Merge branch 'release/2.6h1'

- in split e headcut i tagli addizionali orizzontali o verticali, se la macchina ha i ruli, si fanno sempre con attacco tangenziale

BatchProcess.lua

@@ -461,7 +461,7 @@ else
    -- Passo in modalità lavora
    EgtSetCurrMachGroup( EgtGetLastMachGroup())
    -- Se necessario eseguo aggiornamento con setup corrente e ricalcolo delle lavorazioni
-   if bToRecalc then
+   if bToRecalc or BEAM.FLAG == 3 or BEAM.FLAG == 4 then
       EgtOutLog( ' +++ Recalculating all dispositions and machinings >>>')
       EgtImportSetup()
       EgtApplyAllMachinings()

BatchProcessNew.lua

@@ -562,7 +562,7 @@ else
    -- Passo in modalità lavora
    EgtSetCurrMachGroup( EgtGetLastMachGroup())
    -- Se necessario eseguo aggiornamento con setup corrente e ricalcolo delle lavorazioni
-   if bToRecalc then
+   if bToRecalc or BEAM.FLAG == 3 or BEAM.FLAG == 4 then
       EgtOutLog( ' +++ Recalculating all dispositions and machinings >>>')
       EgtImportSetup()
       EgtApplyAllMachinings()
@@ -626,7 +626,8 @@ if  ( BEAM.FLAG == 0 and ( bToProcess or bToRecalc)) or BEAM.FLAG == 3 or BEAM.F
 end
 
 -- *** Genero programma CN *** ( se richiesto)
-if BEAM.FLAG == 0 or BEAM.FLAG == 4 then
+local bIsGenerationEnabled = ( EgtGetNumberFromIni( 'Mach', 'NoPartProgram', 0, EgtGetIniFile()) == 0)
+if bIsGenerationEnabled and ( BEAM.FLAG == 0 or BEAM.FLAG == 4) then
    EgtOutLog( ' +++ Generating NC part program >>>')
    local sInfo = 'EgtCAM5' .. EgtIf( EgtIs64bit(), ' 64bit', '')
    if EgtGetExeVersion then

LuaLibs/FacesBySaw.lua

@@ -45,7 +45,7 @@ local BD = require( 'BeamData')
 local ML = require( 'MachiningLib')
 
 ---------------------------------------------------------------------
-function MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, nFaceUse, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert)
+function MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, nFaceUse, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, bForceTangentLeadInOut)
    EgtOutLog( 'FacesBySaw.MakeParallelOne', 3)
    -- dati della faccia
    local ptC, vtN = EgtSurfTmFacetCenter( nSurfId, nFacet, GDB_ID.ROOT)
@@ -76,7 +76,7 @@ function MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, nFaceUse, dVzLimD
    local bLioTang
    local Ktp = 1.1
    if BD.KIOTP then Ktp = BD.KIOTP end
-   if Ktp * dLi2Tang < dLiPerp then
+   if bForceTangentLeadInOut or ( Ktp * dLi2Tang < dLiPerp) then
       bLioTang = true
       dLiTang, dLiPerp, dLoTang, dLoPerp = dLi2Tang, dLi2Perp, dLo2Tang, dLo2Perp
       if BD.TURN then
@@ -192,7 +192,7 @@ local function GetNameSolidFaceIncludingLine( b3Solid, ptP1Comp, ptP2Comp)
 end
 
 ---------------------------------------------------------------------
-function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, bMaximizeVerticalDepth)
+function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, bMaximizeVerticalDepth, bSpecialTangentLeadInOut, bForceTangentLeadInOut)
    -- se lama con asse parallelo alla faccia, passo alla apposita funzione
    if ( Par5 == MCH_MILL_FU.PARAL_DOWN or
         Par5 == MCH_MILL_FU.PARAL_TOP or
@@ -200,7 +200,7 @@ function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDw
         Par5 == MCH_MILL_FU.PARAL_BACK or
         Par5 == MCH_MILL_FU.PARAL_LEFT or
         Par5 == MCH_MILL_FU.PARAL_RIGHT) then
-      return MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert)
+      return MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, bForceTangentLeadInOut)
    end
    -- la lama ha asse perpendicolare alla faccia
    EgtOutLog( 'FacesBySaw.MakeOne', 3)
@@ -330,8 +330,26 @@ function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDw
    local dLiTang, dLiPerp, dLoTang, dLoPerp, vtLio = FacesBySaw.CalcLeadInOutPerpGeom( ptPa1, ptPa2, vtV1, vtV2, vtN, dSawDiam / 2, vtRef, dCutExtra, b3Box)
    local dLenLi = sqrt( dLiTang * dLiTang + dLiPerp * dLiPerp)
    local dLenLo = sqrt( dLoTang * dLoTang + dLoPerp * dLoPerp)
+   local dLiCompLength = 0
    -- attacco tangente
-   local dLi2Tang, dLi2Perp, dLo2Tang, dLo2Perp = FacesBySaw.CalcLeadInOutTangGeom( ptPa1, ptPa2, vtN, dSawDiam / 2, vtRef, dCutExtra, b3Box)
+   local dLi2Tang = 0
+   local dLi2Perp = 0
+   local dLo2Tang = 0
+   local dLo2Perp = 0
+   local dLi2CompLength = 0
+
+   -- si predilige un attacco tangenziale (con calcolo automatico di quanto uscire) se faccia non troppo orientata verso X e linea non troppo inclinata in X
+   -- non si fa se macchina tipo PF e pezzo alto perchè la lama, uscendo da sopra, toccherebbe la traversa
+   -- TODO si potranno togliere i limiti sulle normali quando si implementerà un modo per calcolare Lead In / Out correttamente in tutti i casi
+   -- 
+   if bSpecialTangentLeadInOut and not bIsBiLinea and ( abs( vtN:getX()) < 0.5) and ( abs( vtTg:getX()) < 0.1736) and ( abs( vtN:getY()) < 0.5 or ( BD.MAX_DIM_HTCUT_HBEAM > 0 or ( b3Raw:getDimZ() < 420))) then
+      dLi2Tang = 0
+      dLi2Perp = BD.MAX_DIM_DICE + BD.CUT_EXTRA
+      dLi2CompLength = dLen + dSawDiam / 2 + BD.COLL_SIC
+      dLo2Tang = dSawDiam / 2
+   else
+      dLi2Tang, dLi2Perp, dLo2Tang, dLo2Perp = FacesBySaw.CalcLeadInOutTangGeom( ptPa1, ptPa2, vtN, dSawDiam / 2, vtRef, dCutExtra, b3Box)
+   end
    local dLenLi2 = abs( dLi2Tang)
    local dLenLo2 = abs( dLo2Tang)
 
@@ -402,7 +420,7 @@ function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDw
          dLoPerp = BD.COLL_SIC
       else
          bLioTang = true
-         dLiTang, dLiPerp, dLoTang, dLoPerp = dLi2Tang, dLi2Perp, dLo2Tang, dLo2Perp
+         dLiTang, dLiPerp, dLoTang, dLoPerp, dLiCompLength = dLi2Tang, dLi2Perp, dLo2Tang, dLo2Perp, dLi2CompLength
       end
    end
    -- posizione braccio
@@ -475,6 +493,7 @@ function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDw
    if BD.TURN and bLioTang == 1 then EgtSetMachiningParam( MCH_MP.LEADINTYPE, MCH_MILL_LI.TG_PERP) end
    EgtSetMachiningParam( MCH_MP.LITANG, dLiTang)
    EgtSetMachiningParam( MCH_MP.LIPERP, dLiPerp)
+   EgtSetMachiningParam( MCH_MP.LICOMPLEN, dLiCompLength)
    if BD.TURN and bLioTang == 2 then EgtSetMachiningParam( MCH_MP.LEADOUTTYPE, MCH_MILL_LO.PERP_TG) end
    EgtSetMachiningParam( MCH_MP.LOTANG, dLoTang)
    EgtSetMachiningParam( MCH_MP.LOPERP, dLoPerp)
@@ -624,7 +643,8 @@ function FacesBySaw.MakeTwo( Proc, nPhase, nRawId, nPartId, dOvmHead, sCutType,
             local vtOrthO = EgtIf( ( i % 2) == 1, vtRef[nOtInd], vtRef[nUpInd])
             -- lavoro la faccia
             for j = 1, #vCuts[i] do
-               local bOk, sErr = FacesBySaw.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthO, dNzLimDwnUp, dCutExtra, BD.CUT_SIC, 0, 0, 0, nil, b3Raw)
+               local bSpecialTangentLeadInOut = ( i % 2 == 0) and ( Proc.AffectedFaces.Left or Proc.AffectedFaces.Right)
+               local bOk, sErr = FacesBySaw.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthO, dNzLimDwnUp, dCutExtra, BD.CUT_SIC, 0, 0, 0, nil, b3Raw, nil, nil, bSpecialTangentLeadInOut)
                if not bOk then
                   return bOk, sErr
                end
@@ -684,14 +704,16 @@ function FacesBySaw.MakeTwo( Proc, nPhase, nRawId, nPartId, dOvmHead, sCutType,
                end
                -- taglio perpendicolare (limite Vz Down Up messo a -2 per non farlo mai intervenire)
                if vCuts[i][j] then
-                  local bOk, sErr = FacesBySaw.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthoO_1, -2, dExtraCut_1, BD.CUT_SIC, 0, 0, 0, nil, b3Raw)
+                  local bSpecialTangentLeadInOut = ( i % 2 == 0) and ( Proc.AffectedFaces.Left or Proc.AffectedFaces.Right)
+                  local bOk, sErr = FacesBySaw.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthoO_1, -2, dExtraCut_1, BD.CUT_SIC, 0, 0, 0, nil, b3Raw, nil, nil, bSpecialTangentLeadInOut)
                   if not bOk then
                      return bOk, sErr
                   end
                end
                -- taglio parallelo (limite Vz Down Up messo a -2 per non farlo mai intervenire)
                if vCuts[i+1][j] then
-                  local bOk, sErr = FacesBySaw.MakeOne( vCuts[i+1][j], 0, sCutting, dSawDiam, vtOrthoO_2, -2, dExtraCut_2, BD.CUT_SIC, 0, 0, 0, nil, b3Raw)
+                  local bSpecialTangentLeadInOut = ( ( i + 1) % 2 == 0) and ( Proc.AffectedFaces.Left or Proc.AffectedFaces.Right)
+                  local bOk, sErr = FacesBySaw.MakeOne( vCuts[i+1][j], 0, sCutting, dSawDiam, vtOrthoO_2, -2, dExtraCut_2, BD.CUT_SIC, 0, 0, 0, nil, b3Raw, nil, nil, bSpecialTangentLeadInOut)
                   if not bOk then
                      return bOk, sErr
                   end

LuaLibs/ProcessBlockHausFront.lua

@@ -151,7 +151,8 @@ function ProcessBlockHausFront.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, dO
       -- se va fatto, inserisco la lavorazione
       if bCut then
          local CutProc = { Id = AuxId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead)
          -- se taglio applicato setto la nota al gruppo Mach per non doverla lavorare una seconda volta
          if bOk then
@@ -242,7 +243,8 @@ function ProcessBlockHausFront.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, dO
          -- se va fatto, inserisco la lavorazione
          if bCut then
             local CutProc = { Id = AuxId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+            CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead)
             -- se taglio applicato setto la nota al gruppo Mach per non doverla lavorare una seconda volta
             if bOk then

LuaLibs/ProcessCut.lua

@@ -548,7 +548,8 @@ local function MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, b
                            dVzLimDwnUp = -0.708
                         end
                      end
-                     local bOk, sErr = Fbs.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtNewOrthoO, dVzLimDwnUp, BD.CUT_EXTRA, BD.CUT_SIC, 0, 0, 0, nil, b3Raw)
+                     local bSpecialTangentLeadInOut = ( i % 2 == 0) and ( Proc.AffectedFaces.Left or Proc.AffectedFaces.Right)
+                     local bOk, sErr = Fbs.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtNewOrthoO, dVzLimDwnUp, BD.CUT_EXTRA, BD.CUT_SIC, 0, 0, 0, nil, b3Raw, nil, nil, bSpecialTangentLeadInOut)
                      if not bOk then return bOk, sErr end
                   end
                   -- tutti gli altri casi vengono saltati
@@ -575,7 +576,8 @@ local function MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, b
                   elseif not BD.C_SIMM and not BD.TURN and vtN:getZ() > 0.707 then
                      dVzLimDwnUp = -0.708
                   end
-                  local bOk, sErr = Fbs.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthoO, dVzLimDwnUp, dExtraCut, BD.CUT_SIC, 0, 0, 0, sNotes, b3Raw)
+                  local bSpecialTangentLeadInOut = ( i % 2 == 0) and ( Proc.AffectedFaces.Left or Proc.AffectedFaces.Right)
+                  local bOk, sErr = Fbs.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthoO, dVzLimDwnUp, dExtraCut, BD.CUT_SIC, 0, 0, 0, sNotes, b3Raw, nil, nil, bSpecialTangentLeadInOut)
                   if not bOk then return bOk, sErr end
                end
             end
@@ -757,14 +759,16 @@ local function MakeFromDown( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead)
             end
             -- taglio perpendicolare (limite Vz Down Up messo a -2 per non farlo mai intervenire)
             if vCuts[i][j] then
-               local bOk, sErr = Fbs.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthoO_1, -2, dExtraCut_1, BD.CUT_SIC, 0, 0, 0, nil, b3Raw)
+               local bSpecialTangentLeadInOut = ( i % 2 == 0) and ( Proc.AffectedFaces.Left or Proc.AffectedFaces.Right)
+               local bOk, sErr = Fbs.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthoO_1, -2, dExtraCut_1, BD.CUT_SIC, 0, 0, 0, nil, b3Raw, nil, nil, bSpecialTangentLeadInOut)
                if not bOk then
                   return bOk, sErr
                end
             end
             -- taglio parallelo (limite Vz Down Up messo a -2 per non farlo mai intervenire)
             if vCuts[i+1][j] then
-               local bOk, sErr = Fbs.MakeOne( vCuts[i+1][j], 0, sCutting, dSawDiam, vtOrthoO_2, -2, dExtraCut_2, BD.CUT_SIC, 0, 0, 0, nil, b3Raw)
+               local bSpecialTangentLeadInOut = ( i % 2 == 0) and ( Proc.AffectedFaces.Left or Proc.AffectedFaces.Right)
+               local bOk, sErr = Fbs.MakeOne( vCuts[i+1][j], 0, sCutting, dSawDiam, vtOrthoO_2, -2, dExtraCut_2, BD.CUT_SIC, 0, 0, 0, nil, b3Raw, nil, nil, bSpecialTangentLeadInOut)
                if not bOk then return bOk, sErr end
             end
          end

LuaLibs/ProcessDoubleCut.lua

@@ -521,7 +521,8 @@ function ProcessDoubleCut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
          local b3Add = EgtGetBBoxGlob( AddId, GDB_BB.STANDARD)
          -- applico lavorazione
          local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = b3Add, Fct = 1, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead, nil, nil, bForced, b3Raw, sNotes, dOvmTail, true)
          if not bOk then return bOk, sErr end
       end
@@ -533,7 +534,8 @@ function ProcessDoubleCut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
          local b3Add = EgtGetBBoxGlob( AddId, GDB_BB.STANDARD)
          -- applico lavorazione
          local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = b3Add, Fct = 1, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead, nil, nil, bForced, b3Raw, sNotes, dOvmTail, true)
          if not bOk then return bOk, sErr end
       end

LuaLibs/ProcessDovetail.lua

@@ -1433,7 +1433,8 @@ local function MakeAuxCut( Proc, nPhase, nRawId, nPartId, dOvmHead, b3Raw, b3Sol
       return true
    end
    -- inserisco la lavorazione
-   local CutProc = { Id = AuxId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg, Head = Proc.Head, Tail = Proc.Tail}
+   local CutProc = { Id = AuxId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg, Head = Proc.Head, Tail = Proc.Tail, PartId = Proc.PartId}
+   CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
    local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead)
    if not bOk then return bOk, sErr end
    -- imposto la nota nel gruppo aggiuntivo di lavorazione per evitare di tagliare una seconda volta

LuaLibs/ProcessDtMortise.lua

@@ -210,7 +210,8 @@ function ProcessDtMortise.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          local AddId = EgtSurfTmPlaneInBBox( nAddGrpId, ptCutC, vtCutN, b3Solid, GDB_RT.GLOB)
          local b3Cut = EgtGetBBoxGlob( AddId or GDB_ID.NULL, GDB_BB.STANDARD)
          local CutProc = { Id = AddId, Grp = Proc.Grp - 2, Prc = 10, Box = b3Cut, Fct = 1, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          local bFromBottom = ( b3Solid:getDimX() < BD.LEN_SHORT_PART and vtExtr:getZ() > 0.25)
          local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dCurrOvmH, bFromBottom)
          if not bOk then return bOk, sErr end

LuaLibs/ProcessDtTenon.lua

@@ -207,7 +207,8 @@ function ProcessDtTenon.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
          -- altrimenti applico taglio di lama
          else
             local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+            CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
             local bFromBottom = ( b3Solid:getDimX() < BD.LEN_SHORT_PART and vtExtr:getZ() > 0.25)
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead, bFromBottom)
             if not bOk then return bOk, sErr end

LuaLibs/ProcessHeadCut.lua

@@ -173,7 +173,8 @@ local function AddVerticalPreCuts( Proc, sCutting, dCutXOffset, b3Raw )
    for j = nVerticalCuts, 1, -1 do
       local nFaceUse = MCH_MILL_FU.PARAL_FRONT
       local dVerticalCutOffset = dVerticalSliceHeight * -j
-      bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dVerticalCutOffset, 0, 0, '', b3Raw)
+      local bForceTangentLeadInOut = BD.PRESS_ROLLER
+      bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dVerticalCutOffset, 0, 0, '', b3Raw, nil, nil, nil, bForceTangentLeadInOut)
       if not bOk then return bOk, sErr end
    end
    return bOk, sErr
@@ -359,7 +360,8 @@ function ProcessHeadCut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, bNeedHCut
             for j = nHorizontalCuts, 1, -1 do
                local nFaceUse = MCH_MILL_FU.PARAL_DOWN
                local dHorizontalCutOffset = dHorizontalSliceHeight * -j
-               local bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dHorizontalCutOffset, 0, 0, '', b3Raw)
+               local bForceTangentLeadInOut = BD.PRESS_ROLLER
+               local bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dHorizontalCutOffset, 0, 0, '', b3Raw, nil, nil, nil, bForceTangentLeadInOut)
                if not bOk then return bOk, sErr end
             end
             -- se necessario taglio verticale doppio, eseguo l'opposto

LuaLibs/ProcessLapJoint.lua

@@ -1191,7 +1191,8 @@ local function MakePreCuts( Proc, nPhase, nRawId, nPartId, dOvmHead, b3Raw, nCha
          EgtSetName( AddId, 'AddCut_' .. tostring( Proc.Id))
          -- applico lavorazione
          local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          local nCutFacet = EgtSurfTmFacetCount( AddId)
          if nCutFacet == 1 then
             return Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead)
@@ -2551,7 +2552,7 @@ end
 ---------------------------------------------------------------------
 local function MakeChamfer( Proc, bIs3Faces, nAddGrpId, vtOrtho, b3Solid, nSurfInt, dDepthCham)
 
-   -- Se variabile globale indica che lo smusso è gi stato fatto, esco
+   -- Se variabile globale indica che lo smusso è già stato fatto, esco
    if bMadeChamfer then
       return 0
    end
@@ -2565,6 +2566,7 @@ local function MakeChamfer( Proc, bIs3Faces, nAddGrpId, vtOrtho, b3Solid, nSurfI
    end
    -- ottengo le curve di contorno libero
    local nAuxId1, nAuxId2, nNumIdAux
+   local bIsOpenPath = false
    if bIs3Faces then
       -- estraggo i percorsi
       nAuxId1, nNumIdAux = EgtExtractSurfTmLoops( Proc.Id, nAddGrpId)
@@ -2575,6 +2577,36 @@ local function MakeChamfer( Proc, bIs3Faces, nAddGrpId, vtOrtho, b3Solid, nSurfI
    else
       nAuxId1, nNumIdAux = EgtExtractSurfTmLoops( Proc.Id, nAddGrpId)
       if not nNumIdAux then nNumIdAux = 0 end
+      -- se non è una curva chiusa bisogna estrarre le sole curve da lavorare
+      if Proc.TopologyLongName == 'Groove-Blind-RightAngles-Parallel-4' then
+         local IdsToMachine = {}
+         bIsOpenPath = true
+         local nFirstId, nIdCount = EgtExplodeCurveCompo( nAuxId1)
+         for i = nFirstId, nFirstId + nIdCount - 1, 1 do
+            -- se segmento di retta
+            if EgtGetType( i) == GDB_TY.CRV_LINE then
+               local _, nEntitiesCount = EgtCurveDomain(i)
+               for j = 0, nEntitiesCount - 1 do
+                  local ptStart = EgtUP( i, j, GDB_RT.GLOB)
+                  local ptEnd = EgtUP( i, j + 1, GDB_RT.GLOB)
+                  if ( AreSameVectorApprox( vtOrtho, X_AX()) and ( abs( ptStart:getX() - b3Solid:getMax():getX()) < 100 * GEO.EPS_SMALL and abs( ptEnd:getX() - b3Solid:getMax():getX()) < 100 * GEO.EPS_SMALL) or
+                       AreSameVectorApprox( vtOrtho, -X_AX()) and ( abs( ptStart:getX() - b3Solid:getMin():getX()) < 100 * GEO.EPS_SMALL and abs( ptEnd:getX() - b3Solid:getMin():getX()) < 100 * GEO.EPS_SMALL) or
+                       AreSameVectorApprox( vtOrtho, Y_AX()) and ( abs( ptStart:getY() - b3Solid:getMax():getY()) < 100 * GEO.EPS_SMALL and abs( ptEnd:getY() - b3Solid:getMax():getY()) < 100 * GEO.EPS_SMALL) or
+                       AreSameVectorApprox( vtOrtho, -Y_AX()) and ( abs( ptStart:getY() - b3Solid:getMin():getY()) < 100 * GEO.EPS_SMALL and abs( ptEnd:getY() - b3Solid:getMin():getY()) < 100 * GEO.EPS_SMALL) or
+                       AreSameVectorApprox( vtOrtho, Z_AX()) and ( abs( ptStart:getZ() - b3Solid:getMax():getZ()) < 100 * GEO.EPS_SMALL and abs( ptEnd:getZ() - b3Solid:getMax():getZ()) < 100 * GEO.EPS_SMALL) or
+                       AreSameVectorApprox( vtOrtho, -Z_AX()) and ( abs( ptStart:getZ() - b3Solid:getMin():getZ()) < 100 * GEO.EPS_SMALL and abs( ptEnd:getZ() - b3Solid:getMin():getZ()) < 100 * GEO.EPS_SMALL)
+                     ) then
+                     table.insert( IdsToMachine, i)
+                  end
+               end
+            else
+               return 0
+            end
+         end
+         local ptNear = EgtSurfTmFacetCenter(Proc.Id, 0, GDB_ID.ROOT)
+         nAuxId1 = EgtCurveCompoByReorder( nAddGrpId, IdsToMachine, ptNear, true, GDB_ID.ROOT)
+         nNumIdAux = 1
+      end
    end
 
    local dExtra = 2
@@ -2594,13 +2626,20 @@ local function MakeChamfer( Proc, bIs3Faces, nAddGrpId, vtOrtho, b3Solid, nSurfI
          end
       else
          AuxId = nAuxId1 + i - 1
-         vtExtr, _, _ = EgtCurveArea( AuxId)
-      end
-      if vtExtr then
-         if not bIs3Faces then
+         if bIsOpenPath then
+            _, vtExtr = EgtCurveIsFlat( AuxId)
+         else
+            vtExtr, _, _ = EgtCurveArea( AuxId)
+         end
+         if vtExtr then
             local fFrCurve = EgtGetGlobFrame( AuxId)
             vtExtr:toGlob( fFrCurve)
+            if bIsOpenPath and vtExtr * vtOrtho < GEO.EPS_SMALL then
+               vtExtr = -vtExtr
+            end
          end
+      end
+      if vtExtr then
 --         if bIs3Faces and i == nNumIdAux then
 --            vtExtr = -vtExtr
 --         end
@@ -2844,6 +2883,12 @@ local function MakeByChainOrSaw( Proc, nPhase, nRawId, nPartId, nFacInd,
          local nOk, sErr = MakeChamfer( Proc, bIs3Faces, nAddGrpId, vtOrtho, b3Solid, nSurfInt, dDepthCham)
          if nOk < 0 then return false, sErr end
       end
+   -- slot aperta su due lati
+   elseif Proc.TopologyLongName == 'Groove-Blind-RightAngles-Parallel-4' then
+      if nChamfer > 0 then
+         local nOk, sErr = MakeChamfer( Proc, false, nAddGrpId, rfFac:getVersZ(), b3Solid, nil, dDepthCham)
+         if nOk < 0 then return false, sErr end
+      end
    end
    if not dDepth then dDepth = dElev end
    -- Recupero le facce adiacenti alla principale
@@ -5110,22 +5155,29 @@ function SawPlusChain.ApplyMachining( Machining, b3Raw)
       local nErr
       nErr, sErr = EgtGetLastMachMgrError()
       -- se mortasatura e l'errore è compatibile (Axes values not calculable) si prova con l'altra configurazione dell'asse bloccato
-      -- TODO valutare se c'è modo di capire preventivamente la configurazione dell'asse bloccato e quindi rimuovere questa parte di codice
-      if Machining.Type == MCH_OY.MORTISING and nErr == 2507 then
-         if Machining.BlockedAxis.Orientation  == 'perpendicular' then
-            Machining.BlockedAxis.Orientation = 'parallel'
-         else
-            Machining.BlockedAxis.Orientation  = 'perpendicular'
+      if Machining.Type == MCH_OY.MORTISING then
+         -- se errore "Axes values not calculable" si prova con l'altra configurazione dell'asse bloccato
+         if nErr == 2507 then
+            if Machining.BlockedAxis.Orientation  == 'perpendicular' then
+               Machining.BlockedAxis.Orientation = 'parallel'
+            else
+               Machining.BlockedAxis.Orientation  = 'perpendicular'
+            end
+            EgtSetMachiningParam( MCH_MP.BLOCKEDAXIS, BL.GetBlockedAxis( Machining.Name, Machining.BlockedAxis.Orientation, b3Raw, Machining.BlockedAxis.VtN, Machining.BlockedAxis.VtOut))
+            if Machining.SuggestedAngles.Index == 1 then
+               Machining.SuggestedAngles.Index = 2
+            else
+               Machining.SuggestedAngles.Index = 1
+            end
+            EgtSetMachiningParam( MCH_MP.INITANGS, BL.GetChainSawInitAngs( Machining.SuggestedAngles.VtN, Machining.SuggestedAngles.VtOrtho, Machining.SuggestedAngles.Index))
+            sErr = ''
+            bIsApplyOk = ML.ApplyMachining( true, false)
+         -- se errore "Outstroke" e permesso ToolInvert provo ad invertire il lato di lavorazione
+         elseif Machining.AllowToolInvert and nErr == 2508 then
+            EgtSetMachiningParam( MCH_MP.TOOLINVERT, not Machining.ToolInvert)
+            sErr = ''
+            bIsApplyOk = ML.ApplyMachining( true, false)
          end
-         EgtSetMachiningParam( MCH_MP.BLOCKEDAXIS, BL.GetBlockedAxis( Machining.Name, Machining.BlockedAxis.Orientation, b3Raw, Machining.BlockedAxis.VtN, Machining.BlockedAxis.VtOut))
-         if Machining.SuggestedAngles.Index == 1 then
-            Machining.SuggestedAngles.Index = 2
-         else
-            Machining.SuggestedAngles.Index = 1
-         end
-         EgtSetMachiningParam( MCH_MP.INITANGS, BL.GetChainSawInitAngs( Machining.SuggestedAngles.VtN, Machining.SuggestedAngles.VtOrtho, Machining.SuggestedAngles.Index))
-         sErr = ''
-         bIsApplyOk = ML.ApplyMachining( true, false)
       end
       if not bIsApplyOk then
          nErr, sErr = EgtGetLastMachMgrError()
@@ -5182,18 +5234,16 @@ function SawPlusChain.Saw.CalculateMachiningParameters( Proc, FaceToMachine, Edg
       Cutting.Message = 'Feature '.. Proc.FeatureId .. ' : strategy ' .. SawPlusChain.Name .. ' not applicable - saw blade not found'
       Cutting.CanApply = false
       EgtOutLog( Cutting.Message)
-      return Cutting
    end
    Cutting.Type = MCH_OY.MILLING
    Cutting.Tool = SawPlusChain.GetToolFromMachining( Cutting.Name)
 
-   -- verifica dimensioni tasca compatibili
+   -- verifica dimensioni tasca e direzione compatibili
    -- se tasca meno spessa della lama la strategia non è applicabile
    if Cutting.Tool.Thickness > dPocketHeight + 10 * GEO.EPS_SMALL then
       Cutting.Message = 'Feature '.. Proc.FeatureId .. ' : strategy ' .. SawPlusChain.Name .. ' not applicable - pocket too narrow for saw blade thickness'
       Cutting.CanApply = false
       EgtOutLog( Cutting.Message)
-      return Cutting
    end
    if #( Proc.MainFaces.SideFaces) > 1 then
       -- se tasca più stretta della lama la strategia non è applicabile
@@ -5201,9 +5251,13 @@ function SawPlusChain.Saw.CalculateMachiningParameters( Proc, FaceToMachine, Edg
          Cutting.Message = 'Feature '.. Proc.FeatureId .. ' : strategy ' .. SawPlusChain.Name .. ' not applicable - pocket too narrow for saw blade diameter'
          Cutting.CanApply = false
          EgtOutLog( Cutting.Message)
-         return Cutting
       end
    end
+   if EdgeToMachine.ToolDirection:getZ() < BD.NZ_MINA then
+      Cutting.CanApply = false
+      Cutting.Message = 'Feature '.. Proc.FeatureId .. ' : skipped sawblade from bottom'
+      EgtOutLog( Cutting.Message)
+   end
 
    -- parametri della lavorazione
    -- inizio e fine aperti o chiusi
@@ -5334,6 +5388,7 @@ function SawPlusChain.Chainsaw.CalculateMachiningParameters( Proc, FaceToMachine
    Mortising.CanApply = true
    Mortising.Message = ''
    Mortising.ProcId = Proc.Id
+   Mortising.AllowToolInvert = false
    local bNeedToMachineOtherSide = false
    local dTestCornerRadius = 43
    -- OneSide | OneSideAndExtend | BothSides | BothSidesAndExtend
@@ -5377,18 +5432,21 @@ function SawPlusChain.Chainsaw.CalculateMachiningParameters( Proc, FaceToMachine
       Mortising.Message = 'Feature '.. Proc.FeatureId .. ' : strategy ' .. SawPlusChain.Name .. ' not applicable - chainsaw not found'
       Mortising.CanApply = false
       EgtOutLog( Mortising.Message)
-      return Mortising
    end
    Mortising.Type = MCH_OY.MORTISING
    Mortising.Tool = SawPlusChain.GetToolFromMachining( Mortising.Name)
 
+   -- in caso di tunnel da un lato permetto eventuale inversione lato di lavoro in caso di errori di applicazione (es: Outstroke)
+   if Proc.Topology == 'Tunnel' and sMortisingType == 'OneSide' or sMortisingType == 'OneSideAndExtend' then
+      Mortising.AllowToolInvert = true
+   end
+
    -- verifica dimensioni tasca compatibili
    -- se tasca meno spessa della sega a catena la strategia non è applicabile
    if Mortising.Tool.Thickness > dPocketHeight + 10 * GEO.EPS_SMALL then
       Mortising.Message = 'Feature '.. Proc.FeatureId .. ' : strategy ' .. SawPlusChain.Name .. ' not applicable - pocket too narrow for chainsaw thickness'
       Mortising.CanApply = false
       EgtOutLog( Mortising.Message)
-      return Mortising
    end
    if #( Proc.MainFaces.SideFaces) > 1 then
       -- se tasca più stretta della sega a catena la strategia non è applicabile
@@ -5396,9 +5454,13 @@ function SawPlusChain.Chainsaw.CalculateMachiningParameters( Proc, FaceToMachine
          Mortising.Message = 'Feature '.. Proc.FeatureId .. ' : strategy ' .. SawPlusChain.Name .. ' not applicable - pocket too narrow for chainsaw width'
          Mortising.CanApply = false
          EgtOutLog( Mortising.Message)
-         return Mortising
       end
    end
+   if EdgeToMachine.ToolDirection:getZ() < - 10 * GEO.EPS_ANG_SMALL then
+      Mortising.CanApply = false
+      Mortising.Message = 'Feature '.. Proc.FeatureId .. ' : skipped chainsaw from bottom'
+      EgtOutLog( Mortising.Message)
+   end
 
    -- parametri della lavorazione
    -- inizio e fine aperti o chiusi
@@ -5555,9 +5617,9 @@ function SawPlusChain.Make( bOnlySaw, Proc, nRawId)
    local bIsCuttingOk = false
    if Cutting.CanApply then
       bIsCuttingOk, Cutting.Message = SawPlusChain.Saw.ApplyAllSteps( Cutting, b3Raw)
-   end
-   if not bIsCuttingOk then
-      return bIsCuttingOk, Cutting.Message
+      if not bIsCuttingOk then
+         return bIsCuttingOk, Cutting.Message
+      end
    end
    local dBottomDepthToMachine = Cutting.RadialOffset
    -- lato opposto del tunnel
@@ -5566,9 +5628,9 @@ function SawPlusChain.Make( bOnlySaw, Proc, nRawId)
       bIsCuttingOk = false
       if Cutting.CanApply then
          bIsCuttingOk, Cutting.Message = SawPlusChain.Saw.ApplyAllSteps( Cutting, b3Raw)
-      end
-      if not bIsCuttingOk then
-         return bIsCuttingOk, Cutting.Message
+         if not bIsCuttingOk then
+            return bIsCuttingOk, Cutting.Message
+         end
       end
    else
       -- se la lama non è arrivata sul fondo e c'è almeno un lato aperto va lavorato
@@ -5579,9 +5641,9 @@ function SawPlusChain.Make( bOnlySaw, Proc, nRawId)
             bIsCuttingOk = false
             if Cutting.CanApply then
                bIsCuttingOk, Cutting.Message = SawPlusChain.Saw.ApplyAllSteps( Cutting, b3Raw)
-            end
-            if not bIsCuttingOk then
-               return bIsCuttingOk, Cutting.Message
+               if not bIsCuttingOk then
+                  return bIsCuttingOk, Cutting.Message
+               end
             end
          end
          -- eventuale lavorazione di lama - lato della tasca in cui finisce la lavorazione
@@ -5590,9 +5652,9 @@ function SawPlusChain.Make( bOnlySaw, Proc, nRawId)
             bIsCuttingOk = false
             if Cutting.CanApply then
                bIsCuttingOk, Cutting.Message = SawPlusChain.Saw.ApplyAllSteps( Cutting, b3Raw)
-            end
-            if not bIsCuttingOk then
-               return bIsCuttingOk, Cutting.Message
+               if not bIsCuttingOk then
+                  return bIsCuttingOk, Cutting.Message
+               end
             end
          end
       -- la lama è arrivata sul fondo e tasca passante, non servono ulteriori lavorazioni
@@ -5626,9 +5688,9 @@ function SawPlusChain.Make( bOnlySaw, Proc, nRawId)
       bIsMortisingOk = false
       if Mortising.CanApply then
          bIsMortisingOk, Mortising.Message = SawPlusChain.Chainsaw.ApplyAllSteps( Mortising, b3Raw)
-      end
-      if not bIsMortisingOk then
-         return bIsMortisingOk, Mortising.Message
+         if not bIsMortisingOk then
+            return bIsMortisingOk, Mortising.Message
+         end
       end
    else
       -- se la sega a catena non è arrivata sul fondo e c'è almeno un lato aperto va lavorato
@@ -5639,9 +5701,9 @@ function SawPlusChain.Make( bOnlySaw, Proc, nRawId)
             bIsMortisingOk = false
             if Mortising.CanApply then
                bIsMortisingOk, Mortising.Message = SawPlusChain.Chainsaw.ApplyAllSteps( Mortising, b3Raw)
-            end
-            if not bIsMortisingOk then
-               return bIsMortisingOk, Mortising.Message
+               if not bIsMortisingOk then
+                  return bIsMortisingOk, Mortising.Message
+               end
             end
          end
          -- eventuale lavorazione di sega a catena - lato della tasca in cui finisce la lavorazione
@@ -5650,9 +5712,9 @@ function SawPlusChain.Make( bOnlySaw, Proc, nRawId)
             bIsMortisingOk = false
             if Mortising.CanApply then
                bIsMortisingOk, Mortising.Message = SawPlusChain.Chainsaw.ApplyAllSteps( Mortising, b3Raw)
-            end
-            if not bIsMortisingOk then
-               return bIsMortisingOk, Mortising.Message
+               if not bIsMortisingOk then
+                  return bIsMortisingOk, Mortising.Message
+               end
             end
          end
       end

LuaLibs/ProcessMortise.lua

@@ -417,7 +417,8 @@ function ProcessMortise.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          local AddId = EgtSurfTmPlaneInBBox( nAddGrpId, ptCutC, vtCutN, b3Solid, GDB_RT.GLOB)
          local b3Cut = EgtGetBBoxGlob( AddId or GDB_ID.NULL, GDB_BB.STANDARD)
          local CutProc = { Id = AddId, Grp = Proc.Grp - 2, Prc = 10, Box = b3Cut, Fct = 1, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          local bFromBottom = ( b3Solid:getDimX() < BD.LEN_SHORT_PART and vtExtr:getZ() > 0.25)
          local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dCurrOvmH, bFromBottom)
          if not bOk then return bOk, sErr end

LuaLibs/ProcessProfCamb.lua

@@ -307,7 +307,8 @@ function ProcessProfCamb.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          -- altrimenti applico taglio di lama
          else
             local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+            CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dCurrOvmH)
             if not bOk then
                return false, sErr

LuaLibs/ProcessProfConcave.lua

@@ -311,7 +311,8 @@ function ProcessProfConcave.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          -- altrimenti applico taglio di lama
          else
             local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+            CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dCurrOvmH)
             if not bOk then
                return false, sErr

LuaLibs/ProcessProfConvex.lua

@@ -311,7 +311,8 @@ function ProcessProfConvex.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          -- altrimenti applico taglio di lama
          else
             local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+            CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dCurrOvmH)
             if not bOk then
                return false, sErr

LuaLibs/ProcessProfFront.lua

@@ -258,7 +258,8 @@ function ProcessProfFront.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          -- altrimenti applico taglio di lama
          else
             local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+            CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dCurrOvmH)
             if not bOk then
                return false, sErr

LuaLibs/ProcessProfHead.lua

@@ -293,7 +293,8 @@ function ProcessProfHead.Make( Proc, nPhase, nRawId, nPartId, dCurrOvmH)
          -- altrimenti applico taglio di lama
          else
             local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+            CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dCurrOvmH)
             if not bOk then
                return false, sErr

LuaLibs/ProcessRidgeLap.lua

@@ -134,7 +134,8 @@ function ProcessRidgeLap.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
          -- applico taglio di lama
          local b3Cut = EgtGetBBoxGlob( AddId or GDB_ID.NULL, GDB_BB.STANDARD)
          local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = b3Cut, Fct = 1, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          if BL.IsCutNeeded( CutProc, b3Raw, dOvmHead) then
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead, false)
             if not bOk then return bOk, sErr end

LuaLibs/ProcessSimpleScarf.lua

@@ -4,6 +4,7 @@
 -- 2022/08/09 Ora se la feature ha meno di due facce viene richiamata la normale Cut.
 -- 2022/11/09 Aggiunta gestione parametro Q04 per forzare utilizzo fresa di lato e lavorare come FreeContour.
 -- 2023/02/14 Gestite le rotazioni di 90 deg nell'aggiornamento del grezzo.
+-- 2024/08/05 Se assimilabile ad un taglio (1 faccia) si considerare area non pinzabile testa/coda
 
 -- Tabella per definizione modulo
 local ProcessSimpleScarf = {}
@@ -148,7 +149,7 @@ function ProcessSimpleScarf.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, dOvmT
    -- se ci sono meno di due facce si riduce a una normale Cut
    local nFacetCnt = EgtSurfTmFacetCount( Proc.Id)
    if nFacetCnt < 2 then
-      local bOk, sErr = Cut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, nil, nil, nil, nil, nil, dOvmTail)
+      local bOk, sErr = Cut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, nil, nil, nil, nil, nil, dOvmTail, true)
       return bOk, sErr
    end
    -- dati delle facce

LuaLibs/ProcessSplit.lua

@@ -272,7 +272,8 @@ local function AddVerticalPreCuts( Proc, sCutting, dCutXOffset, b3Raw, sNotes)
    for j = nVerticalCuts, 1, -1 do
       local nFaceUse = MCH_MILL_FU.PARAL_FRONT
       local dVerticalCutOffset = dVerticalSliceHeight * -j
-      bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dVerticalCutOffset, 0, 0, sNotes, b3Raw)
+      local bForceTangentLeadInOut = BD.PRESS_ROLLER
+      bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dVerticalCutOffset, 0, 0, sNotes, b3Raw, nil, nil, nil, bForceTangentLeadInOut)
       if not bOk then return bOk, sErr end
    end
    return bOk, sErr
@@ -607,7 +608,8 @@ function ProcessSplit.Make( Proc, nPhase, nRawId, nPartId, nOrd, sDownOrSideOrSt
             for j = nHorizontalCuts, 1, -1 do
                local nFaceUse = MCH_MILL_FU.PARAL_DOWN
                local dHorizontalCutOffset = dHorizontalSliceHeight * -j
-               local bOk, sErr = Fbs.MakeOne( Proc.Id, 0 , sCutting, dSawDiam, nFaceUse, nil, -0.1 - dCutXOffset, BD.CUT_SIC, dHorizontalCutOffset, 0, 0, 'Precut;', b3Raw)
+               local bForceTangentLeadInOut = BD.PRESS_ROLLER
+               local bOk, sErr = Fbs.MakeOne( Proc.Id, 0 , sCutting, dSawDiam, nFaceUse, nil, -0.1 - dCutXOffset, BD.CUT_SIC, dHorizontalCutOffset, 0, 0, 'Precut;', b3Raw, nil, nil, nil, bForceTangentLeadInOut)
                if not bOk then return false, sErr end
             end
             -- se necessario taglio verticale doppio, eseguo l'opposto

LuaLibs/ProcessStepJoint.lua

@@ -212,7 +212,8 @@ local function MakeTwoFaces( Proc, nPhase, nRawId, nPartId, dOvmHead)
          EgtSetInfo( AddId, 'TASKID', Proc.TaskId)
          -- applico lavorazione
          local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead)
          if not bOk then return bOk, sErr end
       end
@@ -223,7 +224,8 @@ local function MakeTwoFaces( Proc, nPhase, nRawId, nPartId, dOvmHead)
          EgtSetInfo( AddId, 'TASKID', Proc.TaskId)
          -- applico lavorazione
          local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead)
          if not bOk then return bOk, sErr end
       end
@@ -392,7 +394,8 @@ local function MakeThreeFaces( Proc, nPhase, nRawId, nPartId, dOvmHead)
       EgtSetInfo( AddId, 'TASKID', Proc.TaskId)
       -- applico lavorazione
       local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                        Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                        Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+      CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
       local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead)
       if not bOk then return bOk, sErr end
    end

LuaLibs/ProcessTenon.lua

@@ -200,7 +200,8 @@ function ProcessTenon.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
          else
             local b3Cut = EgtGetBBoxGlob( AddId or GDB_ID.NULL, GDB_BB.STANDARD)
             local CutProc = { Id = AddId, Grp = Proc.Grp, Prc = Proc.Prc, Box = b3Cut, Fct = 1, Flg = Proc.Flg,
-                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+            CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
             local bFromBottom = ( bShortPart and vtExtr:getZ() > 0.25)
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead, bFromBottom)
             if not bOk then

LuaLibs/ProcessTyroleanDovetail.lua

@@ -232,7 +232,8 @@ local function MakeMachByBlade( Proc, nPhase, nRawId, nPartId, dOvmHead, b3Raw,
       -- se va fatto, inserisco la lavorazione
       if bCut then
          local CutProc = { Id = AuxId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                           Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+         CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
          local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead)
          -- se taglio applicato setto la nota al gruppo Mach per non doverla lavorare una seconda volta
          if bOk then
@@ -330,7 +331,8 @@ local function MakeMachByBlade( Proc, nPhase, nRawId, nPartId, dOvmHead, b3Raw,
          -- se va fatto, inserisco la lavorazione
          if bCut then
             local CutProc = { Id = AuxId, Grp = Proc.Grp, Prc = Proc.Prc, Box = Proc.Box, Fct = Proc.Fct, Flg = Proc.Flg,
-                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId}
+                              Head = Proc.Head, Tail = Proc.Tail, CutId = Proc.CutId, TaskId = Proc.TaskId, PartId = Proc.PartId}
+            CutProc.AffectedFaces = BL.GetProcessAffectedFaces( CutProc)
             local bOk, sErr = Cut.Make( CutProc, nPhase, nRawId, nPartId, dOvmHead)
             -- se taglio applicato setto la nota al gruppo Mach per non doverla lavorare una seconda volta
             if bOk then

UpdateLog.txt

@@ -1,5 +1,19 @@
            ==== Beam Update Log ====
 
+Versione 2.6h1 (20/08/2024)
+- Modif : in SimpleScarf, se assimilabile a un taglio, si considera area non pinzabile
+- Modif : in LapJoint gestito smusso nel caso Groove-Blind-RightAngles-Parallel-4
+- Modif : varie modifiche ai tagli di lama per evitare chiusura rulli pneumatici e finecorsa
+- Modif : in BatchProcessNew, se presente flag apposito in EgtCam5, si evita la generazione
+
+Versione 2.6g4 (19/07/2024)
+- Modif : in BatchProcess e BatchProcessNew si forza ricalcolo ogni volta che si è in situazione di CHECK o CHECK + GENERATE
+
+Versione 2.6g3 (07/07/2024)
+- Added : aggiunta possibilità di funzione GetNzLimDownUp specifica per ogni macchina
+- Modif : anche nel taglio a cubetti si chiama GetNzLimDownUp di macchina, se presente, per decidere limite orientamento lama verso il basso
+- Modif : in BeamExec inserito controllo massimo numero di facce per lanciare GetFacetsInfo
+- Fixed : in LapJoint corretto typo in nome variabile che provocava mancata impostazione asse bloccato
 
 Versione 2.6g2 (04/07/2024)
 - Modif : le lavorazioni BlockHaus, se vicine alla coda, vengono spostate dopo il taglio di separazione

Version.lua

@@ -2,5 +2,5 @@
 -- Gestione della versione di Beam
 
 NAME = 'Beam'
-VERSION = '2.6g2'
+VERSION = '2.6h1'
 MIN_EXE = '2.6e2'