDistance = Fbs.CalcLeadInOutPerpGeom(  ptPa1, ptPa2, vtV1, vtV2, vtN, ( Machining.Tool.Diameter / 2), vtRef, -Machining.RadialOffset, b3Box)
+      Machining.vtTg = vtTg
+      LeadIn.vtV1 = vtV1
+      LeadOut.vtV2 = vtV2
+      LeadIn.ptP1 = ptP1
+      LeadOut.ptP2 = ptP2
+      Machining.vtOffset = vtRef
+
+      LeadIn.TangentDistance, LeadIn.PerpDistance, LeadOut.TangentDistance, LeadOut.PerpDistance = Fbs.CalcLeadInOutPerpGeom( ptPa1, ptPa2, vtV1, vtV2, vtN, ( Machining.Tool.Diameter / 2), vtRef, -Machining.RadialOffset, b3Box, bIsRightWorkside)
    else
       if Machining.IsStartClosed then
          LeadIn.StartAddLength = -dAddLengthToReduce
@@ -6002,7 +6014,7 @@ function SawPlusChain.Saw.CalculateMachiningParameters( Proc, FaceToMachine, Edg
    Cutting.BlockedAxis.VtN = FaceToMachine.VtN
    Cutting.BlockedAxis.VtOut = EgtIf( FaceToMachine.VtN:getX() > 0, X_AX(), -X_AX())
    -- approccio e retrazione
-   Cutting.LeadIn, Cutting.LeadOut = SawPlusChain.CalculateLeadInOut( Cutting, EdgeToMachine, FaceToMachine, b3Raw)
+   Cutting.LeadIn, Cutting.LeadOut = SawPlusChain.CalculateLeadInOut( Cutting, EdgeToMachine, FaceToMachine, b3Raw, Proc)
    -- eventuale step orizzontale
    Cutting.HorizontalSteps = {}
    if Cutting.Tool.SideStep then
@@ -6045,16 +6057,29 @@ function SawPlusChain.Saw.ApplyAllSteps( Cutting, b3Raw)
    local dOriginalLeadOutTangDistance = Cutting.LeadOut.TangentDistance
    
    for i = Cutting.HorizontalSteps.Count, 1, -1 do
-      Cutting.RadialOffset = dOriginalRadialOffset + Cutting.HorizontalSteps.StepLength * ( i - 1)
-      local dOrthoOffsetStep = ( Cutting.RadialOffset * ( Cutting.vtV * vtTg))
-      -- update distanza perpendicolare attacco per contemplare l'offset applicato
-      Cutting.LeadIn.PerpDistance = dOriginalLeadInPerpDistance - Cutting.RadialOffset
-      Cutting.LeadIn.TangentDistance = dOriginalLeadInTangDistance + dOrthoOffsetStep + Cutting.LeadIn.StartAddLength
-      Cutting.LeadOut.PerpDistance = dOriginalLeadOutPerpDistance - Cutting.RadialOffset
-      Cutting.LeadOut.TangentDistance = dOriginalLeadOutTangDistance - dOrthoOffsetStep - Cutting.LeadOut.EndAddLength
+      local dRadialStep = Cutting.HorizontalSteps.StepLength * ( i - 1)
+      local dDirectionProportion = ( Cutting.LeadIn.vtV1 * vtTg)
+      Cutting.RadialOffset = dOriginalRadialOffset + dRadialStep
+      local dStepOffset = Cutting.RadialOffset - dOriginalRadialOffset
+      local dTangOffsetStep = ( Cutting.RadialOffset * dDirectionProportion)
+      local bTiltedSlot = abs( dDirectionProportion) > 0 + 10 * GEO.EPS_SMALL
+      local bIsRightWorkside = Cutting.Workside == MCH_MILL_WS.RIGHT
 
-      Cutting.LeadIn.StartAddLength = Cutting.LeadIn.StartAddLength - dOrthoOffsetStep - Cutting.LeadIn.StartAddLength
-      Cutting.LeadOut.EndAddLength = Cutting.LeadOut.EndAddLength + dOrthoOffsetStep + Cutting.LeadOut.EndAddLength
+      -- update distanza perpendicolare attacco per contemplare l'offset applicato
+
+      local b3Box = BBox3d( b3Raw)
+      b3Box:expand( BD.CUT_SIC)
+      local ptPa1 = Cutting.LeadIn.ptP1 + ( Cutting.LeadIn.StartAddLength - dTangOffsetStep) * -vtTg + dStepOffset * Cutting.LeadIn.vtV1
+      local ptPa2 = Cutting.LeadOut.ptP2 + ( Cutting.LeadOut.EndAddLength + dTangOffsetStep) * vtTg + dStepOffset * Cutting.LeadOut.vtV2
+
+      Cutting.LeadIn.TangentDistance, Cutting.LeadIn.PerpDistance, Cutting.LeadOut.TangentDistance, Cutting.LeadOut.PerpDistance = Fbs.CalcLeadInOutPerpGeom( ptPa1, ptPa2, Cutting.LeadIn.vtV1, Cutting.LeadOut.vtV2, Cutting.BlockedAxis.VtN, ( Cutting.Tool.Diameter / 2), Cutting.vtOffset, -Cutting.RadialOffset, b3Box, bIsRightWorkside)
+      --Cutting.LeadIn.PerpDistance = dOriginalLeadInPerpDistance - dRadialStep --dOriginalLeadInPerpDistance - Cutting.RadialOffset
+      --Cutting.LeadIn.TangentDistance = dOriginalLeadInTangDistance + dTangOffsetStep --+ Cutting.LeadIn.StartAddLength
+      --Cutting.LeadOut.PerpDistance = dOriginalLeadOutPerpDistance - dRadialStep --- Cutting.RadialOffset
+      --Cutting.LeadOut.TangentDistance = dOriginalLeadOutTangDistance - dTangOffsetStep --- Cutting.LeadOut.EndAddLength
+
+      Cutting.LeadIn.StartAddLength = Cutting.LeadIn.StartAddLength + EgtIf( bTiltedSlot, - ( dTangOffsetStep + Cutting.LeadIn.StartAddLength), 0)
+      Cutting.LeadOut.EndAddLength = Cutting.LeadOut.EndAddLength + EgtIf( bTiltedSlot, ( dTangOffsetStep + Cutting.LeadOut.EndAddLength), 0)
       -- applicazione lavorazione
       bIsCuttingOk, sCuttingApplyMessage = SawPlusChain.ApplyMachining( Cutting, b3Raw)
       -- update messaggi

UpdateLog.txt

@@ -1,5 +1,9 @@
            ==== Beam Update Log ====
 
+Versione 3.1g2 (17/07/2026)
+- Modif : Diminuito LastStep forature in doppio
+- Modif : ScarfJoint tra le feature da eseguire dopo i fori che la attraversano
+
 Versione 3.1g1 (14/07/2026)
 - Modif : in slot con lama migliorati attacchi inclinati
 - Modif : in CleanCorner migliorie

Version.lua

@@ -2,5 +2,5 @@
 -- Gestione della versione di Beam
 
 NAME = 'Beam'
-VERSION = '3.1g1'
+VERSION = '3.1g2'
 MIN_EXE = '3.1b1'