Tolti i 100mm aggiuntivi al calcolo ZMAX

Common_ONE-PF.NUM.mlpe

@@ -684,6 +684,10 @@ function OnPathEnd()
    if not EMT.ZMAX then
       EmitResetMachining()
    end
+
+   -- salvo dati precedenti
+   EMT.L2pp = EMT.L2o
+
    EMT.AUXTYPE = nil
    EMT.UNL = nil
    EMT.PREROT = nil
@@ -868,14 +872,20 @@ function OnRapid()
                   bMoveZbeforeX = true
                end
 
+               -- se vado in posizione speciale rotazione assi, poi devo ritornare alla X vera di lavoro
+               local dMoveXtoFinalPosition = false
                local dXref = EMT.L2
                if  EMT.HEAD == 'H12'  and  EMT.L2 < -LimX1PlRotSaw  then
                   dXref = -LimX1PlRotSaw
                   EmitMoveDataHead( 1, { X=dXref, Z=MyMaxZ1, B=ParkB1, C=ParkC1, S=Speed})
+                  dZref = min( dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2), MyMaxZ1)
+                  dMoveXtoFinalPosition = true
                elseif not bMoveZbeforeX then
                   EmitMoveDataHead( 1, { X=dXref, Z=MyMaxZ1, B=ParkB1, C=ParkC1, S=Speed})
                else
                   EmitMoveDataHead( 1, { X=-LimX1PlRotSaw, Z=MyMaxZ1, B=ParkB1, C=ParkC1, S=Speed})
+                  dZref = min( dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2), MyMaxZ1)
+                  dMoveXtoFinalPosition = true
                end
    
                -- caso speciale per trave alta con rotazione lama pericolosa (tolto "and EMT.SB > 379")
@@ -886,6 +896,9 @@ function OnRapid()
                   if bMoveZbeforeX then
                      EmitMoveDataHead( 1, { Z=EMT.L3, S=Speed})
                   end
+                  if dMoveXtoFinalPosition then
+                     EmitMoveDataHead( 1, { X=EMT.L2, S=Speed})
+                  end
                -- caso standard
                else
                   EmitMoveDataHead( 1, { X=dXref, Z=dZref, B=ParkB1, C=ParkC1, S=Speed})
@@ -1121,7 +1134,7 @@ function OnRapid()
             end
             bToPresel = false
             -- risalita a Zmax
-            EmitZmax( false, false, EMT.TO_XHOME, PrevR1, PrevR2)
+            EmitZmax( false, false, EMT.TO_XHOME, PrevR1, PrevR2, nil, true)
             EMT.ZMAX = true
             EMT.TO_ZMAX = nil
             EMT.TO_XHOME = nil
@@ -1139,37 +1152,17 @@ function OnRapid()
          if EMT.TO_XHOME then
             local nHSet = GetHeadSet( EMT.HEAD)
             local nPrevHSet = GetHeadSet( EMT.PREVHEAD)
-
+            if EMT.PREVHEAD == 'H12' or EMT.PREVHEAD == 'H22' then
-            -- se successivo non è sega a catena e la testa è la stessa, vado in home con utensile succesivo
+               if nPrevHSet == 1 then
-            if not HeadIsChainSaw( EMT.HEAD) and nHSet == nPrevHSet then
-               if nHSet == 1 then
                   local HomeX1 = EgtGetAxisHomePos( 'X1')
-                  EmitMoveDataHead( 1, { X=-HomeX1, Z=MaxZ1, B=ParkB1, C=ParkC1})
+                  EmitMoveDataHead( 1, { X=-EMT.PREVHOMEX_H1, Z=MaxZ1, B=ParkB1, C=ParkC1, TPos=AdjustTcPos( false, EMT.PREVTCPOS_H1)})
                   EmitMoveStartHead( 1, 'EA1')
+                  EmitMoveWaitHead( 1)
                else
                   local HomeX2 = EgtGetAxisHomePos( 'X2')
-                  EmitMoveDataHead( 2, { X=-HomeX2, Z=MaxZ2, B=ParkB2, C=ParkC2})
+                  EmitMoveDataHead( 2, { X=-EMT.PREVHOMEX_H2, Z=MaxZ2, B=ParkB2, C=ParkC2, TPos=AdjustTcPos( false, EMT.PREVTCPOS_H2)})
                   EmitMoveStartHead( 2, 'EA1')
-               end
+                  EmitMoveWaitHead( 2)
-            else
-               if not HeadIsChainSaw( EMT.PREVHEAD) then
-                  if nPrevHSet == 1 then
-                     local HomeX1 = EgtGetAxisHomePos( 'X1')
-                     EmitMoveDataHead( 1, { X=-EMT.PREVHOMEX_H1, Z=MaxZ1, B=ParkB1, C=ParkC1, TPos=AdjustTcPos( false, EMT.PREVTCPOS_H1)})
-                     EmitMoveStartHead( 1, 'EA1')
-                  else
-                     local HomeX2 = EgtGetAxisHomePos( 'X2')
-                     EmitMoveDataHead( 2, { X=-EMT.PREVHOMEX_H2, Z=MaxZ2, B=ParkB2, C=ParkC2, TPos=AdjustTcPos( false, EMT.PREVTCPOS_H2)})
-                     EmitMoveStartHead( 2, 'EA1')
-                  end
-               else
-                  if GetHeadTCSet( EMT.PREVHEAD, EMT.PREVTCPOS) == 'Head1_TC1' or GetHeadTCSet( EMT.PREVHEAD, EMT.PREVTCPOS) == 'Head1_TC2' then
-                     EmitMoveDataHead( 1, { X=-ParkCSawX1S, Z=MaxZ1, B=HomeR2, C=HomeR1, TPos='50'})
-                     EmitMoveStartHead( 1, 'EA1')
-                  else
-                     EmitMoveDataHead( 2, { X=-ParkCSawX2S, Z=MaxZ2, B=HomeR2, C=HomeR1, TPos='50'})
-                     EmitMoveStartHead( 2, 'EA1')
-                  end
                end
             end
 
@@ -1234,14 +1227,20 @@ function OnRapid()
                      bMoveZbeforeX = true
                   end
 
+               -- se vado in posizione speciale rotazione assi, poi devo ritornare alla X vera di lavoro
+                  local dMoveXtoFinalPosition = false
                   local dXref = EMT.L2
                   if  EMT.HEAD == 'H12'  and  EMT.L2 < -LimX1PlRotSaw  then
                      dXref = -LimX1PlRotSaw
                      EmitMoveDataHead( 1, { X=dXref, Z=CurrZ1, B=CurrB1, C=CurrC1, TRad=dTRad, TLen=dTLen, S=Speed})
-                  elseif not bMoveZbeforeX then
+                     dZref = min( dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2), MyMaxZ1)
+                     dMoveXtoFinalPosition = true
+                     elseif not bMoveZbeforeX then
                      EmitMoveDataHead( 1, { X=dXref, Z=CurrZ1, B=CurrB1, C=CurrC1, TRad=dTRad, TLen=dTLen, S=Speed})
                   else
                      EmitMoveDataHead( 1, { X=CurrX1, Z=CurrZ1, B=CurrB1, C=CurrC1, TRad=dTRad, TLen=dTLen, S=Speed})
+                     dZref = min( dSafeZ1 + GetZExtra( EMT.HEAD, EMT.R2), MyMaxZ1)
+                     dMoveXtoFinalPosition = true
                   end
 
                   -- caso speciale per trave alta con rotazione lama pericolosa (tolto "and EMT.SB > 379")
@@ -1252,6 +1251,9 @@ function OnRapid()
                      if bMoveZbeforeX then
                         EmitMoveDataHead( 1, { Z=EMT.L3, S=Speed})
                      end
+                     if dMoveXtoFinalPosition then
+                        EmitMoveDataHead( 1, { X=EMT.L2, S=Speed})
+                     end
                   -- altrimenti caso standard
                   else
                      EmitMoveDataHead( 1, { Z=dZref, S=Speed})
@@ -2686,6 +2688,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
    end
    -- gruppo della testa
    local nHSet = GetHeadSet( EMT.HEAD)
+   local dXPos = EgtIf( bUsePrevDelta, EMT.L2pp or EMT.L2o, EMT.L2o)
    -- reset stato di testa in home
    EMT.XHOME = nil
    -- se testa 1
@@ -2707,12 +2710,12 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
             -- eseguo la salita a Z1max (oriento solo se assi rotanti non già a posto)
             if abs( dSafeC1 - PrevR1) > 0.1 or abs( dSafeB1 - PrevR2) > 0.1 then
                local dZref = dSafeZ1 + GetZExtra( EMT.HEAD, PrevR2)
-               if EgtIf( BD.RIGHT_LOAD, -EMT.L2o < -LimX1RotSaw, -EMT.L2o > -LimX1RotSaw) then
+               if EgtIf( BD.RIGHT_LOAD, -dXPos < -LimX1RotSaw, -dXPos > -LimX1RotSaw) then
                   dZref = dZref - EgtIf( not Mortiser, 100, 370)
                end
                dZref = min( dZref, dMaxZ1)
                local MovH = { Z = EgtIf( dZref > EMT.L3o, dZref, EMT.L3o)}
-               MovH.X = -EMT.L2o ; MovH.B = EgtClamp( PrevR2, -90, 90) ;  MovH.C = PrevR1 ;
+               MovH.X = -dXPos ; MovH.B = EgtClamp( PrevR2, -90, 90) ;  MovH.C = PrevR1 ;
                EmitMoveDataHead( 1, MovH)
                if EMT.HEAD == 'H12' and ( abs( dSafeC1 - PrevR1) > 30.1 or abs( dSafeB1 - PrevR2) > 30.1) then
                   EmitMoveDataHead( 1, { Z=dMaxZ1, B=0})
@@ -2722,7 +2725,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
                EmitMoveDataHead( 1, { Z=dMaxZ1})
             else
                local MovH = { Z = dMaxZ1}
-               MovH.X = -EMT.L2o ; MovH.B = PrevR2 ; MovH.C = PrevR1 ;
+               MovH.X = -dXPos ; MovH.B = PrevR2 ; MovH.C = PrevR1 ;
                EmitMoveDataHead( 1, MovH)
             end
             if bXhome then 
@@ -2738,7 +2741,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
          -- altrimenti sega a catena
          else
             -- ribadisco movimento perchè in G141 si aspetta sempre tutti i valori
-            local MovH = { X = -EMT.L2o, Z = EMT.L3o, B = PrevR2, C = PrevR1}
+            local MovH = { X = -dXPos, Z = EMT.L3o, B = PrevR2, C = PrevR1}
             EmitMoveDataHead( 1, MovH)
             EmitMoveDataHead( 1, { Z=dSafeZ1, B=dSafeB1})
             if EMT.SB > 650 and abs( EMT.R3) < 0.1 then
@@ -2761,7 +2764,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
                local dZref = dSafeZ1 + GetZExtra( EMT.HEAD, PrevR2)
                dZref = min( dZref, dMaxZ1)
                local MovH = { Z = EgtIf( dZref > EMT.L3o, dZref, EMT.L3o)}
-               MovH.X = -EMT.L2o ; MovH.B = EgtClamp( PrevR2, -90, 90) ; MovH.C = PrevR1 ;
+               MovH.X = -dXPos ; MovH.B = EgtClamp( PrevR2, -90, 90) ; MovH.C = PrevR1 ;
                EmitMoveDataHead( 1, MovH)
                if EMT.HEAD == 'H12' and ( abs( dSafeC1 - PrevR1) > 30.1 or abs( dSafeB1 - PrevR2) > 30.1) then
                   EmitMoveDataHead( 1, { Z=dMaxZ1, B=0})
@@ -2771,7 +2774,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
                EmitMoveDataHead( 1, { Z=dMaxZ1})
             else
                local MovH = { Z = dMaxZ1}
-               MovH.X = -EMT.L2o ; MovH.B = PrevR2 ; MovH.C = PrevR1 ;
+               MovH.X = -dXPos ; MovH.B = PrevR2 ; MovH.C = PrevR1 ;
                EmitMoveDataHead( 1, MovH)
             end
             if bXhome then
@@ -2783,7 +2786,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
          -- altrimenti sega a catena
          else
             -- ribadisco movimento perchè in G141 si aspetta sempre tutti i valori
-            local MovH = { X = -EMT.L2o, Z = EMT.L3o, B = PrevR2, C = PrevR1}
+            local MovH = { X = -dXPos, Z = EMT.L3o, B = PrevR2, C = PrevR1}
             EmitMoveDataHead( 1, MovH)
             EmitMoveDataHead( 1, { Z=dSafeZ1, B=dSafeB1})
             if EMT.SB > 650 and abs( EMT.R3) < 0.1 then
@@ -2818,7 +2821,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
             local dZref = dSafeZ2 + GetZExtra( EMT.HEAD, PrevR2)
             dZref = min( dZref, dMaxZ2)
             local MovH = { Z = EgtIf( dZref > EMT.L3o, dZref, EMT.L3o)}
-            MovH.X = -EMT.L2o ; MovH.B = EgtClamp( PrevR2, -90, 90) ; MovH.C = PrevR1 ;
+            MovH.X = -dXPos ; MovH.B = EgtClamp( PrevR2, -90, 90) ; MovH.C = PrevR1 ;
             EmitMoveDataHead( 2, MovH)
             if EMT.HEAD == 'H22' and ( abs( dSafeC2 - PrevR1) > 30.1 or abs( dSafeB2 - PrevR2) > 30.1) then
                EmitMoveDataHead( 2, { Z=dMaxZ2, B=0})
@@ -2828,7 +2831,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
             EmitMoveDataHead( 2, { Z=dMaxZ2})
          else
             local MovH = { Z = dMaxZ2}
-            MovH.X = -EMT.L2o ; MovH.B = PrevR2 ; MovH.C = PrevR1 ;
+            MovH.X = -dXPos ; MovH.B = PrevR2 ; MovH.C = PrevR1 ;
             EmitMoveDataHead( 2, MovH)
          end
          if bXhome then
@@ -2840,7 +2843,7 @@ function EmitZmax( bReset, bEnd, bXhome, PrevR1, PrevR2, bSplitCut, bUsePrevDelt
       -- altrimenti sega a catena
       else
          -- ribadisco movimento perchè in G141 si aspetta sempre tutti i valori
-         local MovH = { X = -EMT.L2o, Z = EMT.L3o, B = PrevR2, C = PrevR1}
+         local MovH = { X = -dXPos, Z = EMT.L3o, B = PrevR2, C = PrevR1}
          EmitMoveDataHead( 2, MovH)
          EmitMoveDataHead( 2, { Z=dSafeZ2, B=dSafeB2})
          if EMT.SB > 650 and abs( EMT.R3) < 0.1 then

Common_ONE-PF.mlpe

@@ -1003,14 +1003,20 @@ function OnSimulMoveStart()
                   bMoveZbeforeX = true
                end
 
+               -- se vado in posizione speciale rotazione assi, poi devo ritornare alla X vera di lavoro
+               local dMoveXtoFinalPosition = false
                local dXref = EMT.L2
                if  EMT.HEAD == 'H12' and  -EMT.L2 < -LimX1PlRotSaw  then
                   dXref = LimX1PlRotSaw
                   SimulMoveAxis( 'X1', dXref, MCH_SIM_STEP.RAPID)
+                  dZref = Z1Home + GetZExtra( EMT.HEAD, EMT.R2)
+                  dMoveXtoFinalPosition = true
                elseif not bMoveZbeforeX then
                   SimulMoveAxis( 'X1', dXref, MCH_SIM_STEP.RAPID)
                else
                   SimulMoveAxis( 'X1', LimX1PlRotSaw, MCH_SIM_STEP.RAPID)
+                  dZref = Z1Home + GetZExtra( EMT.HEAD, EMT.R2)
+                  dMoveXtoFinalPosition = true
                end
 
                -- caso speciale per trave alta con rotazione lama pericolosa (tolto "and EMT.SB > 379")
@@ -1021,6 +1027,9 @@ function OnSimulMoveStart()
                   if bMoveZbeforeX then
                      SimulMoveAxis( 'Z1', EMT.L3, MCH_SIM_STEP.RAPID)
                   end
+                  if dMoveXtoFinalPosition then
+                     SimulMoveAxis( 'X1', EMT.L2, MCH_SIM_STEP.RAPID)
+                  end
                -- caso standard
                else
                   SimulMoveAxis( 'Z1', dZref, MCH_SIM_STEP.RAPID)

UpdateLog.txt

@@ -1,7 +1,7 @@
            ==== Common_ONE-PF Update Log ====
 
-Versione 2.6-- (--/--/2024)
+Versione 2.6j1 (08/10/2024)
-- (SIM-GEN) Corretto movimento in Home in caso di lama e movimento rulliera di carico. Ticket#2054
+-- (SIM-GEN) Corretto primo movimento di approccio al pezzo. Ticket#2093
 
 Versione 2.6i2 (13/09/2024)
 - (GEN) Migliorato calcolo chiusura paratia rulli con aggiornamento lunghezza della barra in caso di ultimo taglio e grezzo residuo in coda. Ticket#2017

Version.lua

@@ -3,7 +3,7 @@
 
 local InfoCommon_STD_PP = {
    NAME = 'Common_ONE-PF',            -- nome script PP standard
-   VERSION = '2.6--',                 -- versione script
+   VERSION = '2.6j1',                 -- versione script
    MIN_MACH_VER_PP_COMMON = '2.5k1'   -- versione minima kernel
 }