In LongDoubleCut, se la faccia scelta non è completa, si lavora l'altra faccia (se completa)

- in ProcessCut si usano gli offset reali dei cubetti per il calcolo della lunghezza di compensazione per gli attacchi perpendicolari OutRaw

LuaLibs/DiceCut.lua

@@ -566,7 +566,7 @@ function DiceCut.GetDice( nParent, BBoxRawPart, ptCPlanes, vtNPlanes, bGetOrtoPl
       end
    end
 
-   return UltimateTable
+   return UltimateTable, OffsetP, OffsetO
 end
 
 ----------------------------------------------------------------------------------------------------------------------------------------------------

LuaLibs/FacesBySaw.lua

@@ -46,7 +46,7 @@ local BD = require( 'BeamData')
 local ML = require( 'MachiningLib')
 
 ---------------------------------------------------------------------
-function MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, nFaceUse, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, bForceTangentLeadInOut)
+function MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, nFaceUse, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, sLeadInOutType, dActualElevation)
    EgtOutLog( 'FacesBySaw.MakeParallelOne', 3)
    -- dati della faccia
    local ptC, vtN = EgtSurfTmFacetCenter( nSurfId, nFacet, GDB_ID.ROOT)
@@ -68,16 +68,28 @@ function MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, nFaceUse, dVzLimD
    local dLiPerp = dDistX + dCutExtra + dCutSic
    local dLoTang = dLiTang
    local dLoPerp = dLiPerp
+   local dLiCompLength = 0
+   local dLoCompLength = 0
    -- lunghezza attacco/uscita tangenti
    local dLi2Tang = dSawDiam / 2 + dCutSic
    local dLi2Perp = 0
    local dLo2Tang = dLi2Tang
    local dLo2Perp = dLi2Perp
+   local dLi2CompLength = 0
+   local dLo2CompLength = 0
    -- scelgo l'attacco più conveniente
    local bLioTang
    local Ktp = 1.1
    if BD.KIOTP then Ktp = BD.KIOTP end
-   if bForceTangentLeadInOut or ( Ktp * dLi2Tang < dLiPerp) then
+   if ( sLeadInOutType == 'PerpendicularOutraw') then
+      bLioTang = false
+      dLiCompLength = dActualElevation + EgtMdbGetGeneralParam( MCH_GP.SAFEZ) + dCutExtra
+      dLoCompLength = dActualElevation + EgtMdbGetGeneralParam( MCH_GP.SAFEZ) + dCutExtra
+      dLiTang = 1
+      dLoTang = 1
+      dLiPerp = 0
+      dLoPerp = 0
+   elseif ( sLeadInOutType ~= 'Perpendicular') and ( ( sLeadInOutType == 'Tangent') or ( Ktp * dLi2Tang < dLiPerp)) then
       bLioTang = true
       dLiTang, dLiPerp, dLoTang, dLoPerp = dLi2Tang, dLi2Perp, dLo2Tang, dLo2Perp
       if BD.TURN then
@@ -136,9 +148,11 @@ function MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, nFaceUse, dVzLimD
    -- imposto attacco/uscita
    EgtSetMachiningParam( MCH_MP.LITANG, dLiTang)
    EgtSetMachiningParam( MCH_MP.LIPERP, dLiPerp)
+   EgtSetMachiningParam( MCH_MP.LICOMPLEN, dLiCompLength)
    if BD.TURN and bLioTang then EgtSetMachiningParam( MCH_MP.LEADOUTTYPE, MCH_MILL_LO.PERP_TG) end
    EgtSetMachiningParam( MCH_MP.LOTANG, dLoTang)
    EgtSetMachiningParam( MCH_MP.LOPERP, dLoPerp)
+   EgtSetMachiningParam( MCH_MP.LOCOMPLEN, dLoCompLength)
    -- imposto allungamenti iniziale e finale
    EgtSetMachiningParam( MCH_MP.STARTADDLEN, -dAccStart)
    EgtSetMachiningParam( MCH_MP.ENDADDLEN, -dAccEnd)
@@ -157,6 +171,9 @@ function MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, nFaceUse, dVzLimD
    local vtOut = EgtIf( vtN:getX() > 0, X_AX(), -X_AX())
    EgtSetMachiningParam( MCH_MP.BLOCKEDAXIS, BL.GetBlockedAxis( sCutting, 'perpendicular', b3Raw, vtTool, vtOut))
    -- eventuali note
+   if ( sLeadInOutType == 'PerpendicularOutraw') then
+      sNotes = EgtSetValInNotes( sNotes, 'OutRaw', 3)
+   end
    if sNotes and #sNotes > 0 then EgtSetMachiningParam( MCH_MP.USERNOTES, sNotes) end
    -- eseguo
    if not ML.ApplyMachining( true, false) then
@@ -214,7 +231,7 @@ local function GetEdgeToMachineFromVector( nSurfId, nFacet, vtOrthO)
 end
 
 ---------------------------------------------------------------------
-function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, bMaximizeVerticalDepth, bSpecialTangentLeadInOut, bForceTangentLeadInOut, Par5Alternative)
+function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, bMaximizeVerticalDepth, bSpecialTangentLeadInOut, sLeadInOutType, Par5Alternative, dActualElevation)
    -- se lama con asse parallelo alla faccia, passo alla apposita funzione
    if ( Par5 == MCH_MILL_FU.PARAL_DOWN or
         Par5 == MCH_MILL_FU.PARAL_TOP or
@@ -222,7 +239,7 @@ function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDw
         Par5 == MCH_MILL_FU.PARAL_BACK or
         Par5 == MCH_MILL_FU.PARAL_LEFT or
         Par5 == MCH_MILL_FU.PARAL_RIGHT) then
-      return MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, bForceTangentLeadInOut)
+      return MakeParallelOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDwnUp, dCutExtra, dCutSic, dCutOffset, dAccStart, dAccEnd, sNotes, b3Raw, bForceInvert, sLeadInOutType, dActualElevation)
    end
    -- la lama ha asse perpendicolare alla faccia
    EgtOutLog( 'FacesBySaw.MakeOne', 3)
@@ -457,7 +474,17 @@ function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDw
    local bLioTang
    local Ktp = 1.1
    if BD.KIOTP then Ktp = BD.KIOTP end
-   if ( bForceTangentLeadInOut or ( not bDownUp or abs( vtTg:getY()) > 0.5) and
+   if ( sLeadInOutType == 'PerpendicularOutraw') then
+      bLioTang = false
+      dLiCompLength = dActualElevation + EgtMdbGetGeneralParam( MCH_GP.SAFEZ) + dCutExtra
+      dLoCompLength = dActualElevation + EgtMdbGetGeneralParam( MCH_GP.SAFEZ) + dCutExtra
+      dLiTang = 1
+      dLoTang = 1
+      dLiPerp = 0
+      dLoPerp = 0
+      dLenLi = sqrt( dLiTang * dLiTang + dLiPerp * dLiPerp)
+      dLenLo = sqrt( dLoTang * dLoTang + dLoPerp * dLoPerp)
+   elseif ( sLeadInOutType ~= 'Perpendicular') and ( ( sLeadInOutType == 'Tangent') or ( not bDownUp or abs( vtTg:getY()) > 0.5) and
       ( not bDownHead or abs( vtTg:getZ()) < 0.51) and
       abs( vtTg:getX()) < 0.9848 and
       ( ( abs( vtTg:getZ()) < 0.17 and ( vtV1:getZ() < -0.5 or vtV2:getZ() < -0.5) and not bDownHead) or
@@ -603,6 +630,9 @@ function FacesBySaw.MakeOne( nSurfId, nFacet, sCutting, dSawDiam, Par5, dVzLimDw
    local sBlockedAxis = EgtIf( bMaximizeVerticalDepth, 'parallel', 'perpendicular')
    EgtSetMachiningParam( MCH_MP.BLOCKEDAXIS, BL.GetBlockedAxis( sCutting, sBlockedAxis, b3Raw, vtN, vtOrthO))
    -- eventuali note
+   if ( sLeadInOutType == 'PerpendicularOutraw') then
+      sNotes = EgtSetValInNotes( sNotes, 'OutRaw', 3)
+   end
    if sNotes and #sNotes > 0 then EgtSetMachiningParam( MCH_MP.USERNOTES, sNotes) end
    -- eseguo
    if not ML.ApplyMachining( true, false) then

LuaLibs/ProcessCut.lua

@@ -261,7 +261,7 @@ end
 
 ---------------------------------------------------------------------
 -- Applicazione della lavorazione con testa da sopra
-local function MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, bFromBottom, bCustDiceCut, bForced, b3Raw, sNotes, nLimitingSurf, bForceTangentLeadInOut)
+local function MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, bFromBottom, bCustDiceCut, bForced, b3Raw, sNotes, nLimitingSurf, sLeadInOutType)
    local sWarn
    -- ingombro del grezzo
    b3Raw = b3Raw or EgtGetRawPartBBox( nRawId)
@@ -377,6 +377,8 @@ local function MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, b
    -- se lungo, una faccia e rivolto sul retro verso l'alto si forzano i cubetti per evitare di rovinare il pezzo successivo
    local bForceDicing = ( Proc.Fct == 1 and Proc.AffectedFaces.Left and bLongCut and vtN:getZ() > 10 * GEO.EPS_SMALL and vtN:getY() < 10 * GEO.EPS_SMALL)
    local vCuts = {}
+   local dDicingOffsetP
+   local dDicingOffsetO
    if ( ( not Proc.AdvTail) or bForceDicing) and ( dCutH > dMaxDepth - BD.CUT_EXTRA - 3 * BD.COLL_SIC or dCutV > dMaxVertDepth - BD.CUT_EXTRA - 3 * BD.COLL_SIC) then
       local ptExtra, vtExtra
       local bAutoCalcSurf = true
@@ -424,10 +426,10 @@ local function MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, b
       end
       -- se il taglio è più spesso della lama abilito il dicing, altrimenti no
       if ( dMaxElev > dSawThick) or bForceDicing then
-         vCuts = DC.GetDice( nAddGrpId, EgtIf( bForced, b3Raw, b3Solid), ptC, vtN, bAutoCalcSurf, ptExtra, vtExtra, dMaxVertDepth - BD.CUT_EXTRA, dNewDiceDim)
+         vCuts, dDicingOffsetP = DC.GetDice( nAddGrpId, EgtIf( bForced, b3Raw, b3Solid), ptC, vtN, bAutoCalcSurf, ptExtra, vtExtra, dMaxVertDepth - BD.CUT_EXTRA, dNewDiceDim)
          -- se taglio sborda in coda e non è stato inserito nessun taglio a cubetti, lo rilancio con le dimensioni customizzate
          if ( bFillTail or bCustDiceCut) and #vCuts == 0 then
-            vCuts = DC.GetDice( nAddGrpId, b3Solid, ptC, vtN, bAutoCalcSurf, ptExtra, vtExtra, dMaxVertDepth - BD.CUT_EXTRA, Proc.Box:getDimY())
+            vCuts, dDicingOffsetP = DC.GetDice( nAddGrpId, b3Solid, ptC, vtN, bAutoCalcSurf, ptExtra, vtExtra, dMaxVertDepth - BD.CUT_EXTRA, Proc.Box:getDimY())
          end
       end
    end
@@ -596,8 +598,17 @@ local function MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, b
                   if ( i % 2 == 0) and ( Proc.Fct == 1) and bNoPerpCuts then
                      vtOrthoOAlternative = - vtOrthoO
                   end
-                  bForceTangentLeadInOut = bForceTangentLeadInOut and ( ( i % 2) ~= 0)
-                  local bOk, sErr = Fbs.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthoO, dVzLimDwnUp, dExtraCut, BD.CUT_SIC, 0, 0, 0, sNotes, b3Raw, nil, nil, bSpecialTangentLeadInOut, bForceTangentLeadInOut, vtOrthoOAlternative)
+                  local sLeadInOutTypeFbs = 'Calculated'
+                  if ( ( i % 2) ~= 0) then
+                     if ( sLeadInOutType == 'Tangent') then
+                        sLeadInOutTypeFbs = 'Tangent'
+                     elseif ( sLeadInOutType == 'Perpendicular') then
+                        sLeadInOutTypeFbs = 'Perpendicular'
+                     elseif ( sLeadInOutType == 'PerpendicularOutraw') then
+                        sLeadInOutTypeFbs = 'PerpendicularOutraw'
+                     end
+                  end
+                  local bOk, sErr = Fbs.MakeOne( vCuts[i][j], 0, sCutting, dSawDiam, vtOrthoO, dVzLimDwnUp, dExtraCut, BD.CUT_SIC, 0, 0, 0, sNotes, b3Raw, nil, nil, bSpecialTangentLeadInOut, sLeadInOutTypeFbs, vtOrthoOAlternative, dDicingOffsetP)
                   if not bOk then return bOk, sErr end
                end
             end
@@ -838,7 +849,7 @@ end
 
 ---------------------------------------------------------------------
 -- Applicazione della lavorazione
-function ProcessCut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, bFromBottom, bCustDiceCut, bForced, b3Raw, sNotes, dOvmTail, bUpdateIng, nLimitingSurf, bForceTangentLeadInOut)
+function ProcessCut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, bFromBottom, bCustDiceCut, bForced, b3Raw, sNotes, dOvmTail, bUpdateIng, nLimitingSurf, sLeadInOutType)
    -- sovramateriale di coda
    dOvmTail = dOvmTail or BD.OVM_MID
    -- ingombro del grezzo
@@ -878,7 +889,7 @@ function ProcessCut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, bFromBottom,
    local sWarn
    -- se taglio con testa da sopra
    if not bDownHead and not bDownTurn then
-      local bOk, sErr, bNoDicing2 = MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, bFromBottom, bCustDiceCut, bForced, b3Raw, sNotes, nLimitingSurf, bForceTangentLeadInOut)
+      local bOk, sErr, bNoDicing2 = MakeFromTop( sCutting, Proc, nPhase, nRawId, nPartId, dOvmHead, bFromBottom, bCustDiceCut, bForced, b3Raw, sNotes, nLimitingSurf, sLeadInOutType)
       bNoDicing = bNoDicing2
       if not bOk then
          return false, sErr

LuaLibs/ProcessDrill.lua

@@ -546,7 +546,7 @@ function ProcessDrill.Make( Proc, nPhase, nRawId, nPartId)
       if bIntersectionOk then
          local dHoleToCutDistance = vDistance[1]
          -- se il taglio accorcia realmente il foro
-         if dHoleToCutDistance > 10 * GEO.EPS_SMALL and dHoleToCutDistance < dLen then
+         if ( dHoleToCutDistance > 10 * GEO.EPS_SMALL or Proc.AffectedFaces.Right) and dHoleToCutDistance < dLen then
             dMaxDepth = dMaxDepthOri
             dMaxElev = dLen - dHoleToCutDistance
             bTryDrill = true

LuaLibs/ProcessHeadCut.lua

@@ -161,7 +161,7 @@ end
 
 ---------------------------------------------------------------------
 -- tagli verticali aggiuntivi
-local function AddVerticalPreCuts( Proc, sCutting, dCutXOffset, b3Raw)
+local function AddVerticalPreCuts( Proc, sCutting, dCutXOffset, b3Raw, dOffsetBetweenCuts)
    local nVerticalCuts = ceil( Proc.Face[1].WidthTrimmed / ( BD.MAX_LEN_DICE)) - 1
    local dVerticalSliceHeight = Proc.Face[1].WidthTrimmed / ( nVerticalCuts + 1)
    -- recupero il diametro dell'utensile
@@ -177,8 +177,8 @@ local function AddVerticalPreCuts( Proc, sCutting, dCutXOffset, b3Raw)
    for j = nVerticalCuts, 1, -1 do
       local nFaceUse = MCH_MILL_FU.PARAL_FRONT
       local dVerticalCutOffset = dVerticalSliceHeight * -j
-      local bForceTangentLeadInOut = BD.PRESS_ROLLER and not BD.DOWN_HEAD
-      bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dVerticalCutOffset, 0, 0, '', b3Raw, nil, nil, nil, bForceTangentLeadInOut)
+      local sLeadInOutType = 'PerpendicularOutraw'
+      bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dVerticalCutOffset, 0, 0, '', b3Raw, nil, nil, nil, sLeadInOutType, nil, dOffsetBetweenCuts)
       if not bOk then return bOk, sErr end
    end
    
@@ -240,8 +240,8 @@ local function MakeStandardCuts( Proc, b3Raw, nCuts, dOffsetBetweenCuts, HeadCut
             for j = nHorizontalCuts, 1, -1 do
                local nFaceUse = MCH_MILL_FU.PARAL_DOWN
                local dHorizontalCutOffset = dHorizontalSliceHeight * -j
-               local bForceTangentLeadInOut = BD.PRESS_ROLLER
-               local bOk, sErr = Fbs.MakeOne( Proc.Id, 0, Cutting1Data.sCutting, Cutting1Data.dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dHorizontalCutOffset, 0, 0, '', b3Raw, nil, nil, nil, bForceTangentLeadInOut)
+               local sLeadInOutType = 'PerpendicularOutraw'
+               local bOk, sErr = Fbs.MakeOne( Proc.Id, 0, Cutting1Data.sCutting, Cutting1Data.dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dHorizontalCutOffset, 0, 0, '', b3Raw, nil, nil, nil, sLeadInOutType, nil, dOffsetBetweenCuts)
                if not bOk then return bOk, sErr end
             end
             -- se necessario taglio verticale doppio, eseguo l'opposto
@@ -284,7 +284,7 @@ local function MakeStandardCuts( Proc, b3Raw, nCuts, dOffsetBetweenCuts, HeadCut
          local dCutOffset = ( i - 1) * dOffsetBetweenCuts
          -- se trave larga effettuo tagli verticali aggiuntivi
          if HeadCutType.bNeedVerticalAddedCuts then
-            local bOk, sErr = AddVerticalPreCuts( Proc, Cutting1Data.sCutting, dCutOffset, b3Raw)
+            local bOk, sErr = AddVerticalPreCuts( Proc, Cutting1Data.sCutting, dCutOffset, b3Raw, dOffsetBetweenCuts)
             if not bOk then return bOk, sErr end
          end
          if i == 1 and HeadCutType.sType =='Precut' then
@@ -340,7 +340,7 @@ local function MakeStandardCuts( Proc, b3Raw, nCuts, dOffsetBetweenCuts, HeadCut
          end
          -- se trave larga effettuo tagli verticali aggiuntivi
          if HeadCutType.bNeedVerticalAddedCuts then
-            local bOk, sErr = AddVerticalPreCuts( Proc, Cutting1Data.sCutting, dCutOffset, b3Raw)
+            local bOk, sErr = AddVerticalPreCuts( Proc, Cutting1Data.sCutting, dCutOffset, b3Raw, dOffsetBetweenCuts)
             if not bOk then return bOk, sErr end
          end
          local bOk, sErr = Fbs.MakeOne( Proc.Id, 0, Cutting1Data.sCutting, Cutting1Data.dSawDiam, MCH_MILL_FU.ORTHO_DOWN, dVzLimDwnUp, dCutExtra, BD.CUT_SIC, dCutOffset, dAccStart, 0, '', b3Raw)
@@ -498,18 +498,16 @@ function ProcessHeadCut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, bNeedHCut
                         if AreSameVectorApprox( X_AX(), vtNLimitingSurf) then EgtInvertSurf( nLimitingSurf) end
                      end
                      -- tagli verticali
-                     bOk, sErr = AddVerticalPreCuts( AddProc, sCutting, 0, b3Raw)
+                     bOk, sErr = AddVerticalPreCuts( AddProc, sCutting, 0, b3Raw, dOffsL)
                      if not bOk then return bOk, sErr end
                      -- tagli a cubetti con eventuale superficie limitante
-                     bOk, sErr = Cut.Make( AddProc, nPhase, nRawId, nPartId, dOvmHead, nil, false, true, nil, nil, nil, nil, nLimitingSurf)
+                     local sLeadInOutType = 'PerpendicularOutraw'
+                     bOk, sErr = Cut.Make( AddProc, nPhase, nRawId, nPartId, dOvmHead, nil, false, true, nil, nil, nil, nil, nLimitingSurf, sLeadInOutType)
                   end
                -- tagli aggiuntivi non necessari
                else
-                  local bForceTangentLeadInOut = false
-                  if BD.PRESS_ROLLER then
-                     bForceTangentLeadInOut = true
-                  end
-                  bOk, sErr = Cut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, nil, false, true, nil, nil, nil, nil, nil, bForceTangentLeadInOut)
+                  local sLeadInOutType = 'PerpendicularOutraw'
+                  bOk, sErr = Cut.Make( Proc, nPhase, nRawId, nPartId, dOvmHead, nil, false, true, nil, nil, nil, nil, nil, sLeadInOutType)
                end
                return bOk, sErr
             end

LuaLibs/ProcessLongDoubleCut.lua

@@ -286,9 +286,11 @@ local function CalcBladeUse( bUseBlade, bDown_Head, nSide, vtN1, vtN2, bConvex,
                end
             end
          else
-            if ( vtN1 and vtN1:getZ() >= EgtIf( dCustomAngle, dCustomAngle, -0.5)) and ( not vtN2 or vtN2:getZ() >= -0.5) then
-               bCanUseBlade = true
-            end
+            --if ( vtN1 and vtN1:getZ() >= EgtIf( dCustomAngle, dCustomAngle, -0.5)) and ( not vtN2 or vtN2:getZ() >= -0.5) then
+            --   bCanUseBlade = true
+            --end
+            -- viene abilitata sempre lama da sotto
+            bCanUseBlade = true
          end
       end
    end
@@ -423,12 +425,22 @@ function ProcessLong2Cut.Make( Proc, nPhase, nRawId, nPartId, bForcedBladeMaster
    -- analisi del taglio
    local vOrd = {}
    local vFaceUse = {}
+   local bIsMachDownUp = false
    if nSide == 1 or ( nSide == -1 and ( BD.DOWN_HEAD or BD.TURN)) then
       vOrd = EgtIf( ptC[1]:getY() < ptRef:getY(), { 1, 2}, { 2, 1})
       vFaceUse = { BL.GetNearestOrthoOpposite( ptC[1] - ptM), BL.GetNearestOrthoOpposite( ptC[2] - ptM)}
    elseif nSide == -1 then
       vOrd = EgtIf( ptC[1]:getY() < ptRef:getY(), { 1, 2}, { 2, 1})
-      vFaceUse = { BL.GetNearestParalOpposite( ptC[1] - ptM), BL.GetNearestParalOpposite( ptC[2] - ptM)}
+      local vtFaceUse1, vtFaceUse2
+      if bCanUseBlade and not BD.DOWN_HEAD then
+         bIsMachDownUp = true
+         vtFaceUse1 = BL.GetOrtupOpposite( BL.GetNearestOrthoOpposite( ptC[1] - ptM))
+         vtFaceUse2 = BL.GetOrtupOpposite( BL.GetNearestOrthoOpposite( ptC[2] - ptM))
+      else
+         vtFaceUse1 = BL.GetNearestParalOpposite( ptC[1] - ptM)
+         vtFaceUse2 = BL.GetNearestParalOpposite( ptC[2] - ptM)
+      end
+      vFaceUse = { vtFaceUse1, vtFaceUse2}
    else
       local bFront = ( ( vtN[1]:getY() + vtN[2]:getY()) < 0)
       if bFront then
@@ -851,7 +863,7 @@ function ProcessLong2Cut.Make( Proc, nPhase, nRawId, nPartId, bForcedBladeMaster
                   -- imposto la direzione di lavoro per avere scarico del truciolo ottimale
                   local nWorkSide, bInvert
                   if ( not bIsTopBladeCurrent and abs( nSide) ~= 0) or ( bCanUseBlade and bCanUseUnderBlade and nSide == -1) then
-                     if bIsCurrentBladeCCW then
+                     if bIsCurrentBladeCCW and not bIsMachDownUp then
                         nWorkSide = MCH_MILL_WS.LEFT
                         bInvert = true
                         dSal, dEal = dEal, dSal
@@ -860,7 +872,7 @@ function ProcessLong2Cut.Make( Proc, nPhase, nRawId, nPartId, bForcedBladeMaster
                         bInvert = false
                      end
                   else
-                     if bIsCurrentBladeCCW then
+                     if bIsCurrentBladeCCW and not bIsMachDownUp then
                         nWorkSide = MCH_MILL_WS.LEFT
                         bInvert = false
                      else
@@ -1067,6 +1079,11 @@ function ProcessLong2Cut.Make( Proc, nPhase, nRawId, nPartId, bForcedBladeMaster
                if nSide == -1 and BD.DOWN_HEAD then
                   EgtSetMachiningParam( MCH_MP.STARTADDLEN, dEal)
                   EgtSetMachiningParam( MCH_MP.ENDADDLEN, dSal)
+               elseif nSide == -1 and not BD.DOWN_HEAD and bIsMachDownUp then
+                  EgtSetMachiningParam( MCH_MP.INVERT, EgtIf( EgtGetMachiningParam( MCH_MP.INVERT), false, true))
+                  dOffset = 5
+                  EgtSetMachiningParam( MCH_MP.STARTADDLEN, dEal)
+                  EgtSetMachiningParam( MCH_MP.ENDADDLEN, dSal)
                else
                   EgtSetMachiningParam( MCH_MP.STARTADDLEN, dSal)
                   EgtSetMachiningParam( MCH_MP.ENDADDLEN, dEal)
@@ -1289,6 +1306,7 @@ function ProcessLong2Cut.Make( Proc, nPhase, nRawId, nPartId, bForcedBladeMaster
       end
       -- ciclo sulle parti
       local nM = 0
+      local bInverted = false
       for j = 1, nC do
          -- su entrambe le facce
          for i = nIni, nFin do
@@ -1332,8 +1350,19 @@ function ProcessLong2Cut.Make( Proc, nPhase, nRawId, nPartId, bForcedBladeMaster
             -- controllo se lavorazione completa
             local dMachDepth = vElevation[vOrd[i]]
             if dMachDepth > dMaxDepth - 10 * GEO.EPS_ANG_SMALL then
-               sWarn = 'Warning : elevation bigger than max tool depth'
-               EgtOutLog( sWarn)
+               -- verifico se posso lavorare la faccia 2
+               local nOtherFace = EgtIf( i == 1, 2, 1)
+               if j == 1 and vtN[vOrd[nOtherFace]]:getZ() > dLimitAngle and vWidth[vOrd[i]] < dMaxDepth then
+                  vOrd[1], vOrd[2] = vOrd[2], vOrd[1]
+                  dLargh = vWidth[vOrd[i]]
+                  dSal, dEal = dEal, dSal
+                  bInverted = true
+               else
+                  sWarn = 'Warning : elevation bigger than max tool depth'
+                  EgtOutLog( sWarn)
+               end
+            elseif bInverted then
+               dSal, dEal = dEal, dSal
             end
             if not bSide and dLargh > 0.8 * dToolDiam then
                nO = ceil( dLargh / ( 0.6 * dToolDiam))
@@ -1368,7 +1397,7 @@ function ProcessLong2Cut.Make( Proc, nPhase, nRawId, nPartId, bForcedBladeMaster
                --EgtSetMachiningParam( MCH_MP.FACEUSE, EgtIf( bSide, BL.GetParallelOpposite( vFaceUse[vOrd[i]]), vFaceUse[vOrd[i]]))
                EgtSetMachiningParam( MCH_MP.FACEUSE, EgtIf( bSide, MCH_MILL_FU.PARAL_DOWN, vFaceUse[vOrd[i]]))
                -- imposto lato di lavoro e inversione
-               EgtSetMachiningParam( MCH_MP.WORKSIDE, MCH_MILL_WS.LEFT)
+               EgtSetMachiningParam( MCH_MP.WORKSIDE, EgtIf( bIsMachDownUp, MCH_MILL_WS.RIGHT, MCH_MILL_WS.LEFT))
                EgtSetMachiningParam( MCH_MP.INVERT, EgtIf( bSide, true, false))
                -- imposto offset radiale (nullo se concavo o di lato)
                local dOffsR = EgtIf( k < nO, ( nO - k) * dStep, EgtIf( bConvex, - BD.CUT_EXTRA, 0))
@@ -1804,7 +1833,7 @@ function ProcessLong2Cut.Make( Proc, nPhase, nRawId, nPartId, bForcedBladeMaster
                end
             end
             -- imposto lato di lavoro e inversione
-            EgtSetMachiningParam( MCH_MP.WORKSIDE, MCH_MILL_WS.LEFT)
+            EgtSetMachiningParam( MCH_MP.WORKSIDE, EgtIf( bIsMachDownUp, MCH_MILL_WS.RIGHT, MCH_MILL_WS.LEFT))
             EgtSetMachiningParam( MCH_MP.INVERT, true)
             -- calcolo la componente dNz non in base alla classificazione della feature (sopra, sotto, fianchi) ma alla componente maggiore 
 --            local dNz = EgtIf( nSide == 0, vtN[vOrd[i]]:getY(), vtN[vOrd[i]]:getZ())

LuaLibs/ProcessRidgeLap.lua

@@ -173,7 +173,7 @@ function ProcessRidgeLap.Make( Proc, nPhase, nRawId, nPartId, dOvmHead)
       end
       -- calcolo riferimenti per facce inclinate
       local vtRef = Vector3d( vtN[vFaceOrd[3]])
-      local vtRef2 = EgtIf( bHead, X_AX(), -X_AX())
+      local vtRef2 = Vector3d( vtN[vFaceOrd[2]])
       -- eseguo
       for i = 1, #vCuts do
          local nOrthoOpposite

LuaLibs/ProcessSplit.lua

@@ -336,7 +336,7 @@ end
 
 ---------------------------------------------------------------------
 -- tagli verticali aggiuntivi
-local function AddVerticalPreCuts( Proc, sCutting, dCutXOffset, b3Raw, sNotes)
+local function AddVerticalPreCuts( Proc, sCutting, dCutXOffset, b3Raw, sNotes, dOffsetBetweenCuts)
    local nVerticalCuts = ceil( Proc.Face[1].WidthTrimmed / ( BD.MAX_LEN_DICE)) - 1
    local dVerticalSliceHeight = Proc.Face[1].WidthTrimmed / ( nVerticalCuts + 1)
    -- recupero il diametro dell'utensile
@@ -352,8 +352,8 @@ local function AddVerticalPreCuts( Proc, sCutting, dCutXOffset, b3Raw, sNotes)
    for j = nVerticalCuts, 1, -1 do
       local nFaceUse = MCH_MILL_FU.PARAL_FRONT
       local dVerticalCutOffset = dVerticalSliceHeight * -j
-      local bForceTangentLeadInOut = BD.PRESS_ROLLER and not BD.DOWN_HEAD
-      bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dVerticalCutOffset, 0, 0, sNotes, b3Raw, nil, nil, nil, bForceTangentLeadInOut)
+      local sLeadInOutType = 'PerpendicularOutraw'
+      bOk, sErr = Fbs.MakeOne( Proc.Id, 0, sCutting, dSawDiam, nFaceUse, nil, -0.1 -dCutXOffset, BD.CUT_SIC, dVerticalCutOffset, 0, 0, sNotes, b3Raw, nil, nil, nil, sLeadInOutType, nil, dOffsetBetweenCuts)
       if not bOk then return bOk, sErr end
    end
 
@@ -422,8 +422,8 @@ local function MakeStandardCuts( Proc, b3Raw, nCuts, dOffsetBetweenCuts, TailCut
             for j = nHorizontalCuts, 1, -1 do
                local nFaceUse = MCH_MILL_FU.PARAL_DOWN
                local dHorizontalCutOffset = dHorizontalSliceHeight * -j
-               local bForceTangentLeadInOut = BD.PRESS_ROLLER
-               local bOk, sErr = Fbs.MakeOne( Proc.Id, 0 , Cutting1Data.sCutting, Cutting1Data.dSawDiam, nFaceUse, nil, -0.1 - dCutXOffset, BD.CUT_SIC, dHorizontalCutOffset, 0, 0, 'Precut;', b3Raw, nil, nil, nil, bForceTangentLeadInOut)
+               local sLeadInOutType = 'PerpendicularOutraw'
+               local bOk, sErr = Fbs.MakeOne( Proc.Id, 0 , Cutting1Data.sCutting, Cutting1Data.dSawDiam, nFaceUse, nil, -0.1 - dCutXOffset, BD.CUT_SIC, dHorizontalCutOffset, 0, 0, 'Precut;', b3Raw, nil, nil, nil, sLeadInOutType, nil, dOffsetBetweenCuts)
                if not bOk then return false, sErr end
             end
             -- se necessario taglio verticale doppio, eseguo l'opposto
@@ -472,7 +472,7 @@ local function MakeStandardCuts( Proc, b3Raw, nCuts, dOffsetBetweenCuts, TailCut
          -- se trave larga effettuo tagli verticali aggiuntivi
          if TailCutType.bNeedVerticalAddedCuts then
             local sSpecNotes = EgtIf( TailCutType.bSplit, 'Presplit;', 'Precut;')
-            local bOk, sErr = AddVerticalPreCuts( Proc, Cutting1Data.sCutting, dCutOffset, b3Raw, sSpecNotes)
+            local bOk, sErr = AddVerticalPreCuts( Proc, Cutting1Data.sCutting, dCutOffset, b3Raw, sSpecNotes, dOffsetBetweenCuts)
             if not bOk then return bOk, sErr end
          end
          if i == 1 and TailCutType.sType =='Precut' then
@@ -541,7 +541,7 @@ local function MakeStandardCuts( Proc, b3Raw, nCuts, dOffsetBetweenCuts, TailCut
          -- se trave larga effettuo tagli verticali aggiuntivi
          if TailCutType.bNeedVerticalAddedCuts then
             local sSpecNotes = EgtIf( TailCutType.bSplit, 'Presplit;', 'Precut;')
-            local bOk, sErr = AddVerticalPreCuts( Proc, Cutting1Data.sCutting, dCutOffset, b3Raw, sSpecNotes)
+            local bOk, sErr = AddVerticalPreCuts( Proc, Cutting1Data.sCutting, dCutOffset, b3Raw, sSpecNotes, dOffsetBetweenCuts)
             if not bOk then return bOk, sErr end
          end
          local sNotes
@@ -771,18 +771,16 @@ function ProcessSplit.Make( Proc, nPhase, nRawId, nPartId, nOrd, sDownOrSideOrSt
                         if AreOppositeVectorApprox( X_AX(), vtNLimitingSurf) then EgtInvertSurf( nLimitingSurf) end
                      end
                      -- tagli verticali
-                     bOk, sErr = AddVerticalPreCuts( AddProc, sCutting, 0, b3Raw, sNotes)
+                     bOk, sErr = AddVerticalPreCuts( AddProc, sCutting, 0, b3Raw, sNotes, dOffsL)
                      if not bOk then return bOk, sErr end
                      -- tagli a cubetti con eventuale superficie limitante
-                     bOk, sErr = Cut.Make( AddProc, nNewPhase, nRawId, nPartId, dMaxElev, nil, false, true, b3Raw, sNotes, dCurrOvmT, nil, nLimitingSurf)
+                     local sLeadInOutType = 'PerpendicularOutraw'
+                     bOk, sErr = Cut.Make( AddProc, nNewPhase, nRawId, nPartId, dMaxElev, nil, false, true, b3Raw, sNotes, dCurrOvmT, nil, nLimitingSurf, sLeadInOutType)
                   end
                -- tagli aggiuntivi non necessari
                else
-                  local bForceTangentLeadInOut = false
-                  if BD.PRESS_ROLLER then
-                     bForceTangentLeadInOut = true
-                  end
-                  bOk, sErr = Cut.Make( Proc, nNewPhase, nRawId, nPartId, dMaxElev, nil, false, true, b3Raw, sNotes, dCurrOvmT, nil, nil, bForceTangentLeadInOut)
+                  local sLeadInOutType = 'PerpendicularOutraw'
+                  bOk, sErr = Cut.Make( Proc, nNewPhase, nRawId, nPartId, dMaxElev, nil, false, true, b3Raw, sNotes, dCurrOvmT, nil, nil, sLeadInOutType)
                end
                if sNotesFinal then
                   EgtSetMachiningParam( MCH_MP.USERNOTES, sNotesFinal)

Version.lua

@@ -3,4 +3,4 @@
 
 NAME = 'Beam'
 VERSION = '2.7f3'
-MIN_EXE = '2.6e5'
+MIN_EXE = '2.7f2'