// English machine message file  2022/08/27

[MDI]
1=Load tool n° 1
2=Load tool n° 2
3=Load tool n° 3
4=Load tool n° 4
5=Load tool n° 5
6=Load tool n° 6
7=Load tool n° 7
8=Load tool n° 8
9=Load tool n° 9
10=Load tool n° 10
11=Load tool n° 11
12=Load tool n° 12
13=Load tool n° 13
14=Load tool n° 14
15=Load tool n° 15
16=Load tool n° 16
17=Load tool n° 17
18=Load tool n° 18
19=Unload all tool
20=Activate tool magazine
21=Open rotary tool change protection
22=Closed rotary tool change protection
23=Pull up front stop
24=Pull down front stop
25=Pull up lateral stop
26=Pull down side stop
27=Manual tool number assignment in the 5-axis head
28 = Workplan cleaning cycle

[PLC]
1=Machine switched off
2=FREE MESSAGE
3=UPS malfunction in machine electric cabinet
4=UPS battery discharged in machine electric cabinet
5=FREE MESSAGE
6=Home axes B and C not executed
7=FREE MESSAGE
8=Check oil lubrication of chain aggregates
9=Thermal magnetic circuit breaker intervened in machine electric cabinet
10=FREE MESSAGE 
11=FREE MESSAGE 
12=Minimum grease level in the punp
13=Axis lubrication plant fault
14=Compressed air is missing
15=Over temperature in machine electric cabinet left 
16=Over temperature in machine electric cabinet right
17=Electrospindle and motor cooler malfunction
18=FREE MESSAGE 
19=FREE MESSAGE
20=FREE MESSAGE
21=FREE MESSAGE
22=FREE MESSAGE
23=Possible collision electrospindle with rotary tool change
24=X axis drive in alarm
25=Y axis drive in alarm
26=Z axis drive in alarm
27=B axis drive in alarm
28=C axis drive in alarm
29=U axis drive in alarm
30=Y1 axis drive in alarm
31=W axis drive in alarm
32=X axis drive not enabled
33=Y axis drive not enabled
34=Z axis drive not enabled
35=B axis drive not enabled
36=C axis drive not enabled
37=U axis drive not enabled
38=Y1 axis drive not enabled
39=W axis drive not enabled
40=V axis drive in alarm
41=V axis drive not enabled
42=A axis drive in alarm 
43=A axis drive not enabled
44=Rotary tool change warehouse protection open
45=Waiting for insertion of blade motor contactor 
46=Waiting for insertion of electrospindle contactor
47=Electrospindle position not ok for side tool magazine exit
48=Electrospindle position not ok for under beam tool magazine exit
49=Electrospindle position not ok for chain saw tool magazine exit
50=Alarm of safety zones workplan
51=Pre-alarm workplan safety zones
52=FREE MESSAGE
53=Obstacle descent portal suction cap
54=Obstacle descent electrospindle suction cap 
55=Obstacle descent saw blade suction cap
56=Inverter malfunction cportal suction cap
57=Inverter malfunction celectrospindle suction cap 
58=Inverter malfunction csaw blade suction cap
59=*** CE MAINTENANCE ***
60=FREE MESSAGE
61=FREE MESSAGE
62=FREE MESSAGE
63=FREE MESSAGE
64=FREE MESSAGE
65=CRANE IN WORKPLAN
66=FREE MESSAGE
67=FREE MESSAGE
68=FREE MESSAGE
69=FREE MESSAGE
70=FREE MESSAGE
71=FREE MESSAGE
72=FREE MESSAGE
73=FREE MESSAGE
74=FREE MESSAGE
75=FREE MESSAGE
76=FREE MESSAGE
77=FREE MESSAGE
78=FREE MESSAGE
79=FREE MESSAGE
80=FREE MESSAGE
81=Side tool loader not backwards program M90 and then M195
82=Side tool magazine forward sensor not Ok
83=Side tool magazine back sensor not Ok
84=Tool magazine under beam not back program M90 and then M197
85=Under beam tool magazine forward sensor not Ok
86=Under beam tool magazine back sensor not Ok
87=Chain saw tool magazine not back program M90 and then M199
88=Tool magazine chain saw forward Sensor not Ok
89=Tool magazine chain saw back Sensor not Ok
90=FREE MESSAGE
91=FREE MESSAGE
92=Contemporary sensors for side tool change magazine
93=Contemporary sensors for under beam tool change magazine sottotrave
94=Contemporary sensors for chain saw tool change magazine catena
95=Tuning inserted allowed only manual movements
96=FREE MESSAGE
97=FREE MESSAGE
98=FREE MESSAGE
99=FREE MESSAGE
100=FREE MESSAGE
101=Number of revolutions electrospindle or motor not Ok
102=FREE MESSAGE
103=FREE MESSAGE 
104=FREE MESSAGE
105=Rotation electrospindle forbidden without tools
106=FREE MESSAGE
107=FREE MESSAGE
108=Wait for power
109=Press reset button
110=FREE MESSAGE
111=FREE MESSAGE
112=FREE MESSAGE
113=FREE MESSAGE
114=FREE MESSAGE
115=Overtemperature brake resistors mill inverter 
116=Mill Electrospindle overtemperature
117=Saw Motor overtemperature
118=Flow switch Electrospindle not Ok
119=Saw blade Motor flow switch not Ok
120=Overcurrent inverter 
121=Problem on electro-valve or vacuum workplan: zone 1
122=Problem on electro-valve or vacuum workplan: zone 2
123=Problem on electro-valve or vacuum workplan: zone 3
124=Problem on electro-valve or vacuum workplan: zone 4
125=Problem on electro-valve or vacuum workplan: zone 5
126=Problem on electro-valve or vacuum workplan: zone 6
127=Problem on electro-valve or vacuum workplan: zone 7
128=Problem on electro-valve or vacuum workplan: zone 8
129=Problem on electro-valve or vacuum workplan: zone 9
130=Problem on electro-valve or vacuum workplan: zone 10
131=Problem on electro-valve or vacuum workplan: zone 11
132=Problem on electro-valve or vacuum workplan: zone 12
133=Problem on electro-valve or vacuum workplan: zone 13
134=Problem on electro-valve or vacuum workplan: zone 14
135=FREE MESSAGE
136=FREE MESSAGE
137=FREE MESSAGE
138=Switch on the remote control
139=Remote Control Battery Almost Empty
140=FREE MESSAGE
141=FREE MESSAGE
142=Problem on electro-valve or sensor in lateral zero reference workplan 1
143=Problem on electro-valve or sensor in lateral zero reference workplan 2
144=Problem on electro-valve or sensor in lateral zero reference workplan 3
145=Problem on electro-valve or sensor in lateral zero reference workplan 4
146=Problem on electro-valve or sensor in lateral zero reference workplan 5
147=Problem on electro-valve or sensor in lateral zero reference workplan 6
148=Problem on electro-valve or sensor in lateral zero reference workplan 7 
149=Problem on electro-valve or sensor in the front zero reference
150=FREE MESSAGE
151=Electrospindle tool locking defect
152=FREE MESSAGE
153=Tool on Electrospindle with E80001=0
154=FREE MESSAGE
155=Electrospindle tool unlock defect
156=FREE MESSAGE
157=FREE MESSAGE
158=FREE MESSAGE
159=Electrospindle Piston unlocking tool not at rest
160=FREE MESSAGE
161=FREE MESSAGE
162=FREE MESSAGE
163=FREE MESSAGE
164=FREE MESSAGE
165=FREE MESSAGE
166=FREE MESSAGE
167=FREE MESSAGE
168=FREE MESSAGE
200=Defect on one or more EtherCAT modules: restart the machine
201=Function Block Safety in error - input signal discrepancy
202=Safety module communication defect
203=Safety output defect
204=Service Mode ON

[CNC]
1=Unknown character or Axis not recognized by the system
2=Unknown G Function or or a mandatory argument missing after the G
3=Attribute of a G code wrongly positioned
4=Option not enabled or option parameter conflict
5=Geometric Programming Option not enabled
6=Polynomial interpolation option missing
7=Movements parallel to the inclined axes
8=Tool corrector number too high
9=Too many consecutive non executable blocks
10=PLC I/O access: wrong bus exchange
11=PLC I/O access: wrong bus initialization or exchange inhibited
12=PLC I/O access: wrong rack parameter
13=PLC I/O access: card missing
14=Inclined plane option missing - PLC I/O access: channel missing
15=Invalid line configuration
16=Error in activating RTCP
17=Missing closing bracket
18=Servo error: P50 too small
19=RESET RAM at the next power-up
20=M02 missing or blocks left non-executable by a personalized G code
21=Incoherent definition of the blank in 3D
22=Current Part Program corrupted 
24=Error in the definition of an inclined plane
25=Unknown sub-programme or block number
26=Sub-programme nesting too deep
27=Tool Radius Correction
28=Syntax error in CCSPD or working radius definition
29=No programmed range in CCSPD / No suitable range for S in G97
30=Serial line error
31=Mode PPR or PPL impossible with the selected line's protocol
32=Axis referencing error
33=All channels waiting for synchronization
34=Minimum radius for interpolation reached - G21 
35=Searched for block number, not found
36=Part programme memory full
37=Maximum feed exceeded in thread cutting 
38=Control of a spindle already affected to another channel
39=Axis synchronisation fault
40=Excessive following error on axis 0
41=Excessive following error on axis 1
42=Excessive following error on axis 2
43=Excessive following error on axis 3
44=Excessive following error on axis 4
45=Excessive following error on axis 5
46=Excessive following error on axis 6
47=Excessive following error on axis 7
48=Excessive following error on axis 8
49=Excessive following error on axis 9
50=Excessive following error on axis 10
51=Excessive following error on axis 11
52=Excessive following error on axis 12
53=Excessive following error on axis 13
54=Excessive following error on axis 14
55=Excessive following error on axis 15
56=Excessive following error on axis 16
57=Excessive following error on axis 17
58=Excessive following error on axis 18
59=Excessive following error on axis 19
60=Excessive following error on axis 20
61=Excessive following error on axis 21
62=Excessive following error on axis 22
63=Excessive following error on axis 23
64=Excessive following error on axis 24
65=Excessive following error on axis 25
66=Excessive following error on axis 26
67=Excessive following error on axis 27
68=Excessive following error on axis 28
69=Excessive following error on axis 29
70=Excessive following error on axis 30
71=Excessive following error on axis 31
72=Incremental programming after an incomplete block
75=G20 to G21 or G22 transition
76=In G21 : turning or milling fixed cycles are not allowed
77=Tool type not compatible with the operation
78=Syntax error in synchronizing channels
79=Invalid TANDEM Configuration
80=Drive not in HALT
91=Unknown parameter or variable
92=Error in assignment to a parameter or variable
93=Error in the definition of a parameter or in the expression of a test
94=Impossible operation
95=Trying to write to a read only parameter
96=Preceding block "look ahead"
97=Assignment of a parameter in G76 not possible
98=Writing by a channel of a dynamic operator already used by another channel
99=Error associated with the N/M AUTO function
101=PGP: insufficient data in the programming of a circle
102=PGP: when programming a line by angle and one coordinate
106=In G2 G3: 3rd axis programmed without helical option
107=PGP: circle programmed by its radius and end point
110=PGP: syntax error in the first of 2 blocks.
111=PGP: syntax error in the second block.
112=PGP: line-line intersection in which
113=PGP: the values programmed in the two blocks do not allow
114=PGP: intersection or tangent point not defined by ET+ ET- ES+ ES-
121=PGP: syntax error in last of 3 blocks
122=PGP: the first two blocks are non-secant lines
123=PGP: data in the 3 blocks doesn't allow the tangent points to be calculated
124=PGP: tangent point second-third block not defined by ET+ or ET-
130=no axis movement in 1 of the 2 blocks connected by a fillet or chamfer
131=M0,M1 or M2 is not allowed in a block with a fillet or chamfer
135=A chamfer can only be between 2 lines
136=More than 2 non movement blocks between 2 elements whose
137=Change of interpolation plane even though the block is not valid 
138=Change of interpolation plane must be in G40
139=Two parallel [carried] axes programmed in the same block
140=Programming error in radius correction
141=Parallel carried axes : programming a circle whose
143=G73/G74 is not allowed in radius correction mode
144=Quantified axis displacement is different from the Increment
145=G29: abs value  > 1 mm
146=3D Tool offsets, with G29 or G43
148=Number of interpolated axes higher than the maximum allowed
149=Tool radius to large in relation to the programmed trajectory
150=X axis out of limits
151=Y axis out of limits
152=Z axis out of limits
153=U axis out of limits
154=V axis out of limits
155=W axis out of limits
156=A axis out of limits
157=B axis out of limits
158=C axis out of limits
159=Move demanded on a not-homed axis
160=Slave axis homing error
161=Synchro axis homing error
190=Too many nested jumps or loops
191=Syntax error in structured programming
192=Unknown or forbidden key word
193=Structural error
195=Stack overflow
196=Error in the table index declaration
197=Use of an undeclared symbol
198=Syntax error in declaring the symbol for a variable
199=Syntax error in declaring a variable
200=Poor signal or complementarity error on handwheel 0
201=Poor signal or complementarity error on handwheel 1
202=Poor signal or complementarity error on handwheel 2
203=Poor signal or complementarity error on handwheel 3
210=Poor signal or channel loss or serial feedback fault on axis 0
211=Poor signal or channel loss or serial feedback fault on axis 1
212=Poor signal or channel loss or serial feedback fault on axis 2
213=Poor signal or channel loss or serial feedback fault on axis 3
214=Poor signal or channel loss or serial feedback fault on axis 4
215=Poor signal or channel loss or serial feedback fault on axis 5
216=Poor signal or channel loss or serial feedback fault on axis 6
217=Poor signal or channel loss or serial feedback fault on axis 7
218=Poor signal or channel loss or serial feedback fault on axis 8
219=Poor signal or channel loss or serial feedback fault on axis 9
220=Poor signal or channel loss or serial feedback fault on axis 10
221=Poor signal or channel loss or serial feedback fault on axis 11
222=Poor signal or channel loss or serial feedback fault on axis 12
223=Poor signal or channel loss or serial feedback fault on axis 13
224=Poor signal or channel loss or serial feedback fault on axis 14
225=Poor signal or channel loss or serial feedback fault on axis 15
226=Poor signal or channel loss or serial feedback fault on axis 16
227=Poor signal or channel loss or serial feedback fault on axis 17
228=Poor signal or channel loss or serial feedback fault on axis 18
229=Poor signal or channel loss or serial feedback fault on axis 19
230=Poor signal or channel loss or serial feedback fault on axis 20
231=Poor signal or channel loss or serial feedback fault on axis 21
232=Poor signal or channel loss or serial feedback fault on axis 22
233=Poor signal or channel loss or serial feedback fault on axis 23
234=Poor signal or channel loss or serial feedback fault on axis 24
235=Poor signal or channel loss or serial feedback fault on axis 25
236=Poor signal or channel loss or serial feedback fault on axis 26
237=Poor signal or channel loss or serial feedback fault on axis 27
238=Poor signal or channel loss or serial feedback fault on axis 28
239=Poor signal or channel loss or serial feedback fault on axis 29
240=Poor signal or channel loss or serial feedback fault on axis 30
241=Poor signal or channel loss or serial feedback fault on axis 31
245=Digital servo loop fault
246=Bad homing reference mark detected
247=Drive parameter fault DISC NT
248=Axis drive or digital spindle fault
249=Communication error between CNC and PLC
250=Invalid PERSOChip
251=Inconsistent PERSOChip Data 
252=Invalid Licence File
253=Nesting of subroutines called by M function not allowed
260=Executive memory busy
261=Programme number too high
262=NU number not amongst those authorised
263=TEST or GRAPHIC mode obligatory after initial load or modification
264=No  dimension in the profiling plane or dimension outside plane
265=First positioning block missing
266=Insufficient memory
267=Invalid character in pocket syntax
268=Incomplete pocket block or containing unauthorised data
269=Incomplete profiling block
270=Pocket definition, partially or totally missing
271=Tool orientation not perpendicular in relation to profiling plane
272=Real tool incompatible with pocket machining data
273=Change of profiling plane between pocket definition and execution
274=Two pocket definitions overlapped
275=NU0 programmed with 59
276=Zero pocket depth
277=Incomplete start or end point coordinates in pocket definition
278=Spindle rotation inconsistent with that requested in pocket definition
279=G Function unauthorised in pocket programming block
280=First profiling block incomplete
281=Profile inconsistency
282=Incorrect pocket parameters
283=Outer profile must exist and be unique
284=Error in profile definition
285=Too many profiles
286=Tool pass too great relative to the tool diameter
287=Tool pass too shallow in relation to the dimensions
288=Finishing OP start point at a re-entrant angle or an area not yet
289=Tool diameter too large
290=Pocket: Internal error
291=Finishing start point outside the profile
292=Double positioning at start of profile
293=Rough end point found in face milling section
300=Axis 0 declared in P2 but not detected on the bus or feedback fault
301=Axis 1 declared in P2 but not detected on the bus or feedback fault
302=Axis 2 declared in P2 but not detected on the bus or feedback fault
303=Axis 3 declared in P2 but not detected on the bus or feedback fault
304=Axis 4 declared in P2 but not detected on the bus or feedback fault
305=Axis 5 declared in P2 but not detected on the bus or feedback fault
306=Axis 6 declared in P2 but not detected on the bus or feedback fault
307=Axis 7 declared in P2 but not detected on the bus or feedback fault
308=Axis 8 declared in P2 but not detected on the bus or feedback fault
309=Axis 9 declared in P2 but not detected on the bus or feedback fault
310=Axis 10 declared in P2 but not detected on the bus or feedback fault
311=Axis 11 declared in P2 but not detected on the bus or feedback fault
312=Axis 12 declared in P2 but not detected on the bus or feedback fault
313=Axis 13 declared in P2 but not detected on the bus or feedback fault
314=Axis 14 declared in P2 but not detected on the bus or feedback fault
315=Axis 15 declared in P2 but not detected on the bus or feedback fault
316=Axis 16 declared in P2 but not detected on the bus or feedback fault
317=Axis 17 declared in P2 but not detected on the bus or feedback fault
318=Axis 18 declared in P2 but not detected on the bus or feedback fault
319=Axis 19 declared in P2 but not detected on the bus or feedback fault
320=Axis 20 declared in P2 but not detected on the bus or feedback fault
321=Axis 21 declared in P2 but not detected on the bus or feedback fault
322=Axis 22 declared in P2 but not detected on the bus or feedback fault
323=Axis 23 declared in P2 but not detected on the bus or feedback fault
324=Axis 24 declared in P2 but not detected on the bus or feedback fault
325=Axis 25 declared in P2 but not detected on the bus or feedback fault
326=Axis 26 declared in P2 but not detected on the bus or feedback fault
327=Axis 27 declared in P2 but not detected on the bus or feedback fault
328=Axis 28 declared in P2 but not detected on the bus or feedback fault
329=Axis 29 declared in P2 but not detected on the bus or feedback fault
330=Axis 30 declared in P2 but not detected on the bus or feedback fault
331=Axis 31 declared in P2 but not detected on the bus or feedback fault
400=Loading dyn ops in C: The size of user code is too big
401=Loading dyn ops in C: Format error
402=Loading dyn ops in C: Checksum error
403=The system has insufficient memory for dyn ops in C
404=Loading dyn ops in C: Open error
405=Loading dyn ops in C: Read error
406=Loading dyn ops in C: Close error
407=Loading dyn ops in C: The directory is empty
410=Dyn ops in C: Number of parameters passed doesn't tally
411=Dyn ops in C: user error from init: negative return
413=Unrecognised dyn ops in C
414=Dyn ops in C without MAIN
420=Dynops in C: USER ERROR from the QUIT function
421=Dynops in C: USER ERROR from the QUIT function: negative return
423=Dynops in C: Range of function in C not from 0 at 100
424=Floating point unit exception error
900=Invalid tool number M6T
901=Tool number loaded not OK
902=Invalid tool number E80001 on electrospindle
903=Sensor home B electrospindle not OK
904=Sensor home C electrospindle not OK
905=Sensor home B motor saw blade not OK
906=Sensor home C motor saw blade not OK
907=free message
908=free message
909=free message
910=free message
911=free message
912=free message
913=free message
914=free message  
915=free message 
916=Define spindle number et.. (1=blade 2=mill 3=right driller 4=left driller)
917=free message
918=free message
919=free message
920=free message
921=free message
922=free message
923=free message
924=OFFSET X SAW BLADE NOT ALIGNED BETWEEN MACHINE AND CADCAM
925=OFFSET Y SAW BLADE NOT ALIGNED BETWEEN MACHINE AND CADCAM
926=OFFSET Z SAW BLADE NOT ALIGNED BETWEEN MACHINE AND CADCAM
927=PIVOT Z SAW BLADE NOT ALIGNED BETWEEN MACHINE AND CADCAM
928=PIVOT C SAW BLADE NOT ALIGNED BETWEEN MACHINE AND CADCAM
929=OFFSET X MILL NOT ALIGNED BETWEEN MACHINE AND CADCAM
930=OFFSET Y MILL NOT ALIGNED BETWEEN MACHINE AND CADCAM
931=OFFSET Z MILL NOT ALIGNED BETWEEN MACHINE AND CADCAM
932=PIVOT Z MILL NOT ALIGNED BETWEEN MACHINE AND CADCAM
933=Mandatory X-U-W-Z programming with G102EH.. not zero
934=free message
935=free message
936=free message
937=free message
938=free message
939=free message
1050=No communication with the NC
1206=Axes Moving
1207=Program in execution
1604=Program being executed
2001=Flexium system has not been shutdown correctly. Some programs may not be up to date. The programs need to be checked in the programming page
2007=Flexium System was not shutdown correctly! Previous Zone 0 files are transfered to the NCK
5000=No communication with Flexium RTS

[INPUT]
1=MACHINE ON
2=MOTOR THERMOELEMENTS
3=REMOTE SWITCH ELECTRICSPINDLE INSERTED
4=SUCTION CAP PORTAL MOTOR DRIVE OK
5=SUCTION CAP ELECTRICSPINDLE MOTOR DRIVE OK
6=THERMAL PROBE - INVERTER BRAKE RESISTANCE
7=SUCTION CAP SAW BLADE MOTOR DRIVE OK
8=SENSOR HIGH UP SUCTION CAP PORTAL
9=SENSOR LOW-DOWN UP SUCTION CAP PORTAL
10=MAINTENANCE SELECTION MACHINE CE
11=SENSOR HIGH UP SUCTION CAP ELECTRICSPINDLE
12=SENSOR LOW-DOWN UP SUCTION CAP ELECTRICSPINDLE
13=SENSOR HIGH UP SUCTION CAP SAW BLADE MOTOR
14=SENSOR LOW-DOWN UP SUCTION CAP SAW BLADE MOTOR
15=SENSOR CHANGING ROTATIVE UTENSILE PROTECTION OPENED
16=FREE INPUT
17=FREE INPUT
18=FREE INPUT
19=FREE INPUT
20=FREE INPUT
21=FREE INPUT
22=FREE INPUT
23=SENSOR FORWARD CHAIN SAW TOOL CHANGE
24=SENSOR BACKWARDS CHAIN SAW TOOL CHANGE
25=THERMAL PROBE SENSOR ELECTRICSPINDLE
26=THERMAL PROBE SENSOR SAW BLADE MOTOR 
27=FREE INPUT
28=SENSOR FORWARD SIDE TOOL CHANGE
29=SENSOR BACKWARDS SIDE TOOL CHANGE
30=ELECTRICSPINDLE AND SAW BLADE MOTOR COOLER OK
31=ELECTRICSPINDLE FLOW SWITCH
32=ALARM RESET BUTTON
33=PRESSURE DEVICE AXES LUBRICATION
34=PRESSURE DEVICE COMPRESSED AIR 
35=SENSOR MINIMUM GREASE LEVEL
36=SENSOR MINIMUM OIL LEVEL
37=FREE INPUT
38=OVER TEMPERATURE LEFT CABINET
39=SENSOR UNLOCKED PISTON CONE AT REST
40=PRE-ALARM WORKPLAN SAFETY ZONES
41=SAW BLADE MOTOR FLOW SWITCH
42=REMOTE SWITCH SAW BLADE MOTOR INSERTED
43=SENSOR FORWARD UNDER BEAM TOOL CHANGE
44=SENSOR BACKWARDS UNDER BEAM TOOL CHANGE
45=ALARM OF SAFETY ZONES WORKPLAN
46=FREE INPUT
47=UPS BATTERY OK
48=UPS-CURRENT OUTPUT
49=SENSOR LOW-DOWN FRONTAL STOP 
50=SENSOR LOW-DOWN LATERAL STOP WORKPLAN 1
51=SENSOR LOW-DOWN LATERAL STOP WORKPLAN 2
52=SENSOR LOW-DOWN LATERAL STOP WORKPLAN 3
53=SENSOR LOW-DOWN LATERAL STOP WORKPLAN 4
54=SENSOR LOW-DOWN LATERAL STOP WORKPLAN 5
55=SENSOR LOW-DOWN LATERAL STOP WORKPLAN 6
56=FREE INPUT
57=FREE INPUT
58=SELECTOR CONVEYOR BELT ACTIVATION
59=FREE INPUT
60=FREE INPUT
61=FREE INPUT
62=FREE INPUT
63=OVER TEMPERATURE RIGHT CABINET
64=FREE INPUT
65=VACUUM RESERVATION ZONE 1
66=VACUUM RESERVATION ZONE 2
67=VACUUM RESERVATION ZONE 3
68=VACUUM RESERVATION ZONE 4
69=VACUUM RESERVATION ZONE 5
70=VACUUM RESERVATION ZONE 6
71=VACUUM RESERVATION ZONE 7
72=VACUUM RESERVATION ZONE 8
73=VACUUM RESERVATION ZONE 9
74=VACUUM RESERVATION ZONE 10
75=VACUUM RESERVATION ZONE 11
76=VACUUM RESERVATION ZONE 12
77=FREE INPUT
78=FREE INPUT
79=FREE INPUT
80=FREE INPUT
81=VACUUM SWITCH ZONE 1
82=VACUUM SWITCH ZONE 2
83=VACUUM SWITCH ZONE 3
84=VACUUM SWITCH ZONE 4
85=VACUUM SWITCH ZONE 5
86=VACUUM SWITCH ZONE 6
87=VACUUM SWITCH ZONE 7
88=VACUUM SWITCH ZONE 8
89=VACUUM SWITCH ZONE 9
90=VACUUM SWITCH ZONE 10
91=VACUUM SWITCH ZONE 11
92=VACUUM SWITCH ZONE 12
93=FREE INPUT
94=FREE INPUT
95=FREE INPUT
96=FREE INPUT

[OUTPUT]
1=CONTROL, DRY AIR SOLENOID VALVE OPENING
2=CE REGULATION MODE CONSENT
3=SELECTION HOME AXIS C1 ELECTRICSPINDLE
4=SELECTION HOME AXIS C2 SAW BLADE MOTOR
5=OPENINGOF THE SOLENOID VALVE OF THE ROTARY TOOL CHANGE PROTECTION
6=CLOSINGOF THE SOLENOID VALVE OF THE ROTARY TOOL CHANGE PROTECTION
7=HOURCOUNTER
8=REMOTE SWITCH ARMING ELECTRICSPINDLE
9=SCRAPS CONVEYOR BELT
10=AXIS MOTOR PUMP LUBRICATION
11=SOLENOID VALVE LUBRICATION CHAIN
12=FREE OUTPUT
13=MESSAGES LAMP
14=FREE OUTPUT
15=FREE OUTPUT
16=REMOTE SWITCH ARMING SAW BLADE MOTOR
17=SOLENOID VALVE TOOL LOCK
18=SOLENOID VALVE TOOL UNLOCK
19=FREE OUTPUT
20=SOLENOID VALVE LATERAL TOOL CHANGE FORWARD
21=SOLENOID VALVE LATERAL TOOL CHANGE BACKWARD
22=SOLENOID VALVE CHAIN TOOL CHANGE FORWARD
23=SOLENOID VALVE CHAIN TOOL CHANGE BACKWARD
24=SOLENOID VALVE CHAIN CLEANING BLOW
25=SOLENOID VALVE CLIMB FRONTAL RIGHT STOP
26=SOLENOID VALVE CLIMB LATERAL WORKPLAN 1
27=SOLENOID VALVE CLIMB LATERAL WORKPLAN 2
28=SOLENOID VALVE CLIMB LATERAL WORKPLAN 3
29=SOLENOID VALVE CLIMB LATERAL WORKPLAN 4
30=SOLENOID VALVE CLIMB LATERAL WORKPLAN 5
31=SOLENOID VALVE CLIMB LATERAL WORKPLAN 6
32=SOLENOID VALVE CLIMB LATERAL WORKPLAN 7
33=SOLENOID VALVE ELECTRICSPINDLE BLOW
34=SOLENOID VALVE TOOL CHANGE UNDER BEAM FORWARD
35=SOLENOID VALVE TOOL CHANGE UNDER BEAM BACWARD
36=SOLENOID VALVE AXIS ELECTRICSPINDLE CLEANING BLOW
37=SOLENOID VALVE FRONTAL BLOW
38=SOLENOID VALVE LATERAL BLOW
39=VACUUM REQUEST ENABLE 
40=OPEN VACUUM
41=SOLENOID VALVE VACUUM OPEN ZONE 1
42=SOLENOID VALVE VACUUM OPEN ZONE 2
43=SOLENOID VALVE VACUUM OPEN ZONE 3
44=SOLENOID VALVE VACUUM OPEN ZONE 4
45=SOLENOID VALVE VACUUM OPEN ZONE 5
46=SOLENOID VALVE VACUUM OPEN ZONE 6
47=SOLENOID VALVE VACUUM OPEN ZONE 7
48=SOLENOID VALVE VACUUM OPEN ZONE 8
49=SOLENOID VALVE VACUUM OPEN ZONE 9
50=SOLENOID VALVE VACUUM OPEN ZONE 10
51=SOLENOID VALVE VACUUM OPEN ZONE 11
52=SOLENOID VALVE VACUUM OPEN ZONE 12
53=SOLENOID VALVE VACUUM OPEN ZONE 13
54=SOLENOID VALVE VACUUM OPEN ZONE 14
55=FREE OUTPUT
56=SOLENOID VALVE AXIS MOTOR SAW BLADE CLEANING BLOW
57=VACUUM PRESSURE
58=PORTAL ASPIRATION SUCTION CAP RISE
59=PORTAL ASPIRATION SUCTION CAP DESCEND
60=PORTAL SUCTION CAP FAST COMMAND
61=PORTAL SUCTION CAP BRAKE UNLOCK
62=ELECTRICSPINDLE SUCTION CAP RISE
63=ELECTRICSPINDLE SUCTION CAP DESCEND
64=ELECTRICSPINDLE SUCTION CAP FAST COMMAND
65=ELECTRICSPINDLE SUCTION CAP BRAKE UNLOCK
66=MOTOR SAW BLADE SUCTION CAP RISE
67=MOTOR SAW BLADE SUCTION CAP DESCEND
68=MOTOR SAW BLADE SUCTION CAP FAST COMMAND
69=MOTOR SAW BLADE SUCTION CAP BRAKE UNLOCK
70=SOLENOID VALVE CLEANING AIR TANK LOAD RIGHT
71=SOLENOID VALVE OPENING BLOW CLEANING CABIN RIGHT
72=SOLENOID VALVE CLEANING AIR TANK LOAD LEFT
73=SOLENOID VALVE BLOW CLEANING CABIN LEFT
74=SOLENOID VALVE BLOW CAMERA CLEANING
75=SOLENOID VALVE SUCTION CAP ELECTRICSPINDLE
76=SOLENOID VALVE SUCTION CAP SAW MOTOR
77=SOLENOID VALVE SUCTION CAP PORTAL
78=SOLENOID VALVE SUCTION CAP PORTAL CLEANING
79=OUTPUT MACHINE IN PARKING POSITION
80=OUTPUT ZERO REFERENCE WORKPLAN LOW-DOWN
81=OUTPUT SCRAPS CONVEYOR BELT ROTATING
82=OUTPUT MACHINE SWITCHED ON
83=OUTPUT ALARM OF SAFETY ZONES WORKPLAN
84=FREE OUTPUT
85=FREE OUTPUT
86=FREE OUTPUT
87=FREE OUTPUT
88=FREE OUTPUT
89=FREE OUTPUT
90=FREE OUTPUT
91=FREE OUTPUT
92=FREE OUTPUT
93=FREE OUTPUT
94=FREE OUTPUT
95=FREE OUTPUT
96=FREE OUTPUT
