- Correzioni e migliorie su pezzo di esempio

- Gestione avvio script solo quando eseguiti precedenti
- Correzioni varie

LuaLibs/AddManData.lua

@@ -1,4 +1,4 @@
--- AddManData.lua by Egaltech s.r.l. 2022/03/28
+-- AddManData.lua by Egaltech s.r.l. 2022/04/12
 -- Raccolta costanti generali per Stampa 3d
 
 -- Tabella per definizione modulo
@@ -34,13 +34,14 @@ KEY_SLICE_STEP = "StrandH"
 KEY_SHELLS_NBR = "StrandCount"
 KEY_STRAND = "StrandW"
 KEY_OFFSET_SLICE ="Offset"
-KEY_START_POINT = "StartingPoint"
+KEY_START_POINT = "StartPoint"
 KEY_PRINT_ORDER = "StrandOrder"
 KEY_PRINT_DIRECTION = "Direction"
 KEY_TYPE = "Type"
 KEY_LINK_TYPE = "LinkType"
 KEY_LINK_PARAM = "LinkParam"
 KEY_LINK_DIST="LinkDist"
+KEY_LINK_ZUP = "LinkZup"
 KEY_FLOOR_NBR = "FloorCount"
 KEY_SPEED = "Speed"
 KEY_FEED = "Feed"
@@ -63,32 +64,30 @@ KEY_LEAD_OUT_ORTHO_DIST= "LeadOutOrthoDist"
 KEY_OFFSET_LEAD_POINT = "OffsetLeadPoint"
 
 TYPE = {
-   OUTER_SHELL = 0,
-   INNER_SHELL = 1,
-   INFILL = 2,
-   LINK = 3,
+   OUTER_SHELL = 1,
+   INNER_SHELL = 2,
+   INFILL = 3,
+   LINK = 4,
 }
 
 PRINT_ORDER = {
-   INT_EXT_INF = 0,
    EXT_INT_INF = 1,
-   INF_EXT_INT = 2,
-   INF_INT_EXT = 3,
+   INF_INT_EXT = 2,
 }
 
 PRINT_DIRECTION = {
-   CCW = 0,
-   CW = 1,
+   CCW = 1,
+   CW = 2,
 }
 
 LINK_TYPE = {
-   LINEAR = 0,
-   BIARC = 1,   
+   LINEAR = 1,
+   BIARC = 2,   
 }
 
 LEAD_TYPE = {
-   LINEAR = 0,
-   ARC = 1,
+   LINEAR = 1,
+   ARC = 2,
 }
 
 
@@ -105,16 +104,41 @@ RESULT_READ_PROG = 'ResultReadProg'
 
 KEY_RESULT = 'Result'
 KEY_PALETTE = 'Palette'
+KEY_LAYER_VIEW = 'LayerView'
+KEY_SHELL_VIEW = 'ShellView'
+KEY_INNER_NUM = 'InnerNum'
+KEY_SEL_LAYER = 'SelLayer'
+KEY_SLICE_ADV_MODE = 'SliceAdvMode'
+KEY_SLICE_ADV_PERC = 'SliceAdvPerc'
 
 RESULT = {
-   OK = 0,
-   KO_MINUS = 1,
-   KO_PLUS = 2,
+   OK = 1,
+   KO_MINUS = 2,
+   KO_PLUS = 3,
 }
 
 PALETTE_TYPE = {
-   IN_OUT = 0,
-   RESULTS = 1,
+   IN_OUT = 1,
+   RESULTS = 2,
 }
+
+LAYER_VIEW_TYPE = {
+   ALL = 1,
+   TILL_SEL = 2,
+   ONLY_SEL = 3,
+}
+SHELL_VIEW_TYPE = {
+   ALL = 1,
+   OUTER = 2,
+   INNER = 3,
+   INFILL = 4,
+}
+SLICE_ADV_TYPE = {
+   ALL = 1,
+   OUTER = 2,
+   INNER = 3,
+   INFILL = 4,
+}
+
 ---------------------------------------------------------------------
 return AddManData